Funai DWT1905 User Manual

FEATURES
181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels.
PLL Frequency Synthesized Tuning- Provides free and easy channel selection and lets you tune directly to any channel using the channel number buttons on the remote control.
Sleep Timer
Closed Caption Decoder
V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV.
Tinted, Bright Black Matrix Picture Tube
Full-Function Remote Control
On-Screen Function Display
Front AV Input
Resume Function- If the power fails or is disconnected while the TV is on, the TV will turn on automatically when the power resumes.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con­nected to the grounding system of the building as close to the point of cable entry as practical.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equip­ment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unautho­rized change or modification is made.
IF YOU NEED ADDITIONAL ASSISTANCE WITH SET-UP OR OPERATING AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-605-8379 OR VISIT OUR WEB SITE AT http://www.funai-corp.com
Owner’s Manual
1EMN20269 Printed in Malaysia
L2314UQ * * * * *
DWT1905
19 INCH COLOR TELEVISION
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI­ANCE TO RAIN OR MOISTURE.
IMPORTANT SAFEGUARDS
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SER­VICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT DAN­GEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRE­SENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
The important note is located on the rear of the cabinet.
1. READ INSTRUCTIONS-All the safety and operating instructions should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS-The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS-All warnings on the appliance and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS-All operating and use instructions should be followed.
5. CLEANING-Unplug TV from the wall outlet before cleaning. Do not use liquid cleaners or aerosol clean­ers. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupt­ed service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.
6. ATTACHMENTS-Do not use attachments not recom­mended by the TV manufacturer as they may cause hazards.
7. WATER AND MOISTURE-Do not use this TV near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. ACCESSORIES-Do not place this TV on an unstable cart, stand, tripod, bracket, or table. The TV may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufac­turer, or sold with the TV. Any mounting of the appliance should follow the man­ufacturer’s instructions and should use a mounting accessory recommended by the manufacturer. An appli­ance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
AMEUBLES- Cet appareil ne doit être placé que sur un meuble (avec ou sans roulettes) recommandé par le fabricant. Si vous l’installez sur un meuble à roulettes, déplacez les deux ensembles avec précaution. Un arrêt brusque, l’utilisation d’une force excessive et des surfaces irrégulières risquent de déstabiliser l’ensemble et de le renverser.
9. VENTILATION-Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the TV on a bed, sofa, rug, or other similar sur­face. This TV should never be placed near or over a radiator or heat register. This TV should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufactur­er’s instructions have been adhered to.
10. POWER SOURCES-This TV should be operated only from the type of power source indicated on the mark­ing label. If you are not sure of the type of power sup­ply to your home, consult your appliance dealer or local power company. For TVs intended to operate from battery power, or other sources, refer to the oper­ating instructions.
11. GROUNDING OR POLARIZATION-This TV is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. POWER-CORD PROTECTION-Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, con-
venience receptacles, and the point where they exit from the appliance.
13. OUTDOOR ANTENNA GROUNDING-If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to pro­vide some protection against voltage surges and built­up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding elec­trode. (Fig. A)
14. LIGHTNING-For added protection for this TV receiv­er during a lightning storm, or when it is left unattend­ed and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable sys­tem. This will prevent damage to the TV due to light­ning and power-line surges.
15. POWER LINES-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or cir­cuits as contact with them might be fatal.
16. OVERLOADING-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
17. OBJECT AND LIQUID ENTRY-Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liq­uid of any kind on the TV.
18. SERVICING-Do not attempt to service this TV your­self as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE-Unplug this TV from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged or
frayed.
b. If liquid has been spilled, or objects have fallen into
the TV.
c. If the TV has been exposed to rain or water. d. If the TV does not operate normally by following the
operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified techni­cian to restore the TV to its normal operation.
e. If the TV has been dropped or damaged in any way. f. When the TV exhibits a distinct change in performance,
this indicates a need for service.
20. REPLACEMENT PARTS-When replacement parts are required, be sure the service technician uses replace­ment parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.
21. SAFETY CHECK-Upon completion of any service or repairs to this TV, ask the service technician to perform routine safety checks to determine that the TV is in proper operating condition.
22. HEAT-This TV product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ELECTRIC SERVICE EQUIPMENT
GROUND CLAMP
NEC - NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING
ELECTRODE SYSTEM (NEC ART 250, PART H)
S2898A
GROUND CLAMPS
GROUNDING CONDUCTORS (NEC SECTION 810-21)
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
ANTENNA LEAD IN WIRE
PRECAUTIONS
Place your TV in a room with adequate ventilation.
Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.
Do not place your TV on soft surfaces, such as rugs or blankets.
Leave enough room for air to circulate around the bottom, top and back of the set.
The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows:
DURATION:
PAR TS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from
the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date
of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail pur­chase will be required together with the product to obtain service under this warranty. This warranty shall not be extended to any other person or transferee. This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not sup­plied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alter­ation, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED SER­VICE CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO A FUNAI AUTHO­RIZED SERVICE FACILITY.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS WILL BE CHARGED.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VA RY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE.
To locate your nearest FUNAI Authorized Service Center or general service procedure, please call or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-605-8379
http://www.funai-corp.com
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Date of Purchase Dealer Purchase from Dealer Address
Dealer Phone No. Model No. Serial No.
PORTABLE CART WARNING
S3126A
SYMBOLE D'AVERTISSEMENT POUR
LES COMPOSANTES
APPAREIL ET MEUBLE A ROULETTES
S3126A
VIDEO AUDIO EARPHONE
VOLUME
CHANNEL
MENU
P O
W E
R
123
456
789
0 +100
DISPLAY
VOL
CH
CH
VOL
SLEEP
CHANNEL
RETURN
MUTE
GAME
POWER
MENU
PREPARATION FOR USE
[ANTENNA CONNECTION] [CATV/SATELLITE CONNECTION]
CONNECTIONS
ANT.IN
ANT.. IN
OUT IN
UHF
VHF
VHF/UHF
VHF/UHF Combiner
OR
OR
75-ohm Coaxial Cable
From Cable System
From Cable System or Satellite Antenna
CATV Box
*
or Satellite Box
*Some cable TV systems use scrambled signals and
require a special converter to receive these channels. Consult your local cable company.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT.
MISE EN GARDE: POUR ÉVITER LES RISQUES D’ÉLECTROCUTION, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
[EXTERNAL CONNECTION]
Front AUDIO/VIDEO INPUT
VIDEO AUDIO
Video Cable
Audio Cable
Video GameVideo Camera
Front of this TV
Notes:
If you hit [GAME] when the TV is off, the TV turns on and enters in Game mode.
If you adjust another picture control while in Game mode, this mode will automatically be canceled.
ex.
Cables used here are available on the market.
OPERATIONS
Note:
If some digits appear in the corner of the screen when the unit is turned on at the first time, hit
[POWER] without unplugging the power cord.
REMOTE CONTROL AND FRONT PANEL FUNCTION
POWER button
To turn TV on/off
Channel number buttons
CH(ANNEL) KK/ LLbuttons
MENU button
GAME button SLEEP button
DISPLAY button
To display CH No./Audio Status
CHANNEL RETURN button
To return previous screen
MUTE button
VOL(UME) KK/ LLbuttons
To select channels
To view on-screen menu
To adjust volume
Infrared Sensor Window
CHANNEL XX/YYbuttons
To select channels
VOLUME XX/YYbuttons
To adjust volume
MENU button
To view on-screen menu
AUDIO input jack
VIDEO input jack
INSTALLING THE BATTERIES
Install two AA batteries (supplied) matching the polarity indicated inside battery compartment of the remote con­trol.
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
2
1
3
UHF/VHF Rod Antenna (Not supplied)
OR
SELECTING AUDIO/VIDEO INPUT
You can select external input jacks by hitting [GAME] on the remote control.
EARPHONE jack
1
1
To use external input
Picture: GAME (ON) Input:
External
2
2
15
To return to TV channel
In Game mode, you can use front input jacks with suitable picture adjustments for video games.
(OUT)
(IN)
(IN)
(OUT)
2
2
[-]
GAME MODE
[+]
OFF ON
VIDEO
To cancel Game mode only
3
3
Picture: Customized Input: External
15
To return to TV channel
You can enter into Video mode from Game mode by adjusting a Picture control.
2 times
1
1
To use external input
Picture: GAME (ON) Input:
External
Select “PICTURE”
Note:
For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. IN jack before moving the unit.
After 10 seconds
POWER button
To TV on/off
RF Cable
RF Cable
GAME
GAME
GAME
GAME
GAME
MENU
VOL
GAME
OPERATIONS (Continued)
OPTIONAL SETTINGS
2
2
Adjust the setting
3
3
GAME MODE
Set to the most suitable position for video games.
[-] : OFF [+] : ON
BRIGHT
Adjust until the darkest parts of the picture are as bright as you prefer.
[-] : decrease brightness [+] : increase brightness
CONTRAST
Adjust to increase or decrease contrast.
[-] : decrease contrast [+] : increase contrast
COLOR
Adjust to be brilliant or pale color.
[-] : be pale color [+] : be brilliant color
TINT
Adjust to obtain natural skin tones.
[-] : add red [+] : add green
SHARPNESS
Adjust to detail in the picture.
[-] : make soft [+] : make clear
Notes:
The display will disappear automatically after 10 seconds unless you press any buttons.
Magnetism from nearby appliances and speakers might affect the color of the TV picture. If this happens, hit [POWER] to turn off the TV and turn it on again after about 30 minutes.
CHANNEL SETTING
1
1
[AUTO PRESET CHANNELS]
As the initial setting, this TV has memorized all channels, including the ones not available in your area. This feature automatically puts only available channels into the memory.
1
1
The tuner scans and memorizes all available channels in your area.
2
2
Select the desired language
3
3
To exit the menu
Notes:
The TV distinguishes between standard TV channels and cable (CATV) channels.
The TV may recognize TV channels as CATV channels if reception condition is poor. If this happens, check the antenna connections and try steps 2 to 3 again when reception conditions are better.
If there is no TV sig­nal input, “NO TV SIGNALS” will appear on the display after the completion of channel scanning.
[ADDING/DELETING CHANNELS]
You can add or delete channels manually.
LANGUAGE SELECTION
3
3
When the scanning is completed, the lowest memorized channel appears on the TV screen.
1
1
2
2
Select the channel you wish
4
4
Note:
The menu will disappear automatically after about 10 seconds.
Notes:
If closed captioning is not broadcast, you cannot receive it and nothing is displayed.
When your TV receives a special effects playback signal (i.e., Search, Slow and Still) from a VCR’s video output channel (CH3 or CH4), the TV may not display the correct caption or text.
Captions and texts may not match the TV voice exactly.
Interference may cause the closed caption system not to function properly.
The caption or text characters will not be displayed while the menu display or func­tions display is shown.
If a black box appears on the screen, this means that the TV is set to TEXT mode. To clear screen, select CAPTION [C1], [C2] or [OFF].
Add: light blue Delete: light red
2
2
3
3
[
GAME MODE
][
BRIGHT
][
CONTRAST
]
[
SHARPNESS
][TINT] [COLOR]
Select an item to adjust
Select [ENG]
[ENG(lish)] [ESP(añol)]
[FRA(nçais)]
Select “CHANNEL SET”
Select “CHANNEL SET”
Select “ADD/DELETE”
Select “AUTO PRESET CH”
15
ADD/DELETE
Add or delete the channel
You may view specially labeled (cc) TV pro­grams, movies, news and prerecorded tapes, etc. with either a dialogue caption or text dis­play added to the program.
1
1
2
2
Select the desired caption mode
To exit the menu
3
3
[OFF] [C1] [C2]
[T2] [T1]
Select “CAPTION”
[CAPTION MODE (C1, C2)]
CAPTION1 (C1) displays standard closed captions (what a character is saying).
CAPTION2 (C2) displays foreign language closed captions (foreign language words showing what a character is saying).
There are three ways of displaying accord­ing to programs: Paint-on mode: Displays input characters
on the screen immediately.
Pop-on mode : Once characters are stored
in memory, they are dis­played all at once.
Roll-up mode : Displays the characters con-
tinuously by scrolling (max. 4 lines).
[TEXT MODE (T1, T2)]
TEXT1 (T1) and TEXT2 (T2) display half-screen text by scrolling (such as a channel guide, schedule or announcement).
CLOSED CAPTION
...
+
...
Notes:
When you disconnect the unit from the AC outlet or when you have a power failure, the sleep time will be lost.
To cancel the sleep timer, hit [SLEEP] repeatedly until “SLEEP 0” is displayed.
The Sleep Timer Setting display will disap­pear automatically after 10 seconds of the operation.
SLEEP TIMER SETTING
1
1
2
2
The time increases by 10 minutes up to 90.
repeatedly
PICTURE ADJUSTMENT
1
1
Select “PICTURE”
MENU
CH
CH
VOL
CH
CH
VOL
PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF]
ADD/DELETE AUTO PRESET CH
NO TV SIGNALS
MENU
CH
CH
VOL
VOL
CH
CH
VOL VOL
PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF]
ADD/DELETE AUTO PRESET CH
MENU
CH
CH
PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF]
VOL VOL
MENU
SLEEP
SLEEP
MENU
VOL
CH
CH
VOL
VOL
PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF]
[-]
SLEEP 0
SLEEP 10
BRIGHT
[+]
MENU
CH
CH
PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF]
VOL VOL
MENU
Loading...
+ 6 hidden pages