Funai 6419CTB, 6413CTB User Manual

This TV can receive C1 and C2 of Caption and Text.
Caption Mode
(1)Characters can be displayed on the TV screen when the received broadcast signal contains the
Caption Signals.
(2)Paint-on mode: Displays input characters on the screen immediately.
Pop-on mode: Once characters are stored in memory, it is displayed all at once. Roll-up mode: Displays the characters continuously by scrolling (max. 4 lines)
not be displayed.
Text Mode
(1)Displays the text on the screen by scrolling (max. 7 lines) (2)If the received broadcast signal does not contain the caption or text signal, no change will
occur.
Notes:
(1)When your TV receives a special effects playback signal (i.e., Search, Slow, Still) from a
VCR’s video output channel (CH3 or CH4), your TV may not display the correct caption or
text. (2)Captions and texts may not match the TV voice exactly. (3)Interference may cause the closed caption system not to function properly. (4)The caption or text characters will not be displayed while the menu display or function’s dis-
play is shown. (5)If you see this screen!!
If your TV displays a black box on the screen, this means that your TV is set to TEXT mode. To clear screen, select CAPTION C1, C2 or CAPTION [OFF].
ANTENNA/CABLE CONNECTIONS
PRECAUTION
Place your TV in a room with adequate ventilation.
Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.
Do not place your TV on soft surfaces, such as rugs or blankets.
Leave enough room for air to circulate around the bottom, top and back of the set.
FEATURES
Tinted, Bright Black Matrix Picture Tube
181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels.
PLL Frequency Synthesized Tuning- The latest PLL frequency synthesized electronic
tuning system provides free and easy channel selection, and lets you tune directly to any chan­nel using the channel number buttons (0~9 and +100-key) on the remote control.
On-Screen Function Display.
Full-Function Remote Control
Sleep Timer
Closed Caption Decoder- You may view specially labeled (cc) TV programs, movies, news,
prerecorded tapes, etc. with either a dialogue caption or text display added to the program.
Auto Shut Off Function- If there is no air signal input from the antenna terminal and no
operation for 15 minutes, the TV will turn itself off automatically.
V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV.
COLOR TELEVISION
6413CTB (13 inch) 6419CTB (19 inch)
Date of Purchase Dealer Purchase from Dealer Address
Dealer Phone No. Model No. Serial No.
The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.
ANT.IN
CLOSED CAPTION
UHF Antenna (Not supplied)
VHF Antenna
(Not supplied)
VHF/UHF Combiner (Not supplied)
VHF/UHF Combination Antenna (Not supplied)
UHF/VHF Rod Antenna (Supplied with 13
inch model only)
OR
OR
ANT. IN
OUT IN
75-ohm Coaxial Cable
From Cable System
From Cable System or Satellite Antenna 75-ohm Coaxial Cable
CATV Box
*
or Satellite Box (Not supplied)
*Some cable TV systems use scram-
bled signals and require a special con­verter to receive these channels. Consult your local cable company.
IF YOU NEED ADDITIONAL ASSISTANCE FOR SET-UP OR OPERATING AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-287-4871.
Owner’s Manual
0EMN01839 Printed in China
L1354CE * * * * *
This Owner’s Manual is made of recycled paper.
SYLVANIA HOME ENTERTAINMENT WARRANTY
We appreciate your purchase of a SYLVANIA Home Entertainment product. We take pride in the quality of our products and have manufactured your new Home Entertainment unit to exacting quality standards. We feel confident that in normal use, it will provide you with satisfactory performance. However, should you experience difficulty, you are protected under the provisions of this warranty. SYLVANIA Home Entertainment products are warranted against manufacturing defects in materials and workmanship in normal use for the following periods from the date of purchase by the original user, and is conditional upon the unit being installed and used as directed in the instruction manual.
Product Labour Parts Picture Tube
Colour Televisions 1 Year 1 Year 3 Years Remote Control 90 Days 90 Days B/W Televisions 90 Days 1 Year 1 Year
SYLVANIA s obligation under this warranty shall be limited to the repair, including all necessary parts and the cost of the labour connected therewith, or at our option the exchange of any Home Entertainment product which shows evidence of a manufacturing defect within the warranty period. Replacement parts, furnished in connection with this warranty shall be warranted for a period equal to the unexpired portion of the original equipment warranty.
CUSTOMER OBLIGATIONS
This warranty applies to the product from the original date of purchase at retail. Therefore, the owner must provide a copy of the original, dated bill of sale. No warranty service will be performed without a bill of sale. Transportation to and from the service depot is the responsibility of the owner.
WARRANTY EXCLUSIONS
This warranty is extended to SYLVANIA Home Entertainment products purchased and used in Canada. This warranty shall not apply to appearance or accessory items including but not limited to: antenna, cabinet, cabinet parts, knobs, batteries, connecting cables. This warranty shall, in addition, not apply to damages due to handling, transportation, unpacking, set-up, installation, customer adjustments that are covered in the instruction book, repair or replacement of parts supplied by other than the SYLVANIA authorized service depot, any malfunction or failure caused by or resulting from abnormal environmental conditions, improper unauthorized service, improper maintenance, modifications or repair by the consumer, abuse, misuse, neglect, accident, fire, flood, or other Acts of God, and incorrect line voltage. This Home Entertainment product is only warranted to the original retail purchaser. This warranty becomes void in the event of commercial or rental use. This warranty becomes void in the event serial numbers are altered, defaced or removed. SYLVANIA reserves the right to make changes in design or to make additions to or improvements upon this product without incurring any obligation to install the same on products previously manufactured. The foregoing is in lieu of all other warranties expressed or implied and SYLVANIA neither assumes nor authorizes any person to assume for it any other obligation or liability in connection with the sale or service of this product. In no event shall SYLVANIA or its SYLVANIA dealers be liable for special or consequential damage arising from the use of this product, or for any delay in the performance of this warranty due to cause beyond our control. The purchaser may have other rights under existing provincial or federal laws, and where any terms of this warranty are prohibited by such laws, they are deemed null and void, but the remainder of the warranty shall remain in effect.
HOW TO OBTAIN SERVICE
Should this product require service, you may obtain specific information on how to obtain service by contacting the SYLVANIA Dealer from whom this product was purchased, or by contacting us directly:
SONIGEM SERVICE
300 Alden Road
Markham, Ontario
L3R 4C1
PHONE: (905) 940-5089 FAX: (905) 940-2303
1-800-287-4871
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Before plugging the UHF/VHF Rod Antenna into the ANT(enna). IN jack, check that the pin is not bent. If it is bent, straight­en the pin as illustrated, then plug the pin into the ANT(enna). IN jack. (Rod Antenna is included in 13 inch model only)
Bent pin
Cable
Plug
(Needs to be straightened) (Straight pin)
NOTE:CHANNEL SET UP MUST BE COMPLETED BEFORE THE SET WILL FUNC-
TION PROPERLY. SEE INSIDE FOR PROCEDURE.
L1354.QX33 01.5.14 5:00 PM Page 1
14.GAME button- Press to set the Game
mode and external input mode at the same time. Press the GAME button again to exit the this mode.
15.ANT(enna). IN jack- Connect to an anten-
na, cable system, or satellite system.
16.AC cord- Connect to a standard AC outlet
(120V/60Hz). NOTE: Remove the AC cord from the hook to avoid breaking a wire before you connect to a standard AC outlet.
INSTALLING THE BATTERIES
Slide the battery compartment cover on the remote unit.
Insert 2 "AA" penlight batteries into battery compartment in the direction as indicated by the polarity (+ / -) markings. Batteries installed with incorrect polarity may damage the remote unit.
Replace the cover.
3
2
1
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI­ANCE TO RAIN OR MOISTURE.
IMPORTANT SAFEGUARDS
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SER­VICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THATDAN­GEROUS VOLTAGE CONSTI-TUTING A RISK OF ELECTRIC SHOCK IS PRE­SENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANTOPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANY-ING THE APPLIANCE.
The important note is located on the rear of the cabinet.
1. Read instructions-All the safety and operating instruc­tions should be read before the appliance is operated.
2. Retain Instructions-The safety and operating instruc­tions should be retained for future reference.
3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow Instructions-All operating and use instructions should be followed.
5. Cleaning-Unplug TV from the wall outlet before clean­ing. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupt­ed service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.
6. Attachments-Do not use attachments not recommended by the TV manufacturer as they may cause hazards.
7. Water and Moisture-Do not use this TV near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. Accessories-Do not place this TV on an unstable cart, stand, tripod, bracket, or table. The TV may fall, caus­ing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the TV. Any mounting of the appliance should follow the manufacturer’s instructions and should use a mounting accessory recommended
by the manufacturer. An appliance and cart combina­tion should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
9. Ventilation-Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the TV on a bed, sofa, rug, or other similar sur­face. This TV should never be placed near or over a radiator or heat register. This TVshould not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufac­turers instructions have been adhered to .
10.Power Sources-This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TVs intended to operate from bat­tery power, or other sources, refer to the operating instructions.
11.Grounding or Polarization-This TV is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12.Power-Cord Protection-Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
PORTABLE CART WARNING
S3126A
13.Outdoor Antenna grounding-If an outside antenna or cable system is connected to the TV, be sure the anten­na or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPANo. 70, provides information with respect to proper grounding of the mast and supporting struc­ture, grounding of the lead-in wire to an antenna dis­charge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding elec­trodes, and requirements for the grounding electrode. (Fig. A)
14.Lightning-For added protection for this TV receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning and power-line surges.
15.Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
16.Overloading-Do not overload wall outlets and exten­sion cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV.
18.Servicing-Do not attempt to service this TV yourself as opening or removing covers may expose you to dan­gerous voltage or other hazards. Refer all servicing to qualified service personnel.
19.Damage Requiring Service-Unplug this TV from the wall outlet and refer servicing to qualified service per­sonnel under the following conditions:
a. When the power supply cord or plug is damaged or
frayed.
b.If liquid has been spilled, or objects have fallen into
the TV.
c. If the TV has been exposed to rain or water. d.If the TV does not operate normally by following the
operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified techni­cian to restore the TV to its normal operation.
e. If the TV has been dropped or damaged in any way. f. When the TV exhibits a distinct change in perfor-
mance-this indicates a need for service.
20.Replacement Parts-When replacement parts are required, be sure the service technician uses replace­ment parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.
21.Safety Check-Upon completion of any service or repairs to this TV, ask the service technician to perform routine safety checks to determine that the TV is in proper operating condition.
22.Heat-This TV product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ELECTRIC SERVICE EQUIPMENT
GROUND CLAMP
NEC - NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING
ELECTRODE SYSTEM (NEC ART 250, PART H)
S2898A
GROUND CLAMPS
GROUNDING CONDUCTORS (NEC SECTION 810-21)
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
ANTENNA LEAD IN WIRE
OPERATING CONTROLS AND FUNCTIONS
- FRONT PANEL - - REAR PANEL -
1. VIDEO (in) jack- Connect to the video
output jack of a video camera or VCR.
2. AUDIO (in) jack- Connect to the audio
output jack of a video camera or VCR.
3. EARPHONE jack- To connect earphone
(not supplied) for personal listening.
4. MENU button- Press to display the menu
on the TV screen.
5. VOLUME /buttons- Press to control
the volume level. Press to determine a setting mode from the menu on the TV screen. (only the VOL button) Press to select or adjust from a particular menu. (for example: Language Selection, Channel Presetting, Closed Caption Selection, Picture Adjustment, V-CHIPSet Up)
6. CHANNEL /buttons- Press to select
memorized channel. NOTE:CHANNEL SET UP MUST BE COMPLETED BEFORE THE SET WILL FUNCTION PROPERLY. SEE INSIDE FOR PROCEDURE. Press to select a setting mode from the menu on the TV screen. Press to select item you want to adjust in the picture control mode.
7. POWER button- Press to turn the TV ON
and OFF.
8. Infrared Sensor Window- Receives the
infrared control signals from the remote control unit.
9. CHANNEL NUMBER button- Press two
digits to directly access the desired channel. Remember to press a "0" before a single digit channel. +100 button- Press to select cable channels which are equal or greater than number
100.
10.MUTE button- Press the MUTE button to
turn off the sound portion of the TV pro­gram. (Volume level display turns LIGHT RED from LIGHT BLUE.) Press the MUTE button again or press the VOL(ume) or button to restore sound.
11.CHANNEL RETURN button- Press this
button to go back to the previously viewed channel. For example, pressing the CHAN­NEL RETURN button once will change channel display from CH 3 (present chan­nel) to CH 10 (previously viewed channel), and pressing it a second time will return from CH 10 to CH 3.
12.DISPLAYbutton- Press to display the
channel number on the screen. If you press it again, the channel number will disappear.
13.SLEEP button- Press the SLEEP button to
display the sleep timer and start the func­tion. The shut off time can be determined by the number of times you press the but­ton. (0, 10, 20, 30,..90, 0 minutes)
- REMOTE CONTROL -
VIDEO VOLUME POWERCHANNELMENUEARPHONEAUDIO
12 34 5 6 7 8
ANT.IN
16 15
POWER
123
456
789
0 +100
DISPLAY
VOL
CH
CH
VOL
SLEEP
CHANNEL
RETURN
7
9
5
4
10
12
11
13
MUTE
MENU
6
GAME
14
This manual covers 13" and 19". The operation of the two models are exactly the same except the appearance. 19" model is illustrated in this manual.
L1354.QX33 01.5.14 5:00 PM Page 2
PREPARATION FOR USE
LANGUAGE SELECTION
If you want to change the language of the on-screen menu, follow the procedure below.
Connect the power cord to a standard AC outlet. Note: If some digits appear in the corner of the screen, press the POWER button without unplugging the power cord.
Press the POWER button to turn on the TV.
Press the MENU button so that the menu display appears on the TV screen.
Press the CH(annel) or button to point to "[ENGLISH]".
Select "ENGLISH" or "FRANÇAIS" = French by using the VOL(ume) or button.
Press the MENU button to exit the menu.
CHANNEL PRESETTING
NOTE:CHANNEL SET UP MUST BE COMPLETED BEFORE THE SET WILL FUNCTION
PROPERLY. To preset a channel or to change a preset channel, follow the procedure below.
Press the POWER button to turn on the TV.
Press the MENU button so that the menu display appears on the TV screen.
Press the CH(annel) or button to point to "CHANNEL SET". Then, press the VOL(ume) button.
Press the CH(annel) or button to point to "AUTO MEMO". Then, press the VOL(ume) button. The tuner scans and memorizes all active channels in your area.
The TV distinguishes between standard TV channels
and cable channels.
When AUTO MEMO action is completed, the lowest
memorized channel reappears on the screen.
When you press the CH(annel) ▲ or button after
selecting AUTO MEMO, the tuner will stop at the memorized channels only.
The TV may recognize TV channels to be CATV channels
by the receiving conditions. In this case, try AUTO MEMO action again in the fine receiving conditions.
[ADD/DELETE FUNCTION]
1)Press the MENU button so that the menu display appears on the TV screen.
2)Press the CH(annel) or button to point to "CHANNEL SET". Then, press the VOL(ume) button.
3)Press the VOL(ume) button so that "ADD/DELETE" is selected.
4)Use the CH(annel) or button to select the channel you wish to put into memory or to erase from memory. Note: The display will return to the screen in about 10 seconds. Perform "ADD/DELETE" function while this display appears on the screen.
Press the VOL(ume) ▲ or button to light up the channel number
in LIGHT BLUE if you wish to add the channel into memory.
Press the VOL(ume) ▲ or button to light up the channel number
in LIGHT RED if you wish to erase the channel from memory.
5)Press the MENU button to exit the menu.
RESUME FUNCTION
If the power fails or is disconnected while the TV is powered on, the TV will turn on automatical­ly when the power resumes.
4
3
2
1
6
5
4
3
2
1
PICTURE CHANNEL SET [ENGLISH]FRANÇAIS V-CHIP SET UP CAPTION [OFF]
ADD/DELETE AUTO MEMO
ADD/DELETE AUTO MEMO
PICTURE CHANNEL SET [ENGLISH]FRANÇAIS V-CHIP SET UP CAPTION [OFF]
PICTURE CHANNEL SET [ENGLISH]FRANÇAIS V-CHIP SET UP CAPTION [OFF]
OPERATIONS
WATCHING ATV PROGRAM
1)Press the POWER button to turn on the TV.
2)Select the desired channel with the CH(annel) or button.
3)Adjust the volume to the desired listening level using the VOL(ume) or button.
4)Adjust picture controls for a natural looking image. (See "PICTURE ADJUSTMENT".)
SETTING THE SLEEP TIMER
The sleep timer function enables you to shut off the power without pressing the POWER button after a desired time period.
1)Press the POWER button to turn on the TV and press the SLEEP button on the remote control .
2)You may change the sleep time with pressing the SLEEP button on the remote control repeatedly. The timer is set up to 90 minutes, 10 minutes each time the SLEEP button is pushed. (The timer display counts up and sleep timer will be displayed on the screen when you press the SLEEP button on remote control.) Note: When you disconnect the unit from the AC outlet, or if you have a power failure, the sleep time will be lost.
CLOSED CAPTION SELECTION
SLEEP 10
To cancel the sleep timer:
Press the SLEEP button repeated­ly until "SLEEP 0" is displayed.
You may view specially labeled (cc) TV pro­grams, movies, news, prerecorded tapes, etc. with either a dialogue caption or text display added to the program.
1)Press the MENU button so that the menu display appears on the TV screen.
2)Press the CH(annel) or button to point to "CAPTION".
3)Press the VOL(ume) or button to select the mode you wish.
4)When done, press the MENU button to exit the menu.
PICTURE CHANNEL SET [ENGLISH]FRANÇAIS V-CHIP SET UP CAPTION [OFF]
PICTURE CHANNEL SET [ENGLISH]FRANÇAIS V-CHIP SET UP CAPTION [ C1]
PICTURE CHANNEL SET [ENGLISH]FRANÇAIS V-CHIP SET UP CAPTION [ C2]
PICTURE CHANNEL SET [ENGLISH]FRANÇAIS V-CHIP SET UP CAPTION [ T1]
PICTURE CHANNEL SET [ENGLISH]FRANÇAIS V-CHIP SET UP CAPTION [ T2]
: Press the VOL(ume) ▲ or ▼ button.
GAME MODE
Set to the most suitable position for TV GAME.
[+] : ON [ -] : OFF
BRIGHT
Adjust until the whitest parts of the picture are as bright as you prefer.
[+] : increase brightness [ -] : decrease brightness
CONTRAST
Adjust to increase or decrease contrast.
[+] : increase contrast [ -] : decrease contrast
COLOR
Adjust to be brilliant or pale color.
[+] : be brilliant color [ -] : be pale color
TINT
Adjust to obtain natural skin tones.
[+] : greenish tone [ -] : reddish tone
Notes:
In the above steps, the picture adjustment
display will disappear from the TV screen after about 10 seconds unless you press any buttons, even though you may not be fin­ished. Press the MENU and VOL(ume) button so that "PICTURE" is selected. Then, press the CH(annel) or button repeat­edly until the display returns to the screen.
If you adjust the other Picture control after
you set the Game mode to [ON], the Game mode is set to [OFF] automatically.
[USING THE GAME BUTTON]
You may also set the Game mode and external input mode at the same time by pressing the GAME button on the remote control. GAME appears on the TV screen.
To exit the Game mode and external input
mode, press the GAME button on the remote control again.
To cancel the Game mode only, adjust the
picture control. In this case, VIDEO instead of GAME appears on the TV screen.
When you press the GAME button if the TV
is off, the TV turns on and will be in the Game mode and external input mode auto­matically.
PICTURE ADJUSTMENT
1)Press the MENU button so that the menu display appears on the TV screen.
2)Press the VOL(ume) button so that "PICTURE" is selected.
3)Select the feature you wish to adjust with the CH(annel) or button and adjust it with the VOL(ume) or button.
[-]
GAME MODE
[+]
OFF ON
[-]
BRIGHT
[+]
[-]
CONTRAST
[+] [-]
COLOR
[+] [-]
TINT
[+]
: Press the CH(annel) or button.
PICTURE CHANNEL SET [ENGLISH]FRANÇAIS V-CHIP SET UP CAPTION [OFF]
PICTURE CHANNEL SET [ENGLISH]FRANÇAIS V-CHIP SET UP CAPTION [OFF]
L1354.QX33 01.5.14 5:00 PM Page 3
Loading...
+ 6 hidden pages