Fujitsu Technology Solutions 01TASTK278 User Manual
Introduction
The KBPC M multimedia keyboard offers you ease-of-use and functionality in a modern design:
•
Audio playback via integrated stereo loudspeakers (2 x 1 W) or headphones
•
Audio recording via integrated or external microphone
•
PC supported, convenient telephony via telephone handset, headset (headphones with
microphone) or hands-free facility
•
simple switching between telephone handset/headset and hands-free facility with the handsfree button
•
direct connection of mouse, telephone handset/headset, stereo headphones and external
microphone to the keyboard (avoiding a mass of cables)
System requirements
Your PC must fulfill the following requirements if you want to use all the functions of the KBPC M
multimedia keyboard:
•
Audio board (sound card)
The audio board should have a stereo loudspeaker output or audio line output and a
microphone input.
•
Modem board
Your PC should have a modem with voice function. If possible, the voice signal output of the
modem should be routed via the audio board. (In a lot of multimedia PCs this connection is
already implemented internally.)
•
Communications software
No special demands are made on your communications software, just that it should be suited
to your requirements. It should be matched to your needs.
•
Quickstart function
Your PC should have a Quickstart function (e. g.
for your answering machine, fax or telephone, and also to save power.
•
Keyboard interface
Die Tastaturschnittstelle der Systemeinheit (5 V Versorgungsspannung) muß für mindestens
600 mA ausgelegt sein. This applies to all Siemens PCs (except notebooks).
Further information on these features is provided in the manuals for your PC and/or for the specified
system components.
BIOSFaX
) in order to ensure reliable reception
A26381-K276-Z100-3-5E19
English - 1
Keyboard KBPC M
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
Pay particular attention to texts marked with this symbol. Failure to observe this warning
endangers your life, destroys the system, or may lead to loss of data.
!
This symbol is followed by supplementary information, remarks and tips.
i
Texts which follow this symbol describe activities that must be performed in the order shown.
"Quotation marks" indicate names of chapters, disks and terms that are being emphasized.
Important notes
In this chapter you will find information regarding safety which is essential to take note of
with your keyboard.
!
Safety
This device complies with the relevant safety regulations for data processing equipment, including
electronic office machines for use in an office environment. If you have any questions, contact your
sales office or our customer service.
• Transport the device only in its original packaging or another corresponding packaging to
protect it from knocks and jolts.
• If the device is brought into the installation site from a cold environment, condensation can
form. Before operating the device, wait until it is absolutely dry and has reached approximately
the same temperature as the installation site.
• During installation and before operating the device, observe the instructions on environmental
conditions in the chapter "Technical data
• Lay all cables so that nobody can stand on them or trip over them.
• Please ensure that no objects (e. g. necklaces, paperclips etc.) or liquids can get into the
interior of the device (short circuit).
• The device may only be operated on a low safety voltage (in accordance with IEC 950/
EN 60950).
• The keyboard interface of the system unit (5 V supply voltage) must have a safety fuse with a
maximum of 5 A.
• Data cables for peripherals must be adequately insulated to avoid interference.
• Use cleansing tissues to clean the outside of the keyboard.
Do not use any cleaning agents that contain abrasives or may corrode plastic.
• Keep this Operating Manual together with your device. If you pass on the device to third
parties, you should also pass on this manual.
".
2 - English
A26381-K276-Z100-3-5E19
Keyboard KBPC M
Manufacturer's note
CE certificate
The shipped version of this device complies with the requirements of the EEC
directive 89/336/EEC "Electromagnetic compatibility".
Disposal and recycling
This device has been manufactured to the greatest possible degree from materials which can be
recycled or disposed of in a manner that is not environmentally damaging. The device is taken back
after use, so that it can be recycled, provided that it is returned in a condition which is the result of
normal use. Any components not recuperated will be disposed of in an environmentally acceptable
manner.
If you have any questions on disposal, please contact your local office, our service department, or,
directly:
Siemens AG
Recycling Center
D-33106 Paderborn
Tel.: ++ 49 5251 - 818 010/ Fax: ++ 49 5251 - 818 015
FCC Class B Compliance Statement
If there is an FCC statement on the device, then:
The following statement applies to the products covered in this manual, unless otherwise specified
herein. The statement for other products will appear in the accompanying documentation.
NOTE:
This equipment has been tested and found to comply with the limits for a "Class B" digital device,
pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian InterferenceCausing Equipment Regulations. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in strict accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Siemens AG is not responsible for any radio or television interference caused by unauthorized
modifications of this equipment or the substitution or attachment of connecting cables and
equipment other than those specified by Siemens AG. The correction of interferences caused by
such unauthorized modification, substitution or attachment will be the responsibility of the user.
The use of shielded I/O cables is required when connecting this equipment to any and all optional
peripheral or host devices. Failure to do so may violate FCC rules.
A26381-K276-Z100-3-5E19
English - 3
Keyboard KBPC M
Connecting the keyboard
Please note the information provided in the chapter "Important notes" in the Operating
Manual of the PC or in the manual "Safety and Ergonomics".
!
Depending on what you have ordered, your delivery package will contain the following components:
• one keyboard KBPC M
• a telephone handset with support and telephone handset cable (optional)
• a headset with adapter (optional)
• a keyboard cable to connect to the PC
• this Operating Manual
Preparatory measures for using the telephone handset with support holder (if included in the
delivery package)
The support for the telephone handset can be locked into the left or right of the keyboard or used as
a standalone support.
If necessary, remove the support holder, turn it around and refit it.
Lock the support for the telephone handset into the keyboard or place it next to the keyboard.
Connect the handset cable to the handset.
Connections on the keyboard
The connection sockets are located on the underside of the keyboard:
5
4
3
2
1
1 = Socket for keyboard cable
2 = Mouse port
3 = Port for external microphone
The keyboard cable supplied has a 15-pin connector for connection to the keyboard and four round
connectors for connection to the system unit.
4 - English
4 = Stereo headphones port
5 = Socket for telephone handset/headset
A26381-K276-Z100-3-5E19
Loading...