Page 1
Monitor
Operating Manual
English
SCENICVIEW P20W-3/P22W-3
Page 2
Are there…
... any technical problems or other questions which you would like to be clarified?
Please contact
our help desk (see Warranty Booklet).
The latest information on our products, tips, updates, etc., can be found on the internet under:
http://www.fujitsu-siemens.com
Page 3
Page 4
This manual was produced by
Xerox Global Services
Published by
Fujitsu Siemens Computers GmbH
Order No.:
Edition
A26361-K1175-Z120-1-7619
1
AG 04/07
Page 5
SCENICVIEW
P20W-3/P22W-3
LCD monitor
Operating Manual
april 2007 edition
Page 6
VESA, DDC and DPMS are registered trademarks of Video Electronics Standards
Association.
Copyright © Fujitsu Siemens Computers GmbH 2007
All rights, including rights of translation, reproduction by printing, copying or similar methods,
in part or in whole, are reserved.
Offenders will be liable for damages.
All rights, including rights created by patent grant or registration of a utility model or design,
are reserved.
Delivery subject to availability. Right of technical modification reserved.
No liability for content and printing error.
Page 7
Contents
Introduction........................................................................................................................................... 1
Notational conventions ................................................................................................................. 2
Important notes..................................................................................................................................... 2
Safety notes.................................................................................................................................. 2
Power cable.................................................................................................................................. 4
Transport ...................................................................................................................................... 4
Cleaning ....................................................................................................................................... 4
CE marking................................................................................................................................... 4
FCC Class B Compliance Statement ........................................................................................... 5
Declaration of Conformity............................................................................................................. 5
Energy Star Guidelines................................................................................................................. 6
Disposal and recycling ................................................................................................................. 6
Checking the contents of the consignment........................................................................................... 7
Installing an ergonomic video workstation............................................................................................ 8
Mounting and removing the monitor base ............................................................................................ 9
Mounting the monitor base........................................................................................................... 9
Removing monitor base ............................................................................................................. 10
Connecting the monitor .............................................................................................................. 10
Connecting cables to the monitor............................................................................................... 11
Connecting cables to the computer............................................................................................ 12
Operation of the monitor..................................................................................................................... 12
Adjustment of height and inclination........................................................................................... 12
Switching the monitor on/off ....................................................................................................... 13
Notes on power management .................................................................................................... 14
Changing the monitor settings.................................................................................................... 15
Notes on ergonomic colour adjustment.............................................................................................. 21
Troubleshooting.................................................................................................................................. 22
Notes regarding the DIN EN ISO 13406-2 standard .......................................................................... 24
Technical data .................................................................................................................................... 25
VESA-DDC-compatible VGA interface....................................................................................... 26
Preset operating modes ............................................................................................................. 26
Pin assignment D-SUB............................................................................................................... 27
Monitor port DVI-D...................................................................................................................... 27
HDMI monitor connections ......................................................................................................... 28
A26361-K1175-Z120-1-7619, edition 1
Page 8
Contents
A26361-K1175-Z120-1-7619, edition 1
Page 9
Introduction
Your new LCD (Liquid Crystal Display) monitor SCENICVIEW P20W-3/P22W-3 offers numerous
features and functions, for example:
● TFT display (Thin Film Transistor; active matrix)
● minimal space requirements thanks to slim casing
● optimum ergonomic characteristics (totally distortion-free, excellent picture definition and colour
purity right into the corners)
● high degree of brightness and good contrast
● high resolution (1680 x 1050)
● presentation of up to 16.7 million colours (in conjunction with an appropriate graphics card)
● automatic scanning of horizontal frequencies from 30 to 82 kHz and refresh rates (vertical
frequencies) from 56 to 76 Hz (absolutely flicker-free)
● digital screen controller with microprocessor for storing 28 different display modes
● freely adjustable colour alignment for matching the screen colours to the colours of various
input and output devices
● convenient operation via integrated OSD (On-Screen-display) menu
● VESA-DDC compatibility
● VESA-FPMPMI compatibility (Flat Panel Monitor Physical Mounting Interface) – Mounting
device for swivel arm and wall bracket
● plug&play capability
● digital video inputs (DVI and HDMI) with HDCP
● power management for reducing power consumption when the computer is not in use
● compliance with the recommendations in accordance with TCO’03
● The monitor fulfils all GS (“Geprüfte Sicherheit”, Certified Security) requirements.
This operating manual contains important information you require to start up and run your LCD
monitor.
A graphics card (screen controller) with VGA interface or a digital graphics card with DVI interface or
video signal source with HDMI interface is required to control the SCENICVIEW P20W-3/P22W-3.
The monitor processes the data supplied to it by the screen controller. The screen controller or the
associated driver software is responsible for setting the modes (resolution and refresh rate).
When putting the monitor into operation for the first time, the screen display should be optimally
adapted to the screen controller used and adjusted in accordance with your needs (see the
"
Changing the monitor settings" section in the "Operation of the monitor" chapter).
Target group
You don't need to be an "expert" to perform the operations described here. However, please observe
the safety information given in the operating instructions of the computer and in this manual.
In the event of any problems occurring, please contact your sales outlet or our help desk.
Additional information
Details of how you set the resolution and refresh rate are provided in the documentation on your
screen controller/the associated driver software.
For ergonomic reasons, we recommend a screen resolution of 1680 x 1050 when using the
SCENICVIEW P20W-3 and P22W-3 monitors.
Because of the technology used (active matrix) an LCD monitor provides a totally flicker-free picture
even with a refresh rate of 60 Hz.
A26361-K1175-Z120-1-7619, edition 1 1
Page 10
SCENICVIEW P20W-3/P22W-3
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
Pay particular attention to text marked with this symbol. Failure to observe this warning
!
endangers your life, destroys the device, or may lead to loss of data.
i
► Text which follows this symbol describes activities that must be performed in the order shown.
"Quotation marks" indicate names of chapters or terms.
This font indicates filenames and menu items.
This font indicates screen outputs.
Supplementary information, remarks, and tips follow this symbol.
Important notes
In this chapter you will find information regarding safety which is essential to take note of
!
Safety notes
This device complies with the relevant safety regulations for data processing equipment, including
electronic office machines for use in an office environment. If you have any questions, contact your
sales outlet or our help desk.
● The display surface of the LCD monitor is sensitive to pressure and scratches. You should
with your monitor.
therefore be careful with the display surface so as to avoid lasting damage (scratches).
● If the device is brought into the installation site from a cold environment, condensation can
form. Before operating the device, wait until it is absolutely dry and has reached approximately
the same temperature as the installation site.
● During installing and operating the device, please observe the instructions on environmental
conditions in the "
ergonomic video workstation
2 A26361-K1175-Z120-1-7619, edition 1
Technical data" chapter as well as the instructions in the "Installing an
" chapter.
Page 11
SCENICVIEW P20W-3/P22W-3
● To ensure sufficient ventilation, the intake and exhaust air openings of the monitor must never
be blocked.
● The monitor automatically sets itself to a mains voltage in the range of 100 V to 240 V. Ensure
that the local mains voltage lies within these limits.
● Ensure that the power socket on the device or the grounded mains outlet is freely accessible.
● The ON/OFF switch does not disconnect the device from the mains voltage. To completely
disconnect the mains voltage, remove the power plug from the socket.
● The monitor is equipped with a power cable that complies with safety standards.
● Lay all cables so that nobody can stand on them or trip over them. When attaching the device,
observe the relevant notes in the "
● No data transfer cables should be connected or disconnected during a thunderstorm.
● Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get inside the
device (danger of electric shock, short circuit).
● The device is not waterproof! Never immerse the device in water and protect it from spray
water (rain, sea water).
● In emergencies (e.g. damaged casing, elements or cables, penetration of liquids or foreign
matter), switch off the unit, disconnect the power plug and contact your sales outlet or our help
desk.
Connecting the monitor" chapter.
● The monitor must be disposed of in accordance with the local regulations for disposal of
special waste. The screen background lighting contains mercury. You must observe the
applicable handling and disposal safety regulations for fluorescent tubes.
● Only qualified technicians should repair the device. Unauthorised opening and incorrect repair
may greatly endanger the user (electric shock, fire risk).
● You may set only those resolutions and refresh rates specified in the "
Technical data" chapter.
Otherwise you may damage your monitor. If you are in any doubt, contact your sales outlet or
our help desk.
● Use a screen saver with moving images and activate the power management for your monitor
to prevent still images from "burning in".
● If you operate the monitor with the swivel arm or wall bracket, it may not be turned by 180°.
● The SCENICVIEW P20W-3/P22W-3 screen must only be operated in 0° landscape mode. The
buttons of the control panel are located at the bottom in the middle of the monitor.
● Store this manual close to the device. If you pass the device on to third parties, you should
pass this manual on with it.
A26361-K1175-Z120-1-7619, edition 1 3
Page 12
SCENICVIEW P20W-3/P22W-3
Power cable
To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary to
replace the original cable set.
● The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.
● The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the
outer sheath.
● For devices which are mounted on a desk or table, type SVT or SJT cable sets may be used.
For devices which sit on the floor, only SJT type cable sets may be used.
● The cable set must be selected according to the rated current for your device.
● If necessary, replace the original power cable with a regular grounded 3-core mains lead.
Transport
● Transport the monitor with care and only in its original packaging or another corresponding
packaging fit to protect it against knocks and jolts.
● Never drop the LCD monitor (danger of glass breakage).
Cleaning
● Always pull out the power plug before you clean the monitor.
● Do not clean any interior parts yourself, leave this job to a service technician.
● Do not use any cleaning agents that contain abrasives or may corrode plastic.
● Ensure that no liquid will run into the system.
● Ensure that the ventilation areas of the monitor are free.
● The display surface of the LCD monitor is sensitive to pressure and scratches. Clean it only
using a soft, slightly moistened cloth.
Wipe the monitor casing with a dry cloth. If the monitor is particularly dirty, use a cloth which has
been moistened in mild domestic detergent and then carefully wrung out.
CE marking
The shipped version of this device complies with the requirements of the EU directives
2004/108/EU "Electromagnetic compatibility" and 2006/95/EU "Low voltage directive".
4 A26361-K1175-Z120-1-7619, edition 1
Page 13
SCENICVIEW P20W-3/P22W-3
FCC Class B Compliance Statement
The following statement applies to the products covered in this manual, unless otherwise specified
herein. The statement for other products will appear in the accompanying documentation.
NOTE:
This equipment has been tested and found to comply with the limits for a "Class B" digital device,
pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian InterferenceCausing Equipment Standard ICES-003 for digital apparatus. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in strict
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between equipment and the receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
● Consult the dealer or an experienced radio/TV technician for help.
Fujitsu Siemens Computers GmbH is not responsible for any radio or television interference caused
by unauthorised modifications of this equipment or the substitution or attachment of connecting
cables and equipment other than those specified by Fujitsu Siemens Computers GmbH. The
correction of interferences caused by such unauthorised modification, substitution or attachment will
be the responsibility of the user.
The use of shielded I/O cables is required when connecting this equipment to any and all optional
peripheral or host devices. Failure to do so may violate FCC and ICES rules.
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Product name: Colour LCD Monitor
Trade name: Fujitsu Siemens Computers Inc.
Model number(s): SCENICVIEW P20W-3/P22W-3
Name of responsible party: Fujitsu Siemens Computers Inc.
1250E. Arques Avenue
Sunnyvale, CA 94085
U.S.A.
Contact person: Schroettle-Henning, Bernd
Phone No.: (408) 834-0306
Fax No.: (408) 746-8299
We, Fujitsu Siemens Computers Inc., hereby declare that the equipment bearing the trade name and
model number specified above was tested confirming to the applicable FCC Rules under the most
accurate measurement standards possible, and that all the necessary steps have been taken and
are in force to assure that production units of the same equipment will continue to comply with the
Commissions requirements.
A26361-K1175-Z120-1-7619, edition 1 5
Page 14
SCENICVIEW P20W-3/P22W-3
Energy Star Guidelines
The Fujitsu Siemens LCD colour monitor SCENICVIEW P20W-3/P22W-3
is equipped with a power management system which reduces the power
draw in OFF mode to less than 1 W. With this new power management the
LCD monitor SCENICVIEW P20W-3/P22W-3 satisfies the requirements for
the U.S. Environmental Protection Agency's (EPA) Energy Star Computers
award.
The EPA estimates that computer equipment uses 5 % percent of all business electricity and that
this is growing rapidly. If all desktop computers and peripherals enter a low-power mode when not in
use, the overall savings in electricity could amount to $ 2 thousand million annually. These savings
could also prevent the emission of 20 million tons of carbon dioxide into the atmosphere - the
equivalent of 5 million automobiles.
As an Energy Star Partner, Fujitsu Siemens Computers GmbH has determined that this product
meets the Energy Star guidelines for energy efficiency.
Disposal and recycling
This device has been manufactured to the highest possible degree from materials which can be
recycled or disposed of in a manner that is not environmentally damaging. The device may be taken
back after use to be recycled, provided that it is returned in a condition that is the result of normal
use. Any components not reclaimed will be disposed of in an environmentally acceptable manner.
If you have any questions on disposal, please contact your local office, our help desk, or:
Germany Belgium Switzerland
Fujitsu Siemens Computers
GmbH
Remarketing und Recycling
D-33106 Paderborn
Tel.: +49 5251 / 81 80 10
Fax: +49 5251 / 81 80 15
http://www.fujitsu-siemens.de/wvm
Asia USA
Taiwan: Environmental
Protection Administration
Executive Yuan R.O.C.
http://recycle.epa.gov.tw/
RECUPEL
Boulevard Reyers, 80
B-1030 Brussels
Tel.: +32 2 / 706 86 16
Fax: +32 2 / 706 86 13
E-Mail: info@recupel.be
http://www.recupel.be
Fujitsu Siemens
Computers Inc.
1250E. Arques Avenue
Sunnyvale, CA 94085 U.S.A.
Contact: Schroettle-Henning,
Bernd
Phone No.: (408) 834-0306
Fax No.: (408) 746-8299
SWICO
Schweizerischer
Wirtschaftsverband der
Informations-,
Kommunikations- und
Organisationstechnik
A list of the SWICO
Acceptance places can be
found at:
http://www.swico.ch
You can find more information on the Internet at
6 A26361-K1175-Z120-1-7619, edition 1
www.fujitsu-siemens.com/recycling.
Page 15
SCENICVIEW P20W-3/P22W-3
Checking the contents of the consignment
The display surface of the LCD monitor is sensitive to pressure and scratches. Always
!
► Unpack all the individual parts.
► Check the delivery for damage incurred during transportation.
► Check whether the delivery agrees with the details in the delivery note.
hold the device by the casing!
The complete LCD monitor package includes:
– one monitor
– one data cable (D-SUB)
– one data cable (DVI-D)
– one data cable (HDMI)
– one audio cable
– one power cable
– one CD with software and documentation
– one Warranty Booklet
– one "Quick Start Guide" brochure
– one "Safety" manual
Should you discover that the delivery does not correspond to the delivery note, notify your local sales
outlet immediately.
We recommend that you keep the original packaging material. Keep it for future
i
transportation.
A26361-K1175-Z120-1-7619, edition 1 7
Page 16
SCENICVIEW P20W-3/P22W-3
Installing an ergonomic video workstation
2
1
1
1 = Windows
Avoid direct and reflected glare.
1 = Bearing surface for palms
of hands
2 = Reaching area for
frequently used equipment
Position the monitor for
optimum viewing. The viewing
distance to the monitor should
be approximately 50 cm.
Avoid glare from electric
lighting.
Example layout of monitor,
keyboard and copy-holder
1 = Edge of desk
2 = Permissible reaching
sector
Position the keyboard where it
is easiest to reach.
0°
60°
1 = Preferred viewing distance
2 = Permissible viewing
distance
Position the monitor for
optimum viewing. The viewing
distance to the monitor should
be approximately 50 cm.
1
65°
30°
30°
65°
22
Depending on the situation, the use of a swivel arm or wall bracket (VESA FPMPMI), are available
from specialised dealers, may be advisable. For this purpose the monitor base must be removed
beforehand as described in the "
8 A26361-K1175-Z120-1-7619, edition 1
Keep ventilated areas clear.
i
Mounting and removing the monitor base" chapter.
Page 17
SCENICVIEW P20W-3/P22W-3
Mounting and removing the monitor base
The display surface is susceptible to scratching! Therefore, lay the monitor on a soft
!
Mounting the monitor base
surface when mounting or removing the monitor base.
1. Guide the lug on the front of the foot into the base plate (1).
2. Firmly press the base plate on at the rear (2).
3. Secure the base plate with the screw (3).
A26361-K1175-Z120-1-7619, edition 1 9
Page 18
SCENICVIEW P20W-3/P22W-3
Removing monitor base
Before you can use a swivel arm or a wall bracket, you must remove the monitor base:
!
► Switch off the monitor and pull the power plug out of the power socket.
► Lay the monitor on its face on a soft surface.
► Remove the cover and disconnect all cables.
The display surface is susceptible to scratching!
► Remove the four screws on the rear of the
monitor.
You can now mount a swivel arm or a wall
bracket as per VESA FPMPMI with 100 mm hole
spacing.
For instructions on how to mount the swivel arm
or wall bracket, please see the documentation for
the swivel arm or wall bracket.
If you operate the monitor with the swivel arm or wall bracket, it may not be turned by 180°.
!
Connecting the monitor
Please take note of the safety information in the "Important notes" chapter.
!
► Be sure that the monitor and the computer are switched off.
10 A26361-K1175-Z120-1-7619, edition 1
CE conformance and optimum picture quality are guaranteed only if you use the data
cables supplied.
Do not cover the ventilation openings of the monitor.
The computer power plug must be pulled out!
Page 19
SCENICVIEW P20W-3/P22W-3
Connecting cables to the monitor
The monitor ports are protected by a cover.
► Remove the cover.
1 = Main switch
2 = Power socket
3 = HDMI socket
4 = DVI-D socket (DIGITAL)
5 = D-SUB socket (VGA)
6 = AUDIO-IN socket
7 = Security slot for "Kensington Lock"
8 = Space for the cover
9 = Holes for fixing swivel arm or wall bracket
The data cables supplied have two 15-pin D-SUB connectors / two 24-pin DVI connectors for
connection to the monitor and to the computer.
► Select the suitable data cable for your computer.
Information on the computer connections and interfaces is contained in the operating manual
for your computer.
► Connect one of the connectors of the data cable to the D-SUB socket (5) or the DVI-D socket
(4) or to the HDMI socket (3) on the monitor and secure the plug connection by tightening the
retaining screws.
The monitor automatically detects the input when only one signal source is connected.
i
► Insert one connector of the audio line in the AUDIO IN (7) socket on the monitor and make sure
it is properly engaged.
► Plug the power cable supplied into the power socket (2) of the monitor.
► Mount the cover over the connections.
A Kensington lock can be mounted in the security slot (6) to prevent the monitor from
i
being stolen. A Kensington lock is not included on delivery of the monitor.
A26361-K1175-Z120-1-7619, edition 1 11
Page 20
SCENICVIEW P20W-3/P22W-3
Connecting cables to the computer
Information on the computer connections and interfaces is contained in the operating manual for your
computer.
i
► Connect the data cable to the (active) monitor port on the computer and secure the plug-in
► Insert the other plug of the audio line in the audio output of the computer.
► Plug the connector of the mains cable provided into the monitor outlet of the computer or into a
► Plug the power connector of the computer into a properly grounded mains outlet.
i
If your computer has two monitor ports ("onboard" screen controller and separate
graphics card), the monitor port for the separate graphics card is usually active.
connection by tightening the safety screws.
properly earthed outlet and ensure a safe connection.
When you start working with your monitor for the first time you should install the
appropriate graphics drivers for your application software. Details of how to do this are
provided in the documentation on your screen controller/the associated driver software.
Operation of the monitor
The monitor offers the following possibilities that enable it to be optimally adjusted for the respective
user and the respective situation.
Adjustment of height and inclination
The height of the monitor can be adjusted by approximately 120 mm
► Grasp the monitor with both hands at the left and right edges of the housing and move it up or
down.
The inclination of the monitor can be adjusted by -5° (forward) and +25° (backwards) from its vertical
position.
► Hold the monitor with both hands on the left and right sides of the housing and move it to the
desired angle.
12 A26361-K1175-Z120-1-7619, edition 1
Page 21
SCENICVIEW P20W-3/P22W-3
Switching the monitor on/off
The main switch at the rear and the ON/OFF switch at the front are used for switching the monitor on
and off.
► To start, switch the monitor on with the main switch (4) at the rear.
1 = Buttons for the OSD menu
(On-Screen-display)
2 = Power indicator
3 = ON/OFF switch
4 = Main switch
Press the buttons from the bottom up.
i
The power indicator (3) lights up blue when the monitor and computer are switched on. The power
indicator lights up orange if the monitor is not receiving a video signal or if it is in energy saving
mode. The power indicator goes out when the monitor is switched off.
When you switch the computer system on, you must proceed in the following order:
► Switch the LCD monitor on with the ON/OFF switch (2).
► Then switch on the computer.
If your computer has a power management function (energy-saving mode), you should
i
read the "
Notes on power management" section in this chapter.
A26361-K1175-Z120-1-7619, edition 1 13
Page 22
SCENICVIEW P20W-3/P22W-3
Notes on power management
If your computer is equipped with power management, the monitor can support this function fully.
Here the monitor does not distinguish between the individual energy-saving modes of the computer
(standby mode, suspend mode and OFF mode), as it is capable of immediately switching into the
mode with the highest energy-saving effect.
Stage ON Power-Saving Mode
Power indicator lights up blue lights up orange
Function the monitor is working
normally
Power consumption P20W-3: 42 W typical
P22W-3: 49 W typical
If your computer detects inactivity (no input) it sends an appropriate signal to the monitor to reduce
the power consumption (energy-saving mode). The power indicator of the monitor changes colour to
indicate the status change.
Once an input is made at the computer the screen contents are redrawn and full power is restored.
For detailed information on how energy-saving mode operates refer to the operating manual or
technical manual of the computer.
When the monitor is switched to the energy-saving mode by the power management
i
system a power consumption of up to 1 W is maintained to feed the circuit for redrawing
the screen contents.
To completely switch off the power consumption, switch off the monitor with the main
switch at the rear.
the screen is dark
reduced to < 1 W
14 A26361-K1175-Z120-1-7619, edition 1
Page 23
SCENICVIEW P20W-3/P22W-3
Changing the monitor settings
When putting the monitor into operation for the first time, the screen display should be optimally
adapted to the screen controller used and adjusted in accordance with your needs.
Choosing basic monitor settings using the supplied software
If one of the operating systems Windows 95/98, Windows NT, Windows Me, Windows 2000,
Windows XP or OS/2 (with Windows emulation installed) is used, the basic monitor settings can be
set with the CD supplied.
► Insert the supplied CD into the CD-ROM drive.
► Open the
Your monitor should now already be properly adjusted. If none of the above operating systems is
used or minor corrections are to be made to the screen display, then change the monitor settings
with the OSD menu.
Readme file on the CD and follow the instructions in the file.
Changing the monitor settings with the buttons of the control panel
1 = Buttons for the OSD menu
(On-Screen-display)
Use the buttons of the control panel to change the following monitor settings directly while the OSD
menu is switched off.
Performing auto-adjustment of the monitor
► Press the AUTO button for approx. 1 second while the OSD menu is switched off
Auto Processing message is displayed.
The
2 = Power indicator
3 = ON/OFF switch
Picture quality and position are set to optimum values for your system.
Selecting input signal (D-SUB/DVI-D)
► Press the INPUT button for calling the Input select setting window.
► Press the
This setting window can also be called up when the OSD menu is locked.
Activating/deactivating muting
► Press the button to switch the sound off and on again.
A message is displayed that the action has been performed.
A26361-K1175-Z120-1-7619, edition 1 15
or 5 button to select the desired monitor connection (VGA, DVI or HDMI).
6
Page 24
SCENICVIEW P20W-3/P22W-3
Locking the OSD menu
The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings.
► Press and hold the SELECT/MENU button for a few seconds while you switch on the monitor
with the ON/OFF switch.
A message is displayed that the action has been performed.
Please proceed in the same manner to release the locked OSD menu again.
Locking the ON/OFF button
The ON/OFF switch can be locked to prevent accidental or unauthorised changes to the monitor
settings.
► Press and hold both buttons
A message is displayed that the action has been performed.
Please proceed in the same manner to release the locked ON/OFF switch again.
and 5 simultaneously for a few seconds.
6
Monitor settings using the OSD menu
With the buttons on the control panel, call up and use the integrated OSD (On-Screen display) menu.
The OSD menu is available in different languages. The English menu names are used in
i
To set the OSD menu, perform the following steps:
► Press the SELECT/MENU button to activate the OSD menu.
The main menu appears on the screen (on the left-hand side) with icons for the setting functions.
the following description (default setting). With the OSD function
you can select another language.
The first symbol (
highlighted. In the right-hand part of the display
the associated functions are shown.
► If necessary, press the
mark another icon (e.g.
► Press the SELECT/MENU button to select
the highlighted icon.
Language in the OSD Setup
Brightness/Contrast) is
or 5 button to
6
Image adjust).
16 A26361-K1175-Z120-1-7619, edition 1
Page 25
SCENICVIEW P20W-3/P22W-3
The corresponding setting window (here: Image Adjust) is displayed (on the right-hand side).
The first function (
► If necessary, press the
mark another function.
► Press the SELECT/MENU button to select
the highlighted function.
► Press the
value for the selected function.
► Press the EXIT/AUTO button to exit the
function.
► If necessary, press the button
mark another function or press the
EXIT/AUTO button to return to the main
menu.
All changes are stored automatically.
If you want to change other settings, select the corresponding function from the OSD main menu. All
possible adjustments of the main menu are described in the following.
The OSD menu for analogue monitor operation is described in the following. During digital
i
operation some functions are not available, as they are not required due to the digital
transmission technology used.
Phase) is highlighted.
or 5 button to
6
or 5 button to adjust the
6
6
or 5 to
Adjusting the brightness and contrast
Brightness
Contrast
Black level
Auto brightness
Auto level
Calls up the
Setting the brightness of the display
This function is used to change the brightness of the background lighting.
Setting the contrast of the display
This function is used to modify the contrast of bright colour tones.
Setting the brightness of the display
This function is used to can modify the contrast of dark colour tones.
Automatic brightness control
This function is used to automatically control the brightness of the background
lighting using the light sensor.
On = The brightness is adjusted according to the ambient brightness
Off = The brightness is adjusted manually by the user.
Adjusting the signal level
This function is used to automatically adjust the contrast.
Press the SELECT/MENU button to activate the function.
Brightness / Contrast setting window
A26361-K1175-Z120-1-7619, edition 1 17
Page 26
SCENICVIEW P20W-3/P22W-3
If the contrast is set too high, bright surfaces can no longer be distinguished from very
i
Selecting the application mode
bright surfaces. If the contrast is set too low, the maximum brightness will not be achieved.
Office
Photo
Video
Adjusting the screen size and position
Phase
Clock
H-position
Calls up the
Office presets (the settings for colour and sharpness can be adjusted)
Photo presets (colour, sharpness, saturation)
Video presets (colour, sharpness, saturation)
Calls up the
Eliminating picture interference
This function is used to fine-tune your monitor in order to eliminate picture
interference.
Adjusting the synchronisation settings
This function is used to adjust the picture width in order to eliminate vertical picture
interference.
Adjustment of the horizontal position
This function is used to move the picture to the left or to the right.
Mode setting window
Image adjust setting window
V-position
Sharpness
Saturation
Expansion
Adjusting the vertical position
This function is used to move the picture up or down.
Adjusting the sharpness of the picture for the photo and video modes.
Adjusting the colour saturation for the photo and video modes.
Adjusting the screen size
Full screen = selection of full-screen mode.
Keep aspect = maximum picture size without distortion of the ratio. (Only for PC
picture)
16:9 = 16:9 Widescreen format (video/TV picture only)
4:3 = 4:3 format (video/TV picture only)
18 A26361-K1175-Z120-1-7619, edition 1
Page 27
SCENICVIEW P20W-3/P22W-3
Adjusting the volume
Calls up the
Audio setting window
Volume
Mute
Setting the volume for playback with the integrated loudspeakers
Switching the loudspeakers off or on
Setting the colour temperature and colours
Calls up the
Colour setting window
Select the colour temperature
The "warmth" of the screen colours is set using the colour temperature. The colour
temperature is measured in Kelvin (K). You can select from
and Custom Colour.
Native
sRGB
Native
Custom Colour
The options
= Colour display according to the sRGB standard
= Original colour of the LCD display
= User defined colours
sRGB, Native and Custom colour are only available in the setting mode
Office.
In the user-defined setting you can change the colour ratios of the basic colours
(red, green, blue) as required.
sRGB, 6500 K, 9300 K,
A26361-K1175-Z120-1-7619, edition 1 19
Page 28
SCENICVIEW P20W-3/P22W-3
Settings functions
Input select
Language
DDC-CI
OSDH-position
OSDV-position
OSDTimeout
Calls up the
Setup settings window
Selecting the input signal
This function is used to select the input signal (VGA, DVI or HDMI).The condition is
that the graphic card used supports this function.
Setting the language for the OSD menu
This function is used to choose between English (default setting), French, German,
Italian, Spanish, Russian, Dutch or Swedish as the language for the OSD menu.
Activation/deactivation of the DDC-CI
On = the DDC-CI function is activated (standard setting).
Off = the DDC-CI function is deactivated.
Setting the horizontal position of the OSD menu
This function is used to move the OSD menu to the left or to the right.
Setting the vertical position of the OSD menu
This function is used to move the OSD menu up or down.
Setting the display duration of the OSD menu
With this function you select a value from 10 to 120 seconds.
If the set time expires without a setting being made, the OSD menu is automatically
faded out.
Factory recall
Activating the factory settings
With this function all settings are reset to the factory settings without prompting for
confirmation.
Press the SELECT/MENU button to activate the function. The
message is displayed.
Displaying information
Calling the
With this function the model designation, serial number, resolution, H/V frequency,
input signal and polarity of the synchronisation signal are displayed.
Auto Processing
Information setting window
20 A26361-K1175-Z120-1-7619, edition 1
Page 29
SCENICVIEW P20W-3/P22W-3
Notes on ergonomic colour adjustment
If you select colours for the display in your application programmes, take note of the information
below.
The primary colours blue and red on a dark background do not produce the minimum required
contrast of 3:1 and are therefore not suitable for continuous text and data entry.
When using several colours for characters and background and giving the primary colours full
modulation, you can obtain very suitable colour combinations (see the following table):
Background
black white purple blue cyan green yellow red
black + + - + + + -
white + + + - - - +
purple + + - - - - -
blue - + - + - + -
cyan + - - + - - -
green + - - + - - -
yellow + - + + - - +
red - + - - - - +
+ Colour combination very suitable
- Colour combination not suitable because colour locations are too close together, thin characters
are not identifiable or rigorous focusing is demanded of the human eye.
Characters
A26361-K1175-Z120-1-7619, edition 1 21
Page 30
SCENICVIEW P20W-3/P22W-3
Troubleshooting
Should an error occur, first check the following points. If the distortion is still not eliminated, the
monitor should, if possible, be checked on another computer.
If you are unable to solve the problem, please inform our help desk.
Having this problem? Check the following points:
No screen display
(power indicator does not light)
No screen display
(power indicator lights)
Message:
No Signal
Message:
Frequency out of range:
## kHz / ## Hz
► Check whether the main switch at the rear of the
monitor is switched on.
► Check whether the power cable on the monitor is
connected correctly.
► Check whether the computer is switched on.
► Check whether the computer is switched on.
► Check whether the data cable for the monitor is
correctly attached to the monitor port on the
computer.
► Press any key on the computer keyboard - the
computer may be in energy saving mode.
► Alter the brightness and/or contrast until you get a
picture.
► Check whether the data cable for the monitor is
correctly attached to the monitor port on the
computer.
► Check whether the computer is switched on.
The input signal (horizontal frequency and refresh rate)
at the displayed input does not correspond to the
technical monitor data.
Please change the display mode to
1680 x 1050 with 60 Hz
Picture position not correct The monitor recognises an undefined mode (see the
Picture is shaking ► Check whether the data cable for the monitor is
► Adjust the video frequency range using the
computer software (see documentation for your
computer or your graphics card).
► Adjust a different screen resolution using the
computer software (see documentation for your
computer or your screen controller).
Technical data" chapter).
"
► Press the EXIT/AUTO button to perform the auto-
adjustment of the screen.
correctly attached to the monitor port on the
computer.
► Press the EXIT/AUTO button to perform the auto-
adjustment of the screen.
22 A26361-K1175-Z120-1-7619, edition 1
Page 31
SCENICVIEW P20W-3/P22W-3
Having this problem? Check the following points:
Picture is wrongly adjusted ► Press the SELECT/MENU button to activate the
Factory Recall. The Auto Processing
Picture disturbances (vertical lines)
Picture disturbances (horizontal lines,
picture noise)
function
message is displayed.
► Press the EXIT/AUTO button to perform the auto-
adjustment of the screen.
► Press the EXIT/AUTO button to perform the auto-
adjustment of the screen.
The screen becomes darker
The background lighting has a limited lifetime. If your
monitor display should become too dark, the
background lighting will have to be exchanged.
► Please contact our help desk.
A26361-K1175-Z120-1-7619, edition 1 23
Page 32
SCENICVIEW P20W-3/P22W-3
Notes regarding the DIN EN ISO 13406-2 standard
Permanently unlit or lit pixels
The standard of production techniques today cannot guarantee an absolutely fault-free screen
display. A few isolated constant lit or unlit pixels (picture elements) may be present. The maximum
permitted number of pixels faults is stipulated in the stringent international standard ISO 13406-2
(Class II).
Examples:
A 20" or 22" flat-screen monitor with a resolution of 1680 x 1050 has 1680 x 1050 = 1764000 pixels.
Each pixel consists of three subpixel (red, green and blue), so there are almost 5.3 million subpixel in
total. In accordance with ISO 13406-2 (Class II), a maximum of 6 pixels and 9 subpixel may be
defective.
Pixel A pixel consists of 3 subpixel, normally red, green and blue. A pixel is
the smallest element that can be generated by complete functionality
of the display.
Subpixel A subpixel is a separately addressable internal structure within a pixel
that enhances the pixel function.
Cluster A cluster contains two or more defective pixels or subpixel in a 5 x 5
pixel block.
24 A26361-K1175-Z120-1-7619, edition 1
Page 33
SCENICVIEW P20W-3/P22W-3
Technical data
P20W-3 P22W-3
Dimensions and weight
Visible diagonals: 51 cm 56 cm
Dot pitch: 0.258 mm 0.282 mm
Screen size: Width:
Height:
433.4 mm
270.9 mm
473.8 mm
296.1 mm
Maximum resolution: 1680 x 1050 1680 x 1050
Dimensions incl.
monitor base:
Dimensions of
box:
Width:
Height:
Depth:
Width:
Height:
Depth:
476 mm
360 mm
226 mm
561 mm
265 mm
438 mm
510 mm
371 mm
226 mm
616 mm
484 mm
250 mm
Weight (without packaging): approx. 7.0 kg approx. 7.4 kg
Storable display modes: 25 25
Pixel error classes according to
Class II Class II
ISO 13406-2:
Accessories: Power cable (1.8 m)
D-SUB data cable (1.8 m)
DVI-D data cable (1.8 m)
HDMI data cable (1.8 m)
Audio cable (1.8 m)
Electrical parameters
Video: Analogue, positive, 0.7 Vpp, 75 Ω
Digital: DVI-D / HDMI with HDCP
Synchronisation: Separate Sync. TTL, positive or negative
Horizontal frequency: 28 kHz .... 80 kHz (multi-scanning)
Refresh rate: 50 Hz .... 75 Hz
Maximum pixel rate: 165 MHz
Power supply: Switches automatically
100 V - 240 V, 50 Hz - 60 Hz
Power consumption (typical):
(without audio)
P20W-3: 42 W
P22W-3: 49 W
< 1 W in energy-saving mode
Sound output: 2.0 W left; 2.0 W right
A26361-K1175-Z120-1-7619, edition 1 25
Page 34
SCENICVIEW P20W-3/P22W-3
Environmental conditions
Environment class 3K2, IEC 721
Rated range of operation:
Humidity:
Limit range of operation:
Humidity:
Condensation must be avoided.
15 °C .... 35 °C
20 % .... 85 %
5 °C .... 35 °C
20 % .... 85 %
VESA-DDC-compatible VGA interface
Your monitor is equipped with a VESA-DDC-compatible VGA interface. VESA-DDC (Video
Electronics Standard Association, Display Data Channel) is used as the communications interface
between the monitor and the computer. If your computer is equipped with a VESA-DDC-compatible
VGA interface, it can automatically read the data for ensuring optimum operation from your monitor
and select the appropriate settings.
If the monitor SCENICVIEW P20W-3/P22W-3 is not yet displayed in the list of monitors,
i
you can select the following monitor instead:
Fujitsu Siemens P17-2, P19-2, B17-2, B19-2
Preset operating modes
The picture position and size have been set to optimum values at the factory for the
i
The following are the most frequently used of the preset operating modes:
operating modes listed above. Depending on the screen controller used, it may be
necessary to adjust the display position and size. In this case, you can change and save
the settings (see "
Operation of the monitor").
Horizontal frequency Refresh rate Screen resolution
31.5 kHz
31.5 kHz
37.5 kHz
37.9 kHz
46.9 kHz
48.4 kHz
60.0 kHz
64.0 kHz
For ergonomic reasons, a screen resolution of 1680 x 1050 pixels is recommended. Due to the
technology used (active matrix), an LCD monitor provides a totally flicker-free picture even with a
refresh rate of 60 Hz.
26 A26361-K1175-Z120-1-7619, edition 1
70 Hz
60 Hz
75 Hz
60 Hz
75 Hz
60 Hz
75 Hz
60 Hz
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1680 x 1050
Page 35
SCENICVIEW P20W-3/P22W-3
Pin assignment D-SUB
1
5
6
10
11
15
Pin Meaning Pin Meaning
1 Video input red 9 +5 V (DDC)
2 Video input green 10 Sync. earth
3 Video input blue 11 Earth
4 Earth 12 DDC-Data
5 Earth 13 H. sync
6 Red video earth 14 V. sync
7 Green video earth 15 DDC Clock
8 Blue video earth
Monitor port DVI-D
1
9
17
Pin Meaning Pin Meaning Pin Meaning
1 TMDS Data2- 9 TMDS Data1- 17 TMDS Data0-
2 TMDS Data2+ 10 TMDS Data1+ 18 TMDS Data0+
3 TMDS Data 2/4 Shield 11 TMDS Data 1/3 Shield 19 TMDS Data 0/5 Shield
4 not connected 12 not connected 20 not connected
5 not connected 13 not connected 21 not connected
6 DDC Clock 14 +5V Power 22 TMDS Clock Shield
7 DDC Data 15 Earth 23 TMDS Clock+
8 Analogue Vertical Sync 16 Hot Plug Detect 24 TMDS Clock-
A26361-K1175-Z120-1-7619, edition 1 27
Page 36
SCENICVIEW P20W-3/P22W-3
HDMI monitor connections
Pin Meaning Pin Meaning
1 TMDS Data2+ 2 TMDS Data2 Shield
3 TMDS Data2- 4 TMDS Data1+
5 TMDS Data1 Shield 6 TMDS Data1-
7 TMDS Data0+ 8 TMDS Data0 Shield
9 TMDS Data0- 10 TMDS Clock+
11 TMDS Clock Shield 12 TMDS Clock-
13 CEC 14 N.C.
15 SCL 16 SDA
17 DDC/CEC Ground 18 +5 V Power
19 Hot plug detect
28 A26361-K1175-Z120-1-7619, edition 1
Loading...