Fujitsu Siemens Computers SCALEOVIEW Q22W-1, SCALEOVIEW H22-1W Operating Manual
Monitor
Operating Manual
English
SCALEOVIEW H22-1W/Q22W-1
Are there…
... any technical problems or other questions which you would like to be clarified?
Please contact
our help desk (see Warranty Booklet).
The latest information on our products, tips, updates, etc., can be found on the internet under:
http://www.fujitsu-siemens.com
This manual was produced by
Xerox Global Services
Published by
Fujitsu Siemens Computers GmbH
AG 03/07
Edition 1
Order no.: A26361-K1213-Z120-1-7619
SCALEOVIEW
H22-1W/Q22W-1
Operating Manual
March 2007 edition
VESA, DDC and DPMS are registered trademarks of Video Electronics Standards
Association.
Copyright © Fujitsu Siemens Computers GmbH 2007
All rights, including rights of translation, reproduction by printing, copying or similar methods,
in part or in whole, are reserved.
Offenders will be liable for damages.
All rights, including rights created by patent grant or registration of a utility model or design,
are reserved.
Delivery subject to availability. Right of technical modification reserved.
Contents
Introduction........................................................................................................................................... 1
Important notes..................................................................................................................................... 2
Safety notes.................................................................................................................................. 2
Power cable.................................................................................................................................. 3
Transport ...................................................................................................................................... 4
Cleaning ....................................................................................................................................... 4
CE marking................................................................................................................................... 4
FCC Class B Compliance Statement ........................................................................................... 5
Declaration of Conformity............................................................................................................. 6
Energy Star Guidelines................................................................................................................. 6
Disposal and recycling ................................................................................................................. 7
Checking the contents of the consignment........................................................................................... 7
Installing an ergonomic video workstation............................................................................................ 9
Mounting and removing the monitor base ..........................................................................................10
Mounting monitor base............................................................................................................... 10
Removing monitor base ............................................................................................................. 11
Connecting the monitor .............................................................................................................. 12
Connecting cables to the monitor............................................................................................... 12
Connecting cables to the computer............................................................................................ 14
Operation of the monitor..................................................................................................................... 16
Adjusting rake............................................................................................................................. 16
Switching the monitor on/off ....................................................................................................... 16
Notes on power management .................................................................................................... 17
Changing the monitor settings.................................................................................................... 18
Monitor settings using the OSD menu........................................................................................ 19
Operating of the camera..................................................................................................................... 24
Troubleshooting.................................................................................................................................. 25
Notes regarding the DIN EN ISO 13406-2 standard .......................................................................... 27
Technical data .................................................................................................................................... 28
VESA-DDC / CI 1,1-compatible VGA interface .......................................................................... 29
Preset operating modes ............................................................................................................. 29
Power supply plug ...................................................................................................................... 30
Monitor port DVI-D/DVI-I ............................................................................................................ 31
Pin assignment D-SUB............................................................................................................... 32
Pin assignment HDMI................................................................................................................. 32
S-Video port ............................................................................................................................... 33
A26361-K1213-Z120-1-7619, edition 1
Contents
A26361-K1213-Z120-1-7619
Introduction
Your new LCD (Liquid Crystal Display) monitor SCALEOVIEW H22-1W/Q22W-1 offers numerous
features and functions, for example:
● TFT display (Thin Film Transistor; active matrix)
● minimal space requirements thanks to slim casing
● optimum ergonomic characteristics (totally distortion-free, excellent picture definition and colour
purity right into the corners)
● high degree of brightness and good contrast
● high resolution: SCALEOVIEW H22-1W/Q22W-1 (1680 x 1050)
● size of the display area comparable to that of 24" CRT (Cathode Ray Tube) monitor
● presentation of up to 16.7 million colours (in conjunction with an appropriate graphics card)
● automatic scanning of horizontal frequencies from 30 to 83 kHz and refresh rates (vertical
frequencies) from 30 to 75 Hz (absolutely flicker-free)
● digital screen controller with microprocessor for storing 49 different display modes
● freely adjustable colour alignment for matching the screen colours to the colours of various
input and output devices
● convenient operation via integrated OSD (On-Screen-display) menu
● VESA-DDC compatibility
● VESA-FPMPMI compatibility (Flat Panel Monitor Physical Mounting Interface) - mechanical
interface to swivel arm and wall bracket)
● Plug & play capability
● power management for reducing power consumption when the computer is not in use
● compliance with the recommendations in accordance with TCO`03 (H22-1W), TCO`99
(Q22W-1)
In normal screen mode (dark characters against a light background) the monitor satisfies the
ergonomic requirements for the GS symbol.
This operating manual contains important information you require to start up and run your LCD
monitor.
A graphics card (screen controller) with VGA interface, a digital graphics card with DVI,
HDMI interface or Video interface (Composite Video and S-Video) is required to control the
SCALEOVIEW H22-1W/Q22W-1 LCD monitor. The monitor processes the data supplied to it by the
screen controller. The screen controller/the associated driver software is responsible for setting the
modes (resolution and refresh rate).
When putting the monitor into operation for the first time, the screen display should be optimally
adapted to the screen controller used and adjusted in accordance with your needs (see the
"
Changing the monitor settings" section in the "Operation of the monitor" chapter).
Target group
You don't need to be an "expert" to perform the operations described here. Do, however, read the
Important notes" chapter in the operating manual of the computer and in this operating manual.
"
In the event of any problems occurring, please contact your sales outlet or our help desk.
A26361-K1213-Z120-1-7619, edition 1 1
SCALEOVIEW H22-1W/Q22W-1
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
Pay particular attention to text marked with this symbol. Failure to observe this warning
!
endangers your life, destroys the device, or may lead to loss of data.
i
► Text which follows this symbol describes activities that must be performed in the order shown.
"Quotation marks" indicate names of chapters or terms.
This font indicates filenames and menu items.
This font indicates screen outputs.
Additional information
Details of how you set the resolution and refresh rate are provided in the documentation on your
screen controller/the associated driver software.
Supplementary information, remarks, and tips follow this symbol.
Important notes
In this chapter you will find information regarding safety which is essential to take note of
!
Safety notes
with your monitor.
This device complies with the relevant safety regulations for data processing equipment, including
electronic office machines for use in an office environment. If you have any questions, contact your
sales outlet or our help desk.
● The display surface of the LCD monitor is sensitive to pressure and scratches. You should
therefore be careful with the display surface so as to avoid lasting damage (Newton rings,
scratches).
● If the device is brought into the installation site from a cold environment, condensation can
form. Before operating the device, wait until it is absolutely dry and has reached approximately
the same temperature as the installation site.
● During installing and operating the device, please observe the instructions on environmental
conditions in the "
ergonomic video workstation
● To ensure sufficient ventilation, the intake and exhaust air openings of the monitor must never
be blocked.
● The monitor automatically sets itself to a mains voltage in the range of 100 V to 240 V. Ensure
that the local mains voltage lies within these limits.
● Ensure that the power socket on the device or the grounded mains outlet is freely accessible.
● The ON/OFF switch does not disconnect the device from the mains voltage. To completely
disconnect the mains voltage, remove the power plug from the socket.
Technical data" chapter as well as the instructions in the "Installing an
" chapter.
2 A26361-K1213-Z120-1-7619, edition 1
SCALEOVIEW H22-1W/Q22W-1
● The monitor is equipped with a power cable that complies with safety standards.
● Lay all cables so that nobody can stand on them or trip over them. When attaching the device,
observe the relevant notes in the "
● If you use a different data cable from the one supplied, ensure that it is adequately shielded.
CE conformance and optimum picture quality are guaranteed only if you use the data cables
supplied.
● No data transfer cables should be connected or disconnected during a thunderstorm.
● Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get inside the
device (danger of electric shock, short circuit).
● The device is not waterproof! Never immerse the device in water and protect it from spray
water (rain, sea water).
● In emergencies (e.g. damaged casing, elements or cables, penetration of liquids or foreign
matter), switch off the unit, disconnect the power plug and contact your sales outlet or our help
desk.
● The monitor must be disposed of in accordance with the local regulations for disposal of
special waste. The screen background lighting contains mercury. You must observe the
applicable handling and disposal safety regulations for fluorescent tubes.
● Only qualified technicians should repair the device. Unauthorised opening and incorrect repair
may greatly endanger the user (electric shock, fire risk).
Connecting the monitor" chapter.
● You may set only those resolutions and refresh rates specified in the "
Otherwise you may damage your monitor. If you are in any doubt, contact your sales outlet or
our help desk.
● Use a screen saver with moving images and activate the power management for your monitor
to prevent still images from "burning in".
● If you operate the monitor with the swivel arm or wall bracket, it may not be turned by 180°.
● We recommend that you place your device on an insensitive, non-slip surface. In view of the
multitude of different finishes and varnishes used on furniture, it is possible that the feet of the
device will mark the surface they stand on.
Technical data" chapter.
Power cable
To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary to
replace the original cable set.
● The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.
● The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the
outer sheath.
● For devices which are mounted on a desk or table, type SVT or SJT cable sets may be used.
For devices which sit on the floor, only SJT type cable sets may be used.
● The cable set must be selected according to the rated current for your device.
● If necessary, replace the original power cable with a regular grounded 3-core mains lead.
A26361-K1213-Z120-1-7619, edition 1 3
SCALEOVIEW H22-1W/Q22W-1
Transport
● Transport the monitor with care and only in its original packaging or another corresponding
packaging fit to protect it against knocks and jolts.
● Never drop the LCD monitor (danger of glass breakage).
Cleaning
● Always pull out the power plug before you clean the monitor.
● Do not clean any interior parts yourself, leave this job to a service technician.
● Do not use any cleaning agents that contain abrasives or may corrode plastic.
● Ensure that no liquid will run into the system.
● Ensure that the ventilation areas of the monitor are free.
● The display surface of the LCD monitor is sensitive to pressure and scratches. Clean it only
using a soft, slightly moistened cloth.
Wipe the monitor casing with a dry cloth. If the monitor is particularly dirty, use a cloth which has
been moistened in mild domestic detergent and then carefully wrung out.
CE marking
CE marking for devices without radio component up to 15/01/2007
The shipped version of this device complies with the requirements of the EEC directives
89/336/EEC "Electromagnetic compatibility" and 73/23/EEC "Low voltage directive".
CE marking for devices without radio component between 16/01/2007 and
19/07/2007
The shipped version of this device complies with the requirements of the EEC directives
89/336/EEC "Electromagnetic compatibility" and 2006/95/EC "Low voltage directive".
CE marking for devices without radio component introduced to the market
beginning with 20/07/2007
The shipped version of this device complies with the requirements of the EEC directives
2004/108/EC "Electromagnetic compatibility" and 2006/95/EC "Low voltage directive".
4 A26361-K1213-Z120-1-7619, edition 1
SCALEOVIEW H22-1W/Q22W-1
FCC Class B Compliance Statement
The following statement applies to the products covered in this manual, unless otherwise specified
herein. The statement for other products will appear in the accompanying documentation.
NOTE:
This equipment has been tested and found to comply with the limits for a "Class B" digital device,
pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian InterferenceCausing Equipment Standard ICES-003 for digital apparatus. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in strict
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between equipment and the receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
● Consult the dealer or an experienced radio/TV technician for help.
Fujitsu Siemens Computers GmbH is not responsible for any radio or television interference caused
by unauthorised modifications of this equipment or the substitution or attachment of connecting
cables and equipment other than those specified by Fujitsu Siemens Computers GmbH. The
correction of interferences caused by such unauthorised modification, substitution or attachment will
be the responsibility of the user.
The use of shielded I/O cables is required when connecting this equipment to any and all optional
peripheral or host devices. Failure to do so may violate FCC and ICES rules.
A26361-K1213-Z120-1-7619, edition 1 5
Loading...