Fujitsu Siemens Computers MYRICA V27-1, MYRICA V32-1 Operating Manual

A26361-K1037-Z120-1-M119, edition 1 English
Contents
Introduction........................................................................................................................................... 1
Notational conventions ................................................................................................................. 2
Important notes..................................................................................................................................... 2
Safety notes.................................................................................................................................. 2
Cleaning ....................................................................................................................................... 3
Transport ...................................................................................................................................... 4
Power cable.................................................................................................................................. 4
CE marking................................................................................................................................... 4
Disposal and recycling ................................................................................................................. 4
Preparing for use .................................................................................................................................. 5
Unpacking and checking the delivery........................................................................................... 5
Preparing remove control ............................................................................................................. 5
Inserting batteries................................................................................................................. 5
Replacing batteries............................................................................................................... 6
Installing LCD TV ......................................................................................................................... 6
Connections on LCD TV............................................................................................................... 7
Connecting LCD TV ................................................................................................................... 10
Switching LCD TV on/off ............................................................................................................ 11
Setting language of the OSD menu............................................................................................ 12
Carrying out programme search................................................................................................. 12
Adjusting programme settings....................................................................................................13
Arranging programmes....................................................................................................... 13
Changing programme properties........................................................................................ 14
Setting the channel.............................................................................................................15
Add Programs ....................................................................................................................16
Operation............................................................................................................................................ 17
Operating elements on the device.............................................................................................. 17
Changing the device settings with the buttons of the control panel ........................................... 18
Remote control ........................................................................................................................... 19
PIP (Picture in Picture)....................................................................................................... 19
Teletext............................................................................................................................... 20
Changing device settings with remote control............................................................................ 21
Description of menus.................................................................................................................. 22
DISPLAY menu - default picture settings........................................................................... 23
ADVANCED menu - advanced picture settings ................................................................. 24
GEOMETRY menu - picture position and sharpness......................................................... 25
TV SETUP menu - setting channels................................................................................... 26
AUDIO menu - sound settings............................................................................................ 27
SYSTEM menu - system settings....................................................................................... 27
Display modes.................................................................................................................................... 28
Main display mode ..................................................................................................................... 28
PIP mode (Picture in Picture) ..................................................................................................... 29
Technical data .................................................................................................................................... 30
VESA-DDC-compatible VGA interface....................................................................................... 32
Preset operating modes ............................................................................................................. 32
Power consumption.................................................................................................................... 32
PC Analogue (D-SUB)................................................................................................................ 33
PC Digital (DVI-D) ...................................................................................................................... 33
SCART (Half/Full)....................................................................................................................... 34
S-Video....................................................................................................................................... 34
Colour and transmission system by country............................................................................... 35
Troubleshooting.................................................................................................................................. 38
A26361-K1037-Z120-1-M119, edition 1 English - 1
Introduction
Your new LCD TV MYRICA V27-1 / V32-1possesses a whole range of useful features and functions, e.g.:
TFT monitor (Thin Film Transistor; active matrix)
analogue tuner for VHF, UHF and cable programmes
connections for SCART (video and RGB), video and S-Video
minimal space requirements thanks to slim casing
optimum ergonomic characteristics (totally distortion-free and colour purity right into the
corners)
high degree of brightness and good contrast
high resolution for operation on a PC
easy-to-operate remote control
convenient operation via integrated OSD (On Screen Display) menu
2 tuner picture-in-picture, video (secondary) in PC picture (primary)
picture size changeover: full-screen, 4:3, zoom1 (16:9) and zoom2
integrated loudspeakers
integrated NICAM/IGR sound decoder for stereo and two-channel sound
Sleep timer
Teletext
This operating manual contains important information you require to start up and run your device. For TV operation with the integrated tuner, a terrestrial antenna or a cable connection is required. As
an alternative, a satellite receiver can be connected to one of the SCART jacks. When you put the device into operation for the first time, you should carry out a programme search
(see the chapter "Preparing for use").
Target group
You don't need to be an "expert" to perform the operations described here. Do, however, read the "Important notes" chapter in the operating manual of the computer and in this operating manual.
In the event of any problems occurring, please contact your sales outlet or our help desk.
Additional information
Details of how you set the resolution and refresh rate are provided in the documentation on your screen controller/the associated driver software.
LCD TV MYRICA V27-1 / V32-1
2 - English A26361-K1037-Z120-1-M119, edition 1
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
!
Pay particular attention to text marked with this symbol. Failure to observe this warning endangers your life, destroys the device, or may lead to loss of data.
i
Supplementary information, remarks, and tips follow this symbol.
Text which follows this symbol describes activities that must be performed in the order shown. "Quotation marks" indicate names of chapters or terms. Texts in italics indicate filenames and menu items.
Important notes
!
In this chapter you will find information regarding safety which is essential to take note of with your LCD TV.
!
This product from Fujitsu Siemens Computers contains intellectual property of third parties. Any tampering with or modification of the product will void the warranty and may lead to legal prosecution to the full extent of the law.
Safety notes
This device complies with the relevant safety regulations for data processing equipment, including electronic office machines for use in an office environment. If you have any questions, contact your sales outlet or our help desk.
The display surface of the LCD TV is sensitive to pressure and scratches. You should therefore be careful with the display surface so as to avoid lasting damage (Newton rings, scratches).
If the device is brought into the installation site from a cold environment, condensation can form. Before operating the device, wait until it is absolutely dry and has reached approximately the same temperature as the installation site.
During installation and before operating the device, please observe the instructions on environmental conditions in the "Technical data" chapter as well as the instructions in the "Preparing for use" chapter.
To ensure sufficient ventilation, the intake and exhaust air openings of the device must never be blocked.
The device automatically sets itself to the correct voltage within the range from 100 V to 240 V. Ensure that the local mains voltage lies within these limits.
Ensure that the power socket on the device or the earthed mains outlet is freely accessible.
To completely disconnect the mains voltage, remove the power plug from the socket.
Lay all cables so that nobody can stand on them or trip over them. When attaching the device,
observe the relevant notes in the "Preparing for use" chapter.
LCD TV MYRICA V27-1 / V32-1
A26361-K1037-Z120-1-M119, edition 1 English - 3
If you use a different PC data cable from the one supplied, ensure that it is adequately shielded. CE conformance and optimum picture quality are guaranteed only if you use the data cable supplied.
No antenna or data transfer cables should be connected or disconnected during a thunderstorm.
Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get inside the device (danger of electric shock, short circuit).
The device is not waterproof! Protect the device from spray water (rain, sea water).
In emergencies (e.g. damaged casing, elements or cables, penetration of liquids or foreign
matter), switch off the unit, disconnect the power plug and contact your sales outlet or our help desk.
The device must be disposed of in accordance with the local regulations for disposal of special waste. The screen background lighting contains mercury. You must observe the applicable handling and disposal safety regulations for fluorescent tubes.
Only qualified technicians should repair the device. Unauthorised opening and incorrect repair may greatly endanger the user (electric shock, fire risk).
You may set only those resolutions and refresh rates specified in the "Technical data" chapter.
Use a screen saver with moving images in PC mode and activate the power management for
your monitor to prevent still images from "burning in".
Keep this operating manual together with your device. If you pass on the device to third parties, you should include this manual.
Cleaning
Remove the power plug before cleaning the device.
Do not clean any interior parts yourself, leave this job to a service technician.
Do not use any cleaning agents that contain abrasives or may corrode plastic.
Ensure that no liquid will run into the system.
Ensure that the ventilation areas of the device are free.
The display surface of the LCD TV is sensitive to pressure and scratches. Clean it only using a
soft, slightly moistened cloth.
Wipe the LCD TV casing with a dry cloth. If the monitor is particularly dirty, use a cloth which has been moistened in mild domestic detergent and then carefully wrung out.
LCD TV MYRICA V27-1 / V32-1
4 - English A26361-K1037-Z120-1-M119, edition 1
Transport
Transport the device with care and only in its original packaging or another corresponding packaging to protect it from knocks and jolts.
Never drop the LCD TV (danger of glass breakage).
Power cable
To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary to replace the original cable set.
The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.
The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the
outer sheath.
For devices which are mounted on a desk or table, type SVT or SJT cable sets may be used. For devices which sit on the floor, only SJT type cable sets may be used.
The cable set must be selected according to the rated current for your device.
CE marking
The shipped version of this device complies with the requirements of the EEC directives 89/336/EEC "Electromagnetic compatibility" and 73/23/EEC "Low voltage directive".
Disposal and recycling
This device has been manufactured to the highest possible degree from materials which can be recycled or disposed of in a manner that is not environmentally damaging. The device may be taken back after use to be recycled, provided that it is returned in a condition that is the result of normal use. Any components not reclaimed will be disposed of in an environmentally acceptable manner.
If you have questions on disposal, please contact your point of sale, our Help Desk or obtain information at: www.fujitsu-siemens.com/recycling
LCD TV MYRICA V27-1 / V32-1
A26361-K1037-Z120-1-M119, edition 1 English - 5
Preparing for use
Unpacking and checking the delivery
!
The display surface of the LCD TV is sensitive to pressure and scratches. Always hold the device by the casing!
Unpack all the individual parts. ► Check the delivery for damage incurred during transportation. ► Check whether the delivery agrees with the details in the delivery note.
The complete LCD TV package includes: – one LCD TV
one power cable – one remote control – two batteries type AAA – this manual – one Warranty Booklet
Should you discover that the delivery does not correspond to the delivery note, notify your local sales outlet immediately.
i
We recommend that you keep the original packaging material. Keep it for future transportation.
Preparing remove control
Inserting batteries
Open the back cover of the remote control by
sliding it in the direction of the arrow.
Place the batteries supplied in the battery
compartment. Ensure correct polarity.
Close the battery compartment by sliding the
cover back on until you hear and feel it click into place.
i
Remove the batteries when not using the remote control for longer periods. Handle the remote control with care. Do not drop the remote control on the floor. Do not expose the remote control to moisture, direct sunlight or high temperatures.
LCD TV MYRICA V27-1 / V32-1
6 - English A26361-K1037-Z120-1-M119, edition 1
Replacing batteries
When the batteries are used up, replace them with two batteries of the same type (type AAA). Do not throw batteries or accumulators into the household waste. They must be disposed of in
accordance with local regulations concerning special waste.
Installing LCD TV
!
To ensure sufficient ventilation, the intake and exhaust air openings of the device must never be blocked.
>10 cm >10 cm>10 cm
>5 cm
>5 cm >5 cm
When installing the TV in niches, maintain the minimum distance for sufficient ventilation of the device: 5 cm from the side and back, 10 cm from the top.
LCD TV MYRICA V27-1 / V32-1
A26361-K1037-Z120-1-M119, edition 1 English - 7
Connections on LCD TV
!
Observe the safety precautions in the "Important notes" chapter in this operating manual. Do not cover the ventilation openings of the monitor. Never open the housing of the power supply unit. There is extreme danger from an
electrical shock with the housing open. There are no components requiring cleaning or repairs in the interior.
MYRICA V32-1
2
34
9
11
13
14
1
12
10
5678
15
16
MYRICA V27-1
3
4
9
11
13
14
12
10
5678
15
16
1 = Connection terminals for external
loudspeakers
2 = Sliding switch for changing over from
internal to external loudspeakers 3 = DVI port 4 = VGA port 5 = PC AUDIO IN 6 = LINE OUT 7 = SUBWOOFER port
8 = COMPONENT ports (AUDIO) 9 = COMPONENT ports (YPbPr) 10 = RS-232C port 11 = SCART1 port 12 = SCART2 port 13 = AV ports 14 = S-VIDEO IN ports 15 = Antenna port 16 = Power connector
LCD TV MYRICA V27-1 / V32-1
8 - English A26361-K1037-Z120-1-M119, edition 1
The following devices can be connected to this LCD TV:
SPEAKER red/right/+
black/right/­black/left/­red/left/+
Connection terminals for external loudspeakers With the sliding switch you change over from internal to
external loudspeakers and vice versa. The connections are located on the back (V27-1) or on the
underside (V32-1) of the LCD TV.
DVI (white)
Connection for digital video input signals e.g. a PC with a digital output (DVI-D) or for HDTV devices
VGA (blue)
Connection for analogue VGA input signals e.g. for a PC with an analogue output (D-SUB)
PC AUDIO IN (blue)
Connection for audio input signals (LINE IN) e.g. for a PC or for HDTV devices
LINE OUT (green)
Port for headphones
SUBWOOFER (black)
Connection for an active subwoofer
COMPONENT: Y
green Pb
blue Pr
red
AUDIO red (right)
white (left)
Connections for component input signals e.g. for HDTV decoder or HDTV video recorder
RS-232C (black)
Serial port For customer service, e.g. for updating the firmware
LCD TV MYRICA V27-1 / V32-1
A26361-K1037-Z120-1-M119, edition 1 English - 9
SCART1 Connection for AV, RGB and audio input signals
e.g. for satellite receiver, DVD player, video recorder, camcorder, decoders or a gaming console
Out (TV-signal): e.g. video recorder, dvd recorder
SCART2 Connection for AV, RGB and audio input signals
e.g. for satellite receiver, DVD player, video recorder, or a gaming console
Out (picture signal)
AV: AUDIO red (right) white (left)
VIDEO yellow
Connections for video and audio input signals e.g. for DVD player, video recorder, film camera with S-Video
connection or gaming console
S-VIDEO IN: AUDIO red (right) white (left)
S-VIDEO
Connections for S-video and audio input signals e.g. for DVD player, video recorder, a film camera with S-
Video connection or a PC
TV-ANT. antenna port
AC INPUT Connector for the power cable
LCD TV MYRICA V27-1 / V32-1
10 - English A26361-K1037-Z120-1-M119, edition 1
Connecting LCD TV
Connecting antenna
Connect an antenna cable to the device and the
TV antenna socket.
Connecting the power supply
Plug the power cable supplied into the power
connector of the LCD TV.
You will find the power connector on the underside of the LCD TV.
Connect the connector of the power cable
supplied into a properly earthed mains outlet and ensure a secure connection.
LCD TV MYRICA V27-1 / V32-1
A26361-K1037-Z120-1-M119, edition 1 English - 11
Switching LCD TV on/off
MYRICA V27-1
Press the On/Off switch at the lower right on the
front of the LCD TV.
MYRICA V32-1
Press the On/Off switch at the lower left on the
front of the LCD TV.
From the indicator at the lower right on the front of the LCD TV you can recognise whether the device is in operation, in the standby mode or switched off.
Green Red Dark
= = =
The device is switched on. The device is in standby mode. The device is switched off.
Loading...
+ 28 hidden pages