Fujitsu Siemens Computers D2130 Tehnical Manual

PRIMERGY

System board D2130
for RX220

Technical manual

Däschlein
Fujitsu Siemens Computers GmbH München
81730 Munich
e-mail: email: [e-mail]
Tel.: [phone]
Fax: (++49) 700 / 372 00000
D2130 (RX220)
Sprachen: En

Edition September 2005

Comments… Suggestions… Corrections…

The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.

Fax forms for sending us your comments are included in
the back of the manual.

There you will also find the addresses of the relevant
User Documentation Department.

Certified documentation
according to DIN EN ISO 9001:2000

To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.

cognitas. Gesellschaft für Technik-Dokumentation mbH

www.cognitas.de

Copyright and Trademarks

Copyright © 2005 Fujitsu Siemens Computers GmbH.

All rights reserved.
Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers.

D2130 (RX220)

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 CE certificate . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.3 Environment protection . . . . . . . . . . . . . . . . . . . . . 11

3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.2 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.3 Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.3.1 ISA bus resources . . . . . . . . . . . . . . . . . . . . . . . . 19

3.3.2 PCI resources . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.4 Screen resolution . . . . . . . . . . . . . . . . . . . . . . . . 21

3.5 Temperature / system monitoring . . . . . . . . . . . . . . . . 22

3.6 Interfaces and connectors . . . . . . . . . . . . . . . . . . . . 23

3.6.1 External connectors . . . . . . . . . . . . . . . . . . . . . . . 24

3.7 Settings with jumpers . . . . . . . . . . . . . . . . . . . . . . 26

4 Replacing the lithium battery . . . . . . . . . . . . . . . . . 29

Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

D2130 (RX220) 5

1Introduction

This technical manual describes the system board D2130, which can be
equipped with one or two AMD Opteron™/Dual Core Opteron™ processors.

Further information about drivers is provided in the readme files on the hard
disk, on the supplied "ServerSupport" or "ServerStart" CDs.

You will find further information in the BIOS description "D2130 Setup Utility for
RX220".

Notational conventions

The meanings of the symbols and fonts used in this manual are as follows:

italics indicates commands, menu items, file and path

names or software programs

fixed font indicate system output on the monitor

semi-bold fixed
font

indicates values to be entered through the keyboard

[Key symbol] indicates keys according to their representation on the

keyboard
If capital letters are to be entered explicitly, then the

Shift key is shown, e.g. [SHIFT] - [A] for A.
If two keys need to be pressed at the same time, then

this is shown by placing a hyphen between the two key
symbols.

“quotation marks” indicates names and terms that are being empha-

sized.

Ê indicates an operation that to be performed

V CAUTION! indicates warnings, which, if ignored, will endanger

your health, destroy the system or lead to the loss of
data.

I indicates additional information, notes and tips

Table 1: Notational conventions

D2130 (RX220) 7

2 Important notes

In this chapter you will find essential information regarding safety when working
with your server.

V CAUTION!

With the system board installed you must open the system to access the
system board. How to dismantle and reassemble the system is described
in the Options Guide accompanying your system.

2.1 Notes on safety

V CAUTION!

● The actions described in these instructions should only be performed

by authorized, qualified personnel. Equipment repairs should only be
performed by qualified staff. Any failure to observe the guidelines in
this manual, and any unauthorized openings and improper repairs
could expose the user to risks (electric shock, fire hazards) and could
also damage the equipment. Please note that any unauthorized
openings of the device will result in the invalidation of the warranty
and exclusion from all liability.

● Transport the device only in the antistatic original packaging or in

packaging that protects it from knocks and jolts.

● Only install expansions that are allowed for the system board. If you

install other expansions, you may damage the requirements and rules
governing safety and electromagnetic compatibility or your system.
Information on which system expansions are suitable can be
obtained from the customer service centre or your sales outlet.

● The warranty expires if the device is damaged during the installation

or replacement of system expansions.

8 D2130 (RX220)

Notes on safety Important notes

V ● Components can become very hot during operation. Ensure you do

not touch components when making extensions to the system board.
There is a danger of burns!

● Transmission lines to peripheral devices must be adequately

shielded.

● To the LAN wiring the requirements apply in accordance with the

standards EN 50173 and EN 50174-1/2. As minimum requirement
the use of a protected LAN line of category 5 for 10/100 MBps
Ethernet, and/or of category 5e for Gigabit Ethernet is considered.
The requirements of the specification ISO/IEC 11801 are to be
considered.

● Never connect or disconnect data transmission lines during a storm

(lightning hazard).

Batteries

V CAUTION!

● Incorrect replacement of lithium battery may lead to a risk of

explosion. The batteries may only be replaced with identical batteries
or with a type recommended by the manufacturer.

It is essential to observe the instructions on page 29.

D2130 (RX220) 9

Important notes Notes on safety

Modules with electrostatic-sensitive components

Systems and components that might be damaged by electrostatic discharge
(ESD) are marked with the following label:

Figure 1: ESD label

When you handle components fitted with ESDs, you must observe the following
points under all circumstances:

● You must always discharge yourself of static charges (e.g. by touching a

grounded object) before working.

● The equipment and tools you use must be free of static charges.

● Remove the power plug from the power socket before inserting or removing

boards containing ESDs.

● Always hold boards with ESDs by their edges.

● Never touch pins or conductors on boards fitted with ESDs.

● Use a grounding cable designed for this purpose to connect yourself to the

system unit as you install/deinstall the board.

● Place all components on a static-safe base.

I You will find a detailed description for handling ESD components in the

relevant European or international standards (EN 61340-5-1,
ANSI/ESD S20.20).

10 D2130 (RX220)

CE certificate Important notes

Notes about boards

● During installation/deinstallation of the system board, observe the specific

instructions described in the service manual for the server.

● Remove the plug from the mains outlet so that system and system board are

totally disconnected from the mains voltage.

● To prevent damage to the system board, the components and conductors on

it, please take great care when you insert or remove boards. Take great care
to ensure that extension boards are slotted in straight, without damaging
components or conductors on the system board, or any other components,
for example EMI spring contacts

● Be careful with the locking mechanisms (catches, centring pins etc.) when

you replace the system board or components on it, for example memory
modules or processors.

● Never use sharp objects (screwdrivers) for leverage.

2.2 CE certificate

The shipped version of this board complies with the requirements
of the EEC directive 89/336/EEC "Electromagnetic compatibility".

Compliance was tested in a typical PRIMERGY configuration.

D2130 (RX220) 11

Important notes Environment protection

2.3 Environment protection

Environmentally-friendly product design and development

This product has been designed in accordance with the Fujitsu Siemens
Computers standard for “environmentally friendly product design and devel­opment”. This means that key factors such as durability, selection and labeling
of materials, emissions, packaging, ease of disassembly and recycling have
been taken into account.

This saves resources and thus reduces the harm done to the environment.

Notes on saving energy

Devices that do not have to be on permanently should not be switched on until
they need to be used and should be switched off during long breaks and on
completion of work

Notes on packaging

Please do not throw away the packaging. You may need it later for transporting
your system unit. If possible, the device should only be transported in its original
packaging.

Notes on dealing with consumables

Please dispose of printer consumables and batteries in accordance with local
government regulations.

Do not throw batteries and accumulators into the household waste. They must
be disposed of in accordance with local regulations concerning special waste.

All batteries containing pollutants are marked with a symbol (a crossed-out
rubbish bin on wheels). In addition, the marking is provided with the chemical
symbol of the heavy metal decisive for the classification as a pollutant:

Cd Cadmium
Hg Mercury
Pb Lead

12 D2130 (RX220)

Environment protection Important notes

Notes on labeling plastic housing parts

Please avoid attaching your own labels to plastic housing parts wherever
possible, since this makes it difficult to recycle them.

Returning, recycling and disposal

For details on take-back and reuse of devices and consumables within Europe,
see the manual „Returning used devices“ or contact your Fujitsu Siemens
Computers branch office/subsidiary or our recycling center in Paderborn:

Fujitsu Siemens Computers
Recycling Center
D-33106 Paderborn
Germany

Tel. [phone]
Fax [phone]
Internet: www.fujitsu-siemens.com/recycling

The device may not be disposed of with household rubbish. This
appliance is labelled in accordance with European Directive
2002/96/EC concerning used electrical and electronic appliances
(waste electrical and electronic equipment - WEEE).
The guideline determines the framework for the return and recycling
of used appliances as applicable throughout the EU. To return your
used device, please use the return and collection systems available
to you. You will find further information on this at www.fujitsu-
siemens.com/recycling.

D2130 (RX220) 13

3 Features

3.1 Overview

Processors

– 1 or 2 x AMD Opteron™/Dual Core Opteron™ processors
– 2 processor sockets 940 for AMD Opteron™/Dual Core Opteron™

processors with 2.0 GT/ 1.6 GT HyperTransport bandwidth

Main memory

– 8 slots for main memory DDR1/400 MHz (registered),

SDRAM memory modules,

dual channel with 2 modules per channel with 512 MB, 1 and 2 Gbyte
– maximum 16 Gbyte of memory
– ECC multiple bit error detection and single bit error correction
– memory scrubbing function

Chips on the system board

– ServerWorks HT-2000 (Northbridge)
– ServerWorks HT-1000 (Southbridge)
– 2 embedded dual Broadcom Gigabit LAN controllers
– VGA controller (ATI Radeon 7000M) onboard with 16 MB SDRAM memory
– SATA controller Promise PDC20319u
– Super I/O controller (NS PC87417)
– Flash EPROM for:

–BIOS

–LAN

– Server Management (SM)
– server management with BMC (FSC System)
– thermal and system management controller (ADM1026)