Page 1
6<67(0%2$5''
$'',7,21$/7(&+1,&$/
0$18$/
Page 2
Are there ...
... any technical problems or other
questions you need clarified?
Please contact:
• Our Hotline:
Mo-Fr: 8 a.m. - 6 p.m.
Sat: 9 a.m. - 2 p.m.
Tel.: ++49 (0) 180 3777 005
• your sales outlet
The latest information on our products, tips, updates, etc., can be found on the Internet under:
http://www.fujitsu-siemens.com/mainboard
Page 3
Page 4
'LHVHV+DQGEXFKZXUGHDXI5HF\FOLQJ3DSLHUJHGUXFNW
7KLVPDQXDOKDVEHHQSULQWHGRQUHF\FOHGSDSHU
&HPDQXHOHVWLPSULPpVXUGXSDSLHUUHF\FOp
(VWHPDQXDOKDVLGRLPSUHVRVREUHSDSHOUHFLFODGR
4XHVWRPDQXDOHqVWDWRVWDPSDWRVXFDUWDGDULFLFODJJLR
'HQQDKDQGERNlUWU\FNWSnUHF\FOLQJSDSSHU
'LWKDQGERHNZHUGRSUHF\FOLQJSDSLHUJHGUXNW
+HUDXVJHJHEHQYRQ3XEOLVKHGE\
)XMLWVX6LHPHQV&RPSXWHUV*PE+
%HVWHOO1U2UGHU1R
3ULQWHGLQWKH)HGHUDO5HSXEOLFRI*HUPDQ\
$*
A26361-D1192-Z180-1-7619
$'=
Page 5
Page 6
Page 7
System Board D1192
Additional Technical Manual
September 2000 edition
Page 8
Intel, Pentium and Celeron are registered trademarks of Intel Corporation, USA.
Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation.
PS/2 and OS/2 Warp are registered trademarks of International Business Machines, Inc.
Magic Packet is a registered trademark of Advanced Micro Devices, Inc.
Rambus, RDRAM, and the Rambus Logo are registered trademarks of Rambus Inc. Direct
Rambus, RIMM, SO-RIMM, and Direct RDRAM are trademarks of Rambus Inc.
All other trademarks referenced are trademarks or registered trademarks of their respective
owners, whose protected rights are acknowledged.
Copyright
All rights, including rights of translation, reproduction by printing, copying or similar methods,
even of parts are reserved.
Offenders will be liable for damages.
All rights, including rights created by patent grant or registration of a utility model or design, are
reserved. Delivery subject to availability.
Right of technical modification reserved.
This manual was produced by
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Fujitsu Siemens Computers GmbH 2000
Page 9
Contents
Introduction................................................................................................................................................1
Features.....................................................................................................................................................1
Mechanics .................................................................................................................................................2
Connectors........................................................................................................................................4
Power supply monitoring...........................................................................................................4
Front panel connector...............................................................................................................5
Serial chipcard reader or internal serial port 2 (COM 2)...........................................................6
Fan 2 connector (Auxiliary).......................................................................................................6
Intrusion connector for case open detect for optional push-button (opener)............................6
USB chipcard reader................................................................................................................7
Wake On LAN (WOL) connector..............................................................................................7
Auxiliary (MPEG, TV) audio connector (internal)......................................................................7
CD-ROM audio connector (internal).........................................................................................8
Power supply +3.3 V for AGP Pro............................................................................................8
Power supply +12 V..................................................................................................................8
Fan 3 connector (system).........................................................................................................9
Fan 1 connector (processor)....................................................................................................9
Configuration.....................................................................................................................................9
Functions controlled by the configuration switch......................................................................9
Power..............................................................................................................................................10
Power requirement..................................................................................................................10
Documentation.........................................................................................................................................10
Installing drivers.......................................................................................................................................11
Upgrading main memory.........................................................................................................................11
Troubleshooting.......................................................................................................................................12
Power loadability.....................................................................................................................10
Message BIOS update....................................................................................................................12
The screen stays blank...................................................................................................................12
A26361-D1192-Z180-1-7619
Page 10
Page 11
Introduction
Depending on the configuration of your system board, some of the hardware components
described may not be available.
i
You may find further information e. g. in the complete Technical Manual for the system board and in the
description "BIOS Setup".
Further information to drivers is provided on the supplied drivers diskettes or on the "Drivers & Utilities"
or "ServerStart" CD. For detailed information please look at chapter "Installing drivers
BIOS version or drivers can be found on the internet under http://www.fujitsu-siemens.com/en/service.
". The latest
Features
Function Version D1192-A1X Function Version D1192-A1X
Processor socket PGA 423 System monitoring x
Processor Pentium 4 Thermal Management x
Formfactor ATX AOL with onboard LAN x
Front Side Bus in MHz 100 Wake On LAN x
Chipset i850 Chipcard reader x
Memory sockets 4 RIMM Save to Disk (ACPI S4) x
PCI slots 5 Save to RAM(ACPI S3) x
AGP slot 1 LAN onboard Ethernet Controller
CNR slot 1 Audio onboard AD1885
Computer system boards and components contain very delicate IC chips. To protect them
against damage caused from electric static, you have to follow some precautions:
!
• Unplug your computer when you work inside.
• Hold components by the edge, don’t touch their leads.
• Use a grounded wrist strap.
Place the system board and the components on a grounded antistatic pad whenever you
work outside the computer.
Once you have installed the system board, you should remove the battery protection (i.e. the
thin plastic plate between battery and contact spring).
82550
A26361-D1192-Z180-1-7619 English - 1
Page 12
Mechanics
Mechanics
Layout
ATX 12" x 8’’ (304.8 mm x 203.2 mm)
Some of the following connectors are optional and may therefore not be included on your system
board.
RIMM 4
RIMM 3
RIMM 2
RIMM 1
AGP Pro
PCI 4
PCI 1
PCI 3
PCI 2
PCI 5
CNR
8
7
9a 9c9b
1 = Game/Midi port
9a = Audio Line-Out
9b = Audio Line-In
9c = Audio Micro-In
2
1 = PS/2 mouse port
2 = PS/2 keyboard port
3 = Parallel port
4 = Serial port 1
31
456
5 = USB port 2
6 = USB port 1
7 = LAN port
The components and connectors marked are not necessarily present on the system board.
2 - English A26361-D1192-Z180-1-7619
Page 13
Mechanics
1
RIMM 4
RIMM 3
RIMM 2
RIMM 1
2345
6 7
89
19
AGP Pro
PCI 1
PCI 2
1817 16
1 = Power supply monitoring
2 = Connector for control panel and loudspeaker
3 = Power supply
4 = IDE drives 3 and 4 (secondary)
5 = Floppy disk drive
6 = IDE drives 1 and 2 (primary)
7 = Serial chipcard reader interface or serial port
2
8 = Fan 2 (AUX)
9 = IrDA
The components and connectors marked are not necessarily present on the system board.
10 = I²C port
11 = Cover monitoring
12 = USB chipcard reader or USB front panel
13 = Wake On LAN (WOL)
14 = CD audio input
15 = AUX audio input
16 = Power supply +3.3 V for AGP Pro
17 = Power supply +12 V
18 = Fan (system)
19 = Fan 1 (for the processor)
PCI 4
PCI 3
PCI 5
CNR
1415
10
11
12
13
A26361-D1192-Z180-1-7619 English - 3
Page 14
Mechanics
Connectors
Some of the following connectors are optional!
!
Power supply monitoring
Pin Signal
1 AC Outlet on (high asserted)
2 PS FAN Control (low asserted)
3 PS FAN full on (low asserted)
4 PS FAN pulse
5 SMB CLK
6 SMB DATA
7 VCC EEPROM (+3.3 V)
8 GND
1
4 - English A26361-D1192-Z180-1-7619
Page 15
Mechanics
Front panel connector
Power On/Off
1)
Reset
1)
Sleep
1) Cable is not included in the delivery scope.
2) The same in terfac e
3) 2pin or 3pin connector possible
Message LED
1)
HD-LED
SCSI LED Input
1)
Power On LED
2)1)
Pin Signal Pin Signal
1 GND 2 Speaker
3 Standby LED (Anode) 4 Key
5 Key 6 GND
7 PON_LED (Anode) 8
1)
VCC or GND
9 PON_LED (Anode) 10 Key pin
11 PON_LED (Cathode/GND)
12 Key pin
Standby LED (Cathode/GND)
13 Message LED (Anode) 14 Key
15 Message LED (Cathode) 16 Not connected
17 Key 18 SCSI LED input (low asserted)
19 HD_LED (Anode) 20 SCSI LED input (low asserted)
21 HD_LED (Cathode) 22 Not connected
23 GND 24 Key
25 Power button (low asserted) 26 GND
2)
27
reserved 28 GND
29 Reset button (low asserted) 30 GND
1) Pin 8 is connected to VCC if audio is not onboard.
Pin 8 is connected to GND if audio is onboard.
Standby LED
Speaker
1) 3)
1
2
2)
A26361-D1192-Z180-1-7619 English - 5
Page 16
Mechanics
Serial chipcard reader or internal
2
serial port 2 (COM 2)
external via optional cable
1
Pin Signal Pin Signal
1 DCD 2 2 DSR 2
3 SIN 2 4 RTS 2
5 SOUT 2 6 CTS 2
7 DTR 2 8 PC_On_Strobe
9 GND 10 VCC Auxiliary
11 Not connected 12 VCC
13 Not connected 14 GND
15 GND 16 Key
(TTL-Signal, low asserted)
Fan 2 connector (Auxiliary)
1
Pin Signal
1 GND
2 Controlled fan voltage (0 V / 6...12 V)
3 Fan sense
Intrusion connector for case open
1
detect for optional push-button
(opener)
Pin Signal
1 GND
2 Case open (low asserted)
3 Intrusion switch present (low asserted)
6 - English A26361-D1192-Z180-1-7619
Page 17
Mechanics
USB chipcard reader
1
Pin Signal Pin Signal
1 P3V3P_DUAL 2 VCC
3 Data negative up 4 Data positive up
5 Data negative down 6 Data positive down
7 GND 8 GND
9 Chipcard present 10 VCC auxiliary
11 P3V3P 12 Power OK (high asserted)
13 Chipcard reader On (low pulse) 14 Key
2
Wake On LAN (WOL) connector
1
Pin Signal
1 VCC Auxiliary
2 GND
3 Wake pulse (high asserted)
Auxiliary (MPEG, TV) audio connector (internal)
1
Pin Signal
1 Left AUX audio input
2 Analog GND
3 Analog GND
4 Right AUX audio input
A26361-D1192-Z180-1-7619 English - 7
Page 18
Mechanics
CD-ROM audio connector (internal)
Pin Signal
1 Left CD audio input
2 CD GND
3 CD GND
4 Right CD audio input
1
Power supply +3.3 V for AGP Pro
Pin Signal
1 GND
2 +3.3 V
3 +3.3 V
4 GND
5 GND
6 +3.3 V
Power supply +12 V
Pin Signal
1 GND
2 GND
3 +12 V
4 +12 V
1
1
8 - English A26361-D1192-Z180-1-7619
Page 19
Mechanics
Fan 3 connector (system)
1
Pin Signal
1 GND
2 Controlled fan voltage (0 V / 6...12 V)
3 Fan sense
Fan 1 connector (processor)
1
Pin Signal
1 GND
2 Controlled fan voltage (0 V / 6...12 V)
3 Fan sense
Configuration
Functions controlled by the configuration switch
Function SKP RCV FWP AUX
Password skip on X X X
Off off X X X
Recovery BIOS X on X X
Off X off X X
Floppy write protect X X on X
Off X X off X
Auxiliary Current low (0.7 A) X X X on
Auxiliary Current (2 A) X X X off
A26361-D1192-Z180-1-7619 English - 9
Page 20
Documentation
Power
Power requirement
Source Voltage Maximum variation Maximum current Comment
Main power supply +5.0 V ±5 % 8.0 A
Main power supply +12 V ±10 % 9.0 A
Main power supply -12 V ±10 % 0.5 A
Main power supply +3.3 V ±5 % 3.0 A
Auxiliary power supply +5.0 V ±5 % 2 A
For systemboard with processor and memory. Without AGP and PCI cards.
Power loadability
Fuse
number
Maximum fuse
current
1 750 mA Keyboard port Not specified
2 750 mA Universal serial bus (USB) Port A 500 mA
3 750 mA Universal serial bus (USB) Port B 500 mA
4 750 mA Universal serial bus (USB) Port C 500 mA
5 750 mA Universal serial bus (USB) Port D 500 mA
Function Maximum function current
Mouse port Not specified
Game port Not specified
Documentation
Ê Insert the "Drivers & Utilities" CD.
Ê If the CD does not start automatically, run the START.EXE file in the main directory of the CD.
Ê Select your system board or your device.
Ê Select Documentation.
Ê Select - Technical Manuals
Ê Select - Technical Manuals (BIOS)
You may have to install the Acrobat Reader - Software on the CD-ROM (path: utls/acrobat)
before reading!
i
For more details please read the according readme.txt files.
10 - English A26361-D1192-Z180-1-7619
Page 21
Installing drivers
Installing drivers
Ê Insert the "Drivers & Utilities" CD.
Ê If the CD doesn’t start automatically call the START.EXE file in the main directory of the CD.
Ê If the system board list is displayed select the system board or select under Driver the operating
system used and the audio and video drivers.
Upgrading main memory
Support: The system needs at least two modules and can manage at most four RDRAM
Size: From 128 Mbytes up to 2 Gbytes RDRAM
Technology: 184 Pin, 2.5V, 16/18Bit, PC800/PC600 RDRAM
Granularity: For two sockets 128, 129, 256, 512 Mbyte or 1 Gbyte
You must not combine memory modules from different manufacturer, different types of modules, or
modules of different capacities in the same bank. Different memory capacities are permitted in the
various banks. Example: 2 x 128 MB in bank 0 and 2 x 64 MB in bank 1 are permissible; 64 MB + 128
MB in bank 0 are not permissible.
!
Technology Memory Number of RDRAM
[Mbit] [Mbyte] [Mbyte] [Mbyte]
64 64 64 72 8
128 64 64 72 4
256 128 128 144 4
modules.
8M, 16M and 32M x 64Bit
8M, 16M and 32M x 72Bit (with ECC)
All locations must always be occupied. Missing memory modules must be replaced with a
C-RIMM. This C-RIMM must then be installed in the order of the locations behind the RIMM:
Location bank 0 = RIMM
Location bank 1 = C-RIMM.
Net memory Gross
memory
without ECC
128 128 144 16
128 128 144 8
256 256 288 16
256 256 288 8
512 512 576 16
Gross memory
with ECC
Chips per channel
A26361-D1192-Z180-1-7619 English - 11
Page 22
Troubleshooting
Troubleshooting
Message BIOS update
The System BIOS provides optimum support for the processor you have chosen. If the message
BIOS update for installed CPU failed
appears the microcode required for the processor inserted must still be loaded. Further information on
this is available in the "BIOS Setup" manual on the "Drivers & Utilities" CD provided.
The screen stays blank
If your screen stays blank this may have the following cause:
The wrong RAM memory module has been inserted
Ê See the chapter "Main Memory" for information which memory modules can be used.
ACPI S3 (Save-to-RAM) and/or ACPI S4 (Save-to-Disk) doesn’t work
This system board is fully compliant for ACPI S3 and S4. Therefore it is PC99 certified by Microsoft.
If you have any problems with ACPI please ensure that all of your components are supporting ACPI S3
and S4.
− Operating system
− Hardware and drivers of controllers (e. g. VGA, audio, LAN, SCSI controllers).
For further information please refer to http://developer.intel.com/technology/iapc/involve.htm .
12 - English A26361-D1192-Z180-1-7619
Loading...