Fujitsu Client Computing WB0045 Users Manual

FCC ID: EJE-WB0045 (IC: 337J-WB0045) Report No. M061025_Cert_AR5BXB6_NII_BT
EMC Technologies Report Number: M061025_Cert_AR5BXB6_NII_BT
FUJITSU NOTEBOOK USER MANUAL (part 2)
EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia
www.emctech.com.au
P7120.book Page 48 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Series Notebook - Section Five
Before Using the Wireless LAN
This manual describes the procedures required to prop­erly set up and configure the optional integrated Wire­less LAN Mini-PCI device (referred to as "WLAN”). Before using the WLAN device, read this manual care­fully to ensure it's correct operation. Keep this manual in a safe place for future reference.
Prior to using the wireless LAN device, be sure to run the Click Me! utility, as detailed in “Installing Click Me!” on page 26.
Wireless LAN Devices Covered by this Document
This document is applicable to systems containing one of the following devices. Most of the procedures are identical. Sections that differ between the devices have been noted in the text:
Intel PRO/Wireless 3945ABG
Network Connections
(WM3945ABG)
Atheros AR5006EXS Mini-Card Wireless network
card (AR5BXB6)
Characteristics of the WLAN Device
The WLAN device is a Mini-PCI card attached to the main board of the mobile computer.
The WLAN devices operate in license-free RF bands, therefore eliminating the need to procure an FCC license to operate. The WLAN devices operate in the
2.4GHz Industrial, Scientific, and Medical (ISM) RF band and in the lower and middle bands of the 5GHz Unlicensed National Information Infrastructure (UNII) bands.
The WLAN devices are capable of three operating modes, IEEE802.11a, IEEE802.11b and IEEE802.11g.
Encoding of data is modulated using Direct Sequence Spread Spectrum (DSSS) and Complementary Code Keying (CCK) when the WLAN device is operating in IEEE 802.11b mode and Orthogonal Frequency Divi­sion Multiplexing (OFDM) when operating in IEEE802.11a or IEEE802.11g mode.
The WLAN device is Wi-Fi certified and operates at the maximum data transfer rate of 54 Mbps in IEEE802.11a or IEEE802.11g mode and 11 Mbps in IEEE802.11b mode.
The maximum communication range indoors is approximately 80 feet (25 meters). However, that range will increase or decrease depending on factors such as number of walls, reflective material, or inter­ference from external RF sources.
The WLAN device supports the following encryption methods - WEP, CKIP, TKIP, and AES encryption.
WIRELESS LAN MODES USING THIS DEVICE
Ad Hoc Mode
(See Figure 5-1)
"Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks. Ad Hoc networks are an easy and inexpensive method for establishing network connectivity between multiple computers.
Ad Hoc mode requires that the SSID, network authenti­cation, and encryption key settings are identically configured on all computers in the Ad Hoc network.
Figure 5-1. Ad Hoc Mode Network
48
P7120.book Page 49 Monday, October 10, 2005 4:38 PM
WIreless LAN User’s Guide
Access Point (Infrastructure) Mode
(See Figure 5-2)
Infrastructure mode refers to a wireless network archi­tecture in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or can communicate with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the wired LAN in order to access computers, devices, and services such as file servers, printers, and databases.
How to Handle This Device
The WLAN device comes pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The Oper­ating System that your mobile computer comes with has been pre-configured to support the WLAN device.
WIRELESS NETWORK CONSIDERATIONS
The Intel PRO/Wireless 2915ABG and Atheros AR5002X WLAN devices support IEEE802.11a, IEEE802.11b and IEEE802.11g.
The WLAN devices operate in the 2.4GHz ISM band and the 5 GHz lower, middle, and upper UNII bands.
The maximum range of the WLAN device indoors is typically 80 feet (25 meters). Please note that the max­imum range you achieve may be shorter or longer than 80 feet, depending on factors such as access point
transmit power, number and density of obstructions, or external RF interference.
Microwave ovens will interfere with the operation of WLAN device as microwave ovens operate in the same
2.4GHz frequency range that IEEE802.11b/g devices operate in. Interference by microwaves does not occur with IEEE802.11a radio which operates in the 5 GHz RF band.
Wireless devices that transmit in the 2.4GHz fre­quency range may interfere with the operation of WLAN devices in IEEE802.11b/g modes. Symptoms of interference include reduced throughput, intermittent disconnects, and large amounts of frame errors. It is HIGHLY recommended that these interfering devices be powered off to ensure the proper operation of the WLAN device.
DEACTIVATING THE WLAN DEVICE
Deactivation of the WLAN device may be desired in certain circumstances (to extend battery life) or where certain environments require it (i.e. hospitals, clinics, airplanes, etc.). Fujitsu mobile computers employ two methods with which to deactivate the WLAN device:
Using the Wireless On/Off Switch
In Windows, using the Intel PROSet Software or
Atheros Client Utility software.
Figure 5-2. Access Point (Infrastructure) Mode Network
Internet
ADSL modem, cable modem, or similar
Wireless LAN
Wired LAN
Access Point*
*An optional hub for a wired LAN may be required depending upon the type of access point used.
49
P7120.book Page 50 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Series Notebook - Section Five
Deactivation using the Wireless On/Off Switch
The WLAN device can be deactivated quickly and effi­ciently by toggling the Wireless On/Off Switch to the Off position. (Figure 5-3)
The Wireless On/Off switch has no effect on non-Wire­less LAN models.
Wireless LAN On/Off Switch
Figure 5-3. Wireless LAN On/Off Switch Location
Deactivation using the Intel PROSet Software
The WLAN device can also be deactivated in Windows using the Intel PROSet Software. The procedure to accomplish this:
1. Click [Start]-> [All Programs].
2. Select Intel ProSet Wireless, then click on Intel ProSet Wireless from the menu that appears. The Intel ProSet Wireless utility will be displayed.
3. At the bottom left corner of the window, select Wireless Off from the dropdown list.
Deactivation using Atheros Client Utility software
1. Right-click on Atheros Client Utility icon in the system tray. Select “Open Atheros Client Utility” from the menu.
2. Choose Action and click Disable Radio.
ACTIVATING THE WLAN DEVICE
Activation of the WLAN device can be accomplished using the same methods as the deactivation process
Using the Wireless On/Off Switch
In Windows using the Intel PROSet Software or Atheros Software
50
P7120.book Page 51 Monday, October 10, 2005 4:38 PM
Configuration of the WLAN Device
WIreless LAN User’s Guide
The WLAN Device can be configured to establish wire­less network connectivity using one of the following tools:
Intel PROSet Software - The Intel PROSet Software allows for multiple profile setup and supports auto­matic profile switching. Support for most industry standard security solutions is contained in this soft­ware.
Atheros Client Utility - The Atheros Client Utility soft­ware allows for multiple profile setups and supports automatic profile switching. Support for most indus­try standard security solutions is contained in this software.
FLOW OF OPERATIONS
1. Activate the WLAN Device (See Activating the WLAN Device on page 50 for more information).
2. Configure the Wireless Network parameters (See Configure Wireless Network Parameters on page 51 for more information).
Enter the network name (SSID)
Choose the appropriate WLAN architecture (Ad Hoc or Infrastructure)
Choose Authentication method: Open, Shared, WPA-Enterprise, WPA2-Enterprise, WPA­Personal, or WPA2-Personal
If using static WEP keys, enter static WEP key and choose key index.
3. Configure network settings (See Configure Net­work Parameters on page 51 for more information)
TCP/IP settings
Workgroup or Domain settings.
CONFIGURATION USING INTEL PROSET SOFTWARE
This section explains the procedure to properly configure the WLAN device using the Intel PROSet Soft­ware. Pre-defined parameters will be required for this procedure. Please consult with your network adminis­trator for these parameters:
Network Name - Also known as the SSID
Network Key (WEP) - Required if using static WEP
keys.
Authentication Type - Open, Shared, WPA, or WPA­PSK
Procedure
1. Activate the WLAN device using either the Wireless On/Off Switch or the Intel PROSet software.
2. Click the [Start] button first and then [All Pro­grams].
3. Click the icon [Intel PROSet Wireless] to execute the Intel PROSet Wireless software.
4. Click the [Add] button. The General Settings dialog displays.
5. Enter a profile name in the Profile Name field.
6. Enter the network SSID, in the Network Name (SSID) field.
7. Click Infrastructure or Ad Hoc for the operating mode.
8. Click [Advanced].
9. The Mandatory Access Point option is only used if Infrastructure mode is selected. Use this option to connect to a specific access point. Enter the MAC address for the access point. Click OK to save the setting and return to the General Settings page.
10. Click [Next].
11. If you are using Cisco CCX, click Cisco Options to enable Cisco CKIP data encryption on the Security Settings page. Check the Cisco Compatible Exten­sions Options. If you have checked the Cisco's "Mixed-Cell" box in the Advanced Setting, this option must also be checked.
12. Click [OK].
13. Click Next.
14. Select Open, Shared, WPA-Enterprise, WPA2­Enterprise, WPA-Personal, or WPA2-Personal in the Network Authentication options.
15. Select either None, WEP, CKIP (if Enable Cisco Cli­ent eXtentions is enabled, use CKIP or WEP), or TKIP for the data encryption.
16. If WEP is selected, select either 64 or 128-bit for the Encryption Level.
17. Select the key index 1, 2, 3 or 4.
18. Enter the WEP key if required. If your network does not employ a 802.1x/EAP security mechanism, please skip to step 24.
51
P7120.book Page 52 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Series Notebook - Section Five
19. Click the Enable 802.1x checkbox to enable the
802.1x security option. Please contact your network administrator if configuration of this setting is required.
20. Select the appropriate Authentication Type. Please contact your network administrator if configura­tion of this setting is required.
21. After selecting your authentication type, enter the user name, domain, and password of the user you have created on the authentication server. The user name and password do not have to be the same as name and password of your current Windows user login.
22. Click [OK] to save the settings.
23. From the Intel ProSet Wireless page, click the new profile name shown in the Profile List. Use the up and down arrows to position the priority of the new profile in the priority list.
24. Click the Connect button to connect to the net­work.
25. Click [Close] if you want to close the Intel(R) PROSet for Wireless window.
CONFIGURATION USING ATHEROS CLIENT UTILITY SOFTWARE
This section explains the procedure to properly configure the WLAN device using the Atheros Client Utility. Pre-defined parameters will be required for this procedure. Please consult with your network adminis­trator for these parameters:
Network Name - Also known as the SSID
Network Key (WEP) - Required if using static WEP
keys.
Authentication Type - Open, Shared, WPA, or WPA­PSK
Procedure
1. Activate the WLAN device using either the Wireless On/Off Switch or the Atheros Client Utility
2. Right-click on the “Atheros Client Utility” icon in the system tray, and select “Open Atheros Client Utility” from the menu.
3. From the Current Status page, click the Profile Management tab.
4. If this is your first time using this utility, highlight the profile [Default] and Click the [Modify] button, otherwise Click the [New] button. The General Set­tings dialog displays.
5. From the General page, enter a profile name in the Profile Name field.
6. Enter the network SSID, in the SSID1 field. If you wish to create a profile that can connect to up to 3 different wireless networks, SSID's can be entered in the SSID2 and SSID3 fields as well.
7. Click the Security tab.
8. The Security tab allows for the configuration of the Security modes listed in the table below. Please select the radio button of the desired security mode. If these settings are not known to you, please consult with your network administrator for the correct settings.
Field Name Description
WPA Enables the use of Wi-Fi Protected
Access. Choosing WPA opens the WPA EAP drop-down menu. Options include TLS and PEAP. If these settings are not known to you, please consult with your network administrator for the correct settings.
WPA-PSK Enables WPA-Pre-Shared Key. Click
on the Configure button to enter the WPA Passphrase. If these settings are not known to you, please consult with your network administrator for the correct settings.
802.1x Enables 802.1x security. If these settings are not known to you, please consult with your network administrator for the correct settings. Choosing this option opens the
802.1x EAP type drop-down menu. Options include TLS, PEAP, and LEAP
Pre-Shared Key Enables the use of pre-shared keys
that are defined on both the access point and the station. This is where static WEP keys are entered. Click the Configure button to fill in the Define Pre-Shared Keys window.
None No security
9. Click OK
10. Click the Advanced tab
11. The Advanced tab allows for the configuration of the options detailed in the table below.
52
P7120.book Page 53 Monday, October 10, 2005 4:38 PM
WIreless LAN User’s Guide
.
Field Name Description
Power Save Mode
Network Type Options are AP (Infrastructure) or Ad
802.11b Preamble
Transmit Power Level
Wireless Mode Specifies 5 GHz 54 Mbps, 5 GHz 108
Wireless Mode when Starting Ad Hoc Network
Options are Maximum, Normal, or Off
Hoc
Specifies the preamble setting in
802.11b. The default setting is Short and Long (Access Point mode), which allows both short and long headers in the 802.11b frames. Set to Long Only to override allowing short frames.
Options are 100 mW, 63 mW, 50 mW, and 40 mW.
Mbps, 2.4 GHz 11 Mbps, or 2.4 GHz 54 Mbps operation in an access point network.
Specifies 5GHz 54 Mbps, 5 GHz 108 Mbps, 2.4 GHz 11 Mbps, or 2.4 GHz 54 Mbps to start an Ad Hoc network if no matching network name is found after scanning all available modes.
12. Click OK
13. If the profile you just created does not activate immediately, click the Profile Management tab, highlight the desired Profile, and click Activate.
14. Click [Close] if you want to close the Atheros Client Utility.
CONNECTION TO THE NETWORK
This section explains connection to the network.
2. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed.)
3. Double-click [Network Connections]. A list of cur­rently installed networks will be displayed.
4. Right-click [Wireless Network Connection] in the list, and then click [Properties] in the menu dis­played. The [Wireless Network Connection Proper­ties] window will be displayed.
5. Click the [General] tab if it is not already selected.
6. Click [Internet Protocol (TCP/IP] and then click [Properties]. The [Internet Protocol (TCP/IP) Properties] window will be displayed.
7. Set the IP address as follows:
For ad hoc connection: Select [Use the following IP address:] and then enter data for [IP address] and [Subnet mask]. See page 60 for IP address setting.
For access point (infrastructure) connection: If your network uses DHCP, select [Obtain an IP address automatically] and [Obtain DNS server address automatically]. If your network uses static IP addresses, consult with your network adminis­trator for the correct IP address settings.
8. Click the [OK] button. Processing will return to the
[Wireless Network Connection Properties] window.
9. Click the [OK] button.
10. Close the [Network Connection] window.
Following this operation, confirm the names of the
computer and the workgroup as follows.
If there is an administrator of the network, contact the network administrator for data settings.
Setting the network
Perform the “Setting TCP/IP” and “Confirming the computer and work group names” operations required for network connection.
Setting TCP/IP
To change the setting of the IP address, you need to be logged in from Windows as an administrator.
1. Click the [Start] button first and then [Control Panel].
Confirming the computer and work group names
To modify the computer name and/or the work group name, you need to be logged in from Windows as an administrator.
1. Click the [Start] button, then [Control Panel].
2. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed.)
3. Double-click the [System] icon. The [System Prop­erties] window will be displayed.
4. Click the [Computer Name] tab.
53
P7120.book Page 54 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Series Notebook - Section Five
5. Confirm the settings of [Full computer name:] and [Workgroup:].
a. The setting of [Full computer name:] denotes the
name for identifying the computer. Any name can be assigned for each personal computer.
To change the name, click [Change] and then proceed in accordance with the instruction messages displayed on the screen.
Enter the desired name in less than 15 ASCII character code format. Identifiability can be enhanced by entering the model number, the user name, and other factors.
b. [Workgroup name] is the group name of the
network. Enter the desired name in less than 15 ASCII character code format.
For ad hoc connection: Assign the same network name to all personal computers existing on the network.
For access point (infrastructure) connection:
Assign the name of the work group to be accessed.
3. Double-click [Network Connections]. A list of cur­rently installed networks will be displayed.
4. Right-click [Wireless Network Connection] in the list, and then click [Properties] in the menu dis­played. The [Wireless Network Connection Proper­ties] window will be displayed.
5. If [File and Printer Sharing for Microsoft Net- works] is displayed, proceed to step 6. If [File and Printer Sharing for Microsoft Networks] is not dis­played, skip to step 7.
6. Make sure that the [File and Printer Sharing for Microsoft Networks] check box is checked, and then click the [OK] button. Skip to “Setting file­sharing function”.
7. Click [Install]. The [Select Network Component Type] window will be displayed.
8. Click [Service], then click the [Add] button. The [Select Network Service] window will be displayed.
9. Click [File and Printer Sharing for Microsoft Net­works] and then click the [OK] button. Processing will return to the [Wireless Network Connection Properties] window, and [File and Printer Sharing for Microsoft Networks] will be added to the list.
6. Click the [OK] button. If a message is displayed that requests you to restart the personal computer, click [Yes] to restart the computer.
Setting the sharing function
Set the sharing function to make file and/or printer sharing with other network-connected personal computers valid.
This operation is not required unless the sharing func­tion is to be used.
The folder and printer for which the sharing function has been set will be usable from any personal computer present on the network.
To share a file and/or the connected printer, you need to be logged in as an administrator.
Setting the Microsoft network-sharing service
1. Click the [Start] button first and then [Control Panel].
2. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed.)
10. Click the [Close] button.
Setting the file-sharing function
The procedure for setting the file-sharing function follows, with the “work” folder in drive C: as an example.
1. Click the [Start] button first and then [My Com­puter].
2. Double-click [Local disk (C:)].
3. Right-click the “work” folder (or whichever folder
you want to share), and then click [Sharing and Security...] in the menu displayed. The [Folder
Name Properties] window will be displayed.
Setting the file-sharing function for the file which has been used to execute Network Setup Wizard is suggested on the screen. For the wireless LAN, however, since security is guaranteed by entry of the network name (SSID) and the network key, the steps to be taken to set the file­sharing function easily without using Network Setup Wizard are given below.
4. Click [Sharing] if it isn’t already selected.
54
P7120.book Page 55 Monday, October 10, 2005 4:38 PM
WIreless LAN User’s Guide
5. Click the link stating “If you understand the secu­rity risks, but want to share files without running the wizard, click here”.
6. Click “Just enable file sharing” and click [OK].
7. Check the [Share this folder on the network] check
box.
To specify the corresponding folder as a read-only folder, select the [Read only] checkbox under the General tab.
8. Click the [OK] button. The folder will be set as a sharable folder, and the display of the icon for the “work.” folder will change.
Setting the printer-sharing function
1. Click the [Start] button first and then [Printers and FAX]. A list of connected printers will be displayed.
2. Right-click the printer for which the sharing func­tion is to be set, and then click [Sharing] in the menu displayed. The property window correspond-
ing to the selected printer will be displayed.
Setting the printer-sharing function when Network Setup Wizard has been executed is suggested on the screen. For the wireless LAN, however, since security is guaranteed by entry of the network name (SSID) and the network key, the steps to be taken to set the printer-sharing function without using Network Setup Wizard are laid down below.
3. Click the [Sharing] tab.
4. Click [Share this printer].
5. Enter the sharing printer name in [Share name].
6. Click the [OK] button.
Confirming connection
After you have finished the network setup operations, access the folder whose sharing has been set for other personal computers. Also, confirm the status of the radio waves in case of trouble such as a network connection failure.
In the case of access point (infrastructure) connection, enter the necessary data for the access point before confirming connection. Refer to the manual of the access point for the access point setup procedure.
Connecting your personal computer to another personal computer
1. Click [Start] first and then [My Computer]. The [My Computer] window will be displayed in the left frame.
2. Click [My Network Places] in the “Other Places” list. The window [My Network Places] will be dis­played.
3. Click [View workgroup computers] under Network Tasks in the left frame.
4. Double-click the personal computer to which your personal computer is to be connected. The folder that was specified in “Setting the file-sharing func­tion” on page 54 will be displayed.
5. Double-click the folder to be accessed.
Confirming the status of the radio
1. Right-click the Intel PRO Wireless icon in the lower right corner of the screen.
2. Click [Open Intel PROSet for Wireless]. The Intel PROSet for Wireless window opens.
3. Contained within the General tab and the Details section (accessed by pressing the [Details] button), you will find the current operating status of the radio. (When the radio is turned off or the com­puter is not yet connected, some of the conditions will not be displayed.)
Profile Name
The current configuration profile is displayed.
Network Name (SSID)
Displays the Network Name (SSID) currently used by the radio.
IP Address
The IP address of the current profile.
Signal Quality
Displays a message stating the current quality of the signal.
Signal Strength
Displays a graphic representation of the current signal strength.
Additionally, in the lower section of the display, you will see a variety of different measurements related to the WLAN. For additional information about the items, click on the “Help?” button:
Adapter MAC Address
Band
Supported Data Rates
55
P7120.book Page 56 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Series Notebook - Section Five
Radio Frequency
Channel Number
Network Authentication
Data Encryption
802.1x Authentication Type
802.1x Authentication Protocol
CCX Version
CCX TPC
CCX Power Levels
Access Point MAC Address
Mandatory Access Point
56
P7120.book Page 57 Monday, October 10, 2005 4:38 PM
WIreless LAN User’s Guide
Troubleshooting
Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table.
Problem Possible Cause Possible Solution
Unavailable network connection
Incorrect network name (SSID) or network key
Weak received signal strength and/or link quality
The WLAN device has been deactivated or disabled
The computer to be connected is turned off
RF interference from Access Points or other wireless networks
Ad hoc connection: verify that the network names (SSID’s) and network
keys (WEP) of all computers to be connected have been configured correctly. SSID’s and WEP key values must be identical on each machine.
Access Point (Infrastructure) connection: set the network name (SSID) and network key to the same values as those of the access point.
Set the Network Authentication value identically to that of the Access Point. Please consult your network administrator for this value, if necessary.
For the method of setting network authentication, refer to the following page:·”Assigning parameters” on page 51·
Ad hoc connection: Retry connection after shortening the distance to the destination computer or removing any obstacles for better sight.
Access Point (Infrastructure) connection: Retry connection after short­ening the distance to the access point or removing any obstacles for better sight.
To check the wave condition, refer to the following page:· “Confirming the status of the radio waves” on page 55.
Check if the wireless switch is turned ON. Also verify “Disable Radio” is not checked in “Network setting” window. Refer to “Starting Transmis­sion” on page 50.
Check if the computer to be connected is turned ON.
The use of identical or overlapping RF channels can cause interference with the operation of the WLAN device. Change the channel of your Access Point to a channel that does not overlap with the interfering device.
Wireless network authentication has failed
Incorrectly configured network settings
Incorrect IP address configuration
Re-check your Network Authentication, Encryption, and Security settings. Incorrectly configured security settings such as an incorrectly typed WEP key, a mis-configured LEAP username, or an incorrectly chosen authentication method will cause the LAN device to associate but not authenticate to the wireless network.
Recheck the configuration of your network settings.
For the method of checking, refer to the following page:·“Connection to the Network” on page 53.
This only applies to networks using static IP addresses. Please contact your network administrator for the correct settings.
57
P7120.book Page 58 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Series Notebook - Section Five
Wireless LAN Glossary
Ad Hoc Mode
Ad Hoc Mode refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Points. Connectivity is accomplished using only client devices in a peer-to-peer fashion. For details, refer to “Ad hoc connection” on page 48.
Channel
Range of narrow-band frequencies used by the WLAN device to transmit data. IEEE802.11b/g - 11 channels, 22 MHz wide channels.
DHCP (Dynamic Host Configuration Protocol)
A protocol that provides a means to dynamically allocate IP addresses to computers on a local area network.
DNS (Domain Name System)
A data query service that provides a mechanism with which to translate host names into Internet addresses.
IEEE802.11a
Wireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11a devices operate in the 5 GHz lower and middle UNII bands.
IEEE802.11b
Wireless LAN standard that supports a maximum data rate of 11 Mbps. 802.11b devices operate in the 2.4 GHz ISM band.
Access point
Wireless network device used to bridge wireless and wired network traffic.
IP address
The logical 32-bit host address defined by the Internet Protocol that uniquely identifies a computer on a network. The IP address is usually expressed in dotted decimal notation.
LAN (Local Area Network)
A LAN or Local Area Network is a computer network (or data communications network) which is confined to a limited geographical area.
MAC address (Media Access Control Address)
A MAC address (also called an Ethernet address or IEEE MAC address) is the 48-bit address (typically written as twelve hexadecimal digits, 0 through 9 and A through F, or as six hexadecimal numbers separated by periods or colons, e.g., 0080002012ef, 0:80:0:2:20:ef) which uniquely identifies a computer that has an Ethernet interface.
MTU (Maximum Transmission Unit)
The maximum size of data which can be transmitted at one time in networks including the Internet. In an envi­ronment whose maximum size of data is too large to correctly receive data, normal communications can be restored by setting the size of MTU to a smaller value.
Network key
Data that is used for encrypting data in data communi­cation. The personal computer uses the same network key both for data encryption and decryption, therefore, it is necessary to set the same network key as the other side of communication.
Network name (SSID: Security Set Identifier)
When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. This grouping is performed with “Network name (SSID)”. In order to improve security, the network key is set allowing no communication unless “Network name (SSID)” coincides with the network key.
Open system authentication
Null authentication method specified in the 802.11 stan­dard that performs no authentication checks on a wire­less client before allowing it to associate.
PPPoE (Point to Point Protocol over Ethernet)
A method of allowing the authentication protocol adopted in telephone line connection (PPP) to be used over an Ethernet.
Protocol
A procedure or rule of delivering data among computers. Ordered data communication is allowed by making all conditions required for communication including the method of data transmission/reception and actions upon communication errors into proce­dures.
58
P7120.book Page 59 Monday, October 10, 2005 4:38 PM
Shared key authentication
802.11 network authentication method in which the AP sends the client device a challenge text packet that the client must then encrypt with the correct WEP key and return to the AP. If the client has the wrong key or no key, authentication will fail and the client will not be allowed to associate with the AP. Shared key authentica­tion is not considered secure, because a hacker who detects both the clear-text challenge and the same chal­lenge encrypted with a WEP key can decipher the WEP key.
SSID (Service Set Identifier)
Service Set Identifier, a 32-character unique identifier attached to the header of packets sent over a WLAN that acts as a password when a mobile device tries to connect to the BSS. The SSID differentiates one WLAN from another, so all access points and all devices attempting to connect to a specific WLAN must use the same SSID. A device will not be permitted to join the BSS unless it can provide the unique SSID. Because the SSID is broadcast in plain text, it does not supply any security to the network.
Subnet mask
WIreless LAN User’s Guide
TCP-IP network is controlled by being divided into multiple smaller networks (subnets). IP address consists of the subnet address and the address of each computer. Subnet mask defines how many bits of IP address comprise the subnet address. The same value shall be set among computers communicating with each other.
TCP/IP (Transmission Control Protocol/Internet Protocol)
A standard protocol of the Internet.
Wi-Fi
Wi-Fi, or Wireless Fidelity, is a set of standards for wire­less local area networks (WLAN) based on the IEEE
802.11 specifications. Certified products can use the official Wi-Fi logo, which indicates that the product is interoperable with any other product also showing that logo.
59
P7120.book Page 60 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Series Notebook - Section Five
IP address information
IP addressing is much more complicated than can be briefly explained in this document. You are advised to consult with your network administrator for additional information.
If IP address is unknown, set IP address as follows:
If you have an access point (DHCP server) on the network, set the IP address as follows:
[Obtain an IP address automatically]
A DHCP server is a server that automatically assigns IP addresses to computers or other devices in the network. There is no DHCP server for the AdHoc network.
If the IP address is already assigned to the computer in the network, ask the network administrator to check the IP address to be set for the computer.
If no access point is found in the network:
An IP address is expressed with four values in the range between 1 and 255.
Set the each computer as follows: The value in paren­theses is a subnet mask.
<Example>
Computer A: 192.168.100.2 (255.255.255.0)
Computer B: 192.168.100.3 (255.255.255.0)
Computer C: 192.168.100.4 (255.255.255.0)
:
:
Computer X: 192.168.100.254 (255.255.255.0)
60
P7120.book Page 61 Monday, October 10, 2005 4:38 PM
WIreless LAN User’s Guide
Specifications
Item Specification
Type of network The Atheros AR5002X and the Intel PRO/Wireless 2915ABG
Network Connections WLAN devices conform to IEEE 802.11a and 802.11b/g (Wi-Fi based)*.
Transfer rate (Automatic switching)
IEEE 802.11a/g: 54 Mbps maximum data rate
IEEE 802.11b: 11 Mbps maximum data rate
Active frequency 802.11b/g: 2400~2473 MHz
802.11a: 4900 ~ 5850 MHz
Number of channels 802.11a: 8 independent channels
Security Encryption Types - CKIP, WEP, TKIP, AES**
Maximum recommended number of computers to be connected over wireless LAN (during ad hoc connection)
802.11b/g: 11 channels, 3 non-overlapping channels
WPA 1.0 compliant
Encryption Key lengths Supported: 64 bits, 128 bits, and 152 bits (Atheros module using AES encryption only)
802.1x/EAP
10 units or less ***
* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed.
** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/ 104 bits after subtracting the fixed length of 24 bits.
*** Depending on practical environments, the allowable number of computers to be connected may be decreased.
61
P7120.book Page 62 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Series Notebook - Section Five
Using the Bluetooth Device
The Integrated Bluetooth module (EYTF3CSFT) is an optional device available for Fujitsu mobile computers.
WHAT IS BLUETOOTH
Bluetooth technology is designed as a short-range wire­less link between mobile devices, such as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create Personal Area Networks (PANs) between devices in short-range of each other.
The Wireless LAN/Bluetooth On/Off Switch will power off both the optional wireless LAN and Bluetooth devices at the same time. To enable or disable either one of the devices individually, perform the following steps:
1. Slide the Wireless LAN/Bluetooth on/ off switch to On position.
2. In the Control Panel, double-click the Fujitsu Radio Control icon.
3. In the window that appears, click the button associated with Bluetooth and/ or Wireless LAN Status to enable or dis­able the individual devices.
4. Click [OK].
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
The transmitters in this device must not be co-located or operated in conjunction with any other antenna or transmitter.
Canadian Notice
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
Warranty
Users are not authorized to modify this product. Any modifications invalidate the warranty.
This equipment may not be modified, altered, or changed in any way without signed written permission from Fujitsu. Unauthorized modification will void the equipment authorization from the FCC and Industry Canada and the warranty.
WHERE TO FIND INFORMATION ABOUT BLUETOOTH
The Bluetooth module contains a robust Help user’s guide to assist you in learning about operation of the Bluetooth device.
To access the Help file, click [Start] -> All Programs, and click on Toshiba. Select Bluetooth, then select User’s Guide.
For additional information about Bluetooth Technology, visit the Bluetooth Web site at: www.bluetooth.com.
62
P7120.book Page 63 Monday, October 10, 2005 4:38 PM
Troubleshooting
6
63
P7120.book Page 64 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Six
64
P7120.book Page 65 Monday, October 10, 2005 4:38 PM
Troubleshooting
Your Fujitsu LifeBook notebook is sturdy and subject to few problems in the field. However, you may encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices, that you can solve by replacing the device. The information in this section helps you isolate and resolve some of these straightforward problems and identify failures that require service.
IDENTIFYING THE PROBLEM
If you encounter a problem, go through the following procedure before pursuing complex troubleshooting:
1. Turn off your LifeBook notebook.
2. Make sure the AC adapter is plugged into your note­book and to an active AC power source.
3. Make sure that any card inserted in the PC Card slot is seated properly. You can also remove the card from the slot, thus eliminating it as a possible cause of failure.
4. Make sure that any devices connected to the external connectors are plugged in properly. You can also disconnect such devices, thus eliminating them as possible causes of failure.
5. Turn on your notebook. Make sure it has been off at least 10 seconds before you turn it back on.
6. Go through the boot sequence.
7. If the problem has not been resolved, refer to the Troubleshooting Table, that follows, for more detailed troubleshooting information.
8. If you are still having problems after referring to the Troubleshooting Table, go to the Fujitsu Computer Systems Support website (http://www.computers.us .fujitsu.com/support), and search the list of Frequently Asked Questions (FAQs) contained there.
Troubleshooting
If you keep notes about what you have tried, your support representative may be able to help you more quickly by giving additional suggestions over the phone.
9. If you have tried the solutions suggested above without success, contact your support representative:
Toll free: 1-800-8Fujitsu (1-800-838-5487) Fax: 408-764-2724 E-mail: 8fujitsu@us.fujitsu.com Web site: http://www.computers.us.fujitsu.com/support
Before you place the call, you should have the following information ready so that the customer support represen­tative can provide you with the fastest possible solution:
Product name
Product configuration number
Product serial number
Purchase date
Conditions under which the problem occurred
Any error messages that have occurred
Type of device connected, if any
See the Configuration Label on the bottom of your notebook for configuration and serial numbers.
SPECIFIC PROBLEMS
Using the Troubleshooting Table
When you have problems with your LifeBook notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your notebook.
65
P7120.book Page 66 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Six
TROU B LES H O OTI N G TAB L E
Problem Page
Audio Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 66
Optical Drive Problems . . . . . . . . . . . . . . . . . . . . page 66
Floppy Disk Drive Problems . . . . . . . . . . . . . . . . page 67
Hard Drive Problems . . . . . . . . . . . . . . . . . . . . . . page 67
Keyboard or Mouse Problems. . . . . . . . . . . . . . . page 67
Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . page 68
Modem Problems. . . . . . . . . . . . . . . . . . . . . . . . . page 68
Problem Possible Cause Possible Solutions
Audio Problems
There is no sound coming from the built-in speakers.
The software volume control is set too low.
Headphones are plugged into your notebook.
BIOS audio settings are incorrect.
Software driver is not config­ured correctly.
Problem Page
USB Device Problems . . . . . . . . . . . . . . . . . . . . . page 68
PC Card Problems . . . . . . . . . . . . . . . . . . . . . . . . page 68
Power Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . page 69
Shutdown and Startup Problems . . . . . . . . . . . . page 70
Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 71
Miscellaneous Problems . . . . . . . . . . . . . . . . . . . page 72
Adjust the sound volume control settings in your software, operating system and applications. You can also use the [Fn+F9] key combination. Pressing [F9] repeatedly while holding [Fn] will increase the notebook volume.
Plugging in headphones disables the built-in speakers; remove the headphones.
Set the BIOS setup utility to the default values within the Multimedia Device Configuration menu. (See BIOS Setup
Utility on page 25 for more information)
Refer to your application and operating system documen­tation for help.
Sound may be set to Mute. Click on the Volume icon in the system tray and verify that
Device Manager may not be set correctly.
DVD/CD-RW Drive Problems
LifeBook notebook fails to recognize disc in optical drive.
Protective sheet is still in the optical drive tray.
The disc is not pushed down onto the center of the drive.
Optical drive tray is not latched shut.
Incorrect DVD Player or no player software is installed.
Wrong drive designator was used for optical drive in the application.
the Mute checkbox is not set. You can also use the [Fn+F3] key combination. Pressing [F3] while holding [Fn] will toggle the audio Mute on and off.
Go to the Control Panel -> System, and click on the Hard­ware tab. Click the [Device Manager] button and scroll down to “Sound, Video and Game Controllers”. Click the “+” symbol and scroll down the list that appears to see if there is a yellow exclamation point next to any of the items. If there is, you will need to reload the related driver.
Remove the protective sheet from the tray.
Open optical drive tray and re-install the disc properly.
Push on the front of the optical drive tray until it latches.
Install DVD Player software. (See “Using the Optical Drive
Software” on page 35 for more information.)
Verify the drive designator used by the application is the same as the one used by the operating system. When the operating system is booted from a DVD/CD, drive designa­tions are automatically adjusted.
DVD/CD disc is dirty or defective.
66
Wipe disc with non-abrasive cleaning cloth and reinsert. If it still will not work try a different disc.
P7120.book Page 67 Monday, October 10, 2005 4:38 PM
Problem Possible Cause Possible Solutions
The Optical Drive Access indicator on the Status Indicator Panel blinks at regular
The Windows auto insertion function is active and is checking to see if a disc is
ready to run. intervals when no disc is in the tray or the drive is not installed.
Floppy Disk Drive Problems
Troubleshooting
This is normal. However, you may disable this feature. (See Auto Insert Notification Function on page 36 for more infor­mation)
You cannot access your optional floppy disk.
You tried to write to a write
protected floppy disk.
Floppy disk is not loaded
correctly.
Security is set to protect
access to floppy disk data.
Hard Drive Problems
You cannot access your hard drive.
The setup utility is incor-
rectly set for your internal
(Primary Master) or optional
second hard drive (Primary
Slave).
The wrong drive designator
was used by an application
when a bootable CD-ROM
was used to start the note-
book.
Security is set so your oper-
ating system cannot be
started without a password.
Keyboard or Mouse Problems
The built-in keyboard does not seem to work.
The notebook has gone into
Suspend mode.
Your application has locked
out your keyboard.
The characters that
NumLk is set in the BIOS. Go to the BIOS and make sure that NumLk is disabled. (See appear do not match those which you typed.
Eject the floppy disk and set it to write enable. (See
Preparing a Disk for Use on page 33 for more information)
Eject floppy disk, check orientation and re-insert. (See Ejecting a Disk on page 33 for more information)
Verify your password and security settings.
Revise BIOS settings to set both Primary Master and Primary Slave correctly. (See BIOS Setup Utility on page 25
for more information)
Verify drive designator used by application is in use by the operating system. When the operating system is booted from a CD, drive designations are automatically adjusted.
Verify your password and security settings.
Push the Suspend/Resume/Power On button.
Try to use your integrated pointing device to restart your system. If this fails, turn your notebook off by pressing the Power/Suspend/Resume button for several seconds. After the system has been off for at least 10 seconds, turn it back on.
BIOS Setup Utility on page 25 for more information)
You have installed an external keyboard or mouse, and it does not seem to work.
Your external device is not
properly installed.
Your operating system soft-
ware is not setup with the
correct software driver for
that device.
Re-install your device. (See Device Ports on page 42 for more
information)
Check your device and operating system docu-mentation and activate the proper driver.
67
P7120.book Page 68 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Six
Problem Possible Cause Possible Solutions
You have connected an external keyboard or a mouse and it seems to be locking up the system.
Your operating system soft­ware is not setup with the correct software driver for that device.
Your system has crashed. Try to restart your notebook. If this fails, turn your note-
Memory Problems
Your Power On screen or Info menu of the BIOS setup utility information do not show the correct
Your memory upgrade module is not properly installed.
You have a memory failure. Check for Power On Self Test (POST) messages. (See Power
amount of memory.
Modem Problems
Check your device and operating system documentation and activate the proper driver.
book off by pressing the Power/Suspend/Resume button for several seconds. After the system has been off for at least 10 seconds, turn it back on.
Remove and re-install your memory upgrade module. (See
Memory Upgrade Module on page 40 for more information)
On Self Test Messages on page 73 for more information)
Messages about modem operation.
USB Device Problems
You have installed a USB device but your LifeBook notebook does not recognize the device, or the device does not seem to work properly.
PC Card Problems
Messages about modem operation are generated by whichever modem applica­tion is in use.
The USB port is not enabled in the BIOS.
The device is not properly installed.
The device may have been installed while an application was running, so the notebook is not aware of its installation.
Your software may not have the correct software driver active.
Yo u m ay ha ve th e w ro ng I/O address selected for your device.
Your device and another device are assigned the same I/O address.
See your application software documentation for addi­tional information.
Verify the USB port is set to Enabled in the BIOS. (See
BIOS Setup Utility on page 25 for more information)
Remove and re-install the device. (See Device Ports on page 42 for more information)
Close the application and restart your notebook.
See your software documentation and activate the correct driver.
See your device documentation and software documenta­tion to determine the required I/O address. Change the settings in the BIOS setup utility. (See BIOS Setup Utility on
page 25 for more information)
Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.
Card inserted in the PC Card slot does not work or is locking up the system.
68
The card is not properly inserted.
Remove and re-insert the card. (See PC Cards on page 37 for
more information)
P7120.book Page 69 Monday, October 10, 2005 4:38 PM
Problem Possible Cause Possible Solutions
A card inserted in the PC Card slot does not work or is locking up the system.
(continued)
The card may have been
inserted while an application
was running, so your note-
book is not aware of its inser-
tion.
Your software may not have
the correct software driver
active.
Troubleshooting
Close the application and restart your notebook.
See your software documentation and activate the correct driver.
Power Failures
You turn on your notebook and nothing seems to happen.
You may have the wrong I/O
address selected for your PC
Card device.
Your PC Card device and
another device are assigned
the same I/O address.
The installed primary battery
is completely discharged,
there is no optional second
battery installed or there is no
Power adapter installed.
The primary battery is
installed but is faulty.
The battery or batteries are
low.
The adapter (AC or auto/
airline) is not plugged in
properly.
The Power adapter (AC or
auto/airline) has no power
from the AC outlet, airplane
seat jack, or the car’s cigarette
lighter.
See your PC Card documentation to determine the required I/O address. Change the settings in the BIOS. (See
BIOS Setup Utility on page 25 for more information)
Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.
Check the Status Indicator Panel to determine the presence and condition of the batteries. (See Status Indicator Panel on page 12 for more information) Install a charged battery or a Power adapter.
Use the Status Indicator panel to verify the presence and condition of the batteries. (See Status Indicator Panel on page 12 for more information) If a battery is indicating a short, remove that battery and operate from another power source or replace that battery.
Check the Status Indicator Panel to determine the presence and condition of the batteries. (See Status Indicator Panel on page 12 for more information) Use a Power adapter to operate until a battery is charged or install a charged battery.
Verify that your adapter is connected correctly. (See Power
Sources on page 23 for more information)
Move the AC cord to a different outlet, check for a line switch or tripped circuit breaker for the AC outlet. If you are using an auto/airline adapter in a car make sure the ignition switch is in the On or Accessories position.
Your LifeBook note­book turns off all by itself.
The Power adapter (AC or
auto/airline) is faulty.
The power management
parameters are set for auto
timeouts which are too short
for your operating needs.
Your power adapter has failed
or lost its power source.
Try a different Power adapter or install a charged optional second battery.
Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. Check your power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs.
Make sure the adapter is plugged in and the outlet has power.
69
P7120.book Page 70 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Six
Problem Possible Cause Possible Solutions
Your LifeBook note­book turns off all by itself.
(continued)
You are operating on battery power and have ignored a low battery alarm until the battery is at dead battery state and system has gone into Dead Battery Suspend mode.
You have a battery failure. Verify the condition of the batteries using the Status Indi-
Install a power adapter and then push the Suspend/Resume button. (See Power Sources on page 23 for more information)
cator panel, and replace or remove any batteries that are shorted. (See Status Indicator Panel on page 12 for more
information)
Your LifeBook note­book will not work on battery alone.
The installed batteries are dead.
No batteries are installed. Install a charged battery.
The batteries are improperly installed.
Your installed batteries are faulty.
The batteries seem to discharge too quickly.
You are running an applica­tion that uses a lot of power due to frequent hard drive or media drive access, or use of a modem or LAN PC card.
The power savings features may be disabled.
The brightness is turned all the way up.
The batteries are very old. Replace the batteries.
The batteries were exposed to high temperatures.
The batteries are too hot or too cold.
Shutdown and Startup Problems
The Suspend/Resume/ Power On button does not work.
Suspend/Resume/Power On button is disabled from the Power menu -> Advanced submenu of the setup utility.
Replace the battery with a charged one or install a Power adapter.
Verify that the batteries are properly connected by re­installing them.
Verify the condition of the batteries using the Status Indi­cator panel and replace or remove any batteries that are shorted. (See Status Indicator Panel on page 12 for more
information)
Use both the primary battery and an optional second battery and/or use a power adapter for this application when at all possible.
Check the power management and/or setup utility settings in the Power Savings menu and adjust according to your operating needs.
Turn down the brightness adjustment. The higher the brightness the more power your display uses.
Replace the batteries.
Restore the notebook to normal operating temperature. The Charging icon on the Status Indicator panel will flash when the battery is outside its operating range.
Enable the button from the setup utility.
You did not hold the button in long enough.
Hold the button longer. This may need to be a few seconds if your application is preventing the CPU from checking for button pushes.
There may be a conflict with
Close all applications and try the button again.
the application software.
70
P7120.book Page 71 Monday, October 10, 2005 4:38 PM
Problem Possible Cause Possible Solutions
The system powers up, and displays power on information, but fails
Boot sequence settings of the
setup utility are not compat-
ible with your configuration. to load the operating system.
You have a secured system
requiring a password to load
your operating system.
Internal hard drive was not
detected.
An error message is displayed on-screen
Power On Self Test (POST)
has detected a problem. during the notebook (boot) sequence.
Troubleshooting
Set the operating source by pressing [F12] while the Fujitsu logo is on screen or use the [F2] key and enter the setup utility and adjust the source settings from the Boot menu.
(See BIOS Setup Utility on page 25 for more information)
Make sure you have the right password. Enter the setup utility and verify the Security settings and modify them as accordingly. (See BIOS Setup Utility on page 25 for more
information)
Use the BIOS setup utility to try to auto detect the internal hard drive. If this does not work, contact Fujitsu Service and Support at 1-800-8FUJITSU.
See the Power On Self Test (POST) messages to determine the meaning and severity of the problem. Not all messages are errors; some are simply status indicators. (See Power On
Self Test Messages on page 73 for more information)
Your notebook appears to change setup parameters when you start it.
Video Problems
The built-in display is blank when you turn on your LifeBook notebook.
BIOS setup changes were not
saved when you made them
and exited the BIOS setup
utility returning it to
previous settings.
The BIOS CMOS hold-up
battery has failed.
The notebook is set for an
external monitor only.
The display angle and bright-
ness settings are not adequate
for your lighting conditions.
Power management timeouts
may be set for short intervals
and you failed to notice the
display come on and go off.
The notebook is set for S-
Video display only.
Make sure you select Save Changes And Exit when exiting the BIOS setup utility.
Contact your support representative for repairs. This is not a user serviceable part but has a normal life of 3 to 5 years.
Pressing [F10] while holding down the [Fn] key allows you to change your selection of where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order are: built­in display only, external monitor only, both built-in display and external monitor.
Move the display and the brightness control until you have adequate visibility.
Press any button the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. (The display may be shut off by Standby mode, Auto Suspend or Video Timeout)
While holding down the [Fn] key, click on the [F11] key to toggle the S-Video display off.
The notebook turned on with a series of beeps and your built­in display is blank.
The display goes blank by itself after you have been using it.
Power On Self Test (POST)
has detected a failure which
does not allow the display to
operate.
The notebook has gone into
Video timeout, or Standby,
Suspend, or Hibernation
modes because you have not
used it for a period of time.
Contact your support representative.
Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. Check your power management settings to adjust the timeout values to better suit your operation needs. (See
BIOS Setup Utility on page 25 for more information)
71
P7120.book Page 72 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Six
Problem Possible Cause Possible Solutions
The display goes blank by itself after you have been using it.
(continued)
The Built-in Display does not close.
The power management timeouts may be set for very short intervals and you failed to notice the display come on and go off.
A foreign object, such as a paper clip, is stuck between the display and the keyboard.
The Built-in Display has bright or dark spots.
If the spots are very tiny and few in number, this is normal for a large LCD display.
If the spots are numerous or large enough to interfere with your operation needs.
The application display uses only a portion of your screen and is surrounded by a dark frame.
The display is dark when on battery
You are running an applica­tion that does not support 800 x 600/1024 x 768 pixel resolution display and display compression is enabled.
The default is set on low brightness to conserve power.
power.
You have connected an external monitor
Your BIOS setup is not set to
enable your external monitor. and it does not display any information.
Your external monitor is not
properly installed.
Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. (The display may be shut off by Standby Mode, Auto Suspend or Video Timeout)
Remove all foreign objects from the keyboard.
This is normal; do nothing.
Display is faulty; contact your support representative.
Display compression gives a clearer but smaller display for applications that do not support 800 x 600/1024 x 768 pixel resolution. You can fill the screen but have less resolution by changing your display compression setting, (See the Video Features submenu, located within the Advanced menu of the BIOS. (See BIOS Setup Utility on page 25 for
more information)
Press [Fn] + [F7] to increase brightness and adjust Power Control under battery settings.
Toggle the video destination by pressing [Fn] and [F10] together, or check your BIOS setup and enable your external monitor. (See the Video Features submenu, located within the Advanced Menu of the BIOS. (See BIOS Setup Utility on
page 25 for more information)
Reinstall your device. (See External Video Port on page 44 for more information)
You connected an external monitor but it doesn’t come on.
Miscellaneous Problems
An error message is displayed on the screen during the operation of an application.
72
Your operating system soft-
ware is not setup with the
correct software driver for
that device.
Your external monitor is not
compatible with your Life-
Book notebook.
Application software often
has its own set of error
message displays.
Check your device and operating system documentation and activate the proper driver.
See your monitor documentation and the External Monitor Support portions of the Specifications section.
(See Specifications on page 85 for more information)
See your application manual and help displays screens for more information. Not all messages are errors some may simply be status.
P7120.book Page 73 Monday, October 10, 2005 4:38 PM
Troubleshooting
POWER ON SELF TEST MESSAGES
The following is an alphabetic list of error-and-status messages that the Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.
nnnn Cache SRAM Passed
Where nnnn is the amount of system cache in kilobytes success-fully tested by the Power On Self Test. (This can only appear if you have an SRAM PC Card inserted.)
*Diskette drive A error or Diskette drive B error
Drive A: or B: is present but fails the BIOS Power On Self Test diskette tests. Check to see that the drive is defined with the proper diskette type in the Setup Utility, (See BIOS Setup Utility on page 25 for more information) and that the diskette drive is installed correctly. If the disk drive is properly defined and installed, avoid using it and contact your support representative.
*Extended RAM Failed at offset: nnnn
Extended memory not working or not configured prop­erly. If you have an installed memory upgrade module, verify that the module is properly installed. If it is prop­erly installed, you may want to check your Windows Setup to be sure it is not using unavailable memory until you can contact your support representative.
nnnn Extended RAM Passed
Where nnnn is the amount of memory in kilobytes successfully tested.
*Failing Bits: nnnn The hex number nnnn
This is a map of the bits at the memory address (in System, Extended, or Shadow memory) which failed the memory test. Each 1 (one) in the map indicates a failed bit. This is a serious fault that may cause you to lose data if you continue. Contact your support representative.
*Fixed Disk x Failure or Fixed Disk Controller Failure (where x = 1-4)
The fixed disk is not working or not configured properly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue. Contact your support representative.
*Incorrect Drive A type – run SETUP
Type of floppy drive A: not correctly identified in Setup. This means that the floppy disk drive type identified in
your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.
*Incorrect Drive B type – run SETUP
Type of floppy drive B: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.
*Invalid NVRAM media type
Problem with NVRAM access. In the unlikely case that you see this message you may have some display prob­lems. You can continue operating but should contact your support representative for more information.
*Keyboard controller error
The keyboard controller test failed. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.
*Keyboard error
Keyboard not working. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.
*Keyboard error nn
BIOS discovered a stuck key and displays the scan code for the stuck key. You may have to replace your keyboard but may be able to use an external keyboard until then. Contact your support representative.
*Monitor type does not match CMOS – Run SETUP
Monitor type not correctly identified in Setup. This error probably means your BIOS is corrupted, run the setup utility and set all settings to the default conditions. If you still get this error, contact your support representative.
*Operating system not found
Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:. If the setup utility is correctly set, your hard drive may be corrupted and your system may have to be re-installed from your back up media.
*Parity Check 1 nnnn
Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data destroying failure. Contact your support representative.
73
P7120.book Page 74 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Six
*Parity Check 2 nnnn
Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data-destroying failure. Contact your support representative.
*Press <F1> to resume, <F2> to SETUP
Displayed after any recoverable error message. Press the [F1] key to continue the boot process or the [F2] key to enter Setup and change any settings.
*Previous boot incomplete – Default configuration used
Previous Power On Self Test did not complete success­fully. The Power On Self Test will load default values and offer to run Setup. If the previous failure was caused by incorrect values and they are not corrected, the next boot will likely fail also. If using the default settings does not allow you to complete a successful boot sequence, you should turn off the power and contact your support representative.
*Real time clock error
Real-time clock fails BIOS test. May require board repair. Contact your support representative.
*Shadow RAM Failed at offset: nnnn
Shadow RAM failed at offset nnnn of the 64k block at which the error was detected. You are risking data corrup­tion if you continue. Contact your support representative.
nnnn Shadow RAM Passed
Where nnnn is the amount of shadow RAM in kilobytes successfully tested.
*System battery is dead – Replace and run SETUP
The BIOS CMOS RAM memory hold up battery is dead. This is part of your BIOS and is a board mounted battery which requires a support representative to change. You can continue operating but you will have to use setup utility default values or reconfigure your setup utility every time you turn off your notebook. This battery has an expected life of 2 to 3 years.
System BIOS shadowed
System BIOS copied to shadow RAM.
*System CMOS checksum bad – run SETUP
BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. Run Setup and reconfigure the system.
*System RAM Failed at offset: nnnn
System memory failed at offset nnnn of in the 64k block at which the error was detected. This means that there is a fault in your built-in memory. If you continue to operate, you risk corrupting your data. Contact your support representative for repairs.
nnnn System RAM Passed
Where nnnn is the amount of system memory in kilobytes successfully tested.
*System timer error
The timer test failed. The main clock that operates the computer is faulty. Requires repair of system board. Contact your support representative for repairs.
UMB upper limit segment address: nnnn
Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager.
Video BIOS shadowed
Video BIOS successfully copied to shadow RAM.
EMERGENCY DVD TRAY RELEASE
If for some reason the eject button fails, you can open the DVD/CD-RW tray with a paper clip or similar tool inserted into the eject hole in the far right side of the front of the tray. Straighten one side of a paper clip and push it gently into the hole. The tray will pop out a short distance.
MODEM RESULT CODES
The operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem. The operating system and application software may suppress display of the result codes.
Examples of result codes are:
OK
NO CARRIER
NO DIALTONE
CONNECT 53000 (Connection complete at 53,000 bps.)
ERROR
FAX
RING (This means an incoming call.)
BUSY
NO ANSWER
When using the internal modem with applications that are not factory installed refer to the application documentation.
74
P7120.book Page 75 Monday, October 10, 2005 4:38 PM
Troubleshooting
Restoring Your Pre-installed Software
The Drivers and Applications Restore (DAR) CD contains sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your notebook configuration for use as documented below
If you have access to the internet, visit the Fujitsu Support web site at http:// www.computers.us.fujitsu.com/support to check for the most current information, drivers and hints on how to perform recovery and system updates.
Automatically Downloading Driver Updates on page 76 for more information)
Re-Installing Individual Drivers and Applications
The Drivers and Applications CD can be used to selec­tively re-install drivers and/or applications that may have
been un-installed or corrupted.
There may be certain free third-party applications pre-installed on your system that are not on the DAR CD. The latest versions of the applications can be downloaded from the third-party’s website.
To re-install drivers and/or applications:
1. Boot up the system and insert the DAR CD after Windows has started. A Fujitsu Installer screen is displayed after the CD is inserted.
2. After reading the License Agreement, click [I agree].
3. A window will appear containing a list of applica­tions, drivers, and utilities that you can install from the Drivers and Applications CD
The components listed are color-coded in terms of their install status. Blue indicates that the component can be installed. Green indicates that the component needs to be installed separately. Grey indicates a component that is already installed; grey items can be reinstalled, but prior to installation you will receive a reminder that the component is already installed.
4. In the list, check off all the components you want to install. If you want to install all components, click [Select All]. Clicking [Select All] will select all of the blue-coded components; you must select grey and green components separately.
5. Once you have selected the components you wish to install, click [Install Selected Subsystems]; the components will be installed.
.
(See
.
6. After the components are installed, click [OK], then click [Yes] when asked if you want to reboot the system.
RESTORING THE FACTORY IMAGE
The Restore Disc that came with your system contains two utilities:
The Recovery utility allows you to restore the original contents of the C: drive.
The Hard Disk Data Delete utility on this disc is used to delete all data on your hard disk and prevent it from being reused. Do not use the Hard Disk Data Delete utility unless you are absolutely certain that you want to erase your entire hard disk, including all partitions.
• The use of this disc requires that you have a device capable of reading DVDs attached to your system. If you do not have a built-in DVD player, you will need to attach an external player. For more information on available external devices, visit our Web site at: us.fujitsu.com/ computers.
• This disc can only be used with the system with which it was purchased.
BOOT Priority Change
Before restoring an image, you must first verify that your system is set up to boot from the DVD drive. To verify/ change the boot-up priority (rather than booting-up from the hard drive or an external floppy disk drive), perform the following steps:
1. Start your system and press the [F2] key when the Fujitsu logo appears. You will enter the BIOS Setup Utility.
2. Using the arrow keys, go to the Boot menu.
3. Arrow down to the Boot Device Priority submenu. Press [Enter].
4. If “Optical Media Drive” or “CD-ROM Drive” is not at the top of the list, arrow down to the drive in the list, and press the space bar (or the + key) to move it to the top of the list. (The system attempts to boot from the devices in the order in which they are listed.). Note that the BIOS for some systems will indicate “CD-ROM Drive”, even when a DVD drive is connected.
5. If you have an external DVD drive connected, proceed to step 6; otherwise, proceed to step 7.
6. If you have an external DVD drive connected:
• Select the Advanced menu in the BIOS window.
• Scroll down to the USB Features submenu and press the Enter key to open it.
75
P7120.book Page 76 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Six
• If Legacy USB Support is disabled, press the space bar to enable it.
• Scroll down to SCSI SubClass Support and press the space bar to enable it.
7. Press [F10], then click on [Yes] to exit the BIOS Setup Utility and return to the boot process.
After you have changed the boot priority, you can restore a backup image when you are booting up.
Procedure
1. Turn on the power to your system.
2. Ensure that you have a device that can read DVDs
either installed in your system or attached exter­nally to it.
3. Insert the Restore Disc into the drive tray.
4. Reboot your system.
5. After the system reboots, follow the instructions
that appear to either restore your system image or erase all data from your hard disk.
AUTOMATICALLY DOWNLOADING DRIVER UPDATES
Your system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system.
The FDU icon should appear in the system tray at the bottom right of your screen (roll the cursor over the icons to find the correct one). If the FDU icon does not appear in the system tray, it can be started by going to [Start] -> All Programs, and clicking on Fujitsu Driver Update; this will create the icon automatically.
To invoke the FDU menu, right-click on the FDU icon. The menu contains the following items:
Check for updates now
Allows for manual driver update search. The first time it is used, you are prompted to agree to a user agreement. After clicking on the icon, the FDU auto­matically connects with the Fujitsu site to check for updates and downloads them. While downloading, the icon has a red bar through it, indicating that it cannot be used while the download is in process. When the update is complete, a message appears informing you of the fact.
Enable Automatic Update Notifications
Automatically searches for new updates on a regular basis (approximately every 3 days).
Show update history
Brings up a screen that displays a history of updates that have been made via the FDU.
About Fujitsu Driver Update
Displays the FDU version number and copyright information
Fujitsu Driver Update Readme
Displays the FDU readme.
76
P7120.book Page 77 Monday, October 10, 2005 4:38 PM
Care and Maintenance
7
77
P7120.book Page 78 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Seven
78
P7120.book Page 79 Monday, October 10, 2005 4:38 PM
Care and Maintenance
If you use your Fujitsu LifeBook notebook carefully, you will increase its life and reliability. This section provides
some tips for looking after the notebook and its devices.
Electrical equipment may be hazardous if misused. Operations of this product or simi­lar products, must always be supervised by an adult. Do not allow children access to the interior of any electrical products and do not permit them to handle any cables.
Care and Maintenance
Do not drop your notebook.
Do not touch the screen with any sharp objects.
Cleaning your LifeBook notebook
Always disconnect the power plug. (Pull the plug, not the cord.)
Clean your LifeBook notebook with a damp, lint-free cloth. Do not use abrasives or solvents.
Use a soft cloth to remove dust from the screen. Never use glass cleaners.
Caring for your LifeBook notebook
Your LifeBook notebook is a durable but sensitive elec­tronic device. Treat it with respect and care.
Make a habit of transporting it in a suitable carrying case.
Do not attempt to service the computer yourself. Always follow installation instructions closely.
To protect your notebook from damage and to opti­mize system performance, be sure to keep all air all vents unobstructed, clean, and clear of debris. This may require periodic cleaning, depending upon the environment in which the system is used.
Keep the computer away from food and beverages.
If you accidentally spill liquid on your LifeBook note­book:
1. Turn it off.
2. Position it so that the liquid can run out.
3. Let it dry out for 24 hours, or longer if needed.
4. If your notebook will not boot after it has dried out, call your support representative.
Do not use your Fujitsu LifeBook notebook in a wet environment (near a bathtub, swimming pool).
Always use the AC adapter and batteries that are approved for your notebook.
Avoid exposure to sand, dust and other environmental hazards.
Do not expose your notebook to direct sunlight for long periods of time as temperatures above 140° F (60° C) may damage your notebook.
Keep the covers closed on the connectors and slots when they are not in use.
Do not put heavy or sharp objects on the computer.
If you are carrying your LifeBook notebook in a brief­case, or any other carrying case, make sure that there are no objects in the case pressing on the lid.
Never position your notebook such that the DVD/CD­RW drive is supporting the weight of the notebook.
Storing your LifeBook notebook
If storing your notebook for a month or longer, turn your LifeBook notebook off, charge the battery, then remove and store all Lithium ion batteries.
Store your notebook and batteries separately. If you store your LifeBook with a battery installed, the battery will discharge, and battery life will be reduced. In addi­tion, a faulty battery might damage your LifeBook.
Store your Fujitsu LifeBook in a cool, dry location. Temperatures should remain between 13ºF (-10ºC) and 140ºF (60ºC).
Traveling with your LifeBook notebook
Do not transport your notebook while it is turned on.
Do not check your notebook as baggage. Carry it with you.
Always bring your backup disk and Drivers and Applications CD that came with your notebook when you travel. If you experience system software problems while traveling, you may need it to correct any prob­lems.
Never put your notebook through a metal detector. Have your notebook hand-inspected by security per­sonnel. You can however, put your notebook through a properly tuned X-ray machine. To avoid problems, place your notebook close to the entrance of the machine and remove it as soon as possible or have your notebook hand-inspected by security personnel. Secu­rity officials may require you to turn your notebook On. Make sure you have a charged battery on hand.
When traveling with the hard drive removed, wrap the drive in a non-conducting materials (cloth or paper). If you have the drive checked by hand, be ready to install the drive if needed. Never put your hard drive through a metal detector. Have your hard drive hand-inspected by security personnel. You can however, put your hard drive through a properly tuned X-ray machine.
Take the necessary plug adapters if you're traveling over­seas. Check the following diagram to determine which plug adapter you'll need or ask your travel agent.
79
P7120.book Page 80 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Seven
Outlet Type Location
United States, Canada, parts of Latin America,
Mexico, Japan, Korea,
the Philippines, Taiwan
Russia and the Commonwealth
of Independent States (CIS),
most of Europe, parts of Latin
America, the Middle East, parts
of Africa, Hong Kong, India,
most of South Asia
United Kingdom, Ireland,
Malaysia, Singapore,
parts of Africa
China, Australia,
New Zealand
BATTERIES
Caring for your Batteries
Always handle batteries carefully.
Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire.
Do not drop, puncture, disassemble, mutilate or incin­erate the battery.
Recharge batteries only as described in this manual and only in ventilated areas.
Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten battery life.
Do not leave a battery in storage for longer than 6 months without recharging it.
Increasing Battery Life
Power your LifeBook notebook through the AC or optional auto/airline adapter whenever possible.
If your notebook is running on battery power all day, connect it to the AC adapter overnight to recharge the battery.
Keep brightness to the lowest level comfortable.
Set the power management for maximum battery life.
Put your notebook in Suspend mode when it is turned on and you are not actually using it.
Limit your media drive access.
Disable the DVD/CD-RW Combo Drive auto insert noti­fication function.
Always use fully charged batteries.
Eject PCMCIATM cards when not in use.
FLOPPY DISKS AND DRIVES
Caring for your Floppy Disks
Avoid using the floppy disks in damp and dusty locations.
Never store a floppy disk near a magnet or magnetic field.
Do not use a pencil or an eraser on a disk or disk label.
Avoid storing the floppy disks in extremely hot or cold locations, or in locations subject to severe temperature changes. Store at temperatures between 50º F (10ºC) and 125ºF (52ºC).
Do not touch the exposed part of the disk behind the metal shutter.
Caring for your Floppy Disk Drive
To clean, wipe the floppy disk drive clean with a dry soft cloth, or with a soft cloth dampened with water or a solution of neutral detergent. Never use benzene, paint thinner or other volatile material.
Avoid storing the floppy disk drive in extremely hot or cold locations, or in locations subject to severe tempera­ture changes. Store at temperatures between 50º F (10º C) and 125ºF (52º C).
Keep the floppy disk drive out of direct sunlight and away from heating equipment.
Avoid storing the floppy disk drive in locations subject to shock and vibration.
Never use the floppy disk drive with any liquid, metal, or other foreign matter inside the floppy disk drive or disk.
Never disassemble or dismantle your floppy disk drive.
80
P7120.book Page 81 Monday, October 10, 2005 4:38 PM
Care and Maintenance
MEDIA CARE
Caring for your Media Discs
Media discs are precision devices and will function reli­ably if given reasonable care.
Always store your media disc in its case when it is not in use.
Always handle discs by the edges and avoid touching the surface.
Avoid storing any media discs in extreme temperatures.
Do not bend media discs or set heavy objects on them.
Do not spill liquids on media discs.
Do not scratch media discs.
Do not get dust on media discs.
Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen.
If a media disc is subjected to a sudden change in tem­perature, cold to warm condensation may form on the surface. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at room temperature. DO NOT use a hair dryer or heater to dry media discs.
If a disc is dirty, use only a DVD/CD cleaner or wipe it with a clean, soft, lint free cloth starting from the inner edge and wiping to the outer edge.
PC CARDS
Caring for your PC Cards
PC Cards are durable, but you must treat them with care. The documentation supplied with your PC Card will provide specific information, but you should pay attention to the following points:
To keep out dust and dirt, store PC Cards in their protective sleeves when they are not installed in your LifeBook notebook.
Avoid prolonged exposure to direct sunlight or excessive heat.
Keep the cards dry.
Do not flex or bend the cards, and do not place heavy objects on top of them.
Do not force cards into the slot.
Avoid dropping cards, or subjecting them to excessive vibration.
Caring for your Optical Drive
Your optical drive is durable but you must treat it with care. Please pay attention to the following points:
The drive rotates the compact disc at a very high speed. Do not carry it around or subject it to shock or vibration with the power on.
Avoid using or storing the drive where it will be exposed to extreme temperatures.
Avoid using or storing the drive where it is damp or dusty.
Avoid using or storing the drive near magnets or devices that generate strong magnetic fields.
Avoid using or storing the drive where it will be sub­jected to shock or vibration.
Do not disassemble or dismantle the DVD/CD-RW drive.
Occasional use of a commercially available lens cleaner kit is recommended to maintain your drive.
81
P7120.book Page 82 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Seven
82
P7120.book Page 83 Monday, October 10, 2005 4:38 PM
Specifications
8
83
P7120.book Page 84 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Eight
84
P7120.book Page 85 Monday, October 10, 2005 4:38 PM
Specifications
Specifications
This section provides the hardware and environmental specifications for your Fujitsu LifeBook notebook. Specifications of particular configurations will vary.
Part Number
Configuration P/N: AV0XXXXXXXXXXXXX
FPC P/N: FPCMXXXXXX
P7120, PM ULV 753, 10.6 WXGA, 256M, 60G, MODEM/LAN/WLAN, WIN XPH
Model #
MICROPROCESSOR
Intel® Pentium® M Processor ULV 753 (1.2 GHz, 2 MB L2 Cache, 400 MHz Front Side Bus)
MEMORY
System Memory
256 MB minimum, 2GB maximum, micro-DIMM DDR2-400 SDRAM
Two micro-DIMM slots (one accessible)
256 MB, 512 MB, and 1GB memory modules available
BIOS Memory
1 MB Firmware Hub (FWH) Flash ROM
VIDEO
Built-in color 10.6” Wide XGA Crystal View TFT active matrix LCD display with simultaneous display capa­bility.
Intel® 915GMS video graphics chip with integrated 32­bit 3D/2D gfx core and Accelerated Graphics Port (AGP) support.
Up to 128 MB shared video memory using Dynamic Video Memory Technology 2.0.
Video Color and Resolution
10.6" TFT Wide XGA
Internal: 1280 x 768 pixel resolution, 16M colors
External: 1600 x 1200 pixel resolution, 16M colors Simultaneous Video: 1024 x 768, 16M colors, XGA, SVGA and VGA compatible
AUDIO
Realtek ALC260 codec with 18-bit stereo audio
Stereo headphone/line-out port
Mono microphone jack, 100 mV
Dolby Headphone signal processing utility (in the InterVideo DVD software)
Processor
rms
Screen Size
Memory
Figure 8-1 Configuration Label
max.
CONFIGURATION LABEL
The configuration label located on the bottom of your LifeBook notebook (See figure 2-7 on page 11 for location) contains information regarding the options you’ve chosen for your notebook. Following is an example label and information on how to read your own configuration label.
Configuration ID
Hard Drive
Two built-in stereo speakers, 25 mm x 14 mm, bass
Communications
Operating System
reflex
Built-in microphones one either side of the display.
MASS STORAGE DEVICE OPTIONS
Hard Drive
20 GB, 30 GB, or 60 GB, fixed hard drive, 1.8”, Ultra DMA 100
Modular DVD/CD-RW Combo Drive
8x DVD / 10x CD-RW / 24x CD-R / 24x CD-ROM
Modular Dual-Layer Multi-Format DVD Writer
2.4x DVD+R DL, 4x DVD-R, 2x DVD-RW, 4x DVD+R,
2.4x DVD+RW, 2x DVD-RAM, 8x DVD-ROM, 24x CD­R, 10x CD-RW, 24x CD-ROM
FEATURES
Communications
Modem: Internal V.90 standard 56K fax/modem (ITU V.90, 56K data, 14.4K fax)
LAN: 10/100 Base-TX Ethernet
Integrated Intel PRO/Wireless 2915ABG Network Connections (Tri-mode 802.11a/b/g*) with Antenna On/Off switch (available in LifeBook P7120 model),
or,
Integrated Atheros Super AG Wireless LAN (802.11a/ b/g*) with Antenna On/Off switch (available in Life­Book P7120D model)
Optional Bluetooth device for wireless personal area network communication
* Operates at 2.4 GHz and 5.0 GHz; communications range may
vary, depending upon environment.
Integrated Pointing Device
Touchpad pointing device with combination fingerprint sensor*/scroll button.
* Fingerprint Sensor: AuthenTec fingerprint slide sensor
(AES2501)
85
P7120.book Page 86 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Eight
Theft Prevention Lock Slot
Slot for use with physical restraining security systems.
DEVICE PORTS
PC Card slot for one Type II card: PCMCIA Standard
2.1 with CardBus support
One connector for external monitor (see Display specifications)
One Memory Stick/SD/xD slot
Three USB 2.0 connectors for input/output devices
One S-Video Out port
One modular modem (RJ-11) connector
One LAN (RJ-45) port
One IEEE 1394 port
One stereo headphone/line-out jack. (See Audio speci­fications)
One mono microphone jack. (See Audio specifications)
KEYBOARD
Built-in keyboard with all functions of 101 key keyboards.
Total number of keys: 82
Function keys: [F1] through [F12]
Feature extension key: [Fn]
Two Windows keys: one Start and one application key
Key pitch: 17.5 mm
Key stroke: 2 mm
Built-in Touchpad pointing device with left and right buttons and scroll button.
Built-in palm rest
External Keyboard Support
USB-compatible
External Mouse Support
USB-compatible
DIMENSIONS AND WEIGHT
Overall Dimensions
Approximately 10.28"(w) x 7.83"(d) x 1.26/1.43"(h) (261mm x 199 mm x 32/36 mm)
Weights
Approximately 3.0 lbs (1.50 kg) with standard battery and DVD/CD-RW combo drive
ENVIRONMENTAL REQUIREMENTS
Te mp e r at u r e
Operating: 41° to 95° F (5° to 35° C) Non-operating: 5° to 140° F (–15° to 60° C)
Humidity
Operating: 20% to 85%, relative, non-condensing Non-operating; 8% to 85%, relative, non-condensing
Altitude
Operating: 10,000 feet (3,048 m) maximum
POPULAR ACCESSORIES
For ordering or additional information on Fujitsu accessories please visit our Web site at: www.shopfujitsu.com or call 1-800-FUJITSU.
POWER
Batteries
One standard 4-cell high-capacity Lithium ion battery, rechargeable, 7.2V, 5200 mAh
Optional high-capacity 6-cell Lithium ion battery, rechargeable, 7.2V, 7800 mAh
Optional second bay battery: 4-cell Lithium ion battery, rechargeable, 10.8V, 2300 mAh
AC Adapter
Autosensing 100-240V AC, 60W, supplying 16V DC,
3.75A to the LifeBook notebook, which includes an AC cable.
Power Man agement
Conforms to ACPI (Advanced Configuration and Power Interface)
86
P7120.book Page 87 Monday, October 10, 2005 4:38 PM
Specifications
PRE-INSTALLED SOFTWARE
Depending on your pre-installed operating system, your Fujitsu LifeBook notebook comes with pre-installed software for playing audio and video files of various formats. In addition there is file transfer software, virus protection software and Power Management software.
LEARNING ABOUT YOUR APPLICATION SOFTWARE
Tutorials
All operating systems and most application software have tutorials built into them upon installation. We highly recommend that you step through the tutorial before you use an application.
Manuals
Included with your notebook you will find manuals for your installed operating system and other pre-installed software. Any manuals that are not included, are avail­able online through the help system of the software. We recommend that you review these manuals for general information on the use of these applications.
Reader
Adobe
The Adobe Reader allows you to view, navigate, and print PDF files from across all of the major computing platforms.
Norton AntiVirus 2005
Your system is preinstalled with a free 90-day trial version of Symantec’s Norton AntiVirus™ 2005. Norton AntiVirus is a program designed to protect your Life­Book notebook from computer viruses. It assists in the protection of the data currently residing on your hard disk from destruction or contamination. The 90-day trial version is activated upon your acceptance of soft­ware license agreement. After 90 days, it will be neces­sary to purchase a subscription from Symantec to download latest virus definitions.
(See your online help or manual for more information on how and when to run this program).
MS Works
Microsoft Works is a suite of software containing the basic tools to write letters and reports, track family and friends with address books, manage home finances, and create a home inventory.
Depending upon your system configuration, one of the following applications will be installed on your note­book:
Microsoft Works 8.0
Microsoft Works 8.0 is a suite of software containing the basic tools to write letters and reports, track family and friends with address books, manage home finances, and create a home inventory.
Microsoft Office SBE
(On Microsoft Windows XP Professional models only)
Microsoft Small Business Edition (SBE) is a suite of applications designed to help run a small business while increasing productivity. Among the programs included in Microsoft SBE are Microsoft Word, Excel, and Power­Point.
Fujitsu HotKey Utility
Utility for adjusting the brightness level on your LifeBook notebook.
Fujitsu Driver Update
The Fujitsu Driver Update (FDU) utility allows you to choose to automatically or manually go to the Fujitsu site to check for new updates for your system.
Quicken 2005 New User Edition
Quicken 2005 New User Edition by Intuit is a personal money management program. It has features such as portfolio management, account registries, on-line banking and bill paying. This application is for new users who are using Quicken software for the first time. Full version upgrade information is available on line.
87
P7120.book Page 88 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Eight
88
P7120.book Page 89 Monday, October 10, 2005 4:38 PM
Regulatory Information
Regulatory Information
NOTICE
Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment.
FCC NOTICES Notice to Users of Radios and Television
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protec­tion against harmful interference in a residential installa­tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a partic­ular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
n
Reorient or relocate the receiving antenna.
n
Increase the separation between the equipment and receiver.
n
Connect the equipment into an outlet that is on a different circuit than the receiver.
n
Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device.
Notice to Users of the US Telephone Network
This equipment complies with Part 68 of the FCC rules, and the requirements adopted by ACTA. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment; or a product identifier in the format US:AAAEQ##TXXXX. If requested, this infor­mation or number must be provided to the telephone company.
This equipment is designed to be connected to the tele­phone network or premises wiring using a standard jack type USOC RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant.
The ringer equivalent number (REN) of this equipment is 0.1B as shown on the label. The REN is used to deter­mine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local tele­phone company.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facili­ties, equipment, operations or procedures that could effect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to main­tain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information, please refer to the manual or contact Fujitsu Computer Systems Corporation, Customer Service. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
The equipment cannot be used on public coin service provided by the telephone company. Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commis­sion or corporation commission for information).
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this computer does not disable your alarm equip­ment. If you have any questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date an time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such busi­ness, other entity, or individual.
89
P7120.book Page 90 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook - Section Eight
DOC (INDUSTRY CANADA) NOTICES Notice to Users of Radios and Television
This Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations.
CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada.
Notice to Users of the Canadian Telephone Network
NOTICE: This equipment
meets the applicable Industry Canada Terminal
Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indi­cating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
Before connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certification standards does not prevent service degradation in some situations.
Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu or any equipment failures may give the telecom­munication company cause to request the user to disconnect the equipment from the telephone line.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1B. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equiva-
lence Numbers of all the devices does not exceed five.
For safety, users should ensure that the electrical ground of the power utility, the telephone lines and the metallic water pipes are connected together. Users should NOT attempt to make such connections themselves but should contact the appro­priate electric inspection authority or elec­trician. This may be particularly important in rural areas.
Avis Aux Utilisateurs Du Réseau Téléphonique Canadien
AVIS: Le présent matériel est conforme aux spécifications techniques d’Industrie Canada applicables au matériel terminal. Cette confor­mité est confirmée par le numéro d’enregistrement. Le sigle IC, placé devant le numéro d’enregistrement, signifie que l’enregistrement s’est effectué conformé­ment à une déclaration de conformité et indique que les spécifications techniques d’Industrie Canada ont été respectées. Il n’implique pas qu’Industrie Canada a approuvé le matériel.
Avant de connecter cet équipement à une ligne télépho­nique, l’utilisateur doit vérifier s’il est permis de connecter cet équipement aux installations de télécom­munications locales. L’utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service.
Les réparations de l’équipement de télécommunications doivent être effectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur décon­necte l’équipement de la ligne téléphonique.
AVIS: L’indice d’équivalence de la sonnerie (IES) du présent matériel est de 0.1B. L’IES assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équiva-
lence de la sonnerie de tous les dispositifs n’excède pas 5.
Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise de terre du ser­vice d’électricité, les lignes télphoniques et les conduites d’eau métalliques sont con­nectées ensemble. Les utilisateurs NE doivent PAS tenter d’établir ces connex­ions eux-mêmes, mais doivent contacter les services d’inspection d’installations électriques appropriés ou un électricien. Ceci peut être particulièrement important en régions rurales.
90
P7120.book Page 91 Monday, October 10, 2005 4:38 PM
Glossary
9
91
P7120.book Page 92 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Nine
92
P7120.book Page 93 Monday, October 10, 2005 4:38 PM
Glossary
Glossary
AC Adapter
A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your LifeBook notebook.
ACPI
Advanced Configuration and Power Interface. An industry specification for the efficient handling of power consumption in mobile computers. ACPI determines how a computer's BIOS, operating system, and periph­erals communicate with each other about power management.
Active-Matrix Display
A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.
ADSL
Asymmetric Digital Subscriber Line. Technology for transporting high bit-rate services over ordinary phone lines.
APM
Advanced Power Management.
Auto/Airline Adapter
A device which converts the DC voltage from an auto­mobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LifeBook note­book.
Byte
8 bits of parallel binary information.
Cache Memory
A block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster.
CardBus
A faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI architecture.
CD-ROM
Compact disc read only memory. This is a form of digital data storage which is read optically with a laser rather than a magnetic head. A typical CD-ROM can contain about 600MB of data and is not subject to heads crashing into the surface and destroying the data when there is a failure nor to wear from reading.
CMS
Code Morphing Software. Crusoe processor software architecture that results in longer battery life. For more information on CMS, click on the Technology link on the refer to the Transmeta web site at: www.trans­meta.com.
Command
An instruction which you give your operating system. Example: run a particular application or format a floppy disk.
BIOS
Basic Input-Output System. A program and set of default parameters stored in ROM which tests and operates your LifeBook notebook when you turn it on until it loads your installed operating system from disk. Information from the BIOS is transferred to the installed operating system to provide it with information on the configuration and status of the hardware.
Bit
An abbreviation for binary digit. A single piece of information which is either a one (1) or a zero (0).
bps
An abbreviation for bits per second. Used to describe data transfer rates.
Boot
To start-up a computer and load its operating system from disk, ROM or other storage media into RAM.
Bus
An electrical circuit which passes data between the CPU and the sub-assemblies inside your LifeBook notebook.
Configuration
The combination of hardware and software that makes up your system and how it is allocated for use.
Data
The information a system stores and processes.
DC
Direct current. A voltage or current that does not fluctuate periodically with time.
Default Value
A pre programmed value to be used if you fail to set your own.
DIMM
Dual-in-line memory module.
Disk
A spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly called a diskette.
93
P7120.book Page 94 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Nine
Disk Drive
The hardware which spins the disk and has the heads and control circuitry for reading and writing the data on the disk.
Diskette
A floppy disk in a hard housing with a shutter.
DMA
Direct Memory Access. Special circuitry for memory to memory transfers of data which do not require CPU action.
DMI
Desktop Management Interface. A standard that provides PC management applications with a common method of locally or remotely querying and configuring PC computer systems, hardware and software compo­nents, and peripherals.
DOS
Disk Operating System (MS-DOS is a Microsoft Disk Operating System).
Driver
A computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment.
ESD
Electro-Static Discharge. The sudden discharge of elec­tricity from a static charge which has built-up slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get from brushing hair on a dry day.
Extended Memory
All memory more than the 640KB recognized by MS-DOS as system memory.
FCC
Federal Communication Commission.
Floppy Disk
A spinning platter of magnetic data storage media which is highly flexible.
I/O
Input/Output. Data entering and leaving your LifeBook notebook in electronic form.
I/O Port
The connector and associated control circuits for data entering and leaving your LifeBook notebook in elec­tronic form.
IDE
Intelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit.
IEEE 1394
The IEEE 1394 (also known as “Firewire” or “iLink”) standard allows you to connect devices that are compliant with IEEE standard 1394. This port is effec­tively a very fast communications port. This architecture is very good for transferring large files, such as those from digital cameras.
IRQ
Interrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed.
KB
Kilobyte.
LAN
Local Area Network. An interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.
LCD
Liquid Crystal Display. A type of display which makes images by controlling the orientation of crystals in a crystalline liquid.
Lithium ion Battery
A type of rechargeable battery which has a high power­time life for its size and is not subject to the memory effect as Nickel Cadmium batteries.
MB
Megabyte.
GB
Gigabyte.
Hard drive
A spinning platter of magnetic data storage media where the platter is very stiff.
Hexadecimal
A decimal notation for the value of a 4 bit binary number. (0-9, A, B, C, D, E, F) Example: 2F in hexadecimal = 00101111 in binary = 47 in decimal.
94
Megahertz
1,000,000 cycles per second.
Memory
A repository for data and applications which is readily accessible to your LifeBook notebook CPU.
MHz
Megahertz.
P7120.book Page 95 Monday, October 10, 2005 4:38 PM
Glossary
Modem
A contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line.
Monaural
A system using one channel to process sound from all sources.
NTSC
National TV Standards Commission. The standard for TV broadcast and reception for the USA.
Operating System
A group of control programs that convert application commands, including driver programs, into the exact form required by a specific brand and model of micro­processor in order to produce the desired results from that particular equipment.
Partition
A block of space on a hard drive which is set aside and made to appear to the operating system as if it were a separate disk, and addressed by the operating system accordingly.
PCMCIA
PCMCIA is a trademark of the Personal Computer Memory Card International Association. The Personal Computer Memory Card International Association is an organization that sets standards for add-in cards for personal computers.
Peripheral Device
A piece of equipment which performs a specific function associated with but not integral to a computer. Examples: a printer, a modem, a CD-ROM.
Pitch (keyboard)
The distance between the centers of the letter keys of a keyboard.
Pixel
The smallest element of a display, a dot of color on your display screen. The more pixels per area the clearer your image will appear.
POP3
Post Office Protocol. Protocol that is used to retrieve email from a mail server.
POST
Power On Self Test. A program which is part of the BIOS which checks the configuration and operating condition of your hardware whenever power is applied to your LifeBook notebook. Status and error messages may be displayed before the operating system is loaded. If the self test detects failures that are so serious that operation can not continue, the operating system will not be loaded.
PPPoE
Point to Point Protocol over Ethernet. A protocol for Ethernet, using a Point-to-Point Protocol (PPP), which is used for connection on the phone line.
Program
An integrated set of coded commands to your computers telling your hardware what to do and how and when to do it.
PS/2
A series of personal computers which established a number of standards for connecting external devices such as keyboards and monitors.
RAM
Random Access Memory. A hardware component of your LifeBook notebook that holds binary information (both program and data) as long as it has the proper power applied to it.
RAM Module
A printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools.
Reset
The act of reloading the operating system. A reset erases all information stored in RAM.
Restart
See Reset.
Resume
To proceed after interruption. In your LifeBook note­book, this refers to returning to active operation after having been in one of the suspension states.
ROM
Read Only Memory. A form of memory in which infor­mation is stored by physically altering the material. Data stored in this way can not be changed by your LifeBook notebook and does not require power to maintain it.
SDRAM
Synchronous Dynamic Random Access Memory.
Shadow RAM
A technique of copying data or applications stored in ROM (Read Only Memory) into RAM (Random Access Memory) for access during actual operation. RAM is much faster to access than ROM, however ROM contents are not lost when power is removed. Shadowing allows permanently stored information to be rapidly accessed.
SPDIF
Sony Philips Digital Interface. Technology that allows you to download digital audio data onto a MiniDisc recorder.
95
P7120.book Page 96 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Section Nine
SSID
Service Set Identifier. Specifies which network you are joining. Some systems allow you to specify any SSID as an option so you can join any network.
Status Indicator
A display which reports the condition of some portion of your hardware. On your LifeBook notebook this is an LCD screen just above the keyboard.
Stereo (audio)
A system using two channels to process sound from two different sources.
Stroke (keyboard)
The amount of travel of a key when it is pressed from resting to fully depressed.
Suspend
To make inoperative for a period of time. Your LifeBook notebook uses various suspension states to reduce power consumption and prolong the charge of your battery.
SVGA
Super VGA. Standard that provides 800x600 pixel resolution and a palette of 16M colors.
S-Video
Super Video. A component video system for driving a TV or computer monitor.
System Clock
An oscillator of fixed precise frequency which synchro­nizes the operation of the system and is counted to provide time of day and date.
TFT
Thin Film Transistor. A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually.
UL
Underwriters Laboratories – An independent organiza­tion that tests and certifies the electrical safety of devices.
USB
Universal Serial Bus. An external bus standard that allows for fast data transfer. A single USB port can be used to connect up to 127 peripheral devices, such as
mice, modems, and scanners. USB 1.1 has a transfer speed of a maximum of 12Mb/s. USB 2.0 is much faster, transferring at up to 480Mb/s. USB 2.0 is backward­compatible to work with USB 1.1 devices.
VGA
Video Graphics Array. A video display standard which provides resolutions of 720 x 400.
VRAM
Video Random Access Memory. A memory dedicated to video display data and control.
WEP
Wired Equivalent Privacy. WEP is a protocol for increasing privacy over wireless LANs. The protocol works by encrypting data while being transmitted over radio waves.
WFM
Wired for Management is Intel’s broad-based initiative to reduce the total cost of ownership (TCO) of business computing without sacrificing power and flexibility.
Wi-Fi Compatible
Wi-Fi ( Wireless Fidelity) identifies that the product has passed the interoperability test, supplied by the WECA (Wireless Ethernet Compatibility Alliance), which guar­antees the interoperability of wireless IEEE 802.11 LAN products. For more information on the Wi-Fi standard, go to the WECA website at: www.wirelessethernet.com.
Write Protect
Prevent alteration of the binary state of all bits in a storage media. Example: all information on a device such as a floppy diskette; a block of space in a storage media such as a partition of a hard drive; a file or direc­tory of floppy diskette or hard drive.
XGA
Extended graphics array. Standard that provides resolutions of 640x480 or 1024x764, supporting 64k colors.
96
P7120.book Page 97 Monday, October 10, 2005 4:38 PM
Appendix A
Using the Fingerprint Sensor
97
P7120.book Page 98 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Appendix
98
P7120.book Page 99 Monday, October 10, 2005 4:38 PM
Using the Fingerprint Sensor
Fingerprint Sensor Device
INTRODUCING THE FINGERPRINT SENSOR DEVICE
Your system has an optional fingerprint sensor device below the Touchpad, between the left and right buttons. This also serves as a scroll button. (Figure 1)
Figure A-1 Fingerprint sensor
Although the system may have a fingerprint sensor in place of a scroll button, the fingerprint sensor can be used for scrolling. Simply move your fingerprint over the sensor the same as you would use a scroll button.
With a fingerprint sensor, you can avoid having to enter a username and password every time you want to:
Log onto Windows
Recover from suspend mode
Cancel a password-protected screen saver
Log into homepages that require a username and pass­word
After you have “enrolled” - or registered - your finger­print, you can simply swipe your fingertip over the sensor for the system recognize you.
The fingerprint sensor uses Softex OmniPass which provides password management capabilities to Microsoft Windows operating systems. OmniPass enables you to use a "master password" for all Windows, applications, and on-line passwords.
OmniPass requires users to authenticate themselves using the fingerprint sensor before granting access to the Windows desktop. This device results in a secure authentication system for restricting access to your computer, applications, web sites, and other password­protected resources.
OmniPass presents a convenient graphical user interface, through which you can securely manage passwords, users, and multiple identities for each user.
GETTING STARTED
This section guides you through the preparation of your system for the OmniPass fingerprint recognition application. You will be led through the OmniPass installation process. You will also be led through the procedure of enrolling your first user into OmniPass.
INSTALLING OMNIPASS
If OmniPass has already been installed on your system, skip this section and go directly to “User Enrollment” on page 100. You can determine whether OmniPass has already been installed by checking to see if the following are present:
The presence of the gold key-shaped OmniPass icon in the system tray at the bottom right of the screen.
The presence of the Softex program group in the Programs group of the Start menu
System Requirements
The OmniPass application requires space on your hard drive; it also requires specific Operating Systems (OS’s). The minimum requirements are as follows:
Windows XP Home Edition or Windows XP Profes­sional operating system
At least 35 MB available hard disk space
Installing the OmniPass Application
If OmniPass is already installed on your system, go to “User Enrollment” on page 100. Otherwise continue with this section on software installation.
For installation, OmniPass requires that the user installing OmniPass have administrative privileges to the system. If your current user does not have administrative privileges, log out and then log in with an administrator user before proceeding with OmniPass installation.
To install OmniPass on your system you must:
1. Insert the installation media for the OmniPass appli­cation into the appropriate drive. If you are installing from CD-ROM or DVD-ROM, you must find and launch the OmniPass installation program (setup.exe) from the media.
2. Follow the directions provided in the OmniPass installation program. Specify a location to which you would like OmniPass installed mended that you NOT install OmniPass in the root directory (e.g. C:\).
3. Once OmniPass has completed installation you will be prompted to restart you system. Once your system has rebooted you will be able to use OmniPass. If you choose not to restart immediately after installation, OmniPass will not be available for use until the next reboot.
. It is recom-
99
P7120.book Page 100 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Appendix
The installation program automatically places an icon (Softex OmniPass) in the Windows Control Panel as well as a golden key shaped icon in the taskbar.
Verifying Information about OmniPass
After you have completed installing OmniPass and restarted your system, you may wish to check the version of OmniPass on your system.
To check the version information of OmniPass:
1. From the Windows Desktop, double-click the key­shaped OmniPass icon in the taskbar (usually located in the lower right corner of the screen), or, Click the Start button, select Settings, and click Control Panel (if you are using Windows XP you will see the Control Panel directly in the Start menu; click it, then click Switch to Classic View). Double­click Softex OmniPass in the Control Panel, and the OmniPass Control Center will appear. If it does not appear, then the program is not properly installed, or, Click the Start button, select Programs, and from the submenu select the Softex program group, from that submenu click OmniPass Control Center.
2. Select the About tab at the top of the OmniPass Control Panel. The About tab window appears with version information about OmniPass.
Uninstalling OmniPass
For uninstallation, OmniPass requires that the user uninstalling OmniPass have administrative privileges to the system. If your current user does not have administrative privileges, log out and then log in with an administrator user before proceeding with OmniPass uninstallation.
To remove the OmniPass application from your system:
1. Click Start on the Windows taskbar. Select Settings, and then Control Panel.
2. Double-click Add/Remove Programs.
3. Select OmniPass, and then click Change/Remove.
4. Follow the directions to uninstall the OmniPass application.
5. Once OmniPass has finished uninstalling, reboot your system when prompted.
USER ENROLLMENT
Before you can use any OmniPass features you must first enroll a user into OmniPass.
Master Password Concept
Computer resources are often protected with passwords. Whether you are logging into your computer, accessing your email, e-banking, paying bills online, or accessing
100
network resources, you often have to supply credentials to gain access. This can result in dozens of sets of creden­tials that you have to remember.
During OmniPass user enrollment a "master password” is created for the enrolled user. This master password “replaces” all other passwords for sites you register with OmniPass.
Example: A user, John, installs OmniPass on his system (his home computer) and enrolls an OmniPass user with username “John_01” and password “freq14”. He then goes to his webmail site to log onto his account. He inputs his webmail credentials as usual (username “John_02” and password “lifebook”), but instead of clicking [Submit], he directs OmniPass to Remember Password. Now whenever he returns to that site, OmniPass will prompt him to supply access credentials.
John enters his OmniPass user credentials (“John_01” and “freq14”) in the OmniPass authentication prompt, and he is allowed into his webmail account. He can do this with as many web sites or password protected resources he likes, and he will gain access to all those sites with his OmniPass user credentials (“John_01” and “freq14”). This is assuming he is accessing those sites with the system onto which he enrolled his OmniPass user. OmniPass does not actually change the credentials of the password protected resource. If John were to go to an Internet cafe to access his webmail, he would need to enter his original webmail credentials (“John_02” and “lifebook”) to gain access. If he attempts his OmniPass user credentials on a system other than where he enrolled that OmniPass user, he will not gain access.
The enrollment procedure assumes you have no hardware authentication devices or alternate storage locations that you wish to integrate with OmniPass. If you desire such functionality, consult the appropriate sections of this document.
Basic Enrollment
The Enrollment Wizard will guide you through the process of enrolling a user. Unless you specified other­wise, after OmniPass installation the Enrollment Wizard will launch on Windows login. If you do not see the Enrollment Wizard, you can bring it up by clicking Start on the Windows taskbar; select Programs; select Softex; click OmniPass Enrollment Wizard.
1. Click Enroll to proceed to username and password verification. By default, the OmniPass Enrollment Wizard enters the credentials of the currently logged in Windows user.
2. Enter the password you use to log in to Windows. This will become the “master password” for this OmniPass user. In most cases, the Domain: value
P7120.book Page 101 Monday, October 10, 2005 4:38 PM
Using the Fingerprint Sensor
will be your Windows computer name. In a corpo­rate environment, or when accessing corporate resources, the Domain: may not be your Windows computer name. Click [Next] to continue.
3. In this step OmniPass captures your fingerprint. Refer to “Enrolling a Fingerprint” on page 101 for additional information.
4. Next, choose how OmniPass notifies you of various events. We recommend you keep Taskbar Tips on Beginner mode taskbar tips and Audio Tips on at least Prompt with system beeps only until you get accustomed to how OmniPass operates. Click [Next] to proceed with user enrollment. You will then see a Congratulations screen indicating your completion of user enrollment.
5. Click [Done] to exit the OmniPass Enrollment Wizard. You will be asked if you’d like to log in to OmniPass with your newly enrolled user; click [Yes].
Enrolling a Fingerprint
Enrolling a fingerprint will increase the security of your system and streamline the authentication procedure.
You enroll fingerprints in the OmniPass Control Center. With an OmniPass user logged in, double-click the system tray OmniPass icon. Select the User Settings tab and click Enrollment under the User Settings area. Click Enroll Authentication Device and authenticate at the authentication prompt to start device enrollment.
1. During initial user enrollment, you will be prompted to select the finger you wish to enroll. Fingers that have already been enrolled will be marked by a green check. The finger you select to enroll at this time will be marked by a red arrow. OmniPass will allow you re-enroll a finger. If you choose a finger that has already been enrolled and continue enrollment, OmniPass will enroll the fingerprint, overwriting the old fingerprint. Select a finger to enroll and click [Next].
2. It is now time for OmniPass to capture your selected fingerprint. It may take a several capture attempts before OmniPass acquires your fingerprint. Should OmniPass fail to acquire your fingerprint, or if the capture screen times out, click [Back] to restart the fingerprint enrollment process.
Your system has a “swipe” fingerprint sensor. A swipe sensor is small and resembles a skinny elon­gated rectangle. To capture a fingerprint, gently swipe or pull your fingertip over the sensor (starting at the second knuckle) towards yourself. Swiping too fast or too slow will result in a failed capture. The Choose Finger screen has a [Practice] button; click it to practice capturing your fingerprint. When you are comfortable with how your fingerprint is captured, proceed to enroll a finger.
3. Once OmniPass has successfully acquired the finger­print, the Ver if y F in ge rpr in t screen will automati­cally appear. To verify your enrolled fingerprint, place your fingertip on the sensor and hold it there as if you were having a fingerprint captured. Successful fingerprint verification will show a green fingerprint in the capture window and the text Ver i - fication Successful under the capture window.
USING OMNIPASS
You are now ready to begin using OmniPass. Used regu­larly, OmniPass will streamline your authentications.
Password Replacement
You will often use the password replacement function. When you go to a restricted access website (e.g., your bank, your web-based email, online auction or payment sites), you are always prompted to enter your login credentials. OmniPass can detect these prompts and you can teach OmniPass your login credentials. The next time you go to that website, you can authenticate with your fingerprint to gain access.
OmniPass Authentication Toolbar
After installing OmniPass and restarting, you will notice a dialog you have not seen before at Windows Logon. This is the OmniPass Authentication Toolbar, and it is displayed whenever the OmniPass authentication system is invoked. The OmniPass authentication system may be invoked frequently: during Windows Logon, during OmniPass Logon, when unlocking your workstation, when resuming from standby or hibernate, when unlocking a password-enabled screensaver, during pass­word replacement for remembered site or application logins, and more. When you see this toolbar, OmniPass is prompting you to authenticate.
The Logon Authentication window indicates what OmniPass-restricted function you are attempting. The icons in the lower left (fingerprint and key) show what authentication methods are available to you. Selected authentication methods are highlighted while unselected methods are not. When you click the icon for an unse­lected authentication method, the authentication prompt associated with that method is displayed.
When prompted to authenticate, you must supply the appropriate credentials: an enrolled finger for the finger­print capture window or your master password for the master password prompt (the key icon).
Remembering a Password
OmniPass can remember any application, GUI, or pass­word protected resource that has a password prompt.
Using the following procedure, you can store a set of credentials into OmniPass. These credentials will then be linked to your “master password” or fingerprint.
101
P7120.book Page 102 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Appendix
Go to a site that requires a login (username and pass­word), but do not log in yet. At the site login prompt, enter your username and password in the prompted fields, but do not enter the site (do not hit [Enter], [Submit], [OK], or Login). Right-click the OmniPass system tray icon and select Remember Password from the submenu. The Windows arrow cursor will change to a golden key OmniPass cursor. Click this OmniPass cursor in the login prompt area, but do not click the [Login] or [Submit] button.
Associating a Friendly Name
After clicking the OmniPass key cursor near the login prompt, OmniPass will prompt you to enter a “friendly name” for this site. You should enter something that reminds you of the website, the company, or the service you are logging into. In its secure database, OmniPass associates this friendly name with this website.
Additional Settings for Remembering a Site
When OmniPass prompts you to enter a “friendly name” you also have the opportunity to set how OmniPass authenticates you to this site. There are three effective settings for how OmniPass handles a remembered site.
The default setting is Automatically click the “OK” or
“Submit” button for this password protected site once the user is authenticated. With this setting, each time
you navigate to this site OmniPass will prompt you for your master password or fingerprint authentication device. Once you have authenticated with OmniPass, you will automatically be logged into the site.
Click Finish to complete the remember password proce­dure. The site location, the credentials to access the site, and the OmniPass authentication settings for the site are now stored in the OmniPass secure database. The OmniPass authentication settings (Settings for this Pass- word Site) can always be changed in Vault Management.
Logging in to a Remembered Site
Whether or not OmniPass prompts you to authenticate when you return to a remembered site is determined by
Settings for this Password Site and can be changed in Vault Management.
The following cases are applicable to using OmniPass to login to: Windows, remembered web sites, and all other password protected resources.
With Master Password
Once you return to a site you have remembered with OmniPass, you may be presented with a master pass­word prompt. Enter your master password and you will be allowed into the site.
Logging into Windows with a Fingerprint Device
When logging into Windows with a fingerprint device, the fingerprint capture window will now appear next to the Windows Login screen. Place your enrolled fingertip on the sensor to authenticate. You will be simultaneously logged into Windows and OmniPass. The capture window will also appear if you have used Ctrl-Alt-Del to lock a system, and the fingerprint device can be used to log back in as stated above.
Less secure is the option to Automatically enter this
password protected site when it is activated. Do not prompt for authentication. Check the upper box to get
this setting, and each time you navigate to this site OmniPass will log you into the site without prompting you to authenticate
.
This setting is more convenient in that whenever you go to a site remembered with this setting, you will bypass any authentication procedure and gain instant access to the site. But should you leave your system unattended with your OmniPass user logged in, anyone using your system can browse to your password protected sites and gain automatic access.
If you uncheck both boxes in Settings for this Password Site, OmniPass will prompt you for your master pass-
word or fingerprint authentication device. Once you have authenticated with OmniPass your credentials will be filled in to the site login prompt, but you will have to click the website [OK], [Submit], or [Login] button to gain access to the site.
102
If a machine is locked and OmniPass detects a different user logging back in with a fingerprint, the first user will be logged out and the second user logged in.
In Windows XP, your login options must be set either for classic login, or for fast user switching and logon screen to be enabled to use your fingerprint to log on to Windows. To change this go to Control Panel, select
User Accounts and then click Change the way users log on or off. If your Windows screensaver is password
protected, the fingerprint capture window will now appear next to screensaver password dialog during resume. You can authenticate to your screensaver pass­word prompt with your enrolled finger.
Password Management
OmniPass provides an interface that lets you manage your passwords. To access this GUI, double-click the OmniPass key in the system tray. Click Va u lt Ma n ag e- ment; you will be prompted to authenticate. Once you gain access to Vault Management, click Manage Pass-
words under Vault Settings. You will see the Manage Passwords interface, with a list of friendly names.
P7120.book Page 103 Monday, October 10, 2005 4:38 PM
Using the Fingerprint Sensor
You can view the credentials stored for any remembered website by highlighting the desired resource under Pass- word Protected Dialog and clicking Unmask Values. Should a password be reset, or an account expire, you can remove stored credentials from OmniPass. Highlight the desired resource under Password Protected Dialog and click Delete Page. You will be prompted to confirm the password deletion.
The two check boxes in Manage Passwords govern whether OmniPass prompts you to authenticate or directly logs you into the remembered site.
OmniPass will overwrite an old set of credentials for a website if you attempt to use Remember Password on an already remembered site.
The exception to the above rule is the resetting of your Windows password. If your password is reset in Windows, then the next time you login to Windows, OmniPass will detect the password change and prompt you to “Update” or “Reconfirm” your password with OmniPass. Enter your new Windows password in the prompt(s) and click OK and your OmniPass "master password" will still be your Windows password.
OmniPass User Identities
Identities allow OmniPass users to have multiple accounts to the same site (e.g., bob@biblomail.com and boballen@biblomail.com). If OmniPass did not provide you identities, you would be limited to remembering one account per site.
To create and manage identities, double-click the OmniPass key in the system tray. Click Vaul t Ma na ge - ment; OmniPass will prompt you to authenticate. Once you gain access to Vault Management, click Manage Identities under Vault Settings. You can only manage the identities of the currently logged in OmniPass user
To add a new identity, click New Identity or double-click Click here to add a new identity. Name the new identity and click [OK], then click [Apply]. You can now switch to the new identity and start remembering passwords.
To delete an identity, highlight the identity you want to delete and click [Delete Identity], then click [Apply]
When you delete an identity, all of its associated remembered sites and password protected dialogs are lost.
.
To set the default identity, highlight the identity you want as default and click [Set as Default]; click [Apply] to ensure the settings are saved. If you log in to OmniPass with a fingerprint device, you will automati­cally be logged in to the default identity for that OmniPass user. You can choose the identity with which you are logging in if you login using "master password".
Choosing User Identity during Login
To choose your identity during login, type your user­name in the User Name: field. Press [Tab] and see that the Domain: field self-populates. Click the Password: field to bring the cursor to it, and you will see the pull­down menu in the Identity: field. Select the identity you wish to login as and then click OK to login.
Switch User Identity
To switch identities at any time, right-click the OmniPass system tray icon and click Switch User Iden- tity from the submenu. The Switch Identity dialog will appear. Select the desired identity and then click OK.
Identities and Password Management
On the Manage Passwords interface of the Va u l t Management tab of the OmniPass Control Center, there
is a pull-down selection box labeled, Identity. This field lets you choose which identity you are managing pass­words for. When you select an identity here, only those password protected dialogs that are associated with that identity are shown. You can perform all the functions explained in “Password Management” on page 102.
CONFIGURING OMNIPASS
This section gives an overview of both the Export/ Import function and the OmniPass Control Center.
Exporting and Importing Users
Using the OmniPass Control Center, you can export and import users in and out of OmniPass. The export process backs up all remembered sites, credentials, and any enrolled fingerprints for an OmniPass user. All OmniPass data for a user is backed up to a single encrypted database file. During the import process, the Windows login of the exported user is required. If the proper credentials cannot be supplied, the user profile will not be imported
.
You should periodically export your user profile and store it in a safe place. If anything happens to your system, you can import your OmniPass profile to a new system and have all your remem­bered settings and fingerprints instantly.
You don't forget the Windows login credentials when exporting. When you examine the importation, you are prompted for authentication. The credentials that will allow a user profile to be imported are the Windows login credentials of the exported user. They are the credentials that had to be submitted when the user profile was exported. You will need User Name, Password, and Domai
n.
103
P7120.book Page 104 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Appendix
Exporting an OmniPass User Profile
To export a user, open the OmniPass Control Center, and click Import/Export User under Manage Users.
Click Exports an OmniPass user profile. OmniPass will prompt you to authenticate. Upon successfully authenti­cation, you must name the OmniPass user profile and decide where to save it. An .opi file is generated, and you should store a copy of it in a safe place.
This .opi file contains all your user specific OmniPass data, and it is both encrypted and password protected. This user profile does NOT contain any of your encrypted data files.
Importing an OmniPass User Profile
You cannot import a user into OmniPass if there already is a user with the same name enrolled in OmniPass.
To import an OmniPass user open the OmniPass Control Center, and click Import/Export User under Manage Users. Click Imports a new user into OmniPass and then select OmniPass Import/Export File (*.opi) and click Next. OmniPass will then prompt you to browse for the file you had previously exported (.opi file). When you select the .opi file for importation, OmniPass will prompt you for authentication. The credentials that will allow a user profile to be imported are the Windows login credentials of the exported user. They are the credentials that had to be submitted when the user profile was exported. You will need User Name, Password, and Domain. If you don’t remember the value for Domain, in a PC or SOHO environment Domain should be your computer name.
OmniPass will notify you if the user was successfully imported.
Things to Know Regarding Import/Export
Assume you export a local Windows User profile from OmniPass. You want to import that profile to another machine that has OmniPass. Before you can import the profile, a Windows user with the same login cre­dentials must be created on the machine importing the profile.
Example: I have a Windows user with the username “Tom” and the password “Sunshine” on my system. I have enrolled Tom into OmniPass and remembered passwords. I want to take all my passwords to new sys­tem. I export Tom’s OmniPass user profile. I go to my new system and using the Control Panel I create a user with the username "Tom" and the password "Sun­shine". I can now successfully import the OmniPass user data to the new system.
If you export an OmniPass-only user, you can import that user to any computer running OmniPass, pro­vided that a user with that name is not already enrolled in OmniPass.
If you attempt to import a user profile who has the same name as a user already enrolled in OmniPass, the OmniPass import function will fail.
OMNIPASS CONTROL CENTER
This section will serve to explain functions within the OmniPass Control Center that weren’t explained earlier.
You can access the OmniPass Control Center any of three ways:
Double-click the golden OmniPass key shaped icon in the Windows taskbar (typically in the lower-right cor­ner of the desktop)
Click the Start button; select the Programs group; select the Softex program group; and click the OmniPass Control Center selection.
Open the Windows Control Panel (accessible via Start button --> Settings --> Control Panel) and double- click the Softex OmniPass icon.
User Management
The User Management tab has two major interfaces: Add/Remove User and Import/Export User. Import/ Export User functionality is documented in “Exporting and Importing Users” on page 103. Add/Remove User functionality is straightforward.
If you click Adds a new user to OmniPass you will start the OmniPass Enrollment Wizard. The Enrollment Wizard is documented in “User Enrollment” on page 100.
If you click Removes a user from OmniPass, OmniPass will prompt you to authenticate. Authenticate with the credentials (or enrolled fingerprint) of the user you wish to remove. OmniPass will prompt you to confirm user removal. Click OK to complete user removal
Removing a user will automatically destroy all OmniPass data associated with that user. All identities and credentials associated with the user will be lost.
If you are sure about removing the user, we recommend you export the user profile.
User Settings
The User Settings tab has four interfaces: Audio Settings, Tas k ba r Ti p s, and Enrollment. User settings allow users
to customize OmniPass to suit their individual prefer­ences. Under User Settings (Audio Settings and Ta s k b a r Tips) you can set how OmniPass notifies the user of OmniPass events (e.g., successful login, access denied,
.
104
P7120.book Page 105 Monday, October 10, 2005 4:38 PM
Using the Fingerprint Sensor
etc.). The details of each setting under the Audio Settings and Tas k ba r T i ps interfaces are self-explana-
tory.
The Enrollment interface allows you to enroll finger­prints. For the procedure to enroll and authentication device refer to Chapter 2.3. To enroll additional finger­prints, click Enroll Authentication Device, and authen- ticate with OmniPass. Select the fingerprint recognition device in the Select Authentication Device screen (it should already be marked by a green check if you have a finger enrolled) and click Next.
System Settings
The OmniPass Startup Options interface can be found in the System Settings tab. With these options you can specify how your OmniPass Logon is tied to your Windows Logon.
The first option, Automatically log on to OmniPass as the current user, will do just as it says; during Windows login, you will be logged on to OmniPass using your Windows login credentials. If the user logging into Windows was never enrolled into OmniPass, upon login no one will be logged on to OmniPass. This setting is appropriate for an office setting or any setting where users must enter a username and password to log into a computer. This is the default setting.
With the second option, Manually log on to OmniPass at startup, OmniPass will prompt you to login once you have logged on to Windows.
With the third option, Do not log on to OmniPass at startup, OmniPass will not prompt for a user to be logged on.
You can manually log on to OmniPass by right-clicking the OmniPass taskbar icon and clicking Log in User from the right-click menu.
TROUBLESHOOTING
You cannot use OmniPass to create Windows users. You must first create the Windows user, and you will need administrative privileges to do that. Once the Windows user is created, you can add that user to OmniPass using the same username and password
Cannot add Windows users to OmniPass
If you experience difficulties adding a Windows user to OmniPass, you may need to adjust your local secu­rity settings. You can do this by going to Start,
Control Panel, Administrative Tools, and Local Security Settings. Expand Local Policies, expand Security Options, and double-click Network Access: Sharing and Security Model for Local Accounts. The
correct setting should be Classic - Local Users Authen­ticate as Themselves.
Cannot add a User with a Blank Password to OmniPass
If you experience difficulties adding a user with a
blank password to OmniPass, you may need to adjust your local security settings. First attempt the proce­dure explained in the Cannot add Windows user to OmniPass section. If the difficulties persist, then try the following procedure.
Click Start, Control Panel, Administrative Tools,
and Local Security Settings. Expand Local Policies, expand Security Options, and double-click
Accounts: Limit local account use of blank pass­words to console login only. This setting should be
set to Disabled.
Dialog appears after OmniPass authentication during Windows Logon
After installing OmniPass on your system, you can choose to logon to Windows using OmniPass. You authenticate with OmniPass (via master password, or an enrolled security device) and OmniPass logs you into Windows. You may, during this OmniPass authentication, see a Login Error dialog box.
This dialog box occurs when OmniPass was unable to log you into Windows with the credentials supplied (username and password). This could happen for any of the following reasons:
Your Windows password has changed
Your Windows account has been disabled
If you are having difficulties due to the first reason, you will need to update OmniPass with your changed Windows account password. Click Update Password and you will be prompted with a dialog to reconfirm your password.
Enter the new password to your Windows user account and click OK. If the error persists, then it is unlikely the problem is due to your Windows user account password changing.
105
P7120.book Page 106 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook – Appendix
106
P7120.book Page 107 Monday, October 10, 2005 4:38 PM
Index
Index
A
AC
adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23, 93
plug adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Auto Insert Notification . . . . . . . . . . . . . . . . . . . . . . . 36
Auto/Airline Adapter . . . . . . . . . . . . . . . . . . . . . . 23, 93
Automatically Downloading Driver Updates . . . . . . 76
B
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
battery bay release button . . . . . . . . . . . . . . . . . . . 11
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
charging indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 12
conserving power . . . . . . . . . . . . . . . . . . . . . . . . . . 27
increasing life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
level indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
lithium ion battery . . . . . . . . . . . . . . . . . . . . . . 31, 94
low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
shorted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
suspend mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
setup utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Where to Find Information . . . . . . . . . . . . . . . . . . 62
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
built-in microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
D
DC
output cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
power jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 23
Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Disk care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6, 24
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Dolby Headphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Drivers and Application Restore CD . . . . . . . . . . . . .75
DVD/CD-RW drive
control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
tray release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
DVD-RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
E
ECO Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Extended Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
External Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . .33
External Monitor Port . . . . . . . . . . . . . . . . . . . . . . .8, 44
C
Cache Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
CapsLock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Click Me! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cold-swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Cursor control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
F
FDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26, 76, 87
Fingerprint Sensor Device . . . . . . . . . . . . . . . . . . . . . .99
enrolling a fingerprint . . . . . . . . . . . . . . . . . . . . . .101
getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
installing OmniPass . . . . . . . . . . . . . . . . . . . . . . . . .99
logging into a remembered site . . . . . . . . . . . . . . .102
OmniPass authentication toolbar . . . . . . . . . . . . .101
password replacement . . . . . . . . . . . . . . . . . . . . . .101
remembering a password . . . . . . . . . . . . . . . . . . . .101
uninstalling OmniPass . . . . . . . . . . . . . . . . . . . . . .100
user enrollment . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
using OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . .101
107
P7120.book Page 108 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook
Firewire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 43
Flexible bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 18
cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
hot-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
release latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Floppy Disk
ejecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
formatting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
preparing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
write protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Floppy Disk Drive
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Fujitsu Driver Update utility . . . . . . . . . . . . . 26, 76, 87
Fujitsu HotKey Utility . . . . . . . . . . . . . . . . . . . . . . . . 87
Fujitsu LifeBook
care and maintenance . . . . . . . . . . . . . . . . . . . . . . . 79
traveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Function Key
F10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
F3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
F4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
F5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
F6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
F7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
F8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
F9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Fn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
G
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
H
Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Hard Disk/CD Access Indicator . . . . . . . . . . . . . . . . . 12
Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 43
Hibernation Feature . . . . . . . . . . . . . . . . . . . . . . . . . . 28
disable/enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Hot-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
I
IEEE 1394 port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 43
Integrated Wireless LAN . . . . . . . . . . . . . . . . . . . . . . 45
Internal LAN port . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
K
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6, 13
cursor keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
key indicator lights . . . . . . . . . . . . . . . . . . . . . . . . . .13
numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
L
LAN (RJ-45) port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
LifeBook P7000 notebook . . . . . . . . . . . . . . . . . . . . . . .5
unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Lithium ion Battery . . . . . . . . . . . . . . . . . . . . . . . . . . .11
M
Memory
capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Memory Module Cover . . . . . . . . . . . . . . . . . . . . . . . .11
Memory Stick/SD Card . . . . . . . . . . . . . . . . . . . . . . . . .9
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 38
Memory Upgrade Module . . . . . . . . . . . . . . . . . . . . . .40
Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . .6, 44
Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
result codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Modular Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
N
Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
NumLk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
O
Optical Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
DVD/CD-RW combo . . . . . . . . . . . . . . . . . . . . . . .34
emergency tray release . . . . . . . . . . . . . . . . . . . . . . .36
Multi-Format DVD Writer . . . . . . . . . . . . . . . . . . .34
software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
108
P7120.book Page 109 Monday, October 10, 2005 4:38 PM
Index
P
PC Card
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
POST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73, 95
error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Power
AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
auto/airline adapter . . . . . . . . . . . . . . . . . . . . . . . . 23
management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Power On Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Pre-Installed Software . . . . . . . . . . . . . . . . . . . . . . . . . 87
Adobe Acrobat Reader . . . . . . . . . . . . . . . . . . . . . . 87
manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Norton AntiVirus 2004 . . . . . . . . . . . . . . . . . . . . . 87
Quicken New User Edition . . . . . . . . . . . . . . . . . . 87
tutorials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Pre-installed Software
restoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
PS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
R
Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . 89
Re-Installing Individual Drivers and Applications . 75
Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Restoring software . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Restoring the Factory Image . . . . . . . . . . . . . . . . . . . 75
RJ-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 42
RJ-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 42
S
ScrLk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SD Card
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Secure Digital Card
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
device ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
dimensions and weight . . . . . . . . . . . . . . . . . . . . . .86
environmental requirements . . . . . . . . . . . . . . . . . .86
features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
mass storage device options . . . . . . . . . . . . . . . . . . .85
memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
MS Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
popular accessories . . . . . . . . . . . . . . . . . . . . . . . . . .86
power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Status Indicator Panel . . . . . . . . . . . . . . . . . . . . . . . .6, 12
Stereo Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Suspend/Resume/Power On Button . . . . . . . . . . . .6, 27
S-Video Out Port . . . . . . . . . . . . . . . . . . . . . . . . . . .8, 43
Swapping batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .85
T
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
double-clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
pointing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
scroll button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
scrolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
built-in speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
display panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
DVD/CD-RW drive . . . . . . . . . . . . . . . . . . . . . . . . .66
hard disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
identifying the problem . . . . . . . . . . . . . . . . . . . . . .65
keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
mouse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
PC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68, 69
power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69, 70
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Troubleshooting Table . . . . . . . . . . . . . . . . . . . . . . . . .66
109
P7120.book Page 110 Monday, October 10, 2005 4:38 PM
LifeBook P7000 Notebook
U
Universal Serial Bus Ports . . . . . . . . . . . . . . . . . . . . . . 43
USB
ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 9, 43
V
Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
W
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
application key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
start keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wireless LAN
access point (infrastructure) mode . . . . . . . . . . . . 49
activating the WLAN device . . . . . . . . . . . . . . . . . 50
ad hoc mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
before using the wireless LAN . . . . . . . . . . . . . . . . 48
configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
deactivating the WLAN device . . . . . . . . . . . . . . . 49
Devices covered by this document . . . . . . . . . . . . 48
IP address information . . . . . . . . . . . . . . . . . . . . . . 60
modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
on/off switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
using Atheros Client Utility software . . . . . . . . . . 52
using Intel PROSet software . . . . . . . . . . . . . . . . . 51
wireless LAN glossary . . . . . . . . . . . . . . . . . . . . . . . 58
wireless network considerations . . . . . . . . . . . . . . 49
110
P7120.book Page 111 Monday, October 10, 2005 4:38 PM
P7120.book Page 112 Monday, October 10, 2005 4:38 PM
Loading...