Fujitsu Client Computing BPAD06, BPAD05 Users Manual

SAFETY STATEMENT

KD91316-L194

FUJITSU LIMITED

1-1, Kamikodanaka 4-chome, Nakahara-ku, Kawasaki
211-8588, JAPAN

Introduction

Congratulations on purchasing B-PAD Mobile computer. For your
Safety ,please read this statement carefully before using B-PAD.

This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
End-users must be provided with specific operating instructions for
satisfying RF exposure compliance.

JUL. 2007 Second Edition

Standard for the FCC/IC conformity

This equipment has been tested and found to comply with the limits
for a Class B digital device pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is required to correct the interference
by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.

- Consult the dealer or an experienced radio/television technician for

help.
This device complies with Part 15 of FCC Rules and RSS-Gen of IC
Rules. Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired
operation of this device.

This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.

The available scientific evidence does not show that any health
problems are associated with using low power wireless devices.
There is no proof, however, that these low power wireless devices
are absolutely safe. Low power Wireless devices emit low levels of
radio frequency energy (RF) in the microwave range while being
used. Whereas high levels of RF can produce health effects (by
heating tissue), exposure to low-level RF that does not produce
heating effects causes no known adverse health effects. Many
studies of low-level RF exposures have not found any biological
effects. Some studies have suggested that some biological effects
might occur, but such findings have not been confirmed by additional
research. B-PAD has been tested and found to comply with FCC/IC
radiation exposure limits set forth for an uncontrolled equipment and
meets the FCC radio frequency (RF) Exposure Guidelines in Supplement

C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules

FCC WARNING

Change or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.

CE marking

(1999/5/EC)

This product follows the provisions of the European Directive
1999/5/EC.

RF Devices

Fujitsu’s RF products are designed to be compliant with the rules and
regulations in the locations into which they are sold and are labeled
as required. The majority of Fujitsu’s RF devices are type approved
and do not require the user to obtain license or authorization before
using the equipment. Any changes or modification to Fujitsu
equipment, not expressly approved by Fujitsu, could void the user’s
authority to operate the equipment.

Laser Devices

This product contains a Class 2 laser and complies with US
21CFR1040.10. These type of lasers use a low power visible light
diode. Care should be taken to avoid staring directly into the light.
Laser power up to 1.2 mW at 650nm could be accessible in the
interior.

“CAUTION – Use of controls or adjustments or performance of
procedures other than those
specified herein may result in hazardous laser light exposure.”

WARNING – Do not looking into the reading aperture while a
scanning beam is being emitted. Doing so can injure the eyes.

Scanner Safety Labeling

CAUTION: LASER

When using the laser scanner, do not direct the laser
beam toward anyone’s eyes. Doing so may injure the
eyes.
Do not look into the aperture of the laser scanner.
Because a laser beam is emitted from the aperture,
you may injure your eyes.

t

WARNING

GENERAL

INHIBITION

DISASSEMBLY

PROHIBITED

FIRE

Use only the specially designed cradle, AC adapter,
and single-pack charger. If another item is used,
differences in voltage or current can damage the
B-PAD. If the battery is not handled correctly , the
B-PAD may overheat, explode, or catch fire.
Be sure to observe the following precautions.

-Neither throw the battery into a fire or heat it.

-Connect the terminals correctly.

-Do not connect the terminals using a wire or other
metal material.

-Do not carry or store the battery with any metal
materials, such as necklaces or hair pins.

-Do not puncture the battery with a needle, hit it with a
hammer, stomp on it, or otherwise apply a strong
shock to it.

-Do not disassemble or modify the battery.

-Do not use or leave the battery near a flame, fire,
stove, or other source of heat, in direct sunlight, or in a
car exposed to sunlight.

-Do not put the battery in a microwave oven or other
hot con

ainer.

-Charge the battery only on the special cradle or

single-pack charger.

-Do not charge the battery by directly connecting it to
a wall outlet or cigarette lighter in a car.

-Do not charge the battery near a flame, fire or under
the blazing sun.

-Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer's instructions.

If the B-PAD generates heat, smoke, or an usual
smell or noise, turn off the power immediately and
contact maintenance personnel. Failure to do so may
result in an electric shock or fire.

Do not modify the B-PAD without permission.
Doing so may result in an electric shock or fire.
Do not disassemble or remove any components as
this will emit laser beams. Maintenance involving the
B-PAD internal functions is not necessary.

Warning Indications and Symbols

This note uses warning indications and symbols to help users use
the B-PAD safely and to prevent personal injury and property
damage.
This manual uses warning indications and symbols in the text to
indicate safety conditions. The meaning of each indication and
symbol is explained below.

Warning Indications

Indicates a hazardous situation that could

WARNING

result in personal injury if the user does not
perform the procedure correctly.

Indicates a hazardous situation that could

CAUTION

result in minor or moderate personal injury if
the user does not perform the procedure
correctly. Also indicates that damage to
the product or other property could occur if
the user does not perform the procedure
correctly.

Warning Symbols

ELECTRIC SHOCK

GENERAL

INHIBITION

GENERAL
CAUTION

FIRE

DISASSEMBLY

PROHIBITED

UNPLUG

THE CABLE

Indicates the possibility of injury
from an electric shock.

Indicates a condition that
requires caution and a specific
action that must not be
performed.

Indicates a condition that requires general caution.

Indicates the possibility of an electric shock or fire.

Indicates an action that is
prohibited (prohibited action).

Indicates a required action.