Fujitsu x178 User Manual

Display Unit

Fujitsu x178

User’s Guide

Brugervejledning

Käyttäjän käsikirja

Manuel d’utilisation

Benutzerhandbuch

Manual do utilizador

Guía de usuario

Användarhandbok

Display Unit Fujitsu x178
User’s Guide

First Edition Document Number:
August 1999

This document was produced by Fujitsu Computers Oy in Espoo, Finland.
If you have comments or suggestions, we’d like to hear from you!

Mail: Internet:
Fujitsu Computers Oy [e-mail]
User Documentation
PO Box 10 X.400:
FIN-02611 Espoo G=user S=documentation
Finland O=fujitsu OU1=fin1703

P=fujitsu A=elisa C=fi

Fujitsu Computers Ltd (hereinafter Fujitsu) endeavours to ensure that the information
in this document is correct, but accepts no liability for any error or omission in the
same.
Any procedures described in this document for operating Fujitsu products should be
read and understood by the operator before such products are used. To ensure that
Fujitsu products function without risk to safety or health, such procedures should be
strictly observed by the operator.
The development of Fujitsu products and services is continuous and published
information may not be up to date. Any particular issue of a product may contain part
only of the facilities described in this document or may contain facilities not described
herein. It is important to check the current position with Fujitsu.
Specifications and statements as to performance in this document are Fujitsu estimates
intended for general guidance. They may require adjustment in particular
circumstances and should therefore not be taken as formal offers or commitments.
Statements in this document are not part of a contract or program product licence
save insofar as they are incorporated into a contract or licence by express written
reference. Issue of this document does not entitle the recipient to access to or use of
the products described, and such access or use may be subject to separate contracts or
licences.

Microsoft, Windows, Windows NT and the Windows logo are registered trademarks
of Microsoft Corporation in the United States and other countries. Other products
mentioned may be trademarks or registered trademarks of their respective owners.

ENERGY STAR is a U.S. registered trademark.

©Copyright Fujitsu Computers Ltd 1998

Contents

Contents

Your new display unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Selecting a suitable location . . . . . . . . . . . . . . . . . . . . . . . 5

Installing your display unit . . . . . . . . . . . . . . . . . . . . . . . . 6

Display power management . . . . . . . . . . . . . . . . . . . . . . . . 8

Adjusting the picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Cleaning your display unit . . . . . . . . . . . . . . . . . . . . . . . . . 14

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Technical fact sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Your new display unit

Your new display unit is a highly ergonomic colour display unit

■ supporting high screen refresh rates and full scan flicker-free

picture quality

■ allowing easy setup through Plug-and-Play

■ with On Screen Display menus for user control

■ complying with MPR90 and TCO92 recommendations for low

electromagnetic fields

■ meeting TCO’99 environmental specifications

■ with power management features that allow the unit to enter a

low power consumption state after a period of inactivity.

When you unpack the display unit, check to make sure that you have
the items below. Apower cable is included in your system unit
package.

English

3

Safety information

When you set up and use your display unit, follow the safety
instructions below.

Do not use a continental European type power cable in the
United Kingdom and Denmark. Use a 3-prong plug to ensure
an earthed connection.

This equipment must be connected to an earthed outlet which
is close to the display unit and accessible in case you need to
disconnect the display.

■

Do not connect an extension cord.
If you need to replace your cords, contact your Fujitsu sales

■

representative.
Do not under any circumstances open the display unit cabinet.

■

Slots in the cabinet are provided for ventilation. Do not block

■

the ventilation slots in the display unit cabinet.

English

4

Selecting a suitable location

■

Place the display unit at least 30 cm from other electrical or
heat-emitting equipment and allow at least 10 cm on each side
for ventilatiion.

■

Place the display unit in a position where no light shines
directly onto or is reflected on the screen.

■

To reduce eye strain, avoid installing the display unit against a
bright background such as a window.

■

Place your display unit at a comfortable viewing height and
distance: most people prefer the top line of the text to be at or

just below eye level and the display within arm’s length (a
distance of 45 to 90 cm) when you are comfortably seated. You

can tilt and swivel the display unit to get a good viewing angle.

■

This display unit has an anti-glare antistatic screen. The use of
an additional anti-glare screen is not recommended as it will
impair picture quality.

English

5

Installing your display unit

WARNING!

Before you start cabling your display unit, check that the
power is off on all units. To avoid any possibility of electric
shock, always connect your equipment to properly earthed
outlets.

The base of the display is already installed; do not use the

1 .

monitor withour it. Place the display unit on a level and sturdy
surface.

Connect the display unit’s signal cable (a) to the system unit

2 .

and scure it with the two screws. The connector pins may be
protected against damage by a plastic cover which needs to
be removed first.

Plug the display unit’s power cable (b) first to the back of the

3 .

display unit, as shown below.

Then plug the power cable ( b) to a 100V-240V earthed

4 .

electrical outlet or to the system unit, if it has an outlet for the
display power cable, as shown below.

English

6

Turn on the display unit using the power switch (1) and check

5 .

to make sure that the power LED (2) is on, as shown below. If

not, repeat steps 2,3 and 4 or refer to the Troubleshooting

section of this guide.

Turn on the power to the computer. The picture will appear

6 .

within about 15 seconds. During its start-up the computer

recognizes the display automatically provided that the display

unit has been turned on. Adjust the picture to obtain optimum
picture quality. See the Adjusting the picture section in this
guide for more information.

English

7