Fujitsu SERVIS FW-D1008NP Quick Start Manual

SERVIS

p

TM

IP-KVM FW-D1008NP Quick Start Guide

Introduction

- Thank you for purchasing this product. This "Quick Start

Guide" describes the items contained in the packaging,

and explains the initial setup and procedures for basic

operations. Make sure to read this manual when using

the device.

- Read the "Safety Precautions" in the CD-ROM provided

with the device in advance for its correct use. The

"Safety Precautions" includes indications to obviate any

chance of accident or damage to you and people near

you, and your property.

- For details on operations, refer to the Installer/User

Guide

Step 1 Checking the Components

Check that the following items are contained in the

packaging.

- The device

- Power cables

- Serial Cable … 1

- Flanges … 2

- Screws for flange …4

- CD-ROM …1

- Warranty certificate … 1

- License information … 1

- China RoHS guide …1

- Quick Start Guide

rovided with the device.

3 pin plug-IEC320 socket (AC100V)…1
IEC320 plug-IEC320 (AC200V)…1

Installer/User Guide
FW-Client Software

* This warranty is valid in Japan.

(Japanese, English) … 1 each

Step2 Connecting the Device

1. Connect the device as shown below.

2. When you have connected the device, turn on each

connected server first, and then the device.

Ethernet

Telephone

Power

Source

Modem

Local Connection

Server

Server

Network

Remote User

FW-D1008NP

Server

Server

Step3 Setting Up the Network

For the initial settings of the device, set the IP address by a local

operation.

1. The device starts operating

about 1 minute after it is

turned on, and the [Free] tag

appears in the monitor for

local connection.

2. Press the [PrintScreen] key

on the local keyboard once,

then the following Main

window appears. Click

[Setup].

3. The following Setup window

appears. Click [Network].

5. When you specify a fixed

IPv4 address, click the

"Static" and the "IPv4" radio

button, enter values in the IP

address, Netmask and

Gateway fields, and click the

[OK] button. (For DHCP,

select the corresponding

Opion.)

4. The following Network

window appears. Specify the

IP address here.

6. The following message

appears, and the device

restarts. If the [Free] tag is

shown 1 minute later, the

network setup is complete.

Step4 Installing FW-Client

By using the device, install "FW-Client" – a tool for managing the

target device – into the remote client’s PC. The following explains

how to install into a Windows computer.

1. Launch Setup.exe,

contained in the CD-ROM

provided with the device.

2. The following dialog box

appears. Click [OK].

3. The following dialog box

appears. Click [Next].

5. The contents of the dialog

box are shown as below.

Select the install destination,

and click [Next].

7. The following dialog box

appears. Click [YES].

9. When the contents of the

dialog box are shown as

below, the installation is

complete. Click [Done].

4. On the following dialog box, if

you agree with the statement,

select the corresponding option,

and click [Next].

6. The contents of the dialog box

are shown as below. To set an

icon on the desktop, select the

check box and click [Install].

8. The following dialog box is

shown, and installation starts.

(Continued to the reverse side)

<Inquiry about our products>

FUJITSU COMPONENT LIMITED Marketing Group

TEL: [phone]
E-mail: [e-mail] URL: http://www.fcl.fujitsu.com/en/

NC14013-0922RS-02

y

(Continued from the front page)

Step5 Setting Up FW-Client

Set up for operating the device and other target devices from

FW-Client.

1. Select [Start]→[Programs]

→ [Fujitsu Component

Limited FW Client]. Or,

double-click the [Fujitsu

Component Limited FW

Client] icon.

3. The following [New

Appliance Wizard] dialog

box appears. Click [Next].

5. Confirm the IP address

setting. If you have set up an

IP address for the device at

Step 3, Select [Yes, the

Appliance has an IP

address], and click [Next].

2. The following window

appears. To register the

device, click [New

Appliance].

4. Choose the product type.

Select [Other], and click

[Next].

6. Enter the IP address of the

device. Then click [Next].

7. The contents of the dialog

box are shown as below.

Search for the device from

the network.

9. The device is added to the

appliance list as shown

below.

8. The contents of the dialog

box are shown as below,

and the registration of the

device is completed.

Step6 Running an Update

Check the current connection status of a server module by

re-s

nchronizing FW-Client and the device.

1. Click the device registered in

the appliance list, and click

[Resync] shown at the

bottom.

2. The [Resync Appliance

Wizard] dialog box appears.

Click [Next].

3. On the following dialog box,

select the required check

box(es), and click [Next].

5. The updated information is

shown. The dialog box

below shows that a new

server module has been

detected. Click [Next].

4. The contents of the dialog

box are shown as below,

and data is retrieved from

the device.

6. The contents of the dialog

box are shown as below,

and the update is completed.

Step7 Access a Target Device

Perform an operation on a connected target device.

You need to install the version after 1.6 of JAVA Runtime

Environment (JRE) in the remote client PC to operate the target

device. Since JRE is stored in attached CD-ROM, please use it.

1. Click the [Servers] tab on the

FW-Client window, select

and double-click the server

module detected and

registered at Step6.

2. The following login dialog

box appears. Enter the

Username and password.

By default, "admin" is

registered both for the

Username and the

Password. After entering,

click [OK].

3. The following [Video Session Viewer] window appears, and

target device operations are enabled.

To finish, click [X] on the top right of the Video Session Viewer

window.

NOTES

Adjusting the mouse pointer speed on the server

When a remote user accesses a target server to perform an

operation, the mouse cursors on the remote user side and target

server side may not coincide. When this happens, adjust the

mouse pointer setting for the operating system on the target

server so that the two mouse cursors coincide.

Setup for Windows XP, Server 2003, Vista

-Click [Control Panel] → [Mouse] to show [Mouse Properties].

-Click the [Pointer Options] tab.

-In the [Select a pointer speed] section, move the slider to the

middle. Clear the [Enhance pointer precision] check box.

-In the [Snap To] section, clear the [Automatically move pointer

to the default button in a dialog box] check box.

-Click the [OK] button to finish.

For software setup or details on operations, refer to
the Installer/User Guide in the CD-ROM provided
with the device.

<Inquiry about our products>

FUJITSU COMPONENT LIMITED Marketing Group

TEL: [phone]
E-mail: [e-mail] URL: http://www.fcl.fujitsu.com/en/

NC14013-0922RS-02