Fujitsu S26361-F3554-L8 Service Manual
Data Sheet FUJITSU D2607 SAS/SATA RAID controller
Data Sheet
FUJITSU D2607 SAS/SATA RAID controller
D2607 SAS 6Gb/s based on LSI MegaRAID® for internal storage devices
The RAID concept (Redundant Array of Independent
Disks) refers to several independent hard disks
which form a large logical drive when switched
together.
Redundancy information is calculated from
several data blocks (except for RAID 0) and saved
distributed to the individual hard disks. Your
operating system no longer accesses the individual
hard disks, but the array.
The actual objective of the RAID concept is to
increase availability and prevent downtimes in the
event of a hard disk failure. However, the theoretical
security of the RAID concept is only as good as
the RAID controller used. Benet from the Fujitsu
RAID controllers where technology, experience and
practical implementation all ensure the security that
your company needs in the event of an emergency.
D2607 SAS/SATA RAID controller
The Fujitsu D2607 SAS/SATA RAID controller, based
on the LSI SAS2008, offers small businesses exactly
the low-cost data safety unit which they have been
looking for.
The D2607 enables increased read/write
performance thanks to its RAID 0, 1 and 10
implementation.
Benet from the close alignment of the RAID
hardware system and the ServerView® RAID
Manager software which offers fast initialization for
quick array setup.
Enjoy the world of easy conguration – and time
and cost efciency that you have been searching for
– the Fujitsu D2607 RAID controller.
Main Features Benefits
6Gb/s SAS ports PCI Express® 2.0 x8 Connect up to 16 HDDs
LSISAS2008 6Gb/s RAID levels 0 and 1 for more data security
Increased Read/Write performance RAID spans 10
Data protection Auto resume after loss of system power during array rebuild or
reconstruction
User Management Options Seamless merging of the RAID management into system
management
Page 1 / 3 www.fujitsu.com/primergy
Data Sheet FUJITSU D2607 SAS/SATA RAID controller
Technical details
Technical details
Controller Silicon LSI SAS2008
Controller type RAID 0/1 Ctrl.
Operating system Information to released operating systems can be found in the server datasheets. Details can be found in the
released drivers list on the support portal.
Released drivers list link http://support.ts.fujitsu.com/Download/Index.asp
Number of ports 8 ports int.
8 ports ext.
Connector internal 2x SSF-8087
Data transfer rate up to 6 Gbit/s
Bus interface PCIe 2.0 x8
RAID Management ServerView RAID Manager
MegaCLI (command-line interface)
WebBIOS
Key RAID Data Protection Feature RAID levels 0, 1
RAID spans 10
Online RAID Level Migration (RLM)
Auto resume after loss of system power during array rebuild or reconstruction
Congurable stripe size up to 64KB
Fast initialization for quick array setup
Check Consistency for background data integrity - Make Data Consistent (MDC)
Patrol read for media scanning and repairing
16 logical drive support
Conguration on Disk (COD)
S.M.A.R.T support
RAID level 0, 1, 10
RAID cache backup unit No BBU support
RAID controller notes (based on LSI SAS2008)
Interface technology SAS/SATA
HDD SAS
Order code Product Name Number of Connectors Related product
S26361-F3554-E8 RAID Ctrl SAS 6G 0/1 (D2607) 2 PRIMERGY Server
S26361-F3554-L8 RAID Ctrl SAS 6G 0/1 (D2607) 2 PRIMERGY Server
S26361-F3976-E2 RAID Ctrl SAS 6G 0/1 (D2607) 2 CELSIUS Workstation
S26361-F3976-L2 RAID Ctrl SAS 6G 0/1 (D2607) 2 CELSIUS Workstation
Compliance
Compliance notes According to the corresponding system
Compliance link http://globalsp.ts.fujitsu.com/sites/certicates
Page 2 / 3 www.fujitsu.com/primergy
Loading...