• Care and Maintenance·········································44
Before using the display, read this manual carefully so that you know how to use the display correctly.
Refer to this manual whenever questions or problems about operation arise. Be sure to read and observe the safety precautions.
Keep this manual where the user can see it easily.
∗
Installation and removal require special expertise. Consult your product dealer for details.
FUJITSU GENERAL LIMITED
DECLARATION OF CONFORMITY
according to EN45014
We
Fujitsu General (Euro) GmbH
of
Werftstraße 20, D-40549 Düsseldorf, F. R. Germany
Manufacturer: Shinjyo Fujitsu General Limited
702-3 Kanezawa Shinjyo-shi
Yamagata Japan
declares under our sole responsibility that the product,
Type: 42” PLASMA DISPLAY
Model Name: PDS4207W-H/PDS4207E-H
to which this declaration relates are in conformity with the following standards;
European Standards:
EMC: a. EN55022 1994, Class A
b.EN61000-3-2 1995
c. EN61000-3-3 1995
d.EN50082-2 1995
By conformance with the standard referenced, the product follows
the provisions of the directives listed below.
a. EC Council Directive 89/336/EEC of 3rd, May 1989
b.EC Council Directive 92/31/EEC of 28th, April 1992
c. EC Council Directive 93/68/EEC of 22nd, July 1993
d.EC Council Directive 73/23/EEC of 19th, February 1973
Place of Issue: Germany
Date of Issue: Nov. 1998
Signature:
H. Hirosaki, Managing Director
Fujitsu General (Euro) GmbH
Declaration reference:Fujitsu General (Euro) GmbH
Werftstraße 20, D-40549 Düsseldorf, F. R. Germany
Tel: 0211-50098-0Fax: 0211-50098-50
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
IMPORTANT INFORMATION
WARNING: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
WARNING: TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE.
IMPORTANT SAFEGUARDS
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to
assure your personal safety . But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK ORFIRE HAZARD. In order not to defeat the safeguards incorporated into this product, observe the following
basic rules for its installation, use and service. Please read these “Important Safeguards” carefully before use.
–All the safety and operating instructions should be read before the product is operated.
–The safety and operating instructions should be retained for future reference.
ENGLISH
–All warnings on the product and in the operating instructions should be adhered to.
–All operating instructions should be followed.
–Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
–Do not use attachments not recommended by the product manufacturer as they may be hazardous.
–Do not use this product near water. Do not use immediately after moving from a low temperature to high
temperature, as this causes condensation, which may result in fire, electric shock, or other hazards.
–Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. The product should be mounted according to the
manufacturer’s instructions, and should use a mount recommended by the manufacturer.
–When the product is used on a cart, care should be taken to avoid quick stops, excessive force, and
uneven surfaces which may cause the product and cart to overturn, damaging equipment or
causing possible injury to the operator.
–Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the
product and protect it from overheating. These openings must not be blocked or covered. (The openings
should never be blocked by placing the product on bed, sofa, rug, or similar surface. It should not be
placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the
manufacturer’s instructions have been adhered to.)
For proper ventilation, separate the product from other equipment, which may prevent ventilation and keep
distance more than 10cm.
3
SAFETY PRECAUTIONS
–This product should be operated only with the type of power source indicated on the label. If you are not
sure of the type of power supply to your home, consult your product dealer or local power company.
–This product is equipped with a three-wire plug. This plug will fit only into a grounded power outlet. If you
are unable to insert the plug into the outlet, contact your electrician to install the proper outlet. Do not
defeat the safety purpose of the grounded plug.
–Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where
they exit from the product.
–For added protection of this product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent
damage to the product due to lightning and power line surges.
–Do not overload wall outlets, extension cords, or convenience receptacles on other equipment as this can
result in a risk of fire or electric shock.
–Never push objects of any kind into this product through openings as they may touch dangerous voltage
points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the
product.
–Do not attempt to service this product yourself as opening or removing covers may expose you to danger-
ous voltages and other hazards. Refer all service to qualified service personnel.
–Unplug this product from the wall outlet and refer service to qualified service personnel under the following
conditions:
a) When the power supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen on the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the Operation Manual, as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified technician to restore the product to
its normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance – this indicates a need for service.
4
–When replacement parts are required, be sure the service technician has used replacement parts speci-
fied by the manufacturer or with same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards.
–Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition.
–The product should be placed more than one foot away from heat sources such as radiators, heat regis-
ters, stoves, and other products (including amplifiers) that produce heat.
–When connecting other products such as VCR’s, and personal computers, you should turn off the power of
this product for protection against electric shock.
–Do not place combustibles behind the cooling fan. For example, cloth, paper, matches, aerosol cans or
gas lighters that present special hazards when over heated.
–Use only the accessory cord designed for this product to prevent shock.
The power supply voltage rating of this product is AC100-240 V, the power cord attached conforms to the
following power supply voltage. Use only the power cord designated by our dealer to ensure safety and
EMC.
When it is used by other power supply voltage,
power cable must be changed.
Consult your product dealer.
Power cord
ENGLISH
Power supply voltage: AC100-125V AC 200-240 V AC 240 V (SAA TYPE)
5
FEATURES
VERTICAL INSTALLATION
The dynamic vertical screen is obtained by installing the Plasmavision vertically.
PLASMAVISION SUPPORTS
The VGA full display and SVGA and XGA compression display suitable for personal computers
A VARIETY OF INPUT TERMINALS
The high quality image color difference signals such as DVD etc. can be input in addition to the video, S-video, and RGB.
CONVENIENT POWER MANAGEMENT FUNCTION
DPMS (Display Power Management Signaling) automatically minimizes power consumption.
FIVE TYPES OF WIDE DISPLAY
Five types of wide display are supported: WIDE 1, WIDE 2, ZOOM 1, ZOOM 2 and normal display (4:3).
6
ACCESSORIES
Cable clamper
(Attach as in the illustration.)
Bundle connecting cables so
that they lead downwards, as
in the illustration.
• The accessory cable clampers are for fastening the connected
signal cables and a power cable. When installing this display
on a wall or ceiling, insert the cable clampers into the holes on
the rear of the display.
Connecting to External Equipment
Cables for connecting external equipment must be
purchased separately.
Connectors
AUDIO INPUTPin jack
VIDEO INPUTBNC
S-VIDEO INPUTS terminal
COMPONENT VIDEO INPUT
RGB 1 INPUT15-pin mD-sub
RGB 2 INPUTBNC
RS-232C9-pin D-sub
∗ When connecting separately pur-
chased BNC terminals, conversion
connectors are required between the
pin jacks and the BNC terminals, so
purchase these also.
∗ Cables connecting the personal com-
puter vary according to the type of
machine, so consult your product
dealer.
BNC
Screw A (10 mm)
Screw B (20 mm)
7
WHAT YOU SHOULD KNOW
POINTS ABOUT USAGE
• When installing the display, use the optional desktop stand, wall-mounting unit, or ceiling mounting unit. Have
the installation done by your product dealer.
• When installing the display , refer to the installation manuals for the options. Further, be sure that the display does
not lean to the side or backward.
• Place the power cord and connection cables in a corner of the wall or floor so that they do not get caught on
anything.
• For good heat dissipation, the Plasmavision requires at least the space shown in the figure below.
• The installation location must have an ambient temperature range of 0 °C – 40 °C.
See page 41 for optional parts.
When desktop stand used
Front viewSide view
Upper
20 cm
15cm15cm
LeftRightWall
FloorFloor
Desktop stand
5 cm
5 cm
When wall-mounting unit used (horizontally) When ceiling-mounting
unit used
Front viewSide viewSide view
Upper
20 cm
Wall mounting unit
20 cm
Ceiling
mounting unit
Ceiling
10 cm
8
10 cm
Lower
10 cm
RightWallLeft
5 cm
Wall
5 cm
When wall-mounting unit used (vertically)
Front viewSide view
Upper
15 cm
LeftRight
10 cm
Lower
10 cm10 cm
Power lamp
Wall mounting
(vertical usage)
5 cm
ENGLISH
Wall
• When mounting the Plasmavision vertically, make sure that the power lamp is at the lower right.
Notes
• Do not display the same picture (pattern) continuously for a long time. Doing so raises the brightness of the picture and may
cause after-images.
• Looking at the picture continuously for a long time can tire the eyes. View the display from a reasonable distance (about three
times the length of the screen).
∗
If something is wrong with the Plasmavision internally, the built-in protection circuit will cut the power automatically. If so, the
power lamp will blink in red, indicating a malfunction.
• If the power lamp is blinking red, it is warning that something is wrong with the Plasmavision. There is a danger of fire or
electrical shock, so be certain to unplug the power cord and contact your product dealer. (See P44)
• The plasma display panel has been built using extremely precise and sophisticated technologies. More than 99.99% of its
pixels are effective. However, a minute number of pixels are missing or constantly lit.
• Do not install the Plasmavision where there will be interference between it and other AV equipment. (If interference from
electromagnetic waves causes jumbled images, noise or malfunctioning of the infrared remote control, change the installation
location.)
• When the display is installed vertically, only still images appears.
9
PREVENTING EQUIPMENT FROM FALLING
To prevent accidents and to ensure safety during disasters such as earthquakes, take precautions to ensure
that the equipment cannot topple over.
ATTACHING TO WALL OR COLUMN
• Remove the display cover from both sides. Then, for both left and right sides, use screw A (10 mm) to attach
bracket A to the screw hole (highest of the five holes on the side).
• For both left and right sides, use screw B (20 mm) to attach bracket B to the wall. Then tie brackets A and B with
a strong rope so that the display panel does not topple over.
• This arrangement is stable when the rope is horizontal or pulled downward.
How to remove display cover
Push,
then pull
the cover
with the
fingers.
Strong rope (not supplied)
Display cover
Screw A (10 mm)
Display cover
Bracket ABracket B
Display
Screw B (20 mm)
ATTACHING TO DESKTOP STAND
• Fasten the screws supplied with the desktop stand into their holes at the rear of the desktop stand. (2 holes)
• For details, refer to P-42TT01 User‘s Manual for the desktop stand.
Two
places
Screw B (20 mm)
The screws are supplied with the desktop stand.
10
NAMES OF PARTS AND THEIR FUNCTIONS
Front viewBottom view
ENGLISH
1
Power lamp
• Shows the power status, ON or OFF.
• Lit (red)····Standby
• Lit (green)····Power on
• Blinking (red)····Internal abnormality. Be certain to
unplug the power cord.
2
Remote control receiver
• Receives the signals from the remote controller.
3
Operation panel
MENU
VOLUME
(ADJUST)
WIDE
(SET)
• POWER button: Switches the power on or off.
• MODE button: Selects the input mode.
• MENU button: For adjusting the video and audio to
your taste.
• VOLUME (ADJUST)
buttons: Normally used for adjusting the volume.
During adjustments, these buttons are
used for making adjustments from the
menu screen.
• WIDE (SET) button: Normally used for selecting the
desired wide screen.
During adjustments, this is the
(SET) button for setting the
menu screen.
4
Internal speakers
• Output the audio connected to the audio input termi-
nals.
11
NAMES OF PARTS AND THEIR FUNCTIONS
Rear view
RGB 2
SYNC SW
INPUTRS232C
INPUT
TTL
ANALOG
RGB HV
(75Ω)
AUDIO
INPUT
R
5
Power switch
RGB 1
VIDEO
S-VIDEO
CONPONENT-VIDEO
INPUT
INPUT
L
INPUT
Y Pb/B-Y Pr/R-Y
SYNC SW
TTL
ANALOG
(75Ω)
• When pressed, power lamp 1 lights red, and the
power can be turned on or off by the remote controller. When this switch is pressed again, the power is
cut and power lamp 1 goes off.
6
Power input terminal
• Firmly insert the accessory power cord as far as it will
go into the power input terminal.
• Firmly push the power cord plug as far as it will go
into the power socket. (100–240 VAC)
7
Video input terminal (VIDEO INPUT)
• Connects to the video output terminal of a video deck
or video disc player.
8
S video input terminal (S-VIDEO INPUT)
• Connects to the S video output terminal of a video
deck or video disc player.
9
Component video input terminal (COMPONENT
VIDEO INPUT)
• Connects to the component video output terminal of
DVD and similar devices.
10
RGB 1 input terminal (RGB 1 INPUT)
• Connects to the computer monitor's (analog RGB)
output terminal.
Signals up to SVGA can be displayed.
Cables connecting the personal computer vary according to the type of machine, so consult your product dealer.
11
RS-232C input terminal (RS-232C)
• Connects to the computer RS-232C output terminal.
12
Audio input terminals (AUDIO INPUT)
• Connects to the audio output terminal of a video deck
or similar device.
• For switching the RGB 1 terminals' 13-pin horizontal
sync and 14-pin vertical sync to terminate with 75 Ω.
When an analog synchronous signal is input at the
RGB 1 terminal, be sure that this switch is set to ANALOG (75 Ω). For connection to a personal computer,
be sure it is set to TTL.
14
RGB 2 input terminal (RGB 2 INPUT)
• Connects to the computer monitor's (analog RGB)
output terminal.
Signals from VGA to XGA can be displayed.
Cables connecting the personal computer vary according to the type of machine, so consult your product dealer.
• For switching the RGB 2 terminals' H terminal horizontal sync and V terminal vertical sync to terminate
with 75 Ω.
When an analog synchronous signal is input at the
RGB 2 terminal, be sure that this switch is set to ANALOG (75 Ω). For connection to a personal computer,
be sure it is set to TTL.
12
A Remote controller
ENGLISH
• POWER button
Switches the power on or off.
• MODE button
Selects the input mode.
• MENU button
For adjusting the picture and sound
to your taste
P15
P15
P20–39
• WIDE button
For selecting the desired wide
screen
• VOLUME buttons
For adjusting the volume
• SET button
For setting the menu items and adjustment items
• ADJUST button
For making adjustments from the
menu screen
P16–19
P15
P20–39
P20–39
• For the adjustment menu, see the pages below.
Handy functions (on-screen display, speaker, white balance, DPMS, language) ····························
VIDEO mode adjustment menu ·······································································································
• Do not subject the remote controller to strong mechanical shocks. Doing so can cause malfunction.
• D o not get the remote controller wet or leave it in a hot location or near any heat source such as a heater. Doing so can cause
malfunction or deformation.
• Do not wipe the remote controller with volatile liquids such as benzine or paint thinner.
P20–23
P24–31
P32–39
13
NAMES OF PARTS AND THEIR FUNCTIONS
Handling the remote controller
Loading the batteries
Press on the cover and slide
in the direction of the arrow.
1
Reception range of remote controller
Load two AA batteries, taking
care that the + and – ends face
2
the correct direction.
Close the cover until it clicks.
3
Upper
20°
20°
Lower
30° 30°
5m (Front)
Points about usage
• Use the remote controller pointed in the direction of the remote control reception section, making sure there is no obstruction.
• The remote controller may not operate correctly in a room using high-frequency fluorescent lights. If this happens, move away
from those lights.
• After it has been used for a long time, the remote controller batteries go flat. When this happens, replace them with new ones.
• When replacing the batteries, make sure they are the same type as the originals.
RightLeft
14
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.