Fujitsu P42-2, P42-1A, P50-2 User Manual

Contents

Introduction........................................................................................................................................... 1
Notational conventions ................................................................................................................. 2
Important notes..................................................................................................................................... 2
Safety notes.................................................................................................................................. 2
Cleaning ....................................................................................................................................... 4
Transport ...................................................................................................................................... 4
Power cable.................................................................................................................................. 4
CE marking................................................................................................................................... 4
Disposal and recycling ................................................................................................................. 5
Preparing for use .................................................................................................................................. 5
Unpacking and checking the delivery........................................................................................... 5
Preparing remove control ............................................................................................................. 6
Inserting batteries................................................................................................................. 6
Replacing batteries............................................................................................................... 6
Installing plasma TV ..................................................................................................................... 7
Connections on plasma TV ........................................................................................................10
Connecting plasma TV ............................................................................................................... 13
Switching plasma TV on/off........................................................................................................ 14
Switching plasma TV on/into standby mode .............................................................................. 14
Setting language of the OSD menu............................................................................................ 15
Carrying out programme search................................................................................................. 15
Adjusting programme settings....................................................................................................16
Arranging programmes....................................................................................................... 17
Changing programme properties........................................................................................ 17
Deleting program................................................................................................................19
Selecting signal source .............................................................................................................. 19
Changing programme................................................................................................................. 19
Operation............................................................................................................................................ 20
Operating elements on the device.............................................................................................. 20
Changing the device settings with the buttons of the control panel ........................................... 21
Remote control ........................................................................................................................... 22
Teletext............................................................................................................................... 23
Buttons for editing programme list...................................................................................... 23
PIP (Picture in Picture)....................................................................................................... 23
Changing device settings with remote control............................................................................ 24
Description of menus.................................................................................................................. 24
PICTURE menu - picture settings ...................................................................................... 25
SOUND menu - sound settings.......................................................................................... 26
SETUP menu - advanced settings ..................................................................................... 27
TIME menu - time settings ................................................................................................. 29
Display modes.................................................................................................................................... 31
TV menu - programme settings.......................................................................................... 30
Main display mode ..................................................................................................................... 31
PIP mode (Picture in Picture) ..................................................................................................... 32
A26361-K1040-Z120-1-M119, edition 3 English
Downloaded From TV-Manual.com Manuals
Contents
Technical data.....................................................................................................................................33
VESA-DDC-compatible VGA interface .......................................................................................35
Preset operating modes (PC) .....................................................................................................35
Power consumption ....................................................................................................................35
PC Analogue (D-SUB) ................................................................................................................36
PC Digital (DVI-D).......................................................................................................................36
SCART (Half/Full) .......................................................................................................................37
S-Video .......................................................................................................................................37
Colour and transmission system by country ...............................................................................38
Troubleshooting ..................................................................................................................................40
English A26361-K1040-Z120-1-M119, edition 3
Downloaded From TV-Manual.com Manuals

Introduction

Your new plasma TV MYRICA P42-1A / P42-2 / P50-2possesses a whole range of useful features and functions, e.g.:
TFT monitor (Thin Film Transistor; active matrix)
analogue tuner for VHF, UHF and cable programmes
connections for SCART (video and RGB), video and S-Video
minimal space requirements thanks to slim casing
optimum ergonomic characteristics (totally distortion-free and colour purity right into the
corners)
high degree of brightness and good contrast
high resolution for operation on a PC
easy-to-operate remote control
convenient operation via integrated OSD (On-Screen-display) menu
2 tuner picture in picture
picture size changeover: full-screen, panorama, zoom 1 and zoom 2
power management for reducing power consumption when the computer is not in use
integrated dual-channel loudspeakers
integrated NICAM/IGR sound decoder for stereo and two-channel sound
automatic switch-off function
Teletext
This operating manual contains important information you require to start up and run your device. For TV operation with the integrated tuner, a terrestrial antenna or a cable connection is required. As
an alternative, a satellite receiver can be connected to one of the SCART jacks. When you put the device into operation for the first time, you should carry out a programme search
(see "Preparing for use").
Target group
You don't need to be an "expert" to perform the operations described here. Do, however, read the "Important notes" chapter in the operating manual of the computer and in this operating manual.
In the event of any problems occurring, please contact your sales outlet or our help desk.
Additional information
Details of how you set the resolution and refresh rate are provided in the documentation on your screen controller/the associated driver software.
A26361-K1040-Z120-1-M119, edition 3 English - 1
Downloaded From TV-Manual.com Manuals
MYRICA P42-1A / P42-2 / P50-2

Notational conventions

The meanings of the symbols and fonts used in this manual are as follows:
Text which follows this symbol describes activities that must be performed in the order shown. "Quotation marks" indicate names of chapters or terms. Texts in italics indicate filenames and menu items.
Pay particular attention to text marked with this symbol. Failure to observe this warning endangers your life, destroys the device, or may lead to loss of data.
!
Supplementary information, remarks, and tips follow this symbol.
i

Important notes

In this chapter you will find information regarding safety which is essential to take note of with your plasma TV.
Avoid still images on the screen for longer periods, e.g. still images from videos, sender label etc. (maximum of 1 hour).
!
This pictures may remain visible! Also avoid longer operation in a picture mode in which black bars are visible. These black bars can also remain visible.
This product from Fujitsu Siemens Computers contains intellectual property of third parties. Any tampering with or modification of the product will void the warranty and may
!
lead to legal prosecution to the full extent of the law.

Safety notes

This device complies with the relevant safety regulations for data processing equipment, including electronic office machines for use in an office environment. If you have any questions, contact your sales outlet or our help desk.
The display surface of the plasma TV is sensitive to pressure and scratches. You should therefore be careful with the display surface so as to avoid lasting damage (Newton rings, scratches).
If the device is brought into the installation site from a cold environment, condensation can form. Before operating the device, wait until it is absolutely dry and has reached approximately the same temperature as the installation site.
During installation and before operating the device, please observe the instructions on environmental conditions in the "Technical data" chapter as well as the instructions in the "Preparing for use" chapter.
To ensure sufficient ventilation, the intake and exhaust air openings of the device must never be blocked.
2 - English A26361-K1040-Z120-1-M119, edition 3
Downloaded From TV-Manual.com Manuals
MYRICA P42-1A / P42-2 / P50-2
The device may not be placed on the floor.
he device automatically sets itself to the correct voltage within the range from 100 V to 240 V.
Ensure that the local mains voltage lies within these limits.
Ensure that the power socket on the device or the earthed mains outlet is freely accessible.
The ON/OFF switch does not disconnect the device from the mains voltage. To completely
disconnect the mains voltage, remove the power plug from the socket.
Lay all cables so that nobody can stand on them or trip over them. When attaching the device, observe the relevant notes in the "Preparing for use" chapter.
If you use a different PC data cable from the one supplied, ensure that it is adequately shielded. CE conformance and optimum picture quality are guaranteed only if you use the data cable supplied.
No antenna or data transfer cables should be connected or disconnected during a thunderstorm.
Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get inside the device (danger of electric shock, short circuit).
The device is not waterproof! Protect the device from spray water (rain, sea water).
In emergencies (e.g. damaged casing, elements or cables, penetration of liquids or foreign
matter), switch off the unit, disconnect the power plug and contact your sales outlet or our help desk.
The device must be disposed of in accordance with the local regulations for disposal of special waste. During handling and disposal, the safety regulations applicable to fluorescent materials must be observed.
Only qualified technicians should repair the device. Unauthorised opening and incorrect repair may greatly endanger the user (electric shock, fire risk).
You may set only those resolutions and refresh rates specified in the "Technical data" chapter. Otherwise you may damage your monitor. If you are in any doubt, contact your sales outlet or our help desk.
Use a screen saver with moving images in PC mode and activate the power management for your monitor to prevent still images from "burning in".
Keep this operating manual together with your device. If you pass on the device to third parties, you should include this manual.
A26361-K1040-Z120-1-M119, edition 3 English - 3
Downloaded From TV-Manual.com Manuals
MYRICA P42-1A / P42-2 / P50-2

Cleaning

Remove the power plug before cleaning the device.
Do not clean any interior parts yourself, leave this job to a service technician.
Do not use any cleaning agents that contain abrasives or may corrode plastic.
Ensure that no liquid will run into the system.
Ensure that the ventilation areas of the device are free.
The display surface of the device is sensitive to pressure and scratches. Clean it only using a
soft, slightly moistened cloth.
Wipe the device casing with a dry cloth. If the monitor is particularly dirty, use a cloth which has been moistened in mild domestic detergent and then carefully wrung out.

Transport

Transport the device with care and only in its original packaging or another corresponding packaging to protect it from knocks and jolts.
Never drop the device (danger of glass breakage).

Power cable

To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary to replace the original cable set.
The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.
The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the
outer sheath.
For devices which are mounted on a desk or table, type SVT or SJT cable sets may be used. For devices which sit on the floor, only SJT type cable sets may be used.
The cable set must be selected according to the rated current for your device.

CE marking

The shipped version of this device complies with the requirements of the EEC directives 89/336/EEC "Electromagnetic compatibility" and 73/23/EEC "Low voltage directive".
4 - English A26361-K1040-Z120-1-M119, edition 3
Downloaded From TV-Manual.com Manuals
MYRICA P42-1A / P42-2 / P50-2

Disposal and recycling

This device has been manufactured to the highest possible degree from materials which can be recycled or disposed of in a manner that is not environmentally damaging. The device may be taken back after use to be recycled, provided that it is returned in a condition that is the result of normal use. Any components not reclaimed will be disposed of in an environmentally acceptable manner.
If you have questions on disposal, please contact your point of sale, our Help Desk or obtain information at: www.fujitsu-siemens.com/recycling

Preparing for use

Unpacking and checking the delivery

The display surface of the device is sensitive to pressure and scratches. Always hold the device by the casing!
!
Unpack all the individual parts. Check the delivery for damage incurred during transportation. Check whether the delivery agrees with the details in the delivery note.
The complete device package includes: – one plasma TV
a foot with mounting screws – one power cable – one remote control – two batteries type AAA – one Warranty Booklet – one "Getting Started" manual (two volumes) – this Operating Manual (two volumes)
Should you discover that the delivery does not correspond to the delivery note, notify your local sales outlet immediately.
We recommend that you keep the original packaging material. Keep it for future transportation.
i
A26361-K1040-Z120-1-M119, edition 3 English - 5
Downloaded From TV-Manual.com Manuals
MYRICA P42-1A / P42-2 / P50-2

Preparing remove control

Inserting batteries
Open the back cover of the remote control by
sliding it in the direction of the arrow.
Place the batteries supplied in the battery
compartment. Ensure correct polarity.
Close the battery compartment by sliding the
cover back on until you hear and feel it click into place.
Remove the batteries when not using the remote control for longer periods.
i
Handle the remote control with care. Do not drop the remote control on the floor. Do not expose the remote control to moisture, direct sunlight or high temperatures.
Replacing batteries
When the batteries are used up (indicator no longer lights up), replace them with two batteries
of the same type (type AAA).
Do not throw batteries or accumulators into the household waste. Batteries or accumulators must be disposed of in accordance with local regulations concerning special
i
waste.
6 - English A26361-K1040-Z120-1-M119, edition 3
Downloaded From TV-Manual.com Manuals
MYRICA P42-1A / P42-2 / P50-2

Installing plasma TV

Before you install your plasma TV, you must mount the foot on the device.
Lay the plasma TV on a smooth, clean work surface with the front facing downward.
The foot is shown as an example in the following illustrations. The delivered foot may differ from the illustration.
i
Make sure that no objects are lying on the work surface, as otherwise the frame or display surface could be damaged.
!
Recesses for mounting the foot are provided on the left and right on the back of the device.
Turn the foot so that the two shafts
point toward the recesses and the wider section of the foot is facing downward.
Push the shafts of the foot as far as
possible into the recesses.
Two holes are provided on the left and right in the back panel of the device.
A26361-K1040-Z120-1-M119, edition 3 English - 7
Downloaded From TV-Manual.com Manuals
MYRICA P42-1A / P42-2 / P50-2
Screw on the shafts of the foot through
the holes on the device. Use the screws provided for this
purpose.
You can now place the plasma TV in the upright position.
The device may not be placed on the floor.
8 - English A26361-K1040-Z120-1-M119, edition 3
Downloaded From TV-Manual.com Manuals
MYRICA P42-1A / P42-2 / P50-2
Ventilation
To ensure sufficient ventilation, the intake and exhaust air openings of the device must never be blocked.
!
>10 cm >20 cm>20 cm
>10 cm
When installing the TV in niches, maintain the minimum distance for sufficient ventilation of the device: 10 cm from the side and back, 20 cm from the top.
>10 cm
>10 cm
A26361-K1040-Z120-1-M119, edition 3 English - 9
Downloaded From TV-Manual.com Manuals
MYRICA P42-1A / P42-2 / P50-2

Connections on plasma TV

Observe the safety precautions in the "Important notes" chapter in this operating manual.
!
Do not cover the ventilation openings of the monitor. Never open the housing of the power supply unit. There is extreme danger from an
electrical shock with the housing open. There are no components requiring cleaning or repairs in the interior.
5
12364
1 = RS-232 port 2 = DVI port 3 = AUDIO ports (LINE) 4 = PC-IN port (VGA) 5 = COMPONENT ports (2x) 6 = Loudspeaker ports 7 = SCART1 port (Half)
The following devices can be connected to this plasma TV:
RS-232 (black)
DVI IN (white)
5
Serial port For customer service, e.g. for updating the firmware
Connection for digital video input signals e.g. a PC with a digital output (DVI-D) or for HDTV devices
789
8 = SCART2 port (Full) 9 = S-VIDEO port 10 = AV ports (OUT) 11 = AV ports (IN) 12 = ON/OFF switch 13 = Antenna port 14 = Power connector
1210
11 13 14
AUDIO IN white (left) red (right)
10 - English A26361-K1040-Z120-1-M119, edition 3
Downloaded From TV-Manual.com Manuals
Connection for audio input signals (LINE IN) e.g. for a PC or for HDTV devices
MYRICA P42-1A / P42-2 / P50-2
PC IN (blue)
COMPONENT 1 COMPONENT 2
Y - green Pb - blue Pr - red
AUDIO white (left)
red (right)
SPEAKER red/right/+
black/right/-
black/left/-
red/left/+
SCART 1 (Half)
Connection for analogue VGA input signals e.g. for a PC with an analogue output (D-SUB)
Connections for component video and audio input signals e.g. for HDTV decoder, HDTV video recorder or HDTV player
Connection terminals for external loudspeakers
Connection for AV (CVBS) and audio input signals e.g. for satellite receiver, DVD player, video recorder,
decoders or a gaming console
SCART 2 (Full)
A26361-K1040-Z120-1-M119, edition 3 English - 11
Downloaded From TV-Manual.com Manuals
Connection for AV (CVBS, RGB) and audio input signals e.g. for satellite receiver, DVD player, video recorder,
camcorder or a gaming console
MYRICA P42-1A / P42-2 / P50-2
S-VIDEO IN Connection for S-VIDEO input signals
e.g. for DVD player, video recorder or film camera with S-
Video connection AV: VIDEO
yellow AUDIO
white (left) red (right)
TV-ANT. antenna cable port
AC INPUT Connector for the power cable
Connections for video and audio input signals
e.g. for DVD player, video recorder, film camera with S-Video
connection or gaming console
12 - English A26361-K1040-Z120-1-M119, edition 3
Downloaded From TV-Manual.com Manuals
Loading...
+ 30 hidden pages