Fujitsu MHV2160BT - 160GB SATA/150 4200RPM 8MB Notebook Hard, MHV2160BT Drive Installation Manual

CHAPTER 3 Installation Conditions

3.1 Dimensions

3.2 Mounting

3.3 Connections with Host System

This chapter gives the external dimensions, installation conditions, surface
temperature conditions, cable connections, and switch settings of the hard disk
drives.

C141-E244 3-1

Installation Conditions

3.1 Dimensions

Figure 3.1 illustrates the dimensions of the disk drive. All dimensions are in mm.

*1 The PCA and connectors are not included in these dimensions.
*2 Dimension from the center of the user tap to the base of the connector pins
*3 Length of the connector pins
*4 Dimension from the outer edge of the user tap to the center of the connector

pins

*5 Dimension from the outer edge of the user tap to the innermost edge of the

connector pins

Figure 3.1 Dimensions

3-2 C141-E244

3.2 Mounting

3.2 Mounting

For information on mounting, see the "FUJITSU 2.5-INCH HDD
INTEGRATION GUIDANCE (C141-E144)."

(1) Orientation

The disk drives can be mounted in any direction.

(2) Frame

The MR head bias of the HDD disk enclosure (DE) is zero. The mounting frame
is connected to Signal Ground (SG).

IMPORTANT

Use M3 screw for the mounting screw and the screw length should
satisfy the specification in Figure 3.2.

The tightening torque must be 0.49N • m (5kgf • cm).
When attaching the HDD to the system frame, do not allow the

system frame to touch parts (cover and base) other than parts to
which the HDD is attached.

(3) Limitation of mounting

Note) These dimensions are recommended values; if it is not possible to satisfy

them, contact us.

Bottom surface mounting

DE

2

A

Frame of system
cabinet

3.0 or less

Details of A

Screw

2.5

2.5

Frame of system
cabinet

3.0 or less

Side surface
mounting

PCA

Screw

2.5 2.5

B

C141-E244 3-3

Figure 3.2 Mounting frame structure

Installation Conditions

IMPORTANT

Because of breather hole mounted to the HDD, do not allow this to
close during mounting.

Locating of breather hole is shown as Figure 3.3.
For breather hole of Figure 3.3, at least, do not allow it around

φ 2.4

to block.

3-4 C141-E244

Figure 3.3 Location of breather

3.2 Mounting

(4) Ambient temperature

The temperature conditions for a disk drive mounted in a cabinet refer to the
ambient temperature at a point 3 cm from the disk drive. The ambient
temperature must satisfy the temperature conditions described in Section 1.4, and
the airflow must be considered to prevent the DE surface cover temperature from
exceeding 60

°C.

Provide air circulation in the cabinet such that the PCA side, in particular,
receives sufficient cooling. To check the cooling efficiency, measure the surface
cover temperatures of the DE. Regardless of the ambient temperature, this
surface cover temperature must meet the standards listed in Table 3.1. Figure 3.4
shows the temperature measurement point.

1

Figure 3.4 Surface cover temperature measurement points

Table 3.1 Surface temperature measurement points and standard values

No. Measurement point Temperature

1 DE cover 60 °C max

C141-E244 3-5

Installation Conditions

(5) Service area

Figure 3.5 shows how the drive must be accessed (service areas) during and after
installation.

Mounting
screw hole

Cable connection

Mounting screw hole

Figure 3.5 Service area

Data corruption: Avoid mounting the disk drive near strong

magnetic sources such as loud speakers. Ensure that the disk drive
is not affected by external magnetic fields.

Damage: Do not press the cover of the disk drive. Pressing it too
hard, the cover and the spindle motor contact, which may cause
damage to the disk drive.

Static: When handling the device, disconnect the body ground
(500 kΩ or greater). Do not touch the printed circuit board, but hold
it by the edges.

(6) Handling cautions

Please keep the following cautions, and handle the HDD under the safety
environment.

3-6 C141-E244

3.2 Mounting

p

ying

p

g

p

- General notes

ESD mat

Wrist strap

Use the Wrist stra

Do not hit HDD each other.

Do not
to avoid fallin

lace HDD vertically

.

down.

Shock absorbing mat

Place the shock absorbing mat on the
operation table, and place ESD mat on it.

Do not stack when carr

Do not dro

.

.

- Installation

(1) Please use the driver of a low impact when you use an electric driver.

HDD is occasionally damaged by the impact of the driver.

(2) Please observe the tightening torque of the screw strictly.

M3 ······· 0.49N • m (5 kgf • cm).

-

Recommended equipments

Contents Model Maker

Wrist strap JX-1200-3056-8 SUMITOMO 3M ESD

ESD mat SKY-8A (Color Seiden Mat) Achilles

Shock Low shock driver SS-6500 HIOS

C141-E244 3-7

Figure 3.6 Handling cautions

Installation Conditions

3.3 Connections with Host System

3.3.1 Device connector

The disk drive has the SATA interface connectors listed below for connecting
external devices. Figure 3.7 shows the locations of these connectors and
terminals.

SATA interface
and power
connectors

Figure 3.7 Connector locations

PCA

3-8 C141-E244

3.3 Connections with Host System

3.3.2 Signal segment and power supply segment

Figure 3.8 shows each segment of the SATA interface connector and pin
numbers.

View from the
connector side

Power supply

segment

P1 pins in the power

supply segment

Signal segment

S1 pins in the signal

segment

Figure 3.8 Power supply pins (CN1)

3.3.3 Connector specifications for host system

Table 3.2 lists the recommended specifications for the host interface connectors.

View from the
PCA side

Table 3.2 The recommended connector specifications for the host syst em

Segment Name Model (Manufacturer)

SATA interface
and power supply

C141-E244 3-9

Host receptacle 67492-0220 (Molex) or compatibles

Installation Conditions

3.3.4 SATA interface cable connection

The cable that connects the disk drive to the host system must be compliant with
the Serial ATA 1.0a specification.

3.3.5 Note about SATA interface cable connection

Take note of the following precaution about plugging a SATA interface cable into
the SATA interface connector of the disk drive and plugging the connector into a
host receptacle:

When plugging together the disk drive SATA interface connector
and the host receptacle or SATA interface cable connector, do not
apply more than 10 kgf of force in the connection direction once
they are snugly and securely in position.

3-10 C141-E244