Page 1
LR 6632
HARDWARE GUIDE
TV Tuner Card
Hardware Specifications
Hardware Installation
Connecting Input & Output Devices
Driver Installation
Contents
Page 2
Hardware Interface
Compatibility
TV Tuner
FM Tuner (Optional)
!
!
!
!
!
!
!
!
!
!
!
!
32-bit PCI 2.2 bus mastering
Plug-n-Play compliant
Video Standards
Connectors
Graphics drivers must include DirectX 8.1 or later
software
PAL/SECAM
PAL/SECAM
Full 181 channels supported
Stereo FM 87.5MHz - 108MHz
1 FM RF connector
1 TV RF connector
2 Audio jacks
1 Mini DIN 4-pin connector for S-Video
1 RCA jack for Composite Video
Hardware Specifications
Page 3
Hardware Installation
Step 1:
Step 2:
Step 3:
TV Tuner card
Step 5:
Power off your PC. Open the computer case. Remove the coverplate
of an unused expansion slot.
Align the bus on the card with the PCI slot.
Gently press down into the slot until you feel the edge
of the bus reaches the bottom of the PCI slot. Note that the capture
card can be inserted into PCI slot in one direction only.
Connect the input sources and output devices to your capture card
following the instructions given in
section on the next page. Now you are ready to connect the
video sources to your capture card.
Step 4:
Secure the bracket of the card to your computer case with the screws.
Then fit the computer case cover back in place.
Connect Input and Output
Devices
Page 4
FM Antenna
From Cable TV
or Antenna
VCR
Input sources
S-Video out
S-Video in
Audio out
Audio in
DVD/VCD Player
CCD cameraCCD camera Camcorder
SELECT START
ANALOG
SONY
PlayStation
Video Game Console
Composite
Video out
Composite
Video in
5
6
4
3
2
1
5
6
4
3
2
1
FM
TV in
Audio in (L)
Audio in (R)
S-Video in
Composite Video in
Connectors
Connect Input & Output Devices
Page 5
Driver Installation
Step 1:
Turn on your PC and start up the
Windows.
Step 2
Found New
Hardware Wizard
Install from a list
or specific location Next.
:
Shortly after entering the Windows ,
you will see the
dialog box as
shown in the first figure to the right.
Tick the option for '
'. Then click
Step 4:
The wizard will then start searching
for the driver at the given location.
Step 5:
When the driver is located, Windows
will then start installing the first
driver. A dialog box with a progress
bar appears.
Step 3
Include this
location in the search
G:\
Next
:
The wizard will next prompt you to
choose your search and installation
options as shown in the second figure
to the right. Tick '
' then give the
location: (assuming G is your
CD-ROM drive location), or browse
for it. If you downloaded the driver
from our web site, please type in the
directory where you saved the driver
file. Then click .
Installing the First Driver
Page 6
Step 6:
When the installation of the first driver
is completed. A dialog box appears as
shown in the figure to the right. Click
Finish.
Step 7
Found New Hardware Wizard
Install from a list or specific location
Next
:
After finishing installing the first driver,
the
dialog box restarts. Tick the option for
''.
Then click .
Installing the Second Driver
Step 8
Include this location in
the search
G:\
Next
:
Like the first time, the wizard
prompts you to choose your
search and installation options.
Tick '
' then give the
location: (assuming G is
your CD-ROM drive location),
or browse for it. And then click
.
Step 9:
The wizard will then start searching for
the driver at the given location.
Step 10:
When the driver is
located, the Windows
will start installing the
second driver. A dialog
box with a progress bar
will appear.
Page 7
Installing the Third Driver
Step 11:
Finish
When the installation is finished. The
wizard will display a dialog box to tell
you so. Click .
Step 12
Found New Hardware
Wizard
Install from a list or
specific location Next.
:
Again, the
dialog box restarts. Tick the
option for '
'. Then click
Step 13
Include this location in
the search
G:\
Next
:
Like the last time, the wizard
prompts you to choose your
search and installation options.
Tick '
' then give the
location: (assuming G is
your CD-ROM drive location),
or browse for it. And then click
.
Step 14:
The wizard will then start searching for
the driver at the given location.
Step 15:
When the driver is
located, the Windows
will start installing the
third driver. A dialog
box with a progress
bar will appear.
Page 8
Installing the Fourth Driver
Step 16:
Finish
When the installation is done. The
wizard will display a dialog box to tell
you so. Click .
Step 17
Found New Hardware
Wizard
Install from a list or
specific location Next
:
Again, the
dialog box restarts. Tick the
option for '
'. Then click .
Step 18
Include this location in the
search
G:\
Next
:
Again, the wizard prompts you
to choose your search and
installation options. Tick
'
' then give the location:
(assuming G is your CDÂROM drive location), or
browse for it. And then click
.
Step 19:
The wizard will then start searching for
the driver at the given location.
Step 20:
Finish
When the driver is located, the
windows will start installing
the fourth driver. When the
installation is finished. The
wizard will display a dialog
box to tell you so. Click .
Loading...