Fujitsu LifeBook T900 BIOS Guide

Fujitsu LifeBook

FUJITSU AMERICA, INCORPORATED

T Series

BIOS Guide

LifeBook T Series Models:

T900

Document Date: 02/03/2010

Document Part Number: FPC58-2643-01

1

LifeBook T Series BIOS

[ ], [ ]

[ ], [ ].

T Series BIOS

BIOS SETUP UTILITY

The BIOS Setup Utility is a program that sets up the
operating environment for your notebook. Your BIOS
is set at the factory for normal operating conditions,
therefore there is no need to set or change the BIOS
environment to operate your notebook.

The BIOS Setup Utility configures:

■

Device control feature parameters, such as changing
I/O addresses and boot devices.

■

System Data Security feature parameters, such as
passwords.

Entering the BIOS Setup Utility

To enter the BIOS Setup Utility, do the following (or use
the SecureCore Menu, as detailed in the next section):

1. Turn on or restart your notebook.

2. Press [F2] once the Fujitsu logo appears on the
screen. This will open the main menu of the BIOS
Setup Utility with the current settings displayed.

3. Press the [RIGHT ARROW] or [LEFT ARROW] key
to scroll through the other setup menus to review or
alter the current settings.

Using the SecureCore Menu

When the Fujitsu logo appears on the screen. press the
[Enter] key or click on the left mouse or touchpad
button; the SecureCore Menu will appear.

The SecureCore Menu provides shortcuts to the
following menus and information screens:

■

BIOS Setup

■

Diagnostic Screen

■

Boot Menu

■

Patent Information

■

System Information

■

Continue Booting

Clicking on any of the fields will invoke the screen,
information, or action described.

The Boot Menu can also be invoked by pressing the

[F12] key when the Fujitsu logo appears on the
screen.

Navigating through the Setup Utility

The BIOS setup utility consists of six menus: Info,
System, Advanced, Security, Boot, and Exit. This docu­ment explains each menu in turn, including all
submenus and setup items.

The following procedures allow you to navigate the
setup utility menus:

1. To select a menu, use the cursor keys:

2. To select a field within a menu or a submenu, use the

cursor keys:

3. To select the different values for each field, press the
[Spacebar] or [+] to change to the next lower
selection and [F5] or [-] to go to the next higher
selection.

4. To activate a submenu press the [Enter] key.

5. To return to a menu from a submenu, press the [Esc]
key.

6. To go to the Exit menu from any other menu,
press the [Esc] key.

■

Selecting a field causes a help message
about that field to be displayed on the
right-hand side of the screen.

■

Pressing the Enter key with the highlight
on a selection that is not a submenu or
auto selection will cause a list of all
options for that item to be displayed.
Pressing the Enter key again will select
the highlighted choice.

7. Pressing the [F9] key resets all items in the BIOS to
the default values.

8. Pressing the [F10] key saves the current configura­tion and exits the BIOS Setup Utility. You will be
asked to verify this selection before it is executed.

9. Pressing the [F1] key gives you a general help screen.

Entering the Setup Utility After a Configuration Change or System Failure

If there has been a change in the system configuration
that does not agree with the parameter settings stored in
your BIOS memory, or there is a failure in the system,
the system beeps and/or displays an error message after
the Power On Self Test (POST). If the failure is not too

2

severe, it will give you an opportunity to modify the
setup utility settings, as described in the following steps:

1. When you turn on or restart the computer there is a
beep and/or the following message appears on the
screen:

Error message - please run SETUP
program Press <F1> key to continue,
<F2> to run SETUP

2. If an error message is displayed on the screen, and
you want to continue with the boot process and start

the operating system anyway, press the [F1] key.

■

If your notebook emits a series of beeps
that sounds like a code and the display is
blank, please refer to the Troubleshoot­ing Section in the system User’s Guide.
The Troubleshooting Section includes a
list of error messages and their meanings.

■

If your data security settings require it,
you may be asked for a password before
the operating system will be opened.

3. If an error message is displayed on the screen, and
you want to enter the setup utility, press the [F2] key.

4. When the setup utility starts with a fault present, the
system displays the following message:

Warning!

Error message

[Continue]

5. Press any key to enter the setup utility. The system
will then display the Info Menu with current param­eters values.

Info Menu

3

LifeBook T Series BIOS

INFO MENU - DISPLAYS BASIC SYSTEM INFORMATION

The Info Menu is a display only screen that provides the
configuration information for your notebook.

The following table shows the names of the menu fields
for the Info menu and the information displayed in

Phoenix SecureCore(tm) Setup Utility

Info System Advanced Security Boot Exit

Product Name: T900

Serial Number: XXXXXXXX
BIOS Version: X.0X (XX/XX/2010)

Processor Type: Intel(R) Core(TM) i5 CPU M 540 @ 2.53GHz

Total Memory: 2048 MB
Memory Slot 1: 1024 MB DDR3 SDRAM
Memory Slot 2: 1024 MB DDR3 SDRAM

those fields. These fields are for information purposes
only, and cannot be modified by the user.

The information, including CPU type and
speed, and total memory, displayed on this
screen varies according to the unit you
purchased.

Onboard MAC Address: XX-XX-XX-XX-XX-XX
UUID: XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX

F1 Help
ESC Exit

Select Item
Select Menu

-/Space Change Values
Enter Select Sub-Menu

Figure 1. Info Menu

▲

F9 Setup Defaults
F10 Save and Exit

Table 1: Fields, Options and Defaults for the Info Menu

Menu Field Default Menu Field Default

Note that all of the fields on this screen are display only and are for reference.
Note that the parameters listed may be different for your system, depending upon the system configuration.

Product Name: T900 Memory Slot 1: 1024 MB DDR3 SDRAM

Serial Number: XXXXXXXX Memory Slot 1: 1024 MB DDR3 SDRAM

BIOS Version: 1.0 (XX/XX/2010) Onboard MAC Address: XX-XX-XX-XX-XX-XX

Processor Type: Intel(R) Core(TM) i5 CPU M 540 @

Total Memory: 2048 MB

2.53GHz

UUID: XXXXXXXX-XXXX-XXXX-XXXX-

XXXXXXXXXXXX

4

Phoenix SecureCore(tm) Setup Utility

F1 Help
ESC Exit

Select Item
Select Menu

-/Space Change Values
Enter Select Sub-Menu

F9 Setup Defaults
F10 Save and Exit

▲

Info System Advanced Security Boot Exit

Item Specific Help

Adjust calendar clock.

<Tab>, <Shift-Tab>, or
<Enter> selects field.

▲▲

System Time: [14:57:01]

System Date: [02/02/2010]

Drive0 [FUJITSU MHY2080BH]
Drive1 [MATSHITADVD-RAM UJ870BJ]

Language: [English (US)]

System Menu

SYSTEM MENU – SETTING STANDARD SYSTEM PARAMETERS

The System Menu allows you to set or view the current
system parameters. (See Navigating through the Setup

Utility on page 2 for more information.)

The following tables show the names of the menu fields
for the System menu and its submenus, all of the options
for each field, the default settings and a description of

the field’s function and any special information needed
to help understand the field’s use.

System Time and System Date can also be
set from your operating system without
using the setup utility. Use the Date and
Time icon on your Windows Control panel
or type time or date from the MS-DOS
prompt.

Table 2: Fields, Options and Defaults for the System Menu

Note that the parameters listed in the following table may vary depending upon your system’s configuration.

Menu Field Options Default Description

System Time: –— –— Sets and displays the current time. Time is in a 24 hour format

System Date: –— –— Sets and displays the current date. Date is in a month/day/year

Figure 2. System Menu

of hours:minutes:seconds with 2 digits for each. (HH:MM:SS).
Example: 16:45:57. You may change each segment of the time
separately. Move between the segments with the [Tab] key and/or
[Shift] + [Tab] keys.

numeric format with 2 digits each for month and day and 4 digits for
year. (MM/DD/YYYY) for example: 03/20/2007. You may
change each segment of the date separately. Move between the
segments with the [Tab] key and/or [Shift] + [Tab] keys.

5

LifeBook T Series BIOS

Table 2: Fields, Options and Defaults for the System Menu

Note that the parameters listed in the following table may vary depending upon your system’s configuration.

Menu Field Options Default Description

Drive0 Selects the Drive0

Drive1: Selects the Drive1

Language:

Serial ATA drive
submenu

Serial ATA drive
submenu

■

English (US)

■

Japanese (JP)

The product
number of the hard
drive.

The product
number of the
optical drive.

[English (US)] The default setting differs between the US/European and the

Display the type of device on this ATA/IDE interface. Pressing the
Enter key selects the Serial ATA Drive0 submenu allowing additional
device configuration options for this interface.

Display the type of device on this ATA/IDE interface, if there is one.
Pressing the Enter key selects the Serial ATA Drive1 submenu allow­ing additional device configuration options for this interface.

Japanese model. Selects the display language for the BIOS.

6

Drive0 Submenu of the System Menu

Phoenix SecureCore(tm) Setup Utility

F1 Help
ESC Exit

Select Item
Select Menu

-/Space
Enter

F9 Setup Defaults
F10 Save and Exit

Change Values
Select Sub-Menu

Item Specific Help

[Disabled]
The drive is disabled.

[Enabled]
The drive is enabled.

Drive0 [FUJITSU MHY2080BH]

Drive0: [Enabled]

Type: Hard Disk
Model: FUJITSU MHY2080BH
Capacity: 80GB
(80,026,361,856 Bytes)

▲

Info System Advanced Security Boot Exit

The Drive0 submenu identifies what ATA devices are installed.

System Menu

Figure 3. Drive0 Master Submenu

Table 3: Fields, Options and Defaults for the Drive0 Submenu of the System Menu

Menu Field Options Default Description

Drive0:

Typ e: ---

Model:

Capacity

■

■

---

---

Disabled
Enabled

[Enabled] Allows you to enable or disable the hard drive 0.

--- Information only: Displays the type of hard disk installed as drive 0.

--- Information only: Displays the model of hard disk installed as drive 0.

--- Information only: Displays the capacity of hard disk installed as drive 0.

7

LifeBook T Series BIOS

F1 Help
ESC Exit

Select Item
Select Menu

-/Space
Enter

F9 Setup Defaults
F10 Save and Exit

Change Values
Select Sub-Menu

Item Specific Help

[Disabled]
The drive is disabled.

[Enabled]
The drive is enabled.

Drive1 [MATSHITADVD-RAM UJ870BJ]

▲

Phoenix SecureCore(tm) Setup Utility

Info System Advanced Security Boot Exit

Drive1: [Enabled]

Type: CD/DVD
Model: MATSHITADVD-RAM UJ870BJ

Drive1 Submenu of the System Menu

The Drive1 submenu allows you to configure secondary ATA devices.

Figure 4. Drive1 Submenu

Table 4: Fields, Options and Defaults for the Drive1 Submenu of the System Menu

Menu Field Options Default Description

Drive1:

Type: ---

Model:

Exiting from System Menu

When you have finished setting the parameters on this menu, you can either exit from the setup utility, or move to

■

Disabled

■

Enabled

---

[Enabled] Allows you to enable or disable the drive 1.

--- Information only: Displays the type of device installed as drive 1.

--- Information only: Displays the model of device installed as drive 1.

another menu. If you wish to exit from the setup utility, press the [Esc] key or use the cursor keys to go to the Exit
menu. If you wish to move to another menu, use the cursor keys.

8

F1 Help
ESC Exit

Select Item
Select Menu

-/Space
Enter

F9 Setup Defaults
F10 Save and Exit

Change Values
Select Sub-Menu

▲

Item Specific Help

▲ ▲ ▲ ▲ ▲

Keyboard/Mouse Features
Video Features
Internal Device Configurations
CPU Features
USB Features
Miscellaneous Configurations
Intel(R) Management Engine Configurations

Event Logging

Configures keyboard/
mouse features.

▲

Info System Advanced Security Boot Exit

Phoenix SecureCore(tm) Setup Utility

▲

Advanced Menu

ADVANCED MENU – SETTING DEVICE FEATURE CONTROLS

The Advanced Menu allows you to:

■

Set the keyboard and mouse features.

■

Select between the display panel and an external
display.

■

Enable or disable the ATA, Bluetooth, LAN, WLAN,
IEEE1394, and Internal Camera controllers.

■

Configure CPU and USB features in your system.

■

Configure a variety of power-saving features.

(See Navigating through the Setup Utility on page 2 for
more information.)

The following tables show the names of the menu fields
for the Advanced Menu and its submenus, all of the
options for each field, the default settings and a descrip­tion of the field’s function and any special information
needed to help understand the field’s use.

Figure 5. Advanced Menu

Table 5: Fields, Options and Defaults for the Advanced Menu

Menu Field Description

Keyboard/Mouse Features When selected, opens the Keyboard/Mouse Features submenu, which allows setting NumLock

Video Features When selected, opens the Video Features submenu, which allows routing of video signals to

Internal Device Configurations When selected, opens the Internal Device Configuration submenu, which allows enabling or dis-

CPU Features When selected, opens the CPU Features submenu to allow you to enable/disable multi-core pro-

parameters.

different displays.

abling the ATA, Bluetooth, LAN, WLAN, IEEE1394, and camera controllers.

cessing, SpeedStep(R) Technology, XD Bit functional;ity, and Virtualization Technology..

9

LifeBook T Series BIOS

Table 5: Fields, Options and Defaults for the Advanced Menu

Menu Field Description

USB Features When selected, opens the USB Features submenu to allow you to enable or disable legacy USB

Miscellaneous Configurations When selected, opens the Miscellaneous Configurations submenu to allow you to enable or disable

Intel(R) Management
Engine Configurations

Event Logging When selected, opens the event logging submenu.

devices and SCSI SubClass support.

the power button, Wake Up On LAN, Auro Save, and control volume settings.

When selected, opens the Intel Management Engine Configurations submenu to allow you to set
features of the Management Engine BIOS Extensions, and AMT (Active Management Technology)
CIRA (Client-Initiated Remote Access) requests.

10

F1 Help
ESC Exit

Select Item
Select Menu

-/Space
Enter

F9 Setup Defaults
F10 Save and Exit

Change Values
Select Sub-Menu

▲

Item Specific Help

[On] or [Off]
Numlock is On or Off.

[On/Padlock Off]
Numlock is On, but use
with [Fn] for 10-key
input.

* Windows XP or later
OS preserves Numlock
state when the user
logs off.

Keyboard/Mouse Features

Numlock: [Off]

Phoenix SecureCore(tm) Setup Utility

Info System Advanced Security Boot Exit

Advanced Menu

Keyboard/Mouse Features Submenu of the Advanced Menu

The Keyboard/Mouse Features submenu is for setting the parameters of the integrated and external mouse and
keyboard.

Figure 6. Keyboard/Mouse Features Submenu

Table 6: Fields, Options and Defaults for the Keyboard/Mouse Submenu of the Advanced Menu

Menu Field Options Default Description

Numlock:

■

On

■

Off

■

On/Padlock Off

[Off] Sets the NumLock function state when the computer completes booting.

When [On] or [Off], Numlock is on or off. When [On/Padlock Off] is selected,
Numlock is on, but [Fn] key must be used for 10-key input.

Windows XP (or later OS) preserves Numlock state when the user logs off.

11

LifeBook T Series BIOS

Video Features Submenu of the Advanced Menu

The Video Features submenu is for setting the display parameters.

Phoenix SecureCore(tm) Setup Utility

Info System Advanced Security Boot Exit

Video Features

Display: [Auto]

Item Specific Help

Select display terminal.

* This setting is not
effective after
operating system
starts up.

F1 Help
ESC Exit

Select Item
Select Menu

Figure 7. Video Features Submenu

-/Space
Enter

Change Values

▲

Select Sub-Menu

F9 Setup Defaults
F10 Save and Exit

Table 7: Fields, Options and Defaults for the Video Features Submenu of the Advanced Menu

Menu Field Options Default Description

Display:

■

Internal Flat Panel

■

External (Analog)

■

External [DVI]

■

Auto

[Auto] Selects where the video signal will be routed. Note that this setting is

overridden after Windows starts up.

12

Advanced Menu

Internal Device Configurations Submenu of the Advanced Menu

The Internal Device Configuration submenu allows the user to enable or disable Bluetooth, LAN, Wireless LAN, IEEE
1394 and internal camera controllers.

Phoenix SecureCore(tm) Setup Utility

Info System Advanced Security Boot Exit

Internal Device Configurations

Serial ATA Controller: [Enabled]
AHCI Configuration: [Enabled]
Bluetooth(R): [Enabled]
LAN Controller: [Enabled]
Wireless LAN: [Enabled]
IEEE1394 Controller: [Enabled]
WWAN Device: [Enabled]

Item Specific Help

[Disabled]
Serial ATA port is
disabled.

[Enabled]
Serial ATA port is
enabled.

Ambient Light Sensor: [Enabled]

F1 Help
ESC Exit

Select Item
Select Menu

-/Space
Enter

Change Values

▲

Select Sub-Menu

F9 Setup Defaults
F10 Save and Exit

Figure 8. Internal Device Configuration Submenu

Table 8: Fields, Options and Defaults for the Internal Device Configuration Submenu of the Advanced Menu

Menu Field Options Default Description

Serial ATA Controller:

AHCI Configuration:

Bluetooth:

LAN Controller:

Wireless LAN:

IEEE1394 Controller:

WWAN Device:

Ambient Light Sensor:

■

Disabled

■

Enabled

■

Disabled

■

Enabled

■

Disabled

■

Enabled

■

Disabled

■

Enabled

■

Disabled

■

Enabled

■

Disabled

■

Enabled

■

Disabled

■

Enabled

■

Disabled

■

Enabled

[Enabled] Enables or disables the Serial ATA port.

[Enabled] Enables or disables the selected Advanced Host Controller Interface

(AHCI).

[Enabled] Enables or disables the Bluetooth device.

[Enabled] Enables or disables the LAN controller.

[Enabled] Enables or disables the Wireless LAN controller.

[Enabled] Enables or disables the IEEE 1394 controller.

[Enabled] Enables or disables the Wireless WAN device.

[Enabled] Enables or disables the Ambient Light Sensor feature. Note that this

feature is available only in Windows 7 systems.

13

LifeBook T Series BIOS

F1 Help
ESC Exit

Select Item
Select Menu

-/Space
Enter

F9 Setup Defaults
F10 Save and Exit

Change Values
Select Sub-Menu

▲

Item Specific Help

Select enabling or
disabling for
multiple core in a
physical processor
package.

CPU Features

Multi-core:
HT Technology: [Enabled]
SpeedStep(R) Technology: [Enabled]

Virtualization Technology: [Disabled]
Intel(R) VT-d: [Disabled]
Intel(R) TXT: [Disabled]

[Enabled]

Phoenix SecureCore(tm) Setup Utility

Info System Advanced Security Boot Exit

CPU Features Submenu of the Advanced Menu

The CPU Features submenu provides options for configuring the Intel Core Multi-Processing and SpeedStep power
management features of the CPU.

Figure 9. CPU Features Submenu

Table 9: Fields, Options and Defaults for the CPU Features Submenu of the Advanced Menu

Menu Field Options Default Description

Multi-core:

HT Technology:

SpeedStep(R)
Technology:

Virtualization
Technology:

Intel(R) VT-d:

Intel(R) TXT:

14

■

Enabled

■

Disabled

■

Enabled

■

Disabled

■

Disabled

■

Enabled

■

Disabled

■

Enabled

■

Disabled

■

Enabled

■

Disabled

■

Enabled

[Enabled] Enables or disables the Intel Core Multi-Processing features.

[Enabled] Enables or disables the Hyper-Threading features.

[Enabled] Enables or disables the SpeedStep(R) Technology features.

[Disabled] Enables or disables Virtualization Technology, an Intel technology which

[Disabled] Enables or disables Virtualization Technology for Directed I/O (VT-d), a

[Disabled] Enables or disables Trusted Execution Technology, a trusted computer

includes hardware enhancements to improve upon software-based virtual­ization technologies.

virtualization-friendly memory management tool.

technology.

F1 Help
ESC Exit

Select Item
Select Menu

-/Space
Enter

F9 Setup Defaults
F10 Save and Exit

Change Values
Select Sub-Menu

▲

Item Specific Help

[Disabled]
The feature is disabled.

[Enabled]
Legacy USB Emulation
is enabled and USB
devices are available
without USB aware OS.

Legacy USB Support
SCSI SubClass Support: [Enabled]

[Enabled]

USB Features

Info System Advanced Security Boot Exit

Phoenix SecureCore(tm) Setup Utility

Advanced Menu

USB Features Submenu of the Advanced Menu

The USB Features submenu provides options for enabling or disabling the USB devices.

Figure 10. USB Features Submenu

Table 10: Fields, Options and Defaults for the USB Features Submenu of the Advanced Menu

Menu Field Options Default Description

Legacy USB Support:

SCSI SubClass Support:

■

Disabled

■

Enabled

[Enabled] When Enabled is selected, Legacy USB Emulation is enabled

■

■

Disabled
Enabled

[Enabled] When Enabled is selected, USB devices that belong to the

and the USB devices are available without a USB-aware OS.
When Disabled is selected, Legacy USB support is disabled.

SCSI subclass in the mass storage class (e.g., USB Memory
Key) are enabled. Note that enabling this feature may cause
the system to hang during POST, depending on the device
that is connected.

15

LifeBook T Series BIOS

F1 Help
ESC Exit

Select Item
Select Menu

-/Space
Enter

F9 Setup Defaults
F10 Save and Exit

Change Values
Select Sub-Menu

▲

Item Specific Help

Configures the power
button.

*ACPI OS ignores this
setting.

Miscellaneous Configurations

Power Button:
Wake up on LAN:
On Battery: [Enabled]
Force LAN Boot:
Resume on LAN:
Auto Save To Disk:
Volume Setting:
Hardware Power Management:

[Disabled]

[Disabled]

[Disabled]
[Always Enabled]
[On]
[Middle]
[Enabled]

Phoenix SecureCore(tm) Setup Utility

Info System Advanced Security Boot Exit

Miscellaneous Configurations Submenu of the Advanced Menu

The Miscellaneous Configurations submenu provides options for enabling or disabling the power button and the
Wake Up On LAN feature, and setting the volume and video memory size.

Figure 11. Miscellaneous Configurations Submenu

Table 11: Fields, Options and Defaults for the Miscellaneous Configurations Submenu of Advanced Menu

Menu Field Options Default Description

Power Button:

Wake up on LAN:

On Battery:

Force LAN Boot:

Resume on LAN:

Auto Save To Disk:

Volume Setting:

Hardware Power
Management:

16

■

Disabled

■

Power Off

■

Disabled

■

Enabled

■

Disabled

■

Enabled

■

Disabled

■

Enabled

■

On AC mode only

■

Always Enabled

■

Off

■

On

■

Off

■

Minimum

■

Middle

■

Maximum

■

Disabled

■

Enabled

[Disabled] Selecting Disabled disables the power button. Selecting Power Off

[Disabled] Enabled allows the system to wake up when the internal LAN device

[Enabled] When disabled, Wake Up On LAN is only enabled when there is an

[Disabled] This feature is active only when “Wake up on LAN” is enabled. When

[Always
Enabled]

[On] Turns the Auto Save To Disk feature on and off. When it it enabled,

[Middle] Selects the initial volume setting for the system.

[Enabled] Allows you to enable or disable the Hardware Power Management

allows you to turn off system power with the power button.

receives a specific signal while in power-off state. Selecting Disabled
disables this feature.

AC adapter connected.

enabled, in the event of a system wake-up on LAN, the system will try
to first boot from the LAN before attempting to boot from any other
device, regardless of the BIOS boot priority settings or disabling of the
Preboot Execution Environment.

When “On AC mode only” is selected, Wake Up On LAN from
standby/hibernate states is only enabled when AC adapter connected.

when a battery in Suspend mode reaches low battery state, its state
will be saved to disk and the system will power off.

technology.

Advanced Menu

Intel(R) Management Engine Configurations Submenu of the Advanced Menu

The Management Engine Configurations submenu allow you to set features of the Management Engine BIOS Exten­sions and AMT (Active Management Technology) CIRA (Client-Initiated Remote Access) requests.

Phoenix SecureCore(tm) Setup Utility

Info System Advanced Security Boot Exit

Intel(R) Management Engine Configurations

Intel(R) ME Setup Menu: [Enabled]
Intel(R) AMT CIRA Request Trigger: [Enter]
UnConfigure Intel(R) ME: [Enter]

Item Specific Help

[Disabled]
Intel(R) Management
Engine BIOS Extensions
screens are not
displayed.

[Enabled]
Intel(R) Management
Engine BIOS Extensions
screens are displayed.

F1 Help
ESC Exit

Select Item
Select Menu

Figure 12. Management Engine Configurations Submenu

-/Space
Enter

Change Values

▲

Select Sub-Menu

F9 Setup Defaults
F10 Save and Exit

Table 12: Fields, Options and Defaults for the Management Engine Configurations Submenu of the
Advanced Menu

Menu Field Options Default Description

Intel(R) ME Setup Menu:

Intel(R) AMT CIRA Request
Trigger:

UnConfigure Intel(R) ME: --- [Enter] Press [Enter] to proceed with un-configuring the Management

■

Disabled

■

Enabled

--- [Enter] Press [Enter] to make a request for help and seeking remote assis-

[Enabled] Enables or disables the Intel Management Engine BIOS Extensions

screens.

tance to help fix problems with your system.

Engine.

17

LifeBook T Series BIOS

F1 Help
ESC Exit

Select Item
Select Menu

-/Space
Enter

F9 Setup Defaults
F10 Save and Exit

Change Values
Select Sub-Menu

▲

Item Specific Help

Press <Enter> key to
view the contents of
the event log.

Event Logging

Event Log Capacity: Space Available
Event Log Validity: Valid

View Event Log: [Enter]

Event Logging: [Enabled]
System Boot Event: [Disabled]

Clear All Event Logs: [No]

Mark Events as Read: [Enter]

Info System Advanced Security Boot Exit

Phoenix SecureCore(tm) Setup Utility

Event Logging Submenu of the Advanced Menu

The Event Logging submenu configures event logging features for DMI events.

Figure 13. Event Logging Submenu

Table 13: Fields, Options and Defaults for the Event Logging Submenu of the Advanced Menu

Menu Field Options Default Description

Event Log Capacity: Space Available Display only

Event Log Validity: Valid Display only

View Event Log:

Event Logging:

System Boot Event:

Clear All Event Logs:

Mark Events as Read:

18

■

Enter [Enter] Allows you to view content of event log

■

Disabled

■

Enabled

■

Disabled

■

Enabled

■

No

■

Yes

■

Enter [Enter] Lets you mark all events currently in the event log as having been read.

[Enabled] Turns event logging on and off for all DMI events.

[Disabled] Turns event logging on and off for DMI system boot events.

[No] When set to [Yes] all event logs will be cleared at next boot.

F1 Help
ESC Exit

Select Item
Select Menu

-/Space
Enter

F9 Setup Defaults
F10 Save and Exit

Change Values
Select Sub-Menu

▲

Item Specific Help

Press <Enter> key to
set Supervisor Password
to enable any password
features.

Then password entry is
required to enter BIOS
Setup.

Supervisor Password Is: Clear
User Password Is: Clear

Set Supervisor Password [Enter]
Set User Password [Enter]
Minimum User Password Length: [0]
Password on Boot: [Disabled]
On Automatic Wake up: [Disabled]
Boot from Removable Media: [All]
Flash Write: [Enabled]
Hard Disk Security
Owner Information
TPM (Security Chip) Setting

▲ ▲

▲

Phoenix SecureCore(tm) Setup Utility

Info System Advanced Security Boot Exit

Security Menu

SECURITY MENU – SETTING THE SECURITY FEATURES

The Security menu allows you to set up the data security features of your notebook to fit your operating needs and to
view the current data security configuration. (See Navigating through the Setup Utility on page 2 for more information.)

The following tables show the names of the menu fields for the Security Menu and its submenus, all the options for
each field, the default settings and a description of the field's function and any special information needed to help
understand the field's use. The default condition is no passwords required and no write protection.

■

Remember your passwords! If you set and forget your User and Master hard disk passwords, Fujitsu
Computer Systems will not be able to reset it. You may lose data and have to replace your system
board or hard disk drive.

■

WARNING. VERY IMPORTANT if your hard disk drive is protected using a Full Disk Encryption (FDE)
"engine". FDE encrypts all data as it is written to the hard drive. When data is retrieved from the
hard drive, it is decrypted by the same engine. If you forget your hard disk security password on a

system with FDE, all data and applications on the hard drive will remain encrypted and will effec­tively be lost. Be sure to remember your hard disk password.

■

Entering a password incorrectly 3 times in a row causes the keyboard and mouse to be locked out
and [System Disabled] to be displayed. If this occurs, restart the computer by turning off and on
the power with the power switch and use the correct password on reboot.

■

If you make an error when re-entering the password a Warning will be displayed. To try again press
[Enter], then retype the password, or press [Esc] to abort the password process.

■

If the Security Panel on Resume is Enabled and the Password on Boot is Disabled you will not have
to type your password upon resuming the system from the Suspend or Save-to-Disk modes. Power
Management Security will work only if Password boot is enabled.

Figure 14. Security Menu

19

LifeBook T Series BIOS

Table 14: Fields, Options and Defaults for the Security Menu

Menu Field Options Default Description

Supervisor
Password is:

User Password is: –— Clear A display-only field. Set is displayed when the general user

Set Supervisor
Password

–— Clear A display-only field. Set is displayed when the system supervisor password is set

and Clear when it is not.

password is set, and Clear when it is not.

–— [Enter] Sets, changes or cancels the Supervisor Password. The Supervisor Password may

be up to seven characters long and must include only letters or numbers (no
symbols). Passwords are NOT case-sensitive. To cancel a password press the
Enter key instead of entering characters in the Enter New Password field and in
the Re-enter New Password field. When a Supervisor Password is set it must be
used to access the BIOS setup utility.

Set User Password –— [Enter] This field can only be accessed if the Supervisor Password is set. Sets, changes or

cancels the User Password. A User Password may be up to seven characters long
and must include only letters or numbers (no symbols). Passwords are NOT
case-sensitive. To cancel a password press [Enter] key instead of entering char­acters in the Enter New Password field and in the Re-enter New Password field.
When a User Password is set it must be used to access the BIOS setup utility.

Minimum User
Password Length:

Password on Boot:

On Automatic
Wake up:

Boot from
Removable Media:

Flash Write:

–— [0] Supervisor can set password length (0 to 8) for user password. User cannot set a

password shorter than the minimum length.

■

Disabled

■

First Boot

■

Every Boot

■

Disabled

■

Enabled

■

All

■

Supervisor only

■

Disabled

■

Enabled

[Disabled] When set to First Boot, a password (User or Supervisor) is required just once

[Disabled] When disabled, password entry is not required when the system wakes up auto-

[All] Supervisor only allows access to boot the computer to removable media after

after the Power On Self Test (POST) before the operating system will be read
from a disk. When set to Every Boot, a password (User or Supervisor) is required
every time after the Power On Self Test (POST) before the operating system will
be read from a disk. When set to Disabled no password is required.

matically. When enabled, password entry is required upon wake up.

the Supervisor Password is entered.

[Enabled] When disabled, the BIOS Flash memory will be write protected.

Hard Disk Security: –— –— Configures hard disk security features

Owner

–— –— Sets Owner information.

Information:

TPM (Security
Chip) Setting

___ ___ Opens the Trusted Platform Module (TPM) Security Chip Setting submenu to

configure the Security Chip.

Exiting from the Security Menu

When you have finished setting the parameters on the Security Menu, you can either exit from setup utility or move to
another menu. If you wish to exit from setup utility, press the [Esc] key to go to the Exit Menu. If you wish to move to
another menu, use the cursor keys.

20

Hard Disk Security Submenu of the Security Menu

F1 Help
ESC Exit

Select Item
Select Menu

-/Space

Enter

F9 Setup Defaults
F10 Save and Exit

Change Values
Select Sub-Menu

▲

Item Specific HelpHard Disk Security

Drive0: Clear
Set Master Password [Enter]
Set User Password [Enter]
Drive1: Not Available
Set Master Password [Enter]
Set User Password [Enter]

Password Entry on Boot: [Enabled]

Phoenix SecureCore(tm) Setup Utility

Info System Advanced Security Boot Exit

The Hard Disk Security submenu is for configuring hard disk security features.

Security Menu

Table 15: Fields, Options and Defaults for the Hard Disk Security Submenu of the Security Menu

Menu Field Options Default Description

Drive0:

Set Master
Password

Set User
Password

Drive1:

___

___

___

___

Figure 15. Hard Disk Security Submenu

Clear Display-only. Default is Clear. When the Drive0 Password has been set, the field

[Enter] Sets, changes or cancels the Drive0 Master Password. The Drive0 Master Password

[Enter] Sets, changes or cancels the Drive0 User Password. The Drive0 User Password may

changes to Set. When this password is set, the primary hard disk drive cannot be
used in another system unless the password is entered.

may be up to seven characters long and must include only letters or numbers (no
symbols). Passwords are NOT case-sensitive. When a Drive0 Password is set, it must
be used to access the hard drive if it is used in another system. Note that the pass­word will not take effect until the system has been rebooted.

be up to seven characters long and must include only letters or numbers (no sym­bols). Passwords are NOT case-sensitive. When a Drive0 Password is set, it must be
used to access the hard drive if it is used in another system. Note that the password
will not take effect until the system has been rebooted.

Clear Display-only. Default is Clear. When the Drive1 Password has been set, the field

changes to Set. When this password is set, the primary hard disk drive cannot be
used in another system unless the password is entered. When only one drive is
installed (Drive 0:), [Not available] appears here.

21

LifeBook T Series BIOS

Table 15: Fields, Options and Defaults for the Hard Disk Security Submenu of the Security Menu

Menu Field Options Default Description

Set Master
Password

Set User
Password

Password Entry on
Boot:

___

___

■

Disabled

■

Enabled

[Enter] Sets, changes or cancels the Drive1 Master Password. The Drive10 Master Password

[Enter] Sets, changes or cancels the Drive1 User Password. The Drive1 User Password may

[Enabled] When set to disabled, entry of a Hard Disk Password is not required before OS boot.

may be up to seven characters long and must include only letters or numbers (no
symbols). Passwords are NOT case-sensitive. When a Drive0 Password is set, it must
be used to access the hard drive if it is used in another system. Note that the pass­word will not take effect until the system has been rebooted.

be up to seven characters long and must include only letters or numbers (no sym­bols). Passwords are NOT case-sensitive. When a Drive0 Password is set, it must be
used to access the hard drive if it is used in another system. Note that the password
will not take effect until the system has been rebooted.

(The hard disk is still password-protected without password entry.)

22

Security Menu

Owner Information Submenu of the Security Menu

The Owner Information submenu is for setting owner information. Note that the owner information cannot be set
without having entered a Supervisor Password.

Phoenix SecureCore(tm) Setup Utility

Info System Advanced Security Boot Exit

Item Specific HelpOwner Information

Owner Information Is: Clear

Set Owner Information [Enter]

Foreground Color: [Gray]
Background Color: [Black]

F1 Help
ESC Exit

Select Item
Select Menu

-/Space
Enter

Change Values

▲

Select Sub-Menu

F9 Setup Defaults
F10 Save and Exit

Figure 16. Owner Information Submenu

Table 16: Fields, Options and Defaults for the Owner Information Submenu of the Security Menu

Menu Field Options Default Description

Owner Information
Is:

Set Owner Informa­tion:

Foreground Color:

Background Color:

–— Clear Display only.

–— [Enter] Field to write owner informa-

■

Black

■

Blue

■

Green

■

Cyan

■

Red

■

Magenta

■

Black

■

Blue

■

Green

■

Cyan

■

Red

■

Magenta

■

Brown

■

White

■

Gray

■

Light Blue

■

Light Green

■

Brown

■

White

■

Gray

■

Light Blue

■

Light Green

■

Light Cyan

■

Light Red

■

Light Magenta

■

Yellow

■

Bright White

■

Light Cyan

■

Light Red

■

Light Magenta

■

Yellow

■

Bright White

[Gray] Set foreground color.

[Black] Set background color.

tion, (i.e., name).

23

LifeBook T Series BIOS

F1 Help
ESC Exit

Select Item
Select Menu

-/Space
Enter

F9 Setup Defaults
F10 Save and Exit

Change Values
Select Sub-Menu

▲

Item Specific HelpTPM (Security Chip) Setting

Security Chip: [Enabled]

Current TPM State: Disabled and Deactivated
Change TPM State: [No Change]
Clear Security Chip: [Enter]

Info System Advanced Security Boot Exit

Phoenix SecureCore(tm) Setup Utility

TPM (Security Chip) Setting Submenu of the Security Menu

The TPM (Security Chip) Setting submenu is used to enable or disabled the embedded security chip.

Figure 17. TPM (Security Chip) Setting Submenu

Table 17: Fields, Options and Defaults for TPM (Security Chip) Submenu of Security Menu

Menu Field Options Default Description

Security Chip:

Current TPM State: –— Disabled and Deactivated Indicates the current state of the TPM chip.

Change TPM State:

Clear Security Chip

24

■

Disabled

■

Enabled

■

No Change

■

Disable and
Deactivate

■

Enter [Enter] Allows you to clear the Security Chip. Note that this does

[Enabled] Allows you to enable or disable the security chip. Note

[No Change] Allows you to enable or disable the TPM chip when the

that this is only active if a Supervisor Password has been
entered. A reboot is required after exit to configure the
Security Chip correctly. Clear Security Chip option
becomes selectable after reboot.

Supervisor Password has been set.

not allow you to access already-encrypted data.

F1 Help
ESC Exit

Select Item
Select Menu

Item Specific Help

[Disabled]
Display the logo screen
during boot.

[Enabled]
Display the diagnostic
screen during boot.

Boot Time Diagnostic Screen:
Boot Menu: [Enabled]
Preboot Execution Environment: [Enabled]
Boot Device Priority

▲

-/Space
Enter

F9 Setup Defaults
F10 Save and Exit

Change Values
Select Sub-Menu

▲

[Disabled]

Info System Advanced Security Boot Exit

Phoenix SecureCore(tm) Setup Utility

Boot Menu

BOOT MENU – SELECTING THE OPERATING SYSTEM SOURCE

The Boot Menu is used to select the order in which the
BIOS searches sources for the operating system. Follow
the instructions for Navigating Through the Setup
Utility to make any changes. (See Navigating through the

Setup Utility on page 2 for more information.)

The following tables show the names of the menu fields
for the Boot menu and its submenu, all of the options
for each field, the default settings and a description of
the field's function and any special information needed
to help understand the field's use.

Figure 18. Boot Menu

Table 18: Fields, Options and Defaults for the Boot Menu

Disabled
Enabled

Disabled
Enabled

Disabled
Enabled

[Disabled] Turns on and off display of test results instead of Fujitsu logo screen

[Enabled] When Disabled, the Boot Menu is disabled and the [F12] key is

[Enabled] Turns on and off the preboot execution environment feature.

Menu Field Options Default Description

Boot-time
Diagnostic Screen:

Boot Menu:

Preboot Execution
Environment:

Boot Device
Priority

■

■

■

■

■

■

— — This menu allows setting up the source for the operating system.

during Power On Self Test.

ignored. When Enabled, the Boot Menu is enabled.

See “The Boot Device Priority Submenu” in the following section.

25

LifeBook T Series BIOS

F1 Help
ESC Exit

Select Item
Select Menu

Item Specific Help

Keys used to view or
configure devices:

<+>/<Space> or <->
moves the device up or
down.
<x> exclude or include
the device to boot.

Boot priority order:
1: Floppy Disk Drive
2: Drive0 HDD: FUJITSU MHY2080BH
3: Drive1 HDD: None
4: CD/DVD Drive
5: NETWORK: Intel LAN
6:
7:
8:
Excluded from boot order:
: USB MEMORY: None
: USB HDD: None
: AMT: None

-/Space
Enter

F9 Setup Defaults
F10 Save and Exit

Change Values
Select Sub-Menu

▲

Boot Device Priority

Phoenix SecureCore(tm) Setup Utility

Info System Advanced Security Boot Exit

Boot Device Priority Submenu of the Boot Menu

The Boot Device Priority submenu is for setting the order of checking of sources for the operating system.

■

Be careful of the operating environment when booting from a CD or you may overwrite files by mistake.

■

A bootable CD-ROM has either a floppy disk format or a hard drive format. When the CD-ROM is used,
drive allocations change automatically without changing the BIOS setup. If a floppy disk format is used,
the CD-ROM becomes Drive A. The CD-ROM will only take drive C: (hard drive format) if the internal
hard drive is not present or disabled. The bootable CD-ROM can never use a C: designation if a formatted
internal hard drive is present since the C: designator is always reserved for the hard drive.The boot
sequence ignores the new drive designations, but your application software will use the new designations.

Figure 19. Boot Device Priority Submenu

Table 19: Fields, Options and Defaults for the Boot Device Priority Submenu of the Boot Menu

Menu Field Description

Boot priority order:
1: Floppy Disk Drive
2: Drive0:
3: Drive1:
4: CD/DVD Drive
5: NETWORK:
6:
7:
8:
Excluded from boot order:
: USB MEMORY:
: USB HDD:
: AMT:

Exiting from Boot Menu

When you have finished setting the boot parameters with the Boot Menu, you can either exit from the setup utility or
move to another menu. If you wish to exit from the setup utility press the [Esc] key to go to the Exit Menu. If you wish

The boot selections determine the order in which the BIOS searches for the operating system during a
startup sequence. To change the order, highlight one source by using the [up] or [down] cursor keys and
then press the [+] or [-] key to change the order number. Tapping [x] removes from the list a device that is
not installed. Tapping [x] on an item in the Excluded list adds the device to the Boot priority list. Be sure to
save your changed order when you exit the BIOS setup utility.

NOTE: Be aware that if you use the CD-ROM drive as the first boot device, certain files may be
overwritten, depending upon your operating environment.

to move to another menu, use the cursor keys.

26

EXIT MENU – LEAVING THE SETUP UTILITY

Exit Menu

The Exit Menu is used to leave the setup utility. Follow
the instructions for Navigating Through the Setup
Utility to make any changes. (See Navigating through the

Setup Utility on page 2 for more information.)

Phoenix TrustedCore(tm) Setup Utility

Info System Advanced Security Boot Exit

Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
Save Changes and Power Off

F1 Help
ESC Exit

Select Item
Select Menu

-/Space Change Values
Enter Select Sub-Menu

Figure 20. Exit Menu

Table 20: Fields, Options and Defaults for the Exit Menu

The following table shows the names of the menu fields
for the Exit menu, the default settings and a description
of the field's function and any special information
needed to help understand the field's use.

Item Specific Help

Exit System Setup and
save your changes to
CMOS.

▲

F9 Setup Defaults
F10 Save and Exit

Menu Field Description

Exit Saving
Changes

Exit Discarding
Changes

Load Setup
Defaults

Discard
Changes

Save Changes Selecting Save Changes will cause the new settings in all menus to be written to the BIOS memory. The message Save

Save Changes
and Power Off

Exit Saving Changes and Exit will store all the entries on every menu of the setup utility to the BIOS memory, then exit
the utility. A confirmation message Save Configuration changes and exit now? [Yes][No] is displayed.

Selecting Exit Discarding Changes and Exit will exit the setup utility with out writing to the BIOS memory. When the
BIOS recognizes this selection it will load the operating system and begin operation.

Selecting Load Setup Defaults will load the factory preset default values for all menu fields, then display the message
Load default configuration now? [Yes] [No]. When confirmed the setup utility will return to the Exit
Menu. To return to another menu follow the directions in the Navigating Through the Setup Utility Section.

Selecting Discard Changes will load the previous values in BIOS memory for all menu fields. The message Load
previous configuration now? [Yes] [No] will be displayed. When confirmed the setup utility will return to
the Exit menu. To return to another menu, follow the directions in the Navigating Through the Setup Utility Section.

configuration changes now? [Yes] [No] will be displayed. When confirmed, the setup utility will return to
the Exit menu. To return to another menu, follow the directions in the Navigating Through the Setup Utility section.

Selecting Save Changes and Power Off will cause the new settings in all menus to be written to the BIOS memory. The
message Save configuration changes and power off now? [Yes] [No] will be displayed. When con­firmed, the system will shut down. If No is selected, the system will return to the Exit menu. To return to another menu,
follow the directions in the Navigating Through the Setup Utility section.

27