Fujitsu Lifebook S762, Lifebook S792 Operating Manual

Notebook

Operating Manual

LIFEBOOK S762 / S792

Congratulations, you have

decided to buy an

innovative Fujitsu product.

The latest information about our products, useful tips, updates etc. is available
from our website: "

http://ts.fujitsu.com"

For automatic driver updates, go to: "http:// support.ts.fujitsu .com/com/supp ort/index.html"

Should you have any technical questions, please contact:

• our Hotline/Service Desk (see Service Desk list or visit:

"

http://ts.fujitsu.com/support/servicedesk.html" )

• Your sales partner

• Your sales office

We hope you really enjoy using your new Fujitsu system.

Copyright

Fujitsu Tec

hnology Solutions 03/2012

Published by

Fujitsu Technology Solutions GmbH
Mies-van-

der-Rohe-Straße 8 (Mies-van-der-Rohe Street No. 8)

80807 Munich, Germany

Contact

h

ttp://t

s.fujitsu.com/support

All rights reserved, including intellectual property rights. Subject to technical alterations. Delive ry subject to availability.
No warranty is offered or liability accepted in regard of the completeness, correctness, or current applicability of any
data or

illustrations. Brand names may be protected trademarks of the respective manufacturer and/or protected
by copyright. Use of these by third parties for their own purposes may constitute an infringement o f the holders’
rights. Further information can be found at "

http://ts.fujitsu.com/terms_of_use.html"

Order No. Fujitsu Technology Solutions Gm bH: A26391-K360-Z320-1-7619, edition 1

LIFEBOOK S762 / S792

Operating Manual

Innovative technology 7
Ports and controls 9
Important notes 13
First-time setup of your device 17
Working with the notebook 20
Security functions 56
Connecting external devices 64
Removing and installing components

during servicing 72
Settings in BIOS Setup Utility 79
Troubleshooting and tips 81
Technical specifications 88
Manufacturer’s notes 90
Index 97

Microsoft, MS, Windows XP and Windows 7 are registered trademarks of the Microsoft Corporation.

Adobe Reader is a trademark of Adobe Systems Incorporated.

MultiMediaCard is a registered trademark of Infineon Technologies AG

Sony and Memory Stick are registered trademarks of Sony Electronics, Inc.

Manufactured under licence from DTS Licensing Limited. DTS and the symbol
are registered trademarks & DTS Boos t is a trademark of DTS, Inc. Product
includes software. © DTS, Inc. All rights reserved.

All other trademarks referenced are trademarks or registe red trademarks of their
respective owners, whose protected rights are acknowledged.

Copyright © Fujitsu Technology Solutions GmbH 2012
All rights reserved, including rights of translation, reproduction by printing, copying
or similar methods, in part or in whole.

In the event of violations, perpetrators will be liable to prosecution for damages.

All rights reserved, including rights created by patent grant or registration of a utility model or design.

Subject to availability and tech nical modifications.

Contents

Contents

Innovativetechnology ................................................................. 7

Furtherinformation ...................................................................... 7

Notational co nventions .................................................................. 8

Portsandcontrols ..................................................................... 9

Importantnotes ........................................................................ 13

Safetynotes ............................................................................ 13

Additional safety notes for devices with radio components . . . . . ............................. 13

Energysaving .......................................................................... 14

Energy saving under W indows ....................................................... 14

Travelling with yournotebook ............................................................ 15

Before youtravel ................................................................... 15

Notebook: transporting ............................................................... 15

Cleaning thenotebook .................................................................. 16

First-time setup o

fyourdevice .........................................................

17

Unpacking and che

cking thedevice ......................................................

17

Selectingalocat

ion .....................................................................

18

Mains adapter con

necting ...............................................................

18

Switchingonthe

device for the first time ..................................................

19

Workingwith thenotebook ............................................................ 20

Status indicators ........................................................................ 20

Switching on the notebook . . . . ........................................................... 23

Notebook: switch ing off .................................................................. 23

Keyboard ............................................................................... 24

Virtualnumerickeypad .............................................................. 26

Key combinations ................................................................... 27

Country and keyboard settings ....................................................... 28

Application keys ........................................................................ 28

Programming the application keys .................................................... 30

Touchpadand touchpad buttons .......................................................... 30

Moving thepointer .................................................................. 30

Selecting an item .................................................................... 31

Executing commands . . . . . ........................................................... 31

Dragging items ...................................................................... 31

Switching the Touchpadon and off .................................................... 31

ScrollWheel . . .......................................................................... 32

Scroll down/forwards or decrease volume ............................................. 32

Scroll up/back orincreasevolume .................................................... 33

Back one pagein Web browser ...................................................... 33

LCD screen ............................................................................ 34

Webcam ............................................................................... 35

Rechargeablebattery ................................................................... 36

Charging, caring for andmaintaining the battery ....................................... 36

Removing andinstalling the battery ................................................... 36

Module ................................................................................. 38

Removing a module . . . . . . ........................................................... 38

Installing a module .................................................................. 39

Optical drive ............................................................................ 39

Handling data carriers ............................................................... 39

Fujitsu Technology Solutions 3

Contents

CD/DVD indicator ................................................................... 40

Inserting or removing adata carrier ................................................... 40

Manual removal (emergency removal) . . . ............................................. 41

Removing and fittingthe dustremovalcover (ventilation slot cover) ......................... 42

Using the power-management features . . ................................................. 43

Memory cards .......................................................................... 44

Supported formats .................................................................. 44

Inserting the memory card ........................................................... 44

Removing thememory card .......................................................... 45

ExpressCards .......................................................................... 46

Inserting the card ................................................................... 46

Removing thecard .................................................................. 47

Loudspeakers and microphones . . ........................................................ 47

Integrated 56k modem . . ................................................................ 48

Connecting notebook modem to telephone wall socket . . . .............................. 48

SIM card ............................................................................... 49

Inserting the SIM card ............................................................... 49

Removing theSIM card .............................................................. 49

Optional Wireless LAN / BlueTooth / UMTS wireless compo nents . .......................... 50

Switching the wireless com ponents on and off ......................................... 50

Setting upWLAN access ............................................................ 51

Access via UMTS ................................................................... 51

Ethernet and LAN ....................................................................... 51

Your Port Replicator (optional) . . . ........................................................ 52

Ports onthe Port Replicator .......................................................... 52

Connecting the notebook to the Port Replicator . . . . . .................................. 53

Connecting the mains adapter to the Port Replicator . .................................. 54

Switching on the notebook via the port replicator . . . . . .................................. 54

Switching off notebookvia PortReplicator ............................................. 54

Disconnecting the notebook from the Port Replicator .................................. 55

Securityfunctions ..................................................................... 56

Configuring the fingerprint sensor ........................................................ 56

Using the Security Lock ................................................................. 57

Configuring password protection inBIOS SetupUtility ...................................... 57

Protecting BIOS Setup Utility (supervisor and user password) . .......................... 57

Password protection for booting of the operating system . .............................. 58

Password protection forthe hard disk ..................................................... 59

Activatinghard diskprotection ........................................................ 59

Deactivatinghard disk protection ..................................................... 60

Boot from Removable Media ............................................................ 60

Owner Information (device-dependent) . . . ................................................. 61

Trusted Platform Module (TPM) (device-dependent) . . . . . .................................. 62

Enabling TPM ....................................................................... 62

Disabling TPM ...................................................................... 62

SmartCard reader ....................................................................... 63

Inserting the SmartCard ............................................................. 63

Connectingexternaldevices ........................................................... 64

Connecting an external monitor . . ........................................................ 65

DisplayPort ......................................................................... 66

Connecting external devices to the parallel or serial port . .................................. 67

Port settings ........................................................................ 67

Device drivers ...................................................................... 67

4 Fujitsu Technology Solutions

Contents

Connecting USB devices . . . . . ........................................................... 68

USB portwith chargingfunction(AnytimeUSB charge) ................................. 69

Connecting an external SATA hard disk (eSATA) . . . .................................... 70

Safe removalof eSATA andUSB devices ............................................. 70

Connecting external audio devices ....................................................... 71

Microphone port/Line In . . . ........................................................... 71

Headphones port/Line Out ........................................................... 71

Removing and installing components during servicing . . . . ............................. 72

Notes oninstalling and removing boards andcomponents .................................. 72

Preparing to remove components . ....................................................... 73

Installing and removing memory expansion . . . . ............................................ 73

Removing thecover ................................................................. 74

Removing memorymodules .......................................................... 74

Installinga memorymodule .......................................................... 75

Attaching the cover .................................................................. 75

Removing andinstalling thehard disk .................................................... 76

Removing acover ................................................................... 76

Removing ahard disk ............................................................... 77

Installinga harddisk ................................................................. 77

Attaching the cover .................................................................. 78

Finishing component removal . ........................................................... 78

Settings in BIOS Setup Utility . . ........................................................ 79

Starting the BIOS SetupUtility ........................................................... 79

Operating BIOS Setup Utility ............................................................. 79

Exiting BIOSSetup Utility ................................................................ 80

Exit Saving Changes - save changes and exit BIOS Setup Utility . . ..................... 80

Exit Discarding Changes – Discard changes an d exit BIOS Setup Utility . . . .............. 80

Load Setup Defaults – Copy Standard Entries . ........................................ 80

Discard Changes – Discard changes without exiting the BIOS Setup Utility . .............. 80

Save Changes - save changes without exiting the BIOS Setup Utility . . . . . . .............. 80

Save Changes and Power O ff ....................................................... 80

Troubleshootingandtips .............................................................. 81

Help ifproblemsoccur ................................................................... 81

Restoring the hard disk contents under Windows . . ........................................ 82

The notebook’s date or time is incorrect ................................................... 82

When certain characters are entered on the keyboard, only numerals arewritten ............. 82

The notebook’s LCD screen remains blank . . . . ............................................ 83

The LCD screen is difficultto read ........................................................ 83

The external monitorremainsblank ...................................................... 83

The external monitoris blank orthe imageis unstable ..................................... 84

The notebook cannot be started . . . ....................................................... 84

The notebook stops working . . ........................................................... 85

The printer does not print . . . . . ........................................................... 85

The radio connection to a network does not work . . ........................................ 85

Acoustic warnings ....................................................................... 86

Error messages on the screen ........................................................... 86

Technical specifications ............................................................... 88

LIFEBOOK ............................................................................. 88

Port replicator (optional) . . . . . . ........................................................... 88

Rechargeablebattery ................................................................... 89

Fujitsu Technology Solutions 5

Contents

Mains adapter . . . ....................................................................... 89

Manufacturer’snotes .................................................................. 90

Energy Star ............................................................................ 90

Disposal and recycling .................................................................. 90

Declarationsof Conformity ............................................................... 90

CE marking ............................................................................ 91

Regulatory notices ...................................................................... 91

Regulatory informa tion for notebooks without radio device .............................. 91

DOC (Industry CANADA) notices . . . . ................................................. 93

FCC regulatory information for not ebooks with radio device . . . .......................... 95

Index .................................................................................. 97

6 Fujitsu Technology Solutions

Innovative technology

Innovative technology

... and ergonomic design make your device a reliable and convenient companion.

The device boots very quickly, is ready for immediate use and offers a particularly
long operating time because of its high capacity battery.

With the user-friendly "BIOS Setup Utility" you can control yo ur no tebook’s hardware and better
protect your system against unauthorised access by using the powerful password properties.

Information on the connections and user components of you r n otebook
canbefoundin"

Ports and controls", Page 9.

Further information

The Windows drivers for your device can be found on our Internet site.
The factory installation of your device does not support any other operating
system. F ujitsu Technology Solutions accepts no liability whatsoever
if any other operating system is used.

Software oriented components of these instructions refer to Microsoft products,
if they come within the scope of the delivery.

If you install other software products, pay attention to the operating
instructions of the manufacturer.

Fujitsu Technology Solutions 7

Innovative technology

Notational conventions

Pay particular attention to text marked with this symbol. Failure to observe
these warnings could p ose a risk to health, damage the device or lead
to loss of data. The warranty will be invalidated if the device becomes
defective through failure to observe these warnings.

Indicates importan t informa

tion for the proper use of the device.

►

Indicates an activity that must be performed



Indicates a result

This font

indicates data entered

using the keyboard in a program dialogue or at

the c ommand line, e.g.

your password (Name123) or a command used to

start a program (star

t.exe)

This font

indicates information that is displayed on the screen by a p rogram, e.g.:

Installation is complete.

This font

indicates

• terms an d texts used in a software interface, e.g.: Click on Save

• names of programs or files, e.g. Windows or setup.exe.

"This font"

indicates

• cross-references to another section, e.g. "Safety information"

• cross-references to an external source, e.g. a web address: For more
information, go to "

http://ts.fujitsu.com"

• Names of CDs, DVDs and titles or designations for other materials,
e.g.: "CD/DVD Drivers & Utilities" or "Sa fety/Regulations" manual

Key

indicates a key on the keyboard, e.g:

F10

This font

indicates terms and texts that are emphasised or highlighted, e.g.: Do
not switch off the device

8 Fujitsu Technology Solutions

Ports and controls

Ports and controls

This chapter presents the individual ha rdware components of your device. It gives an
overview of the displays and connections of the device. Please familiarise yourself
with these components before you start to use the device.

Front

1

5

2

3

4

5

7

8

12

9

6

11

10

1 = WebCam (optional)
2 = Status indicators
3 = Application keys
4 = ON/OFF switch
5 = Speakers
6 = ScrollWheel

7 = Radio components ON/OFF switch
8 = Memory card slot
9 = Touchpad buttons
10 = Fingerprint sensor
11 = Touchpad
12 = Status indicators

Fujitsu Technology Solutions 9

Ports and controls

Left side

1

2

4

3

5

6

1 = DC input connector (DC IN)
2 = USB port with charging function

(USB 3.0 / eSATA)

3 = USB port (USB 3.0)

4 = DisplayPort
5 = Microphone po rt/Line In
6 = Headphones port/Line Out

Right side

1

2

3

4

5

1 = Optiona

l: ExpressCard slot, SmartCard

reader

or u nremovable mSATA module
2 = Module bay with optical drive
3 = USB por

t(USB2.0)

4 = LAN port
5 = Security Lock device

10 Fujitsu Technology Solutions

Ports and controls

Rear

1

2

1 = VGA monitor port 2 = Modem port

Fujitsu Technology Solutions 11

Ports and controls

Bottom

1

2

3

4

6

7

5

1 = Hard disk service compartment
2 = Module release
3 = Battery release
4 = Rechargeable battery

5 = Port replicator port
6 = Battery release
7 = Vent cover

12 Fujitsu Technology Solutions

Important notes

Important notes

ImportantnotesNotes

This chapter contains essential safety information which must be followed

when working with your notebook. Other notes also provide useful information

which will help you with your notebook.

Safety notes

SafetynotesNotes

Please follow the safety notes provided in the "Safety/Regulations" manual

as well as the safety notes given below.

Please pay special attention to the sections in the manual marked

with the symbol on the left.

When connecting and disconnecting cables, observe the relevant

notes in this operating manual.

Read the information on the ambient conditions in the "

Technical specifications",
Page 88 and "First-time setup of yo ur d evice", Page 17 before preparing your

notebook for use and switching it on for the first time.

When cleaning the device, please observe the relevant notes in the
section "

Cleaning the notebook", Page 16.

Pay attention to the additional safety notes for devices with radio components
provided in the "Safety/Regulations" manual.

Please re fer to the notes in the chapter "

Removing and insta lling

components during servicing", Page 72.

This notebook

complies with the relevant safety regulations for data processing

equipment. I

f you have questions about using your notebook in a particular area,

please conta

ct your sales outlet or our Hotline/Service Desk.

Additional safety notes for devices with
radio components

Radiocomponent:WirelessLAN:Bluetooth,safetynotes

If a radio component (Wireless LAN, Bluetooth, UMTS) is integrated in your notebook, you
must be sure to observe the following safety notes when using your notebook:

• Switch off the radio components when you are in an aircraft or driving in a car.

• Switch off the radio components when you are in a hospital, an operating room or near a medical
electronics system. The transmitted radio waves can impair the operation of medical devices.

• Switch off the radio components when you let the device get near flammable
gases or into hazardous environments (e.g. petrol station, paintshops), as the
transmitted radio waves can cause an explosion or a fire.

For information on how to switch radio components on and off, see chap ter

"

Switching the wireless components on and off", Page 50.

Fujitsu Technology Solutions 13

Important notes

Energy saving

NotesEnergyEnergysaving

Switch the notebook off when it is not in use. Switch off external, connected devices if you
are not using them. If you use the energy saving functions, the notebook uses less energy.
You will then be able to work for longer before having to recharge the battery.

Energy efficiency is increased and the environmental impact is reduced .
You save money while protecting the environment.

Energy saving under Windows

► Make use of the power mana gement features (see ""Using the power-management features",

Page 43").

14 Fujitsu Technology Solutions

Important notes

Travelling with your notebook

MobileoperationNotesTransportationNotebook

Please observe the points listed below when travelling with your notebo ok.

Before you travel

► Back up important data stored on your hard disk.

NotebookTravel,notebook

► Switch off the radio component for data security r easons. With data traffic via a wireless

connection, it is also possible for unauthorised third parties to receive data.

Information on activating data encryption is provided in the documentation
for your radio component.

► If you wish to use your notebook during a flight, first check with the flight

attendants if it is OK t o do so.

When travelling in other countries

► If you are travelling abroad , check that the mains adapter can be operated with the

local mains voltage. If this is not the case, obtain the appropriate mains adapter for
your notebook. Do not use any other voltage converter!

► Check whether the local mains voltage and the power cable are compatible. If this is

not the case, buy a pow er cable that m atches the local conditions.

► Enquire with the corresponding government office of the country you will be

travelling in as to whether you may operate the radio component integrated in
your notebook there (see also "

CE marking", Page 91).

Notebook: transporting

Protect the noteboo k from severe shocks and extreme temperatures
(e.g. direct sunlight in a car).

► If your device has an optical drive, remove all data media (e.g. C D, DVD) from the drives.

TransportationNotebook

► Switch the notebook off.
► Unplug the mains ad apter and all external devices from the power socket.
► Disconnect the mains ad apter cable and the data cables for all external devices.
► Close the LCD screen.
► To protect against damaging jolts and bumps, use a notebook carrying

case to transport your notebook.

Fujitsu Technology Solutions 15

Important notes

Cleaning the notebook

Do not clean any interior parts yourself; leave this job to a se rvice technician.

Only use cleaning products designed for comp uters. Normal household
cleaners and polishes can damage the markings on the keyboard and the
device, the paintwork or the notebook itself.

Ensure that no liquid enters the notebook.

The LCD screen very sensitive to scratches. Only clean the display
surface with a very soft, slightly damp cloth.

► Switch the notebook off

.

CleaningNotesNotebookKeyboardTouchpadLCDscreenCr ystalViewdisplay

► In order to prevent accidentially switch ing the device o n, remove the power cable from the mains

adaptor and remove the battery (see "

Removing and installing the battery", Page 36).



The surface can be cleaned with a dry cloth. If particularly dirty, use a cloth which has
been moistened in mild domestic detergent and then carefully wrung out.

To clean the keyboard and the touchpad, if available, you can use disinfectant wipes.

Ensure that no liquid enters the device.

16 Fujitsu Technology Solutions

First-time setup of your device

First-time setup of your devic

e

First-timese tupGettingstarted

Please read the chapter "Important not es", Page 13.

If your device is equipped with a Windows operating system, the necessary
hardware drivers and supplied software are already pre-installed.

Beforeyouswitchonthedeviceforthefirst time, connect it to the mains voltage
using the mains adapter, see "

Mains adapter con necting", Page 18.Themains

adapter m ust be connected during the entire installation process.

A system test is performed when your device is first switche d on. Various messages
can appear. The display may remain dark for a short time or may flicker.

Please follow the instructions on the screen.

NEVER switch off your device during the first-time setup process.

On delivery, the battery can be found in the battery compartment or in the accessories kit.
The battery must be charged if you want to operate your device using the battery.

When used on the move, the built-in battery provides the device w ith the necessary power. You
can increase the operating time by using the available energy-saving functions.

For instructions on how to connect external devices (e.g. m ouse, printer) to your
device, please refer to the operating manual for your device.

Unpacking and

checking the device

Should you discover any damage that occurred during transportation,
notify your local sales outlet immediately!

► Unpack all the individual parts.

PackagingTransport

► Check your

device for any visible damage which may have occurred during transportation.

You ma y n e

ed the packaging in the future, if you need to transport your device.

Fujitsu Technology Solutions 17

First-time setup of your device

Selecting a location

SelectingalocationDeviceMainsadapter

Select a s uitable location for the device before setting it up. Follow
the instructions below when doing so:

• Never place the device or the mains adapter on a heat-sensitive surface.
The surface could be damaged as a result.

• Never place the device on a soft surface (e.g. carpeting, upholstered furniture,
bed). This can block the air vents and cause overheating and damage.

• The underside of the device heats up during normal operation. Prolonged contact
with the skin may become unpleasant or even result in burns.

• Place the device on a stable, flat, non-slippery surface. Please note that the
rubber feet of the device may mark certain types of delicate surfaces.

• Keep other objects at least 100 mm away from the device and its
mains adapter to ensure a dequate ventilation.

• Never cover the ventilation slots of the device.

• Do not expose the device to extreme environmental conditions. Protect
the device from dust, humidity, and heat.

Mains adapter connecting

PreparingforoperationMainsadapter

Observe the safety notes in the enclosed "Safety/Regulations" manual.

The supplied power cable conforms to the requirements of the country in
which you purchased your device. Make sure that the power cable is approved
for use in the country in which you intend to use it.

3

1

2

► Connect the power cable (1) to the

mains adapter.

► Plug the mains cable (2) into a mains outlet.
► Connect the mains ad apter cable (3) to

the DC jack (DC IN) of the device.

18 Fujitsu Technology Solutions

First-time setup of your device

Switching on the device for the first time

Switchingonforthefirsttime

On devices with ON/OF F switch for wireless components: Slide the ON/OFF switch
for wireless components to the ON position before switching on the device.

When you switch on the device for the first time, the s upplied software is
installed and configured. Because this procedure must not be interrupted,
you should set aside enough time for it to be fully completed and connect
the device to the mains using the mains adapter.

During the installation process, DO NOT restart the device unless
you are requested to do so!

To make it easier to use y

our device for the first time, the operating system

is pre-installed on th

e hard disk.

► Switch on your device.

► During installation, follow the instructions on screen.

If a Windows operating system is installed on your device, you will find more
information on the system and drivers, help programmes, updates, manuals etc.
on the device or on the Internet at "

http://ts.fujitsu.com/support".

Fujitsu Technology Solutions 19

Working with the notebook

Working with the notebook

Notebook,operationNotebook

This chapter describes the basics for opera ting your notebook. Please read the chapter
entitled "

Connecting ext ernal devices", Pag e 64 for instructions on how to connect

devices such as a mouse and a printer to the notebook.

Please refer to the notes in "Important notes", Page 13.

Status indicators

Statusindicatorpanel

The LEDs of the status indicators provide information about the status of the power
supply, the drives and the keyboard functions.

Power-on

indicator

Indica

tor is lit

The not

ebook is switched on.

Indic

ator is

flashi

ng

The no

tebook is in power saving mode.

Indi

cator is not

lit

The notebook is switched off or is in Save-to-Disk m ode.

20 Fujitsu Technology Solutions

Working with the notebook

Battery charging indicator

Green:

The mains adapter is connected and the battery or batteries
installed is/are fully charged.

Indicator is lit

Orange:

The mains adapter is connected and the battery or batteries
installed is/are being charged.

Indicator is
flashing

Orange:

The mains adapter is connected and the battery or batteries
installed cannot be charged (the battery is too hot for charging).

Indicator is not
lit

The mains adapter is not connected.

First battery indicator

Green: The mains adapter is con

nected and the first battery is being

charged. The first batt

ery is charged to be tween 50% and 100%

of maximum c apacity.

Amber:

The mains adapter is connected and the first battery is b eing
charged. The first battery is charged to between 13% and 49%
of maximum c apacity.

Indicator is lit

Red:

The mains adapter is connected and the first battery is b eing
charged. The first battery is charged to between 0% and 12%
of maximum c apacity.

Indicator
flashing quickly
(1son/1soff)

Red:

The first battery

is faulty.

Green:

The n otebook is in suspend mode and power is being supplied
by th e first battery. The first battery is charged to between 50%
and 100% of maximum capacity.

Amber: The n otebook is in suspend mode and power is being supplied

by th e first battery. The first battery is charged to between 13%
and 49% of m aximum capacity.

Indicator
flashing slowly
(1son/5soff)

Red: The n otebook is in suspend mode and power is being supplied

by the first battery. The first battery is charged to between 0%
and 12% of m aximum capacity.

Indicator is not
lit

The first

battery is not installed.

Fujitsu Technology Solutions 21

Working with the notebook

Second battery indicator

Green:

The mains adapter is connected and the second battery is being
charged. The second batte ry is charged to between 50% and
100% of maximum capacity.

Amber: The mains adapter is connected and the second battery is being

charged. The second batte ry is charged to between 13% and
49% of maximum capacity.

Indicator is lit

Red: The mains adapter is connected and the second battery is being

charged. The second battery is charged to between 0% and
12% of maximum capacity.

Indicator
flashing quickly
(1son/1soff)

Red:

The second battery is fa

ulty.

Green:

The notebook is in suspend mode and power is being supplied
by the second battery. The second battery is charged to between
50% and 100% of maximum capacity.

Amber: The notebook is in suspend mode and power is being supplied

by the second battery. The second battery is charged to between
13% and 49% of maximum capacity.

Indicator
flashing slowly
(1son/5soff)

Red: The notebook is in suspend mode and power is being supplied

by the second battery. The second battery is charged to between
0% and 12% of maximum capacity.

Indicator is not
lit

The second batt ery is not installed.

Energy saving function indicator

Indicator is lit

The energy saving functions are enabled (e.g. redu ced screen brightness)

Indicator is
not lit

The energy s

aving functions are disabled.

Drive indicator

Indicator

is lit

The hard disk drive o r the CD/DV D in the optical drive of the notebook is being
accessed.

Indicator is not
lit

The hard disk drive or the CD/DVD in the optical drive of the notebook is not
currently being accessed.

Num Lock indicator

Indicator is lit The

Num

key has been pressed. The virtual numerical keypad is activated. You

can ou tput the characters indicated on the upper right of the keys.

Indicator is not
lit

The

Num

key has not been pressed. The virtual numerica l keypad is not active.

22 Fujitsu Technology Solutions

Working with the notebook

Caps Lock indicator

Indicator is lit

The Caps Lock key has been pressed. All the characters you type will appear
in upper case. In the case of ove rlay keys, the character printed on the upper
left of the key will appear when tha t key is pressed.

Indicator is not
lit

The Caps Lock function is not a

ctivated.

Scroll Lock indicator

Indicator is lit

The key comb ination

Fn+Scr

has been pressed. The effect of this varies

between app lica tion s.

Indicator is not
lit

The key combination

Fn+Scr

has not been pressed.

Switching on the notebook

► Open the LCD screen.

Switchingon

► Press the ON/OFF switch for about one

second to switch the notebook on.



The power-on indicator is lit.

Notebook: swit

ching off

Back up your data and close all applications before you switch off your
device. Otherwise data might be lost.

► Shut down the operating system properly

(e. g. from the Windows Start menu, by
clicking on Start – Shut Down – OK).

Notebook

► If the note

book is not switched off

automatic

ally, press the ON/OFF switch

for appro

x. five seconds.

► Close the L CD screen.

Fujitsu Technology Solutions 23

Working with the notebook

Keyboard

KeyboardNumeric keypadNumerickeypadButtons

The keyboard of your notebook is subject to continuous wear through normal
use. The key markings are especially prone to wear. The key markings are
liable to wear away over the life of the notebook.

The keyboard has been desig

ned to provide all the functions of an enhanced keyboard.

Some enhanced keyboard fun

ctions are mapped with key combinations.

The following descriptio

n of keys refers to Windows. Additional functions supported by the keys

are described in the relev

ant manuals supplied with your application programs.

The figure below shows how

to access the different characters on keys with overlaid functions.

The example applies when

the Caps Lock key ha s not been activated.

The illustrations show

n below may differ from you r actual device.

0

=

}

+

+

Num

Alt Gr

=

0

}

=

0

}

=

0

}

=

0

}

24 Fujitsu Technology Solutions

Working with the notebook

Key Description

Backspace key

The Ba ckspace key deletes the character to the left of the cursor.

BackspaceBackspace

Tab key

The Tab key moves the cursor to

the next tab stop.

Tabkey

Enter key (return)

The Enter key terminates

a command line. The command you have entered

is executed when you pres

sthiskey.

EnterkeyReturnEnterLinefeed

Caps Loc k key

The Caps Lock key activates the Caps Lock mode, and the corresp onding
icon is displayed in the Windows information area. In Caps Lock mode, all
of the characters you type appea r in upper case. In the case of overlay
keys, the character printed on the upper left of the key will appear when
that key is pressed. To cancel the Caps Lock function, simply press the
Caps Lock key again.

ShiftkeyCap sLock

Shift key

The Shift key ca

uses uppercase characters to appear. In the case of overlay

keys, the chara

cter printed on the upper left of the key appears when that

keyispressed.

ShiftkeyShift

Fn button

The

Fn

key enabl

es the special functions indicated on overlay keys (see

"

Key combina

tions", Page 27).

Fnkey

Cursor keys

The cursor

keys move the cursor in the direction of the arrow, i.e. up, down,

left, or ri

ght.

CursorkeysCursorcontrolkeys

Start key

The Start

key opens the Windows St art menu.

Startkey



Menu key

The Menu key invokes the menu for the marked item.

Fujitsu Technology Solutions 25

Working with the notebook

Virtual numeric keypad

NumerickeypadVirtualnumerickeypadNumLock

To provide the convenience of a numeric keypad, your keyboard is equipped with a virtual
numeric keypad. The special k eys of the virtual numeric keypad are recognisable by the numbers
and symbols printed in the upper right corner of each key. If you ha ve switched on the virtual
numeric keypad, you can output the characters shown on the upper right of the keys.

The keyboard layout shown below may differ from your actual device.

1 = Valid characters when the

Num

key is not activated

2 = Valid characters when the

Num

is activated

Furthe

r information about the status indicators can be found in chapter "

Status indicators", Page 20.

26 Fujitsu Technology Solutions

Working with the notebook

Key combinations

The following description of key combinations refers to functions when using
Microsoft Windows. Some of the following key combinations may not function in
other operating systems and with some de vice drivers.

Key combinations are entered as follows:

► Press and hold the first key in the combination.
► While holding the first key down, press the other key or keys in the combination.

The key combination

Ctrl

+

Alt Gr

or

Ctrl

+

Alt

canbeusedon

external keyboards that do not not feature a

Fn

key.

Combination Description

Sleep mode

Fn+F1Sleepmode

This key combination is used to activate the suspend mode (S3).

Enable/disable loudspeak ers

Fn+F3LoudspeakersLoudspeakers

This key combination switches your notebook’s loudspeakers off
and on.

Switching the touchpad on/off

Fn+F4TouchpadLoudspeakers

This key combination enables and disables the touchpad.

Enlarge display

Fn+F5DisplayFull-screenmode

This key combination enlarges the screen to the full-screen mode or
switches it back to the normal mode.

Decrease screen brightness

Fn+F6Screenbrightness

This key combination decreases the brightness of the screen.

Increase screen brightness

Fn+F7Screenbrightness

This key combination increases the brightness of the screen.

Decrease volume

Fn+F8Volume

This key combination reduces the volume of the integrat ed
loudspeakers.

Volume increase

Fn+F9Volume

This key combination raises the volume of the integrated
loudspeakers.

Fujitsu Technology Solutions 27

Working with the notebook

Combination Description

Toggle output screen

Fn+F10Toggleoutputscreen

If an external monitor is connected, the monitor o n which the output is
to be displayed can be selected with this key combination.

Youcanopttouse:

• just the notebook’s LC D screen

• just the external monitor

• both the LCD screen and the external monitor

+

Ctrl

C

Halt current operation

Ctrl+C

This key combination can be used to halt an operation instantly
without clearing the keyboard buffer.

Switch between open app

lications

With this key combinati

on you can switch between several open

applications.

Alt+Tab

AltCtrl

Del

++

Windows Security/Task Manager

This key combination opens the Windows Security/Task Manager
window.

Ctrl+Alt+Del

Back tab

This key combination moves the cursor back to the previous tabular
stop.

Shift+TabBacktab

Key combinations using the Windows keys are detailed in the manual
for your operating system.

Country and keyboard settings

If you want to change the country and keyboard settings, proceed as follows:

► Enter the settings by clicking Start – (Settings) – Control Pane l – Time, Regional and Language Options.

Application keys

Applicationkeys

Your notebook is equipped with five application keys.

All application buttons are freely programmable, see "Programming

the application keys", Page 30.

28 Fujitsu Technology Solutions

Working with the notebook

Button Description

Lock Workstation key

This key allows you to lock your workstation.

Mobility C enter key

This button starts the Mobility Center.

E key

TheEkeyisas

imple way of activating and deactivating power management functions

(e.g. reduc

e screen brightness), see "

Using the power-management fea tures", Page 43.

I key

With the I k

ey, you can obtain further information about your notebook.

When this

keyispressedinS5mode,thefirst battery indicator lights up and shows the

state o f c

harge of the battery, even if the device is switched off (see "

Status indicators",

Page 20).

Wireless Components key

This application key is used to start the WirelessSelector software. The wireless
components that have been activated in the BIOS Setup can be switched on and off

individually.

Fujitsu Technology Solutions 29

Working with the notebook

Programming the application keys

With the Application Panel you can assign various f unct ions to the application keys.

Windows XP

You will find the Application Panel under Start - (Settings) - Control Panel - Additional
Control Panel Options - Application Panel.

Windows 7:

You will find the Application Panel under Start symbol - Programs - Lifebook Application Panel.

Touchpad and touchpad buttons

Keep the touchpad clean. Protect it from dirt, liquids and grease.

TouchpadTouchpad

Do not use the touchpad if your fingers are dirty.

Do not rest heavy objects (e.g. books) on the touchpad or the touchpad buttons.

1

2

3

1 = Touchpad

2 = Fingerprint sensor

3 = Touchpad buttons

The touchpad

enables you to move the mouse pointer on the screen.

The touchpad

buttons allow you to select and execute commands. They correspon d

to the butto

ns on a conventional mouse.

You can use a

key combination to disable the touchpad, to avoid accidentally moving

the pointe

r on the screen (see also "

Key combinations", Page 27).

Moving the pointer

► Move your finger on the touchpad.

Touch

pad



The pointer will move.

30 Fujitsu Technology Solutions

Working with the notebook

Selecting an item

► Move the pointer to the item you wish to select.

Touchpad

► Tap the touchpad once o r press the left button once.



The item is selected.

Executing commands

► Move the pointer to the fiel

d you wish to select.

Touchpad

► Tap the touchpad twice or press the left button twice.



The command is executed.

Dragging items

► Select the desired item.

Touchpad

► Press and hold the left button and drag the item to the desired position

with the finger on the touchpad .



The item will be moved.

Switching the Touchpad on and off

You can switch the Touchpad on and off using a key combination,
see "

Key combinations", Page 27.

Fujitsu Technology Solutions 31

Working with the notebook

ScrollWheel

The Scro llWheel (1) is an innovative and extremely convenient control. The ScrollWheel
allows you to scro ll up or down i n the active window (e.g. on a website) or forwards a n d
backwards in a document with a single finger movemen t. It makes it very easy for you to
display and read websites, documents and the conten t of windows.

1

Activate the ScrollWheel functions in the Control Panel under mou se properties.

Scroll down/fo rwards or decrease volume

Depending on the selected ScrollWheel mode, you can either scroll down/forwards or decrease the
volume.

► To change the ScrollWheel mode, tap the centre of the ScrollWheel until

the desired mode is displayed.

► Move the cursor to the window you

wishtoselect.

► Move your finger clockwise on the

ScrollWheel.



You can scroll down or forwards or
can decrease the volume.

32 Fujitsu Technology Solutions

Working with the notebook

Scroll up/back or increase volume

Depending on the selected ScrollWheel mode, you can either scroll up/back or increase the volume.

► To change the ScrollWheel mode, tap the centre of the ScrollWheel until

the desired mode is displayed.

► Move the cursor to the window you

wishtoselect.

► Move your finger anticlockwise on

the ScrollWheel.



You can scroll up or back or can
increase the volume.

Back one page in Web b

rowser

► Tap the centre of the ScrollWheel.



The Web browser ret

urns to the

previous page dis

played.

Fujitsu Technology Solutions 33

Working with the notebook

LCD screen

LCDscreenNotes

High-quality TFT displays are installed in notebooks from Fujitsu Technology Solutions GmbH. For
technical reasons, TFT monitors are manufactured for a specific resolution. An optimal, clear
picture can only be ensured with the correct resolution intended for the relevant TF T monitor. A
monitor resolution which differs from the specifi cation can result in an un clear picture.

The screen resolution of the LCD mon itor of your notebook is optimally set at the factory.

The standard of production techniques tod ay cannot guarantee an absolutely fault-free screen
display. A few isolated constant lit or unlit pixels (picture elements) may be pre sent. The maximum
permitted number of pixels faults is stipulated in the international stan dard ISO 9241-3 (Class II).

Example:

A m onitor with a resolution of 1280 x 800 has 1280 x 800 = 1024000 pixels. Each pixe l consists of
three subpixels (red, green and blue), so there are almost 3 million subpixels in total. According to
ISO 9241-3 (class II), a maximum of 2 light and 2 dark pixels and an additional 5 light or 10 dark
subpixels or a corresponding mix may be defective (1 light subpixel coun ts as 2 dark subpixels).

Pixel

A pixel consists of 3

subpixels, normally red, green and

blue. A pixel is the s

mallest element that can be generated

by complete functi

onality of the display.

Subpixel

A subpixel is a sep

arately addressable internal structure

within a pixel tha

t en hances the pixel function.

Cluster A cluster contains two or more defective pixels or

subpixels in a 5 x 5 pixel block.

Background li

ghting

TFT monitors a

re operated with background lighting. The luminosity of the background

lighting can

decrease during the period of use of the noteboo k. However, you can

set the brigh

tness of your monitor individually.

Synchronis

ing the display on the LCD screen and an external monitor

For more in

formation, please refer to the chapter "

Key combinations", Pa ge 27

under "Dis

play o utput, switch between".

34 Fujitsu Technology Solutions

Working with the notebook

Webcam

Webcam

Depending on the device v ariant, a WebCam may be integrated in your notebook.

Depending on the software u

sed, you can use your Webcam to take pictures,

record video clips or take p

art in web chats.

• The picture quality depen

ds on the lighting c onditions and the software being used.

• You can only operate the webcam with a particular application (e.g. an Internet telephony
program or a video conferencing program which supports a webcam).

• When using the webcam the

notebook support must not wobble.

• The webcam automatically adjusts itself to the current light level. For this reason
the LCD screen may flicker while the light level is adjusted.

Further information on using the webcam and on the additional settings
which are possible for your webcam can be found in the help function
of the program which uses the webcam.

If you wish to carry out a function test with your webcam, you can use the
corresponding test software available at "

http://ts.fujitsu.com/support/".

Fujitsu Technology Solutions 35

Working with the notebook

Rechargeable battery

RechargeablebatteryBatteryLife,batteryRechargeablebatteryRechargeablebattery

When not plugged into a mains socket, the notebook runs on its built-in battery. You
can increase the life of the battery by caring for the battery properly. The average
battery life is around 500 charge/discharge cycles.

You can extend the battery life by taking ad vantage of the available energy saving functions.

Charging, caring for and maintaining the battery

BatteryBattery

The notebook battery can only be charged, when the ambient temperature
is between 5°C and max. 35°C.

You can charge the batte ry by connecting the notebook to the mains adapter
(see "

Mains adapter connecting", Page 18).

If the battery is running low you will hear a warning alarm. If you do not connect the mains adapter
within five minutes of the warning alarm described above, your notebook w ill automatically switch off.

monitoring the battery charging level

BatteryBatterystatusmet

er

Windows also has a "Battery status meter" in the taskbar for monitoring the battery capacity. When
you place the mouse pointer on the battery symbol, the system displays the battery status.

Battery storage

BatteryBatterySelf-discharge,batteryChargingcapacity,battery

Keep the battery pack between 0°C and +30°C. The lower the temperature at which
the batteries are stored, the lower the rate of self-discharge.

If you will be storing batteries for a longer period (longer than two months),
the battery charge level should be approx. 30 %. To prevent exhaustive
discharge which would permanently damage the battery, check the level
of charge of the battery at regular intervals.

To be able to make use of the optimal charging capacity of the batteries, the battery
should be completely discharged and then fully recharged.

If you do not use the batteries for long periods, remove them from the
notebook. Never store the batteries in the device.

Removing and installing the battery

Only use

rechargeable batteries approved by Fujitsu Technology

Solutio

ns for your notebook.

Never us

e force when fitting or removing a battery.

Make su

re that no foreign bodies get into the battery connections.

Never s

tore a battery for longer periods in the discharged state. This

can ma

ke it impossible to recharge.

36 Fujitsu Technology Solutions

Working with the notebook

Removing a battery

► Prepare for removal, see chapter " Preparing to remove components", Page 73.

2

1

3

► Slide the release button in the direction of the arrow (1) and hold it in place.
► Slide the release button in direction of the arrow (2).
► Remove the battery from the battery compartment (3).

Installing a battery

2

1

► Position the battery at the edge.
► Insert the battery into the battery compartment until it engages positively (1).
► Slide the release button in the direction of the arrow (2).
► Complete the removal, see chapter "

Finishing component removal", Page 78.

Fujitsu Technology Solutions 37

Working with the notebook

Module

ModulebayModules

The design of your notebook enables the flexible use of notebook batteries and drives. The
following modules can be operated in the module bay of your notebook:

• Second battery

• Second hard disk drive

• Optical drive

• Empty plug-in unit (save weight)

• LIFEBOOK Bay Projector

Only use modules designed for your notebook.

Do not use force when installing or removing the m od ule.

Make sure that no foreign objects enter the module bay.

You can swap modules during operation. This means you do not
need to switch off the notebook.

To replace a module, simply click on the corresponding icon in the

task bar and then on Exit or Select - Exit.

The module can now be remo ved without any further a ctions being necessary.

Removing a module

1

2

ModuleDriveWeig ht

Saver

► Slide the release mechanism (1) in the direction of the arrow and hold.
► Now pull the module (2) out of the module bay.

38 Fujitsu Technology Solutions

Working with the notebook

Installing a module

1

► Place the module in

to the module bay so that the contacts enter first.

► Push the module into the module bay until you feel it locking into place.

Optical drive

Opticaldrive

This product co

ntains a light emitting diode, classified in accordance with IEC

8251:1993: LA

SER CLASS 1, and must therefore not be opened.

Handling data carriers

Handling

Observe the

following guidelines when handling data c arriers:

•Avoidtouc

hing the surface of a data carrier. Only handle data carriers by their edges.

• Always store data carriers in their cases. This will protect the data carrier against
being covered in dust, scratched or damaged in any other way.

•Protecty

our data carriers against dust, mechanical vibrations and direct sunlight.

• Avoid storing a data carrier in areas subject to high temperatures or hu m idity.

You ma y u

se both 8-cm and 12-cm data carriers in the optical drive.

When us

ing a data carrier of lesser quality, vibrations and reading errors may occur.

Fujitsu Technology Solutions 39

Working with the notebook

CD/DVD indicator

CD/DVDindicator

The CD/DVD indicator flashes when a data carrier is inserted. The indicator goes out when
the drive is ready for reading. The indicator lights up when the drive is being accessed.
You may only rem ove the data carrier when the indicator is unlit.

If the CD/DVD indicator does not go out after a data carrier has been inserted, but
instead continues to flash, this means that the drive cannot access the data carrier.

Either the data carrier is damaged or dirty or you are using a data
carrier that the drive cannot read.

Inserting or removing a data carrier

InsertingRemoving

The notebook must be switched on.

2

1

► Push the insert/eject button (1).



The drive tray will open.

► Gently pull the drive tray (2) completely out.

► Place the data carrier in the drive tray with

the printed side facing upwards.

or

► Remove a data carrier that has

been inserted.

► Push in the drive tray until you

feel it lock into place.

40 Fujitsu Technology Solutions

Working with the notebook

Manual removal (emergency removal)

CD/DVD:ManualremovalofdatacarrierEmergencyremovalofdata carrier

In the event of a power failure or damage to th e drive, you can remove the data carrier manually.

1

2

► Switch your notebook off.
► Push a pen or a piece of wire (such as a

paperclip) firmly into the opening (1).



The drive tray is ejected. You can now pull
the drive tray (2) out of the drive.

Fujitsu Technology Solutions 41

Working with the notebook

Removing and fitting the dust removal cover
(ventilation slot cover)

In order to ensure optimum cooling of the components in your notebook, you
should periodically clean the ventilation slot of the h eatsink.

This ensures optimum fan performance. You can achieve the best cleaning
results with a small hand-he ld vacuum cleaner.

If necessary, you can also use a dry brush to release dust from the ventilation slots.

Do not u se any cleaning liquids! Ensure that no liquid enters the device.

To avoid overheating of the device, do not remove the ventilation slot
cover when the device is switched on.

► Prepare for removal, see chapter "

Preparing to remove components", Page 73.

1

2

► Press and hold the lock of the ventilation

slot cover (1) and remove it from its slot (2).

► Clean the dust chamber.

1

► Insert the ve

ntilation slot cover into the

slot (1) at an

angle as shown, and ensure

that you feel

it click into place.

► Complete the removal, see chapter

"

Finishing compo nent removal", Page 78.

42 Fujitsu Technology Solutions

Working with the notebook

Using the power-management features

PowerPowerBattery

The notebook uses less power when the available power-m anagemen t features are used. You
will then be able to work longer when using the battery before having to recharge it.

Power efficiency is increased and environm ental pollution reduced. By
choosing the best power options, you can make sign ificant savings and
at the same time help protect the environment.

When you close the LCD screen, depending on the setting in Windows, the
notebook automatically enters a power saving mode.

We recommend the following settings:

Function On external power On battery power

Turn off monitor After 10 minutes After 5 minutes

Turn off hard disk(s) After 15 minutes After 10 minutes

Energy saving (S3) After 20 minutes After 15 minutes

Hibernate mode (S

4)

After 1 hour After 30 minutes

► Select the power ma

nagement functions in your Control Panel.

► Select the Screen Saver in your Control Panel.

or

► Right-click on the desktop. Switch on the screen saver by clicking Personalization –

Change screen saver.

If you need further information about an option, you can get help with most
settings by pressing

F1

to open the Microsoft Help.

When the notebook is in powe r-saving mode, the following must be remembered:

During power saving mode, open files are held in the main memory
orinaswapfile on the hard disk.

Never turn off your notebook while it is in a power saving mode. If the built-in battery is
nearly empty, close the open files and do not go into power saving mode.

If you do not intend to use your notebook for a long period of time:

► Exit power saving mode if necessary via the mouse or keyboard or by switching on the

notebook.

► Close all opened programs and completely shut down the notebook.

Fujitsu Technology Solutions 43

Working with the notebook

Memory cards

Slot

Your notebook is equipped with an integrated memory card reader.

Observe the manufacturer’s instructions when handling the memory cards.

Memorycard

Supported formats

Your notebook supports the following format:

• SD Memory card

Inserting the memory card

► Carefully slide the memory c ard into the

slot. The label should be facing upward. Do
not apply excessive force, as otherwise the
delicate contact surfaces could be damaged.

Memorycard



Depending on the particular type
used, the memory card may protrude
slightly from the slot.

44 Fujitsu Technology Solutions

Working with the notebook

Removing the memory card

Memorycard

In order to protect your data, always follow the correct procedure
for removing the card outlined below.

You can stop the memory card via the corresponding icon in the task bar:

► Left-click on the icon.
► Select the card you want to stop and remove.
► Press the Enter key.



Wait for the dialogue box which tells you that it is now safe to remove the memory card.

1

2

► On devices with card locking: Press

on the storage card (1).

Memorycard



The storage card is released and
can now be removed.

► Pull the storage card out of the slot (2).

Fujitsu Technology Solutions 45

Working with the notebook

ExpressCards

SlotExpressCard

An ExpressCard slot enab les operation of an ExpressCard/34 or ExpressCard/54.

Consult the documentation supplied by the ExpressCard’s manufacturer
and fo llow the instructions provided.

Never use force when installing or removing an ExpressCard.

Make sure that no foreign objects enter the ExpressCard slot.

Inserting the card

Keep the placeholder for the slot in a safe place. When you remove t he card again you
must reinstall the placeholder. This prevents foreign bodies from getting into the slot.

1

2

► If the eject button (1) is recessed, press it

once so that it d isengages. Now p ress the
eject button again so that the placeholder
protrudes slightly from the notebook.

► Pullthecardplac

eholder out of the slot (2).

► Insert the card into the slot guide with

the connection contacts first.

► Gently push the card into the slot either

until it will go no further or you feel it
engage. Do not use excessive force.

Depending on the type, the card may
protrude slightly from the slot.

Please s

ee the docu m entation relating to the card for driver installation instructions.

46 Fujitsu Technology Solutions

Working with the notebook

Removing the card

Always remove the card according to the rules described below, to
ensure that none of your data is lost.

You can stop the card using the corresponding icon in the task bar:

► Left click on the icon to safely remove hardware, located in the taskbar.
► Select the card you want to stop and remove.
► Press the "Enter" key.



Wait for the dialog b ox which tells you that it is now safe to remove the card.

1

2

► If the eject button is lowered, you must

first cause the eject button to release
from the note book casing. To do this,
press the eject button until it pops out.
Press the eject button (1) so that the card
protrudes a little from the notebook.

► Pull the card out of the slot (2).

► Insert the card placeholder into the

slot guide.

► Carefully slid

e the placeholder for the

card as far as it

willgointotheslot.

Do not use exce

ssive force.

Loudspeakers and microphones

MicrophoneLoudspeaker sBasslouds peaker(subwoofer)Volume control

Information on the exact position of the speakers and microphone can be
found in "

Ports and controls", Page 9.

Please refer to chapter "

Key combinations", Page 2 7 for information on setting the volume

and also enabling/disabling the loudspeakers using key combinations.

If you attach an external microphone, the built-in microphone is disabled.

When you connect headphones or external speakers, the built-in speakers are disabled.

Information on connecting headphones and a microphone can be found
in "

Connecting external devices", Page 64.

Fujitsu Technology Solutions 47

Working with the notebook

Integrated 56k modem

56kmodemModem

The integrated 56k modem supports all data communication applications, such as:

• Modem operation: High-speed downloads at up to 56,000 bit/s (V.9x).
Downward-compatible to V.34 modems.

• Fax operation: Transmitting and receiving at up to 14,400 bit/s

• Simple software-based country adaptations

The modem complies with the EU Directive 91/263/EEC (Telecommunications terminal equipment
directive) and has been checked in agreement with the guideline TBR-2 1.

The modem can be operated in the following countries:

Multifrequency (MFC) dialling: Belgium, Denmark, Germany, Finland, France,
Greece, Great Britain, Holland, Ireland, Iceland, Italy, Luxembourg, Norw ay,
Austria, Portugal, Sweden, Switzerland and Spain.

Pulse dialling: Belgium, France, Holland and Italy.

Also in: Poland, Slovenia, South Africa and Hungary.

Connecting notebook modem to telephone wall socket

If you use a modem, incompatibilities with the local telephone system may result.
This may r esult in poor performance, or the modem may not work at all.

Check whether you need a country-specific telephone adapter (available
as an optional accessory).

The modem cable and the country-specific telephone adapter are not included
in delivery. You can order the se as an option.

Please note that the telephone line is busy and that you cannot use your
telephone if the modem cable is plugged into the telephone wall socket. Pull the
modem cable out of the telephone socket after you have finished your internet
session or the fax mode and reconnect the telephone cable.

4

3

1

2

► Connect the

modem cable to the modem

port of the

notebook (1).

Modem

► Plug the m odem cable (2) into the

country-specific telephone adapter (3).

► Connect t

he modem cable to your

telephon

e wall socket (4).

48 Fujitsu Technology Solutions

Working with the notebook

SIM card

Whether or not your device has a SIM card slot depends on whether or
not you have ordered UMTS functionality.

A SIM Card (Subscriber Identity Mod ule) is a chip card which is inserted in a mobile telephone or
notebook to enable access to a mobile radio network in conjunction with an installed UMTS module.

Follow the instructions supplied by the provider of the SIM card.

The SIM card slot is located in the battery compartment and can only
be accessed when the battery is removed.

Inserting the SIM car

d

► Prepare for installation of the SIM card, see chapter "Preparing to remove components", Page 73.

1

► Slide the SIM card i

nto the slot (1)

until it is felt to e

ngage, as shown in

the battery compa

rtment.

► Complete the installation, see chapter "

Finishing component removal", Page 78.

Removing th

e SIM card

► Prepare for removal of the SIM card, see chapter "Preparing to remove comp onents", Page 73.

1

► Press on th

e edge of the SIM card so that

it jumps u

p slightly out of the slot.

► Pull the SIM card out of the slot in the

direction of the arrow (1).

► Complete the removal, see chapter "

Finishing component removal", Page 78.

Fujitsu Technology Solutions 49

Working with the notebook

Optional Wireless LAN / BlueTooth / UMTS
wireless components

The installation of radio components not approved by Fujitsu Technology Solutions
will invalidate the certifications issued for this device.

Depending on the device configuration you ordered, your device will be
equipped with Wireless LAN, Bluetoot h and / or UMTS.

Switching the wireless components on and off

Before switching on

your device for the first time, the on/off switch for

wireless component

s must be in the "ON" position.

► Slide the ON/OFF switch into the "ON"

position to activate the wireless components.

WirelessLANWirelessLANBlue toothBl ue tooth

or

► Slide the ON /OFF switch to the

"OFF" position to deactivate the
wireless components.

The Bluetooth and UMTS modules and the wireless LAN transmission unit (antenna)
will also be switched off when you switch off the wireless components.

You can also deactivate the wireless components individually in th e BIOS Setup.In

order to b e able to do this, you will e ither need to know the supervisor password
if one has been assigned, or no password must have been assigned.

Pay attention to the additional safety notes for devices with radio components
provided in the "Safety/Regulations" manual.

Details on using Wireless LAN can be found in the online help system
included in the Wireless LAN software.

You can find more information on how to use Bluetooth on the CD you
received with your Bluetooth software.

You can obtain more information on UMTS from your service provider.

50 Fujitsu Technology Solutions

Working with the notebook

Setting up WLAN access

• Requirement: A WLAN must be available and you must have the
corresponding access information.

Information on configuring the WLAN access can be found in the
documentation for your operating system.

Access via UMTS

If you have ordered an integrated UMTS module with your system, you can enjoy the
best reception and maximum energy efficiency, without any disruptive cables or aerials.
The optional UMTS module is ready for use immediately.

If you have no t ord ered a UMTS module, you can purchase the accessories for UMTS reception
from specialised dealers or from your Fu jitsu Technology Solutions dealer.

You wil l find information on establishing the connection with the UMTS network
in the documentation for the hardware used.

Your device can connect with the Internet via UMTS. To do this, use one of
the following types of connection:

• an integrated UMTS m odule (depending on your model variant)

• a USB dongle (a USB stick with your mobile phone provider’s SIM card)

• a UMTS ExpressCard (to be inserted in the ExpressCard slot of your device)

• a mobile end-device (e.g. mobile phone with Bluetooth or cable connection)

Ethernet and LAN

EthernetLAN

The in ternal network module of your notebook supports Ethernet LAN. You can use it to
establish a connection to a local network (LAN = Local Area Network).

2

1

► Connect the network cable to the LAN

port of the notebook (1).

► Connect the network cable to your

network connection (2).

Your n

etwork administrator can help you to configure and use the LAN connections.

The n

etwork cable is not included in the delivery scope. This type of

cabl

e can be obtained from a specialist dealer.

Fujitsu Technology Solutions 51

Working with the notebook

Your Port Replicator (optional)

Your Port Replicator is a device that enables you to quickly connect your notebook
to your peripherals, such as a monitor, printer etc.

The features offered by the Port Replicator include standard ports for
monitor, audio, mouse and keyboard.

You need only dock the notebook in order to use your peripheral devices.

Ports on the Port Replic

ator

1

2

3

5

6

7

8

9

10

11

13

12

14

4

1 = Kensington Lock
2 = LAN port
3 = VGA monitor port
4 = DVI port
5=Serialinterface
6=Paral

lel port
7 = eSATA port
8=USBpo

rts

9 = USB port
10 = Headphon

es port/Line Out
11 = ON/OFF switch
12 = Unlocki

ng lever

13 = Connector on the Port Replicator for the

docking port on the bottom of the notebook

14 = DC inp

ut connector (DC IN)

52 Fujitsu Technology Solutions

Working with the notebook

Connecting the notebook to the Port Replicator

If you connect th e notebook to the Port Replicator during operation, problems can
occur. We recommend that you switch off the notebook beforehand.

The mains adapter must be connected to the Port Replicator when the
notebook is connected to the Port Replicator.

We recommend that the notebook is not operated with the LCD screen closed when
the notebook is connected to the Port Replicator. The resulting overheating can
cause reduced performance and increas ed activity of the integrated fan.

PortReplicator

► Switch the notebook off.
► Remove the mains plug for the mains adapter from the mains socket.
► Disconnect the ma ins adapter cable from the DC socket (DC IN) of the notebook.

1

► Position the n otebook so that it is in line with the back edge of the Port Replicator.
► Place the no tebook onto the Port Replicator (1) and ensure that it locks into place correctly.

Fujitsu Technology Solutions 53

Working with the notebook

Connecting the mains adapter to the Port Replicator

1

2

3

► Connect the mains adapter cable to the DC

jack (DC IN) of the Port Replicator (1).

► Connect the power cable to the

mains adapter (2).

► Plug the power cable into the mains

socket (3).

When the notebook is conne cted to a Port Replicator, the operating system creates
a hardware profile for the "Docked" mode. In this profile, for example, the setting is
saved as to which monitor was last used for output. This pro file will b e loaded, as
soon as the notebook is connected to a Port Replicator of the same type.

Switching on the notebook via the port replicator

► Press the ON/O

FF switch on the port

replicator to

switch the notebook on.



The power-on i ndicator of the Port
Replicator lights up.

Switchi

ng off notebook via Port Replicator

► Close all applications and shut down your operating system (please refer

to the manual for the operating system).

If the notebook cannot be shut down properly, press the ON/OFF button
on the Port Replicator for approx. four seconds. The notebook will switch
off. Any unsaved data may however be lost.

54 Fujitsu Technology Solutions

Working with the notebook

Disconnecting the notebook from the Port Replicator

Problems may occur if the notebook is removed from the Port Replicator during
operation. We recommend that the notebook is switched off or that the appropriate
undocking function provided by the operating system is executed.

► Switch the notebook off.

2

1

► Pull the u nlocking lever in the direction of the arrow (1), until you hear the notebook unlatch.
► Lift off the notebook (2).

Fujitsu Technology Solutions 55

Security functions

Security functions

Securityfunctions

Your notebook has several security features that you can use to secure your
system from unau thorised access.

This chapter explains how to use each function, and what the benefits are.

Please rem ember that in some cases, for example, forgetting your password,
you may be locked out and unable to access your data. Therefore,
please note the following information:

• Make regular backups to external data c arriers such as external hard
drives, CDs, DVDs or Blu-ray Discs.

• Some security functio

ns need you to choose passwords. Make a note

of the passwords and ke

ep them in a safe place.

If you forget your passwords y ou will need to contact the our Service
Desk. Deletion or resetting of passwords is not covered by your warranty
and a charge will be made for assistance.

Configuring the fingerprint sensor

FingerprintsensorFingerprintsensor

The fing erprint sensor can record an image of a fingerprint. With additional fingerprint
software, this image can be processed and used instead of a password.

1

► You must install the fingerprint software

in order to be able to use the
fingerprint sensor (1).

56 Fujitsu Technology Solutions

Security functions

Using the Security Lock

Your device comes w ith a S ecurity Lock mechanism for the Kensington Lock Cable. You
can use the Kensington Lock Cable, a sturdy steel cable, to help protect your notebook
from theft. The Kensington Lock Cable is available as an accessory.

K

► Fit the Kensington Lock Cable to the

mechanism on your notebook.

UsingtheKensingtonLockCableSecurityLockMechanicalbackupAnti-theftprotection

Attach another Kensington Lock Cable to your Port Replicator to protect
your Port Replicator from theft as well.

Configuring passw

ord protection in BIOS Setup Utility

Before using the various options for password protection in the BIOS Setup utility

to increase data security, please observe the following:

Make a note of the passwords and keep them in a safe place. If you forget your
supervisor password you will not be able to access your notebook. Passwords are
not covered by your warranty and a charge will be made for assistance.

Passwordprotection

Your password can be up to eight characters long and contain letters and numbers.
No distinction is made between uppercase and lowercase.

Protectin

g BIOS Setup Utility (supervisor and user password)

If you have opened these operating instructions on the screen, we recommend that
you print out the following instructions. Because you cannot call the instructions
onto the screen while you are setting up the password.

BIOSSe

tupUtility

You prevent unauthorised use of the BIOS Setup Utility with both the supervisor and the user
password. The supervisor password gives you access to all functions of the BIOS Setup
Utility, while the user password only provides some of the functions. You can only set a

user password if a supervisor password has already been assigned.

Please refer to the ""Settings in BIOS Setup Utility", Page 79 section for a

description of how to call up and operate the BIOS Setup Utility.

Fujitsu Technology Solutions 57

Security functions

Setting supervisor and user password

► Start the BIOS Setup Utility and go to the Security menu.
► Select the Set Supervisor Password field and press the Enter key.



With Enter new Password: you are asked to enter a password.

► Enter the password and press the Enter key.



Confirm new Password requires you to confirm the password.

► Enter the password again and press the Enter key.



Changes have been saved is a confirmation that the new password has been saved.

► To set the user password, select Set User Password and proceed exactly as

when configuring the supervisor password.



If you do not want to change any other settings, you can exit BIOS Setup Utility.

► In the Exit menu, select the option Save Changes & Exit.
► Select Yes and press the Enter key.

PasswordSupervisorpas swordUserpassword



The notebook w ill be rebooted and the new password will come into effect. It will now be

necessary to first enter your supervisor or user password in order to open the BIOS Setup Utility.

Please note that the user password only provides access to a few of the BIOS settings.

Changing the supervisor or user password

You can only change the supervisor password w hen you have logged into the

BIOS Setup Utility with the supervisor password.

PasswordSupervisorpasswordUserpassword

► Call the BIOS Setup Utility andgototheSecurity menu.

► When changing the password, proceed exactly as for password assignment.

Removing passwords

To remove a passw ord (without setting a new password) perform the following steps:

PasswordSupervisor

password

Userpasswo

rd

► Start the BIOS Setup Utility and go to the Security menu.
► Highlight the Set Supervisor Password or Set User Password field and press the Enter key.



You will be requested to enter the current password by the Enter Current Password prompt.
You will be requested to enter a new password by the Enter New Password prompt.

► Press the Enter key twice.

► In the Exit menu, select the option Save Changes & Exit.
► Select Yes and press the Enter key.



The notebook will now reboot with the password removed.
Removing the supervisor password simultaneously deactivates the user password.

Passw

ord protection for booting of the operating system

With the supervisor password you have set in the BIOS Setup Utility (see

section "

Setting superviso r and user password", P age 58), you ca n also

prevent booting of the operating system.

Operatingsystem

58 Fujitsu Technology Solutions

Security functions

Activating system protection

► Start the BIOS Setup Utility and go to the Se curity menu.

Operatingsystem

► Select the PasswordonBootoption and press the Enter key.
► Select the desired option (Disabled, First Boot or Every B oot) and press t he Enter key
► Select the Save Changes & Exit option under Exit.



The n otebook will reboot. You will be prompted to enter your password ( the supervisor password).

Deactivating system protection

► Start the BIOS Setup Utility and go to the Se curity menu.

Operatingsystem

► Select the PasswordonBootoption and press the Enter key.
► Select the Disabled option and press the Enter key.



If you do not want to change any other settings, you can exit BIOS Setup U tility.

► Select the Save Changes & Exit option under Exit.



The noteboo k will reboot. The system is no longer password-protected.

Password protection for the hard disk

Passwordprotec

tion:

The had disk password prevents unauthorised access to the hard disk drives
and is checked internally each time the system is booted. T he condition for this
is that you have assigned at least the supervisor password.

Activating hard disk protection

► Call up the BIO

SSetupand select the Security menu.



If you have not assigned BIO S passwords yet, define the supervisor and the user
password now, if desired (see "

Security functions", Page 56).

► Mark the Har

d Disk Security field and press the Enter key.

► In the Drive0 area mark the Set Master Password field and press the Enter key.



Enter new P

assword then appears and you are asked to enter a password.

► Enter the password and press the Enter key.



Confirm ne

w Password requires you to confirm the password.

► Enter the passwo rd again and press the Enter key.



Setup Not

ice: Changes have been saved is displayed to confirm that the

new pass

word has been saved.

► To assign the password for the second hard disk (Drive1), go to the Drive1 area and

select the field Set Master Password, then proceed in exactly the sa m e way as for
setting up the password for the first hard disk (Drive0).



The fie

ld Password Entry on Boot is set to Enabled by default. You can exit the BIOS

Setup

once you have finished changing the settings.

► From the Exit menu, choose the option Exit Saving Changes.

► Pres

s the Enter key and select Yes.



The notebook reboots and your hard disk is now protected with a passw ord. The system
will ask you to enter the password when the notebook is restarted again.

Fujitsu Technology Solutions 59

Security functions

Deactivating hard disk protection

To cancel a password without setting a new one, proceed as follows:

► Call up the BIOS Setup and select the Security menu.
► Mark the Hard Disk Security fie ld and press the Enter key.
► In the Drive0 area mark the Set Master Password field and press the Enter key.



You will be initially requested to enter the old password by the Enter current Password prompt.
You will then be requested to enter a new password by the Enter new Password prompt.

► After entering the password, press the Enter key three times.

► From the Exit menu, choose the option Exit Saving Changes.
► Press the Enter key and select Yes.



The notebook reboots, and password protection for the hard disk is cancelled.

► To cancel the password for the second hard disk (Drive 1), go to the Drive1 area

and select the field Set Master Password, then proceed in exactly the same way as
for cancelling the password for the first hard disk (Drive0).

Boot from Removable Media

With this BIOS feature, you can manage/control unauthorised booting of an operating
system from external media (e.g. USB stick, USB CD-ROM drive etc.) We recommend
that you configure the hard disk as the first boot medium in order to prevent access
to your system by boot CDs and bootable media.

The c ondition for this BIOS feature is that you have assigned at
least the supervisor password.

► Call up the BIOS Se tup and select the Security menu.
► Highlight the Boot from Removable Media field and press the Enter key.
► Select the entry All (if you want everyone to be allowed to boot) or Supervisor Only (if you

only want the supervisor to be authorised to do this) and press the Enter key.



If you do not want to change any other settings you can exit the BIOS Setup.

► From the Exit menu, choose the option Exit Saving Changes.
► Press the Enter key and select Yes.



The notebook will restart and the settings will be adopted.

60 Fujitsu Technology Solutions

Security functions

Owner Information (device-dependent)

The BIOS feature Owner Information enables you to enter up to 80 characters of text

which is displayed in the bottom left corner of the screen before the operating system
boots up. You could use this featu re for example to put your name and telephone
number on the notebook in case it is lost or stolen.

Requirements:

• You have been assigned at least the supervisor password.

•IntheBOOT menu, the Boot time dia gnostic screen option is set to enabled.

► Call up the BIOS Setup a

nd select the Security menu.

► Highlight the Owner Information field and press the Enter k ey.

► Add the text you would

like to enter under Set Owner Information.



Setup Notice: Changes have been saved is displayed to confirm that the text has been saved.

► From the Exit menu,

choose the option Exit Saving Changes.

► Press the Enter key and select Yes.



The notebook will

restart an d the Owner Information will be adopted.

Fujitsu Technology Solutions 61

Security functions

Trusted Platform Module (TPM) (device-dependent)

TPMTrustedPlatformModule

To use the TPM, you must activate the TPM in the BIOS Setup before the software

is installed. The condition for this is that you have assigned at least the supervisor
password (see "

Security functions", Page 56).

Enabling TPM

• Requirement: You have assigned a supervisor password, see "Security functions", Pa ge 56.
► Call up the BIOS S e tup an

d select the Security menu.

► Mark the TPM Security Chip Setting field and press the Enter key.
► Select Enabled to acti

vate the TPM.



Once you have activated the TPM the Clear Security Chip option appears.
Select Clear Securit

y Chip to delete the holder in the TPM. By clicking on Enabled,

all secret keys (e.g

. SRK - Storage Root Keys, AIK - Attestation Identity Keys

etc.) generated by

applications are deleted.

Please note that yo

u will then no longer be able to access the data you have

encrypted wi th th

e keys based on that holder.

► Select the Exit Sa

ving Changes option in the Exit menu.

► Press the Enter key and select Yes.



The notebook wil

l restart, and TPM will be enabled after the reboot.

Disabling TPM

• Requirement: You have assigned a supervisor password, see "Security functions", Pa ge 56.

► Call up the BIOS Se tup and select the Security menu.
► Mark the TPM Security Chip Setting field and press the Enter key.
► Select Disabled to deactivate the TPM.
► From the Exit menu, choose the option Exit Saving Changes.
► Press the Enter key and select Yes.



Your notebook will now restart and TPM will be disabled.

62 Fujitsu Technology Solutions

Security functions

SmartCard reader

Securityfunctions,Securityfunctions

Depending on the device configuration level, your notebook is equipped
with a SmartCard reader.

SmartCards are not supplied as standard equipment. You can use all SmartCards that comply with
the ISO standard 7816-1, -2 or -3. These SmartCards are available from various manufacturers.

With the appropriate software you can use your SmartCard as an alternative to password protection,
but also as a digital signature, for encrypting your e-mails or for home banking.

We recommend that you always use two SmartCa rds. Always keep one of the SmartCards
in a safe place if you are carrying the other SmartCard with you.

In order to be able to take advantage of all the security features of y our notebook, you
will need a CardOS SmartCard from Fujitsu Technology Solutions.

The SmartCard can only be used with a PIN, offering maximum protection even if
you lose the SmartCard. In order to maximise your security, the CardOS SmartCard
is disabled if three incorrect attempts are made to enter the PIN.

When you use the CardOS SmartCard for the first time, you will either need to enter the
preset PIN "12345678" or the PIN given to you by your systems administrator.

Inserting the S

martCard

Do not use force when inserting and removing the SmartCard.

Make sure that foreign o bjects do not fall into the SmartCard reader.

► Slide the SmartCard into the SmartCard

reader with the chip facing upwards (on
some variants it faces down) and to the front.

Fujitsu Technology Solutions 63

Connecting external devices

Connecting external devices

Always refer to the safety information provided in "Important notes", Page 13 before
connecting or disconnecting any devices to or from your noteboo k.

Always read the documentation supplied with the device you wish to connect.

Never connect or disconnect cables during a thunderstorm.

Never pull at a cable when disconnecting it. Always grasp the plug.

Follow the steps below in order, when connecting or disconnecting
devices to your notebook:

With some devices such as USB devices, it is not necessary to switch off
the notebook and the device before connecting/disconnecting. For more
information about whether or not devices need to be switched off, please refer
to the documentation supplied with the external device.

Some of the external devices require special drivers (see the operating
system and external device documentation).

Connecting devices to the notebook

1. Turn off your notebook and all external devices.

2. Unplug your not

ebook and all devices from the mains sockets.

3. Connect the cables for your external devices following the instructions.

4. Plug all power

cables into the mains sockets.

DevicesPeripheralde

vices

Disconnecting devices from the notebook

1. Turn off your notebook and all external devices.

2. Unplug your

notebook and all devices from the mains sockets.

3. Disconnect the cables for your external devices following the instructions.

DevicesPeripheraldevices

64 Fujitsu Technology Solutions

Connecting external devices

Connecting an external monitor

The notebook itself does not have a DVI port. The optional Port Replicator
available for your notebook provides this port.

An analogue monitor is connected to the analogue VGA monitor port, a digital monitor to
the DVI monitor port. Screen output is limited to a maximum of two screens at any one
time (see "

Key combinations", Page 27, section "Toggle output screen").

MonitorVGAconnec tionsocketScreenportMonitorport

Digital DVI monit

or port

Analogue VGA monitor port

► Switch off the notebook and the external monitor.
► Plug the data cable of the external monitor into the monitor port.
► First switch on the external monitor and then the notebook.

You can also switch back and forth between the external monitor and the notebook’s
LCD monitor, see chapter "

Key combinations", Page 27.

You can display the same picture on the external monitor and the
notebook LCD screen simultaneously.

Fujitsu Technology Solutions 65

Connecting external devices

DisplayPort

DisplayPort

You can connect a monitor, a n LCD TV or a plasma TV with a suitable connector via the DisplayPort.

► Connect the data cable to the

external device.

► Connect the data cable to the DisplayPort

of the notebook.

Some LCD televisions have only two loudspeaker connections and therefore
cannot reproduce Dolby digital or DTS. In order to reproduce the sound, you

must go into Windows Vista and adjust the sound settings.

Proceed as follows:

► Select Start symbol – (Settings) – Control Panel – Hardware and Sound – Sound.
► Mark Realtek HDMI Output.
► Select Properties – Supported formats.
► Deactivate the settings DTS audio and Dolby digita l.
► Confirm the settings with OK.

66 Fujitsu Technology Solutions

Connecting external devices

Connecting external devices to the parallel
or serial port

ParallelportSerialportParallelportSerialportExternaldevicesDevices

If you w ish to operate devices at a serial or parallel port, use the optional
Port Replicator available for your notebook.

External devices can be c

onnected to the parallel or serial port (e.g. a printer or a modem).

► Connect the data cable to

the external device.

► Depending on the device, connect the data cable to the parallel port or the serial port.



For an exact descripti

on of how to connect external devices to the corresponding

port, please s ee the ex

ternal device documentation.

Port settings

ParallelportSerialport,

You can change the port settings (e.g. address, interrupt) in the BIOS Setup.

Device drivers

DevicedriversDevicedrive rs,

The devices connected to the parallel or serial port require drivers. Your operating
system already includes many drivers. If the required drive is missing, install it. Current
drivers are usually available on the Internet or will be supplied on a data medium.

Fujitsu Technology Solutions 67

Connecting external devices

Connecting USB devices

USBports

On the USB ports, you can connect external devices that also have a USB port
(e.g. a DVD drive, a printer, a scanner or a modem).

USB devices are hot-pluggable. This means you can connect and disconnect
devices while your operating system is running.

USB 1.x has a maximum data transfer rate of 12 Mbit/s.

USB 2.0 has a data transfer rate of up to 480 Mbit/s.

USB 3.0 has a data trans

ferrateofupto5Gbit/s.

Additional informati

on can be found in the documentation for the USB devices.

► Connect the data cable to the

external device.

► Connect the data cable to a USB

port of the notebook.

Device drivers

USB devices will be automatically recognised and installed by y our operating system.

68 Fujitsu Technology Solutions

Connecting external devices

USB port with charging function (Anytime USB charge)

USBchargingfunction

It is recommended that the notebook be operated with the power s upply connected
whenever the USB port with charging function is in use, as this function will drain
the battery more quickly if an external USB device is being charged.

The power supply unit must already be co nnected when the notebook is
switched off, as otherwise the USB charging function will be disabled and
the connected USB devices will not be charged.

Some USB devices (e.g. mobile telephones) require a driver in order to utilise the
USB charging function. In this c ase the USB charging function will not work when the
notebook is switched off, as no drivers are active when the notebook is switched off.

You can use this

USB port to charge or supply power to a USB device (e.g. to charge a PDA

or a mobile phon

e or to connect a USB lamp), even if the notebook is switched off.

Fujitsu Technology Solutions 69

Connecting external devices

Connecting an external SATA hard disk (eSATA)

An external SATA hard disk can be connected at the eSATA port. This allows you
to expand the internal h ard disk capacity as you wish.

The length of the eSATA cable must not exceed 2 metres. Consult a specialist
dealer for advice on which eSATA data cable is suitable for your external eSATA
hard disk. Make sure that the hard disk has its own external power supply.

The data transfer rate is up to 2,400 Mbit/s.

eSATA

► Connect the data cable to the external

device.

► Connect the data cable to the eSATA port.

Device drivers

The eSATA hard disk is automatically recognised by you r operating system and installed.

You will find more information in the documentation for the extern al SATA
hard disk and the operating system.

Safe removal of eSATA and USB devices

Always corre

ctly remove the device according to the rules described below,

to ensure tha

t none of your data is lost.

► Left-click on the symbol to remove hardware safely.
► Select the

device you wish to shut down and remo ve.

► Press the "Enter" key.



Wait for t

he dialogue box which tells you that it is now safe to remove the device.

70 Fujitsu Technology Solutions

Connecting external devices

Connecting external audio devices

Microphone port/Line In

Audiodevices,connectingAudioportsMicrophone,conn ecting

The microphone port/Line In allows you to connect an external microphone, a MiniDisc
player, MP3 player, CD player or a tape deck to your not ebook.

► Connect the audio cable to the

external device.

► Connect the audio cable t

o the microphone

port/Line In of the note

book.

Headphones port/Line Out

Audiodevices,co

nnecting

AudioportsHeadphones,conn

ecting

Headphones or external loudspeakers can be connected to your notebook via the headphones port.

► Connect the data cable to the

external device.

► Connect the signal cable to the

headphones/Line Out port on the notebook.

When you connect headphones or external loudspeakers, the built-in
loudspeakers are disabled.

If you purchase a cable from a retailer, please note the following:

If you want to connect headphones or a speaker you will need a "3.5 mm jack plug".

Fujitsu Technology Solutions 71

Removing and installing com ponents

during servicing

Removing and installing compo

nents

during servicing

Only qualified technicians should repair your notebook. Unauthorised
opening or incorrect repair may greatly endanger the user (electric shock,
fire risk) and will invalidate your warranty.

Components

Servicing

After consulting the Hotline/Service Desk, you may remove and install the
components described in this chapter yourself.

If you remove and install components without consulting the Hotline/Service
Desk, then the warranty of your notebook will be voided.

Notes on installing and removing boards
and components

• Switch the notebook off and pull the power plug out of the ma ins socket.

• Always remove the battery.

• Take care when you use the locking mechanisms o n the battery and any other component.

• Never use sharp objects such as screwdrivers, scissors or knives as leverage to remove covers.

NotesBoardESD

Boards with electrostatic sensitive d evices (ESD) are marked with the label
shown.

When handling boards fitted with ESDs, you must always observe the following
points:

• You must always discharge static build up (e.g. by touching a grou nded
object) before working.

• The e quipment and tools you use must be free of static charges.

• Remove the power plug from the mains supply before inserting or removing
boards containing ESDs.

• Always hold boards with ESDs by their edges.

• Never touch pins or conductors on boards fitted with ESDs.

72 Fujitsu Technology Solutions

Removing and installing components

during servicing

Preparing to remove components

If you are going to remove or change system components, prepare for the removal as follows:

Please observe the safety information in chapter "Important notes", Page 13.

Remove the power plug from the mains outlet !

► Switch the device off.

The device must not be in energy-saving mode !

► Close the LCD screen.
► Remove all the cables

from the device.

► Turn the device over and place it on a stable, flat and clean surface. If necessary, lay an

anti-slip cloth on this surface to prevent the de vice from being scratched.

► Remove the battery

(see "

Removing a battery", Page 37).

Installing and removing memory expansion

MemorymoduleMainmemoryRemovingmemorySystemexpansionSystemexpansi

on

If you are asked by the Ho tline/Service Desk to remove and install the memory
expansion yourself, proceed as follows:

Please observe the safety information in chapter "Important notes", Page 13.

When installing/removing memory m odules, the battery must be removed from
the notebook and the notebook must not be connected to the power supply,
see "

Preparing to remove comp onents", Page 73.

Only use memory expansion modules that have been approved for your
notebook (see "

Technical specifications", Page 88).

Never use force when installing or removing a memory extension.

Make sure that foreign objects do not fall into the memory extension compartment.

You must open the service compartment to remove or install a memory module. On some devices,
opening the compartment may exp ose other com ponents. These components should be removed
and replaced only by auth orised specialists. Therefore, b e sure to observe the following:

Individual components can become very hot during operation. Therefore, we
recommend that you wait one hour after switching off the notebook before removing
or installing memory modules. Otherwise, there is a risk of suffering burns!

As some components are exposed that are sensitive to static electricity, please take
note of chapter "

Notes on installing and removing bo ards and components", Page 72.

Fujitsu Technology Solutions 73

Removing and installing com ponents

during servicing

Removing the cover

► Prepare for mem ory extension, see "Prepa ring to remove components", Page 73.

1

2

► Remove the screw (1).
► Lift the cover off the notebook (2).

Removing memory modules

3

2

1

1

► Carefully push the two mounting

clips outwards (1).

Memoryexpan

sion

Memorymodul

e



The memory module snaps upwards (2).

► Pull the memory module out of its s lot

in the direction of the arrow (3 ).

74 Fujitsu Technology Solutions

Removing and installing components

during servicing

Installing a memory module

2

a

1

► Insert the memory module with t he contacts

and the recess (a) facing the slot (1).

MemoryexpansionMemorymodule

► Carefully push the memory module

downwards until you feel it click
into place (2).

Attaching the cover

2

1

► Place the cover into position, following the direction of the arrow (1).
► Fasten the cover in place with the screw (2).
► Complete the memory extensi on, see "

Finishing component removal", Page 78.

Fujitsu Technology Solutions 75

Removing and installing com ponents

during servicing

Removing and installing the har

ddisk

Removing a cover

2

1

1

► Remove the screw

s(1).

Keep the screws

in a safe place. If you are removing more than one component at

the same time,

store the screws for the individual components separate from each

other. If you i

nstall the wrong screws, components may be damaged.

► Lift the cover off the notebook (2).

76 Fujitsu Technology Solutions

Removing and installing components

during servicing

Removing a hard disk

1

2

► Remove hard disk fix

ture (1).

► Lift the hard disk out of the hard disk compartment (2).

Installing a hard disk

1

2

► Insert the hard disk into the hard disk compartment (1). Ensure that the contacts engage.
► Re-attach the har d disk fixture (2).

Fujitsu Technology Solutions 77

Removing and installing com ponents

during servicing

Attaching the cover

2

2

1

► Place the cover in the correct mounting position (1).
► Fasten the screws (2).

Finishing component removal

After you have removed or changed the s ystem components as you required, please
prepare your device for operation again as follows:

► Install the battery again (see "

Installing a battery", Page 37).

► Turn the notebook the right way up again and place it on a flat surface.
► Reconnect the cables that you disconnected before.

78 Fujitsu Technology Solutions

Settings in BIOS Setup Utility

Settings in BIOS Setup Utility

BIOSSetupUtilitySystemsettings,BIOSSetupUtilityConfiguration,BIOSSetupUtilitySetupSystemconfigurationHardwareco nfigu ration

The BIOS Setup Utility allows you to set the system functions and the hardware

configuration for the notebook.

When it is delivered, the notebook is set to factory default settings. You can

change these settings in BIOS Setup Utility. Any changes you make take effect as
soon as you save and exit the BIOS Setup Utility.

The BIOS Setup Utility program contains the following men us:

About

Displays information relating to the BIO S, processor and notebook

System

Advanced system settings

Advanced

Configuration of various hardware components, such as mouse, keyboard,
processor

Security

Password settings and security functions

Boot

Configuration of the start-up sequence

Exit

Exits the BIOS Setup Utility

Starting the BIOS Setup Utility

► Reboot the note

book (switch off/on or reboot the operating system).

BIOSSetupUtility

► Press and hold function key

F2

.

► If a password

has been assigned, enter the password and press the En ter key.

If you have fo

rgotten the password, contact y our system administrator

or contact o

ur customer service centre.

The BIOS Setup U tility starts.

Operating BIOS Setup Utility

BIOSSetupUtility

Press the

F1

key to display help on the operation of the BIOS Setup Utility. The description

of the individual settings is shown in the right-hand windo w of the BIOS Setup Utility.

With the

F9

key you can load the default s ettings of the BIOS Setup Utility.

► Use the cursor keys

←

or

→

to select the menu you wish to access to make changes.



The m enu is displayed on the screen.

► Select the option you want to ch ange with the cursor keys

↑

or↓.

► Press the Enter key.
► Press the

ESC

key to exit the selected menu.

► For future reference, make a n ote of the change s you have made (for example, in this manual).

Fujitsu Technology Solutions 79

Settings in BIOS Setup Utility

Exiting BIOS Setup Utility

BIOSSetupUtility

You need to select the desired option in the Exit menu and activate it by pressing the Enter key:

Exit Saving Changes - save ch

anges and exit BIOS Setup Utility

► To save the current menu settings and exit the BIOS Setup Utility, select Exit Saving Changes and Yes.



The notebook is rebooted

and the new settings come into effect.

Exit Discarding Changes – Discard changes and
exit BIOS Setup Utility

► To discard the changes, select Exit Discarding Changes and Yes.



The settings in place when BIOS Setup Utility was ca lled remain effective. BIOS
Setup Utility is terminated and the notebook is rebooted.

Load Setup Defaul

ts – Copy Standard Entries

► To copy the standard entries for all menus of the BIOS Setup Utility,

choose Load Setup Defaults and Yes.

Discard Changes – Discard changes without exiting
the BIOS Setup Utility

► To discard the changes you have made, select Discard Changes and Yes.



The settings in place when BIOS Setup Utility was called remain effective.
You can now make additional settings in the BIOS Setup Utility.

► IfyouwanttoexitBIOS Setup Utilitywith these settings, select Exit Saving Changes and Yes.

Save Chan

ges - save changes without exiting

the BIOS Setup Utility

► To save the changes, select Save Changes and Yes.



The changes are saved. You can now make additional settings in the BIOS Setup Utility.

► If you want to exit BIOS Setup Utility with these settings, choose Exit Saving Changes and Yes.

Save Changes and Power Off

► To save the changes and switch off your device, select Save Changes and Power Off and Yes.



The changes are saved. Your d evice is shut down.

80 Fujitsu Technology Solutions

Troubleshooting and tips

Troubleshooting and tips

TroubleshootingTipsFaultTroubleshooting

Follow the safety notes in the "Safety/Regulations" manual when
connecting or disconnecting cables.

If a fault occurs, try to correct it as described. If you fail to correct the problem, p roceed as follows:

► Make a note of the steps and the circumstances that led to the fault. Also

make a note of any error messages displayed.

► Switch the notebook off.
► Please contact the Hotline/Service Desk.

You ca n find the telephone numbers in the service desk list. Please have
the following information re ady when you call:

• The model name and serial number of the notebook. The serial number is
located on a sticke r on the underside of the notebook.

• Notes of any messages that appear on the screen and information on acoustic signals.

• Any changes you have made to the hardware or software since
receiving the notebook.

• Any changes you have made to the BIOS Setup settings since receiving the notebook.

• Your system configuration and all peripheral devices connected to your system.

• Your sales contract.

Our notebooks

have been designed primarily with mobile applications in mind. This

means that con

siderable effort has been made to optimise components and eq uipm ent

in terms of we

ight, space and energy requirements. Depending on the particular

configuratio

n you have purchased, it is possible that functionality may be slightly reduced

compared to a

desktop PC if you are running processor-intensive gaming software, e.g.

games with i

ntensive 3D graphics. Updating your hardware with drivers which have not

been appro

ved by Fujitsu Technology Solutions may result in performance losses, data

losses or m

alfunction of the equipment. A list of approved drivers and current BIOS

versions c

an be downloaded from: "

http://ts.fujitsu.com/support/downloads.html"

Help if pr

oblems occur

Should you encounter a problem with your computer that you can not resolve yourself:

► Note the ID number of your device. The ID number is found on the type rating

plate on the back or underside of the casing.

► For further clarification of the problem, contact the Help D esk for your country (see the Help

Desk list or visit the Internet at "

http://ts.fujitsu.com/support/servicedesk.html"). When you

do this, please have ready the ID nu mber and serial number of your system.

Fujitsu Technology Solutions 81

Troubleshooting and tips

Restoring the hard disk content

s under Windows

Harddisk:Operatingsystem,restoring

You can use the "Windows Recovery CD" (optionally available ) and the "Drivers & Utilities
CD/DVD" to reinstall the operating system.

The instructions are provided on the case of the Recovery CD.

During the reinstall process your personal files and any installed programs
will be deleted. We advise you to backup your files to an external hard
drive, or CD / DVD disk before you start.

► Switch the notebook on.



The following display br

iefly appears on the screen du ring start-up:

<ESC>Diagnostic screen <F12>Boot Menu <F2>BIOS Setup

► When this message appears, press the function key

F12

.

► Insert the "Windows R

ecovery CD" into the optical drive.

► Select CD-ROM and press the Enter key.

► Follow the instruct

ions o n the screen.

After the installation you must install all the drivers again. Some installed hardware
components will not be correctly supported until this has been done.

► Insert the "Drivers & Utilities" CD/DVD into the optical drive. The CD starts automatically.

► Click on the De sk U

pdate button.

► Select Au tomatic driver installation (Express) and click on Start installation.

► Follow the inst

ructions o n the screen.

► Restart your notebook when the driver installation is completed.

The notebook’s date or time is incorrect

SummertimeTime,daylights avingsTimenotcorrectTimenotcorrectIncor rectdate/ti meDateisincorrectBufferbattery,load

Cause Troubleshooting

Time and date are incorrect. ► With the BIOS-Setup-Utility, you can set the

date and time in the main menu.

If the time

and date are still set incorrectly after

switching

on the notebook.

► Please contact your sales outlet or our

Hotline/Service Desk.

When certain characters are entered on the
keyboard, only numerals are written

Abeepsoundseveryseco nd

Cause Troubleshooting

The virtual numeric keypad of your device is
activated, see "

Virtual numeric keypad", Page 26

► Press the

Num

key.

82 Fujitsu Technology Solutions

Troubleshooting and tips

The notebook’s LCD screen remains blank

LCDscreenLCDscreenistoodark

Cause Troubleshooting

Monitor is switched off.

► Press a key or touch the touchpad.

External monitor or television s et connected. ► Press the key combination to switch the

screen outpu t, see "

Key combinations",

Page 27.

The LCD screen is difficult to read

LCDscreenLCDscreen

Cause Troubleshooting

Reflected glare ► Turn the notebook or alter the tilt of the LCD

screen.

► Increase the brightness of the screen.

The external monitor remains blank

Monitor

Cause Troubleshooting

Monitor is switched off. ► Switch the external monitor on.

Power saving has been activated (monitor is
blank).

► Press any key to continue.

Brightness is set to d ark.

► Adjust the brightness of the monitor.

Screen output is set to the notebook’s LCD
screen

► Press the key combination to switch the

screen outpu t, see "

Key combinations",

Page 27.

The externa l monitor’s power cable or data
cable is not connected properly.

► Switch off the e xternal monitor and the

notebook.

► Check whet

her the power cable is plugged

properly i

nto the external monitor and into

the power s

ocket.

► Check whether the data cable is properly

connected to the notebook and the external
monitor (if it is plugged in with a connector).

► Switch o

n the external monitor and the

noteboo

k.

Fujitsu Technology Solutions 83

Troubleshooting and tips

The external monitor is blank or

the image is unstable

ScreenMonitor

Cause Troubleshooting

The wrong external monitor h as

been selected

or the wrong screen resolution

has been set for

the application program.

► Terminate the application pro

gram in

Windows by pressing

Alt

+

F4

.Ifthe

fault persists after closing t

he progra m, use

the key combination for switc

hing the screen

output (see "

Key combinati

ons", Page 27)to

switch over to the notebook

’s LCD screen.

Change the following sett

ing:

► Set the screen resolution: Set the screen

resolution as described in the do cume ntation
foryouroperatingsystem.

► Select monitor: Select

monitor 1 or 2 as

described in the docume

ntation for your

operating system.

The notebook cannot be started

Notebook

Cause Troubleshooting

The battery is not installed correctly.

► Check whether the battery is installed

correctly in its compartment.

► Switch the notebook on.

The battery is dead.

► Charge the batte

ry.

or

► Insert a charged battery.

or

► Connect the mains adapter to the

notebook.

The power adapter is not connected correctly.

► Check whether the mains adapter is

connected correctly to the notebook.

► Switch the notebook on.

84 Fujitsu Technology Solutions

Troubleshooting and tips

The notebook stops w orking

NotebookEnergysavi ng mode

Cause Troubleshooting

Notebook is in energy saving mo

de.

► Leave energy saving mode.

An application programme has

caused the

malfunction.

► Close th e application program or restart

the notebook (by restarting the operating
system or switching the device off and back
on again).

The battery is dead.

► Charge the battery.

or

► Insert a charged battery.

or

► Connect the mains adapt

er to the

notebook.

The printer does not print

Printerdoesnotp

rint

Cause Troubleshooting

The printer is not switched on. ► Make sure that the printer is switched

on and ready for operation (refer to the
documentation supplied with the printer).

The printer is not connected correctly.

► Check that the d ata cable connecting

the notebook to the printer is properly
connected.

The printer driver is faulty or not correctly
installed, or it is the wrong printer driver.

► Check that the d ata cable connecting

the notebook to the printer is properly
connected.

► Check whethe

r the correct printer driver is

loaded (ref

er to the printer docum entation).

The radio connection to a network does n ot work

Theradi

oconnectiontoanetwo rkdoesnotwork

Cause Troubleshooting

The wireless component is disabled.

► Switch the radio component on (see

"

Switching the wireless components on and

off", Page 50).

The wireless component is enabled. Despite
this, the wireless connection to a network does
not work.

► Check whether the radio connection is

switched on via the software.

► Furthe

r information on using the radio

compo

nent can be found in the help files.

Fujitsu Technology Solutions 85

Troubleshooting and tips

Acoustic warnings

AcousticerrormessagesErrors

Cause

Troubleshooting

A beep sounds every few seconds.

The battery is alm ost flat.

► Charge the battery.

Error m essages on the screen

Errormessagesonthes c

reen

Errormessage:

This section describes the error messages generated by the BIOS Set up. Error messages displayed
by the operating system or programme s are described in the relevant documen tation.

If the error message appears repeatedly, despite troubleshooting measures, please
contact the place of purchase or our customer service centre.

Error message/cause Resolution

CMOS battery bad

If the error message occurs repeatedly, the
buffer battery in the notebook is flat.

► Contact your sales outlet or our customer

service centre.

System CMOS checksum bad - default configuration
used

The system configuration information is
incorrect.

► Switch the notebook off.
► Switch the notebook on.
► Press the function key

F2

to access the

BIOS Setup.

► In the BIOS Setup, select the Exit menu.
► Select the entry Load Setup Defaults.
► Select OK and p ress the Enter key.

Extended memory failed at offset: xxxx Failing Bits:
zzzz zzzz

When testing the extended memory an error has
resulted at the address xxxx.

► Check whethe

r the additional memory

module has be

en inserted correctly.

Failure Fixed Disk n

The settings of the hard disk drive are incorrect.

► Start the B

IOS Setup (Primary Master

submenu)

and select the correct settings.

Keyboard controller error

► Switch t

he notebook off w ith the ON/OFF

switch.

► Wait 3 - 5 seconds and switch on the

notebook again.

Keyboard error

If you are using an external keyboard:

► Check the connection and reboot the

notebook.

nn Stuck key

► Make sure that no key is pressed.

86 Fujitsu Technology Solutions

Troubleshooting and tips

Error message/cause Resolution

Operating system not found

► Check in the BIOS Setup whether y

our hard

disk has been set correctly.

► Make sure that the operating system is

installed on the corresponding drive.

Press <F1> to resume, <F2> to SETUP

This error message appears if an error occurs
during th e self-test before starting the operating
system.

► Press the

F1

function key to start the

operating system.

► Press the function key

F2

to access the

BIOS Setup.

Previous boot incomplete - Default configuration
used Due to an error during the previous system

boot, default values were used for certain
settings. Check the settings in the BIOS Setup.

► Press the

F1

function key when prompted

to do so.

Real time clock error

► Contact your sales outlet or our customer

service centre.

nnnnK Shadow RAM failed at offset: xxxx Failing
Bits: zzzz

► Contact your sales outlet or our customer

service centre.

System battery is dead - Replace and run SETUP

► Contact your sales outlet or our customer

service centre.

System cache error - Cache disabled

► Contact your sales outlet or our customer

service centre.

System timer error

► Contact your sales outlet or our customer

service centre.

Fujitsu Technology Solutions 87

Technical specifications

Technical specifications

Technicalspecifications

LIFEBOOK

Technicalspecifications

Ambient conditions

Operating temperature 5 °C–35 °C

Dimensions

Width x depth x height

321 mm x 228.5 mm x 24.2 – 32.3 mm (excl.
rubber feet)

Weight (including 6-cell rechargeable battery) Standard: approx. 1.9 kg

T&L: approx. 1.66 kg

Main memory

Slots 2 slots 204pin DDR3 SO-DIMM max. 16 GB

DDR3

Approved memory modules

max. 8 GByte DDR3 SO-D IMM per slot

The data sheet for the device provides further technica l data. You will find the data
sheet on your device or on the Internet under "

http://ts.fujitsu.com/support".

Port replicator (optional)

Electrical data

Safety regulations complied with CE, CB

Protection class II

Maximum power draw (with the n otebook
switched on and the battery charging)

Approx. 80 W

Dimensions/weight

Width x depth x height 360 mm x 110 mm x 30 mm

Weight Approx. 0.6 kg

Ambient conditions

Environment class DIN IEC 721

3K2

Mechanism class DIN IEC 721

7M2

Temperature:

Operation 5 °C ... 35 °C

Transportation

-15 °C ... 60 ℃

88 Fujitsu Technology Solutions

Technical specifications

Rechargeable battery

You will find further information about the batteries use d in your device on
the Internet under "

http://ts.fujitsu.com/support".

Rated voltage 10.8 V

Rated capacity 5200 mAh

Mains adapter

Technicalspecifications

Electrical data

Primary

Rated voltage

100 V – 240 V (automatic)

Rated frequency 50 Hz – 60 Hz (automatic)

Secondary

Rated voltage 19 V

Max. rated current 4.22 A

An additional mains adapter or power cable can be ordered at any time.

Fujitsu Technology Solutions 89

Manufacturer’s notes

Manufacturer’s notes

Energy Star

Products which are Energy Star certificated and labelled always meet the full
requirements of the standard when shipped. Please note that installation of
after-market hardware and software, changes to the BIOS or to the power
options may affect power consumption. The properties guaranteed by the
Energy Star label can then no longer be guaranteed.

Devices which are certified according to the Energy Star environmental
mark help to save money and reduce the emission of greenhou se gases.

Power Management settings on delivery:

• Monitor switched off after < 15 minutes of inactivity

• Automatic activati

on of energy saving mode (ACPI S3): < 30 minutes

of inactivity

Detailed information about the requirements of the "Energy Star"
environmental mark and the pro ducts which satisfy these requirements
can b e found on the Internet at "

https://www.energystar.gov/".

Disposal and recycling

Notes

Information about this subject can be found on your notebook or on our Internet pages.

Declarations of Conformity

Declaratio

nofconformity

The "Declarations of Conformity" for the device can be f ound at our Internet
address under: "

http://ts.fujitsu.com/ce".

Fujitsu Technology Solutions hereby declares that your device is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.

90 Fujitsu Technology Solutions

Manufacturer’s notes

CE marking

CEmarking

CE marking for devices with radio compo nent

This equipment complies with the requirements of Directive 1999/5/EC of the
European Parliament and Commission from 9 March, 1999 governing Radio
and Telecommunications Equipment and mutual recognition of conformity.

This equipment can be used in the following countries:

Belgium Bulgaria Denmark

Germany

Estonia Finland France

Greece

UK Ireland Iceland Italy

Latvia Liechtenstein Lithuania Luxembourg

Malta The

Netherlands

Norway Austria

Poland Portugal Rumania

Sweden

Switzerland Slovakia Slovenia Spain

Czech Repu blic

Hungary

Cyprus

Contact the corresponding government office in the respective country for
current information on possible operating restrictions. If your country is
not included in the list, then please contact the corresponding supervisory
authority as to whether the use of this product is permitted in your country.

Regulatory notices

If there is no FCC logo and also no FCC ID on the device then this device is
not approved by the Federal Communications Commission (FCC) of the USA.
Although it is not explicitly forbidden to travel in the US trading area carrying this
device, to avoid trouble at customs clearance, F ujitsu Techn ology Solutions GmbH
recommends not to bring this device into the US trading area.

Regulatory information for notebooks without radio device

Regulatoryinformation

NOTICE:

Changes or modifications not expressly approved by Fujitsu Technology Solutions
could void this user’s authority to o perate the equipment.

Notice to Users of Radios and Television

These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not insta lled and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between th e equipment and receiver.

Fujitsu Technology Solutions 91

Manufacturer’s notes

• Connect the equipment into an outlet that is on a different circuit than the receiver.

• Consult the dealer or an experienced radio/TV technician for help.

Notice to Users of the US Telephone Network

Your notebook may be supplied with an internal modem which complies with Part 68 of the
FCC rules. On this notebook is a label that contains the FCC Registration Number an d the
Ringer Equivalence Number (REN) for this equipment among other information. If re quested,
the user must provide their telephone company with the following information:

1. The telephone number to which the notebook is connected.

2. The Ringer Equivalence Number (REN) for this equipment.

3. The equipment requires a standa rd modular jack type USOC RJ-11C
which is FCC Part 68 compliant.

4. The FCC Registration Num ber.

This equipment is designed to be connected to the telephone network or pre m ises wiring using
a standard modular jack type USOC R J-11C which is FCC Part 68 compliant and a line cord
between the modem and the telephone network with a minimum of 26AWG.

The REN is used to determine the number of devices that you may connect to your telephone
line and still have all of those devices ring when your number is called. Too many devices
on one line may result in failure to ring in response to an incoming call. In most, but not all,
areas the sum of the RENs of all of the devices should not exceed five (5). To be certain
of the number of devices you may connect to your line, as determined by the RENs, contact
your local telephone company. If this equipment causes ha rm to the telephone network, your
telephone company may discontinue your service tem porarily. If possible, they will notify you
in advance. If advance notice is not practical they will no tify you as soon as possible. You
will also be advised of your right to file a complaint with the FCC.

This fax modem also complies with fax branding requirements per FCC Part 68.

Your telephone company will probably ask you to disconnect this equipment from the telephone
network until the problem is corrected and you are sure that the equipment is not malfunctioning.
This equipment may not be used on coin-operated telephones provided by your telephone
company. Connection to party lines is subject to state tariffs. Contact your state’s public utility
commission, public service commission or corporation commission for more informat ion.

This equipment includes automatic dialing capability. When programming and/or
making test calls to emergency numbers:

• Remain on the line and briefly explain to the dispatcher the reason for the call.

• Perform such activities in off-peak hours, such as early morning or late evening.

FCC rules prohibit the use of non-hearing aid compatible telephones in the
following locations or applications:

• All public or semi-public coin-operated or credit card telephones.

• Elevators, highways, tunnels (automobile, subway, railroad or pedestrian) where a
person with impaired hearing might be isolated in an emergency.

• Places where telephones are specifically installed to alert emergency authorities
such as fire, police or medical assistance p ersonnel.

• Hospital rooms, residential health care facilities, convalescent homes and prisons.

• Hotel, motel or apartment lobbies.

• Stores where telephones are used by patrons to order merchandise.

92 Fujitsu Technology Solutions

Manufacturer’s notes

• Public transportation terminals where telephones are used to call taxis or
to reserve lodging or rental cars.

• In hotel and motel rooms as at least ten percent of the rooms must contain hearing
aid-compatible telephones or jacks for plug-in hearing aid compatible telephones which
will be provided to hearing impaired customers on request.

DOC (Industry CANADA) notices

DOC(INDUSTRYCANADA)NOTICES

Notice to Users of Radios a

nd Television

This Class B digital appa

ratus meets all requirements of Canadian Interference-Causing Equipment

Regulations.

CET appareil numérique

de la class B respecte toutes les exigence du Réglement

sur le matérial brouill

eur du Canada.

Notice to Users of the

Canadian Telephone Network

NOTICE:

This equipment meet

s the a pplicable Industry Canada Terminal Equipment Technical

Specifications. Th

is is confirmed by the registration number. The abbreviation, IC, before

the registration n

umber signifies that registration was performed based on a Declaration of

Conformity indica

ting that Industry Cana da technical speci fications were met. It does not

imply that Indust

ry Canada approved the equipment. Before connecting this equipment to

a telephone line t

he user should ensure that it is permissible to connect this equipment to

the local teleco

mmunication facilities. The user should be aware that compliance with the

certification s

tandards does not prevent service degradation in some situations.

Repairs to tele

communication equipment should be made by a Canadian authorised

maintenance fa

cility. Any repairs or alterations not expressly approved by Fujitsu or

any equipment

failures may give the telecommunication company cause to request the

user to discon

nect the equipment from the telephone line.

NOTICE:

The Ringer E

quivalence Number (REN) for this terminal equipment is 0.0. The REN assigned

to each term

inal equipment provides an indication of the maximum numb er of terminals

allowed to b

e connected to a telephone interface. The termination on an interface may

consist of

any combination of devices subject only to the requirement that th e sum of the

Ringer Equ

ivalence Numbers of all the devices does not exceed five.

CAUTION:

For safet

y, users s hould ensure that the electrical ground of the power utility, the

telepho

ne lines and the metallic water pipes are connected together. Users should NOT

attempt

to make such connections themselves but should contact the appropriate electric

inspec

tion a uthority or electrician. This may be particularly important in rural areas.

Avis Aux Utilisateurs Du Réseau Téléphonique Canadien

AVIS : Le présent matériel est conforme aux spécifications techniques d’Industrie Canada
applicables a u matériel terminal. Ce tte conformité est confirmée par le numéro d’enregistrement.
Le sigle IC, placé devant le numéro d’enregistrement, signifie que l’enregistrement s’est effectué
conformément à une déclaration de conformité et indique que les spécifications techniques
d’Industrie Canada ont été respectées. Il n’implique pas qu’Industrie Canada a approuvé le matériel.

Fujitsu Technology Solutions 93

Manufacturer’s notes

Avant de connecter cet équipement à une ligne téléphonique, l’utilisateur doit vérifier
s’il est permis de connecter cet équipement aux installations de télécommunications
locales. L’utilisateur est averti que même la conformité aux normes de certification ne
peut dans certains cas empêcher la dégradation du service.

Les réparations de l’équipement de télécommunications doivent être effectuées par un service de
maintenance agréé au Canada. Toute réparation ou mod ification, qui n’est pas expressément
approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de
télécommunications à exiger que l’utilisateur déconnecte l’équipement de la ligne téléphonique.

AVIS : L’indice d’équivalence de la sonnerie (IES) du présent matériel est de 0.0. L’IES
assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent
être raccordés à une interface téléphonique. La terminaison d’une interface peut consister
en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices
d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.

AVERTISSEMENT:

Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise de terre du service
d’électricité, les lignes télphoniques et les conduites d’eau métalliques sont connectées
ensemble. Les utilisateurs NE doivent PAS tenter d’établir ces connexions eux-mêmes,
mais doivent contacter les services d’inspection d’installations électriques appropriés
ou un électricien. Ceci peut être particulièrement important en régions rurales.

UL Notice

This unit requir

es an AC adapte r to operate. Only use a UL Listed Class 2 adapter.

The correct out

put rating is indicated on the AC adapter label. Refer to the illustration

below for the co

rrect AC Adapter output polarity:

CAUTION:

To reduce the risk of fire, use only 26AWG or larger telecommunications line cord.

For A ut horized Repair Technicians Only

CAUTION:

For continued protection against risk of fire, replace only with the
same type and rating fuse.

WARNING:

Danger of explosion if Lithium (CMOS) battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

94 Fujitsu Technology Solutions

Manufacturer’s notes

FCC regulatory information for notebooks with radio device

Regulatoryinformation

Federal Communica tio ns Commission statement

This device complies with Part 15 of FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may
cause undesired operation of this device.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy. If not installed and used in accordance w ith
the instructions, it may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the distance between the equipment and the receiver.

3. Connect the equipment to an outlet on a circuit different from the one the receiver is connected to.

4. Consult the dealer or an experienced radio/TV technician for help.

Please note the following regulatory information related to the optional radio device.

FCC Radio Frequency Exposure statement

This radio device has been evaluated u nder FC C Bulletin OET 65C and found compliant with the
requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF
Exposure from radio frequency devices. The radiated output power of this radio device is far below
the FCC radio frequency exposure limits. Nevert heless, this device shall be used in such a manner
that the potential for human contact during normal operation is minimized. When using this device, a
certain separation distance between antenna and nearby persons must be maintained to ensure RF
exposure compliance. In order to comply with RF e xposure limits esta blished in the ANSI C95.1
standards, the distance between the antennas and the user should not be less than 20 cm (8 inches).

Regulatory Notes and Statements
Radio device, health and authorisation for use

Radio-frequency electromagnetic energy is emitted from the wireless devices. The energy levels
of these emissions, however, are far much less than the electrom agnetic energy emissions from
wireless devices such as mobile phones. Radio devices are safe for use by consumers because
they operate within the guidelines found in radio frequency safety stand ards and recommendations.

The use of the radio devices may be restricted in some situations or environments, such as:

• on board an airplane, or

• in an explosive environment, or

• in situations where the interference risk to o ther devices or services is
perceived or identified as harmful.

In cases in which the policy regarding use of radio devices in specific environments is not
clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain
authorization to use these devices prior to operating the equipment.

Fujitsu Technology Solutions 95

Manufacturer’s notes

Regulatory Information/Disclaimers

Installation and use of this radio device must be in strict accordance with the instructions included
in the user documentation provided with the product. Any changes or modific ations made to this
device that are not expressly approved by the manufacturer may void the user’s authority to operate
the equipmen t. The manufact urer is not responsible for any radio or television interference caused
by unau thorized modification of this device, or the substitution or attachment of co nnecting cables
and equipment other than those specified by the manufactu rer. It is the responsibility of the user
to correct any interference caused by such unauthorized modification, substitution or attachment.
The manufacturer and its authorized resellers or distributors will assume no liability for any dama ge
or violation of government regulations arising from failure to comply with these guidelin es.

Export restrictions

This product or software contains encryption code which may not be exported or
transferred from the US or Canada without an approved US Department of Commerce
export license. This device complies with Part 15 of FCC Rules, as well as ICES 003 B
/ NMB 003 B. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference
that may cause undesirable operation.

Modifications not expressly authorised by Fujitsu Technology Solutions may
invalidate the user’s right to operate this equipment.

96 Fujitsu Technology Solutions