Fujitsu LifeBook S4532 User's Guide

Copyright

Fujitsu Limited has made every effort to ensure the accuracy and completeness of this document. However, as
ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the
accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes.

LifeBook is a trademark of Fujitsu Limited.
Microsoft, Windows, MS, MS-DOS , and Windows NT are registered tr ademarks of the Microsoft Corporation of the
United States in the United States and other countries.
Intel is a registered trademark of the Intel Corporation of the United States.
Celeron is a trademark of the Intel Corporation of the United States.
NeoMagic MagicMedia 256AV and NeoMagic MagicMedia 256AV+AC97 Driver (WDM) are trademarks of
NeoMagic™ Corporation.
Puma Technology, Intellisync is a trademark of Puma Technology Corporation of the United States.
Phoenix is a registered trademark of Phoenix Technologies Corporation of the United States.
K56flex is a trademark of Rockwell International Corporation and Lucent Technologies Corporation.
Magic Packet is a registered trademark of Advanced Micro Devices, Inc.
Other product names are trademarks or registered trademarks of their respective companies.
Other products are copyrighted by their companies.

Copyright© 1981-1999 Microsoft Corporation, All rights reserved.
Copyright© 1999 Phoenix Technologies, Ltd., All rights reserved.

All other products are trademarks or registered trademarks of their respective companies.
Explanations of the adjustments for the track pad cursor control are taken in part from the ALPS GlidePoint Driver

User’s Guide, copyright by LCS/Telegraphics in 1996.
© Copyright 2000 Fujitsu Limited. All rights reserved. No part of this publication may be copied, reproduced, or

translated, without the prior written consent of Fujitsu Limited. No part of this publication may be stored or transmit­ted in any electronic form without the written consent of Fujitsu Limited.

DECLARATION OF CONFORMITY

according to FCC Part 15

Responsible Party Name : FPCA

Declares that product: Model : LifeBook S-4530 or S-4532

Address : Fujitsu PC (Asia) Pte Ltd

200 Pandan Loop
#05-03, Pantech 21
The Computer Centre

Singapore 128388

Telephone : [phone]

This device complies with Part 15 of the FCC Rules. Operations are subject to the following two conditions:
(1) This device must not be allowed to cause harmful interference, (2) This device must accept any interference
received, including interference that may cause undesired operation.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions carefully. Save these instructions for future reference.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.

4. Do not use this product near water.

5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious
damage to the product.

6. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliab le
operation of the product and to protect it from overheating, these openings must not be blocked or
covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should nev er be placed near or over a r adiator or heat register , or in a built­in installation unless proper ventilation is provided.

7. This product should be operated from the type of power indicated on the marking label. If you are not
sure of the type of power available, consult your dealer or local power company.

8. This product is equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This
will only plug into a grounding-type power outlet. This is a safety feature. If you are unable to insert the
plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose
of the grounding-type plug.

9. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on
the cord.

10. If an extension cord is used with this product, make sure that the total ampere rating of the equipment
plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure
that the total rating of all products plugged into the wall outlet does not exceed 15 amperes.

11. Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points that could result in a fire or electric shock. Never spill liquid of any kind on the product.

12. Do not attempt to service this product yourself, as opening or removing covers may expose you to
dangerous voltage points or other risks. Refer all servicing to qualified service personnel.

13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:

a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally when the operating instr uctions are followed. Adjust

only those controls that are covered by the operating instructions since improper adjustment of
other controls may result in damage and will often require extensive work by a qualified tech-

nician to restore the product to normal condition.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in performance, indicating a need for service.

14. CAUTION. When replacing the battery, be sure to install it with the polarities in the correct posi-

tion. There is a danger of explosion if the battery is replaced with an incorrect type or is mis­treated. Do not recharge, disassemble or dispose of in fire. Replace only with the same or equiva­lent type recommeded by the manufacturer . Dispose of the used battery accor ding to the manu­facturer’s instructions.

15. Use only the proper type of power supply cord set (provided in your accessories box) for this unit. It
should be a detachable type: UL listed/CSA certified, BS1363,ASTA,SS145 certified, rated 10A 250V
minimum, VDE approved or its equivalent. Maximum length is 15 feet (4.6 meters).

NOTATION IN THIS DOCUMENT

Warnings

This manual uses a variety of icons as visual marks so that you can use this computer safely and
correctly and avoid damage and danger to yourself and to others . These icons and their meanings
are as follows. Please learn these icons before reading this man ual. Learning these icons will be
useful for understanding this manual.

Icon Meaning

WARNING
CAUTION

The symbols below are used together with the icons above to indicate what type of danger or
damage is involved.

Symbol Meaning

Incorrect handling or ignoring this warning can cause a dangerous
situation that could result in death or severe injury.

Incorrect handling or ignoring this warning can cause a dangerous
situation that could result in moderate or minor injury or could result in
equipment damage.

The D symbol indicates a warning or caution. The symbol inside the D
indicates the concrete nature of the warning. (The example on the left
is a caution for electric shock.)

The circle and slash indicates prohibited behavior. The symbol inside
the circle indicates the concrete nature of the prohibition. (The
example on the left indicates that disassembly is prohibited.)

indicates instructions that must be followed. The symbol inside

The
indicates the concrete nature of those instructions. (The example on
the left tells you to unplug the power plug from the socket.)

Key notation and operation methods

Explanations of key operations do not show all the characters on the keyboard. Instead they
indicate just the keys necessary to the explanation as follows.
Examples: [Ctrl] key, [Enter] key, [ fi ] key
When multiple keys are to be pressed at the same time, this is indicated b y connecting them with
[+].
Examples: [Ctrl] + [F3] keys; [Shift] + [ › ] key

Screen examples

The screens shown in this manual are examples. Please understand that the file names and
screens you use may be different.

Notation in text

Here is what symbols in text mean.

Symbol Meaning

Critical Points

Indicates a point necessary for correctly operating the hardware or
software.

Gives the meaning and brief explaination of a term.

Column

fi Indicates the page to see elsewhere in this manual.

Command input (key input)

Within the text of this manual, command input (giving commands to the computer by pressing
keys) is indicated as follows.

Example:

In the position indicated in the example above by the ›, the space left between the characters
indicates that a space needs to be left in the entry by pressing the space bar (the long key with
nothing written on it at the center of the front of the keyboard). Commands are written in this
manual as lowercase latin letters, but uppercase letters may be used.

Product names

The following product names are abbreviated as follows in this manual.
“Microsoft

“Microsoft® MS-DOS® operating system Version 6.2/V” is written as “MS-DOS”.
“Microsoft® Windows® operating system Version 3.1” is written as “Windows 3.1”.
“Microsoft® Windows NT® Server network operating system V ersion 3.5” and “Microsoft® Windows
NT® Workstation operating system Version 3.5” are both written as “Windows NT 3.5”.
“Microsoft® Windows NT® Server network operating system V ersion 3.51” and “Microsoft® Windows
NT® Workstation and NT Server Version 4.0” are both written as “Windows NT 4.0”.
“Windows NT 3.51” and “Windows NT 4.0” are both written as Windows NT.
“Fujitsu Lifebook” is written as “this computer” or “the computer main unit”.

dir c:

›

®

Windows® 98 operating system” is written as “Windows 98”.

Configuration of this Manual

SECTION 1

This section explains basic operations and basic items for using this computer, including the
names of the parts and their functions, quick point IV operation methods, connector box han­dling, and battery operation.

SECTION 2

This section explains installation of options for this computer.

SECTION 3

This section explains the BIOS setup program, which is necessary for setting the date and time
and power conservation mode. This section also explains how to set the pass word f or protecting
data in this computer.

SECTION 4

This section explains what to do when trouble occurs with this computer and when messages are
displayed. Read this section as the necessity arises.

SECTION 1

SECTION 2SECTION 3

SECTION 4

CONTENTS

SECTION 1

1. Names of the Parts and their Functions .............................2

Front/Top .............................................................................................2

Left Side/Right Side.............................................................................4

Rear/Bottom ........................................................................................ 6

Port replicator ......................................................................................8

Status Indicator LCD ........................................................................... 9

2. Flat Point ..............................................................................11

What Is the Flat Point? ......................................................................11

Flat Point Usage ................................................................................ 12

3. Keyboard ..............................................................................13

Keyboard ...........................................................................................13

Numeric Keypad Mode...................................................................... 13

Names of the Main Keys and their Functions.................................... 14

4. Switching on the Power ......................................................16

Switching on the power ..................................................................... 16

5. Switching off the Power......................................................18

Precautions for Switching Off the Power ........................................... 18

Switching Off the Power ....................................................................18

6. Suspend/Resume Function ................................................20

Suspending ....................................................................................... 20

What Is the Suspend/Resume Function? .......................................... 20

Precautions for Suspending .............................................................. 22

Resuming .......................................................................................... 23

7. Battery ..................................................................................24

Battery Charging ............................................................................... 24

Battery Operation .............................................................................. 25

Checking the Remaining Battery Charge ..........................................26

Low Battery State ..............................................................................27

Replacing the Internal Battery Pack ..................................................28

Precautions for Battery Pack............................................................. 30

8. Port Replicator.....................................................................31

Attaching the port replicator .............................................................. 31

Detaching the port replicator ............................................................. 32

9. Built-in LAN (local-area network) device...........................33

Connection ........................................................................................ 33

10.Internal FAX Modem............................................................34

Connection ........................................................................................ 34

SECTION 2

1. Options .................................................................................36

What is the Options ...........................................................................36

2. PC Cards ..............................................................................38

Precautions for PC Cards.................................................................. 38

Installing PC Cards............................................................................ 39

Removing PC Cards.......................................................................... 40

3. Expansion RAM Modules ...................................................42

Installing an Expansion RAM Module................................................ 42

Removing an Expansion RAM Module.............................................. 44

4. Multi-bay Unit.......................................................................45

Replacing multi-bay units .................................................................. 45

Precautions on handling or using the multi-bay unit.......................... 46

Loading/Ejecting disks....................................................................... 47

Loading/Ejecting an LS-120 disk ....................................................... 49

5. Floppy Disk Unit ..................................................................50

Installing a Floppy Disk Unit ..............................................................50

Precautions for Floppy Disk Unit .......................................................51

Removing a Floppy Disk Unit ............................................................52

What is a Floppy Disk?...................................................................... 53

Precautions on Handling ................................................................... 54

Loading/Ejecting a Floppy Disk .........................................................55

Loading.............................................................................................. 55

Ejecting.............................................................................................. 55

6. Mouse ...................................................................................56

Using the Mouse ............................................................................... 56

Connecting the Mouse ...................................................................... 56

7. Numeric Keypad ..................................................................58

Connecting a Numeric Keypad.......................................................... 58

8. CRT Monitor .........................................................................59

Connecting an External CRT Monitor................................................ 59

9. CCD Camera ........................................................................61

Preparing required things ..................................................................62

Connecting the CCD camera ............................................................ 62

Using CCD camera ........................................................................... 62

Removing the CCD camera from personal computer........................ 65

10.One Touch Operation buttons ............................................66

SECTION 3

SECTION 4

1. BIOS setup ...........................................................................68

2. POST Diagnostic Screen ....................................................95

1. When This Happens ............................................................98

SECTIONSECTION

SECTION

SECTIONSECTION

SECTIONSECTION

SECTION

SECTIONSECTION

11

1

11

11

1

11

SECTION 1

SECTION 1

1.

Names of the Parts and their Functions

Front/Top

1

2

3

4

5

6
7

8

9

1 LCD panel

Displays text, graphics, etc.

Critical Point

The TFT color LCD panel used with this computer has been made using high resolution
technology, but there might be dots that are always lit up or always not lit up on part of the
screen.
There may be some slight inconsistencies on the LCD panel with variations in temperature.
Please note that this is not a malfunction.

2 Cover close switch

When the LCD panel is closed, this switch turns off the backlight and suspends operation of the
personal computer.

3 Suspend/Resume switch

This switch suspends/resumes the computer main unit. From here on, it is written as SUS/RES
switch.

2

10

4 Condenser Microphone

Allows sound (monaural) recording.

Critical Point

When some kind of software (karaoke software, etc.) is activ ated, it automatically inactiv ates
muting of the built-in microphone and the built-in speaker may resultingly howl. In such the
case, use a general headphone and external speaker available on the market.
When the built-in microphone is used, be sure to hold the LCD panel open, otherwise howling
may be occur.

5 One-touch button

Allows you to start application software or check the arrival of an e-mail.

6 LCD

Displays the status of the computer main unit. See “Status Indicator LCD”.

7 Keyboard

Keys are pressed to give commands to the computer main unit.

8 Speaker

Outputs the sound of the computer main unit.

Critical Point

If the built-in speaker and microphone are used at the same time, it may cause howling. If
howling occurs, adjust the sound volume with the volume control knob and “V olume Control”
on the screen.

9 Flat point

This moves the mouse pointer.

! Latch

This is pressed to release the lock when the LCD panel is opened.

SECTION 1

3

Left Side/Right Side

1211 13

14 15 16 17 18 19 20

" Multi-bay

Depending on the models, one of the following units is provided for your personal computer.

• CD-ROM drive unit

• CD-R/RW drive unit

• CCD Camera drive unit

• DVD-ROM drive unit

• Super disk drive unit

• PC card drive unit

• Weight saver

Critical Point

Do not leave the multi-bay v acant when using y our computer , otherwise y our computer might
break down.

# Multi-bay unit release lever

Raise this lever to remove the unit from the multi-bay.

$ Anti-theft lock

Can be connected with a commercially available anti-theft cable.

Critical Point

The anti-theft lock is for the Kensington Microsaver Security System.

% Headphone jack

For connecting commercially available headphones.

Critical Point

Things that can be fitted to the headphone jack

- Headphones, earphones, amplifier-installed external speakers (mini-plug with 3.5mm outer
diameter. However you may not be able to fit them because of the shape, so check before
inserting.)

4

& Line In jack

Terminal for audio input.

( Microphone jack (MIC-IN jack)

Terminal for connecting a commercially-available microphone.

Critical Point

When a microphone is in use, excessively turning up the volume might cause the speaker to
howl.
Some types of commercially-available microphones (for example, dynamic microphones)
cannot be used with this computer.

) Volume control

Adjusts the sound volume. Turning it towards you lowers the volume; turning it away from you
raises it.

Critical Point

If the volume is raised too high when using a microphone, howling may occur between the
speaker and the microphone.

~ PC card eject/lock button

Press this button to eject the PC card. When the inserted PC card is locked by this button, it is
protected from accidentally sticking out.

+ PC card slot

Slot (1) for inserting separately sold PC card.
This PC card slot is identified as ZV port, which is connected with the main unit of this personal
computer.

Critical Point

A dummy card has been inserted in the PC card slot of a new computer.
The ZV port conforms to the PC card standard for high-speed processing of animation and
sound data.
You may be required to use the “slot 0” for “slot 1” depending on the operating system used.

SECTION 1

, Modular connector

This is for connecting to the telephone line.

5

Rear/Bottom

21

22
23

24

25

26

27

28

29

30

31

32

6

- Infrared communications port

Interface for carrying out infrared communications.

Critical Point

Don’t bring the AC adaptor or CRT display close to the infrared communications port during
infrared communication, otherwise the computer may malfunction because of noise generated.

. mini-Serial connector (available on certain model)
/ USB connector (Invalid for the Windows NT system)

Connector for connecting a peripheral equipment which meets the USB standard.

: LAN connector

Connector for connecting a LAN cable.

; CRT connector

Connector for connecting an external display, for example, a separately sold CRT monitor.

< DC-IN connector

Connector for connecting the AC adaptor that comes with this computer.

= MAIN switch

This is the switch for turning the power to the computer main unit on and off.

> Port replicator connector

Connector for connecting the port replicator.

? Expansion RAM module slot

Slot for fitting a separately sold expansion RAM module.

@ Release button

Slide this release button to release the internal battery pack lock from locking status.

[ Internal battery pack lock

Slide this lock to attach/detach the internal battery pack to/from this personal computer.

\ Internal battery pack

The internal battery pack is mounted here.

SECTION 1

7

Port replicator

1

52 3 4 6 8 9 107

1 Port replicator release button

Slide this button to remove the port replicater
from the personal computer.

2 LAN connector

Connector for connecting a LAN cable.

3 Expansion keyboard connector

Connector for connecting a separately sold PS/2 standard numeric keypad.

4 Mouse connector

Connector for connecting a separately sold PS/2 mouse.

5 USB connector (Invalid for the Windows NT system)

Connector for connecting a peripheral equipment which meets the USB standard.

6 CRT connector

Connector for connecting a separately sold CRT monitor.

7 Parallel connector

Connector for connecting a separately sold printer.

8 Serial connector

Connector for connecting an optional equipment of the RS-232C interface standard.

9 FDD unit connector

Connector for connecting a separately sold floppy disk unit.

Mouse connector

Connector for connecting a separately sold PS/2 mouse.

! DC-IN connector

Connector for connecting the AC adaptor that comes with this computer.

" Connector

Connector for connecting the port replicater.

11

8

Status Indicator LCD

1

2

SECTION 1

1

2

1

A

1 2 11 12

5

3

8 9 1076

1 SUS/RES indicator ( )

When this computer is operating, this indicator lights up; when the computer is in suspend mode,
this indicator flashes.

2 AC adaptor indicator ( )

Lights up when the power is being supplied from the AC adaptor.

3 Battery pack mounting indicators ( 1, 2, )

Lights up when the battery pack is mounted. The number 1 ref ers to the b uilt-in battery pack and
the number 2 refers to the expanded battery pack.

4 Battery charging indicator ( )

Lights up when the battery is charging; flashes when the battery is too hot or cold to charge.

5 Remaining battery charge indicator ( )

Displays the amount of charge remaining in the corresponding battery.

6 CD-ROM drive access indicator ( )

Lights up while data is being read from the CD-ROM or the DVD-ROM.

7 Hard disk access indicator ( )

Lights up while the internal hard disk or the 2nd hard disk is being accessed.

8 Floppy disk access indicator ( )

Lights up while data is being read/written on the floppy disk or the LS-120 disk.

9 PC card access indicator (

Lights up while the PC card in the corresponding PC card slot is being accessed.
The indicator 1 corresponds to the built-in PC card slot, while the indicator 2 corresponds to the

PC card drive unit mounted in the multi-bay.

1 2

)

9

! Num Lock indicator (

Lights up when [Num Lk] key is pressed to put the keyboard into numeric keypad mode.

" Caps Lock indicator (

Lights up when [Shift] + [Caps lock] keys are pressed to put the keyboard into CAPS mode.

)

1

)

A

# Scroll Lock indicator ( )

Lights up or goes out each time the [Fn] + [Scr Lk] keys are pressed.

Critical Point

If you turn off the main switch or operate the SUS/RES button while the hard disk access
indicator or floppy disk access indicator is lit, the data being accessed may be destroyed.
When the main switch is switched off, all the indicators other than charging go off. However,
the AC adaptor lamp comes on regardless of the status indicator lamp when power is being
supplied.
When you use Windows 98, if the CD automatic insertion function is enabled, the system
periodically checks for a CD. Therefore, the CD-ROM drive access indicator on the status
indicator LCD lights up periodically.

10

SECTION 1

2. Flat Point

What Is the Flat Point?

The main operations for this computer use the flat point. This item explains the flat point.
The flat point is a convenient pointing device that moves the mouse pointer with your fingertips. It
comprises the operating surface and the two buttons in front of it. The operating surface has the
same function as the ball section of a mouse. Y ou mo v e the mouse pointer on the screen by mo ving
your fingertip up, down, left, and right along the operating surface. You can also carry out such
operations as clicking, double clicking, pointing, and dragging by tapping lightly on the operating
surface. The left and right buttons correspond to the b uttons the mouse. Their functions depend on
the application software.

Operating surface

SECTION 1

Left button

Right button

Critical Point

There is a slight difference in a result of pointing operation among operators because of the
operation principle of the flat point. Given an example, pointing operation is influenced by
moisture of the operator’ s fingertips (dry or wet fingers).
If the operating surface is dirty or moist because of high humidity , etc., it may cause malfunction
of the operating surface. If it occurs, wipe down the operating surface with dry soft cloth to
remove the moisture and dirt. If the operating surf ace is badly soiled, wipe out the dirt with soft
cloth moistened with a neutral detergent thinned with water.
When you intend to use an optional mouse, access the “Keyboard/Mouse Setting” menu of
the “BIOS Setup” and set items necessary for operating the mouse together with the flat point.

11

Flat Point Usage

Click Either tap the operating surface once or press the

Double click Either tap the operating surface twice consecu-

Point Align the mouse pointer with a menu item or the

Drag Move the mouse pointer to any position, then

left button once until it clicks, then immediately
release it. Clicking the right b utton once is called
a right click.

tively or twice quickly press the left button twice
until it clicks, then immediately release it.

like. If there is a level beneath the manual item
on which you placed the mouse pointer (if > is
displayed at the right end of the menu item), that
menu is displayed.

quickly tap the operating surface twice. After the
second tap, do not remove y our fingertip from the
operating surface, b ut drag it along the operating
surface to the desired position, then remove y our
finger from the operating surface.

Critical Point

You can also carry out the click and drag operations in combination with the buttons.
Tap gently and quickly with your fingertips. There is no need for much force.
When you are moving the mouse pointer with the flat point, if you lift up your fingertip and
bring it back down to a different point on the operating surface, the mouse pointer on the
screen does not move. If you dr ag your fingertip along the operating surface from the position
where you brought it back down, the mouse pointer on the screen moves in the direction in
which you drag your fingertip.
The interval between taps for double clicking can be adjusted with Mouse in the Control P anel
for Windows 98.

12

SECTION 1

3. Keyboard

Keyboard

The keyboard is the device f or giving instructions to the computer , inputting data, and ex ecuting. The
keys can be divided into two types.

Control keys
Character keys

SECTION 1

Numeric Keypad Mode

The mode in which some of the character keys are used as numeric keys (with a key layout that
makes numeric input easier) instead of their normal functions is called numeric keypad mode. The
keyboard is switched to numeric keypad mode with [Num Lk]. (In numeric keypad mode,
played on the status indicator LCD.) The keys surrounded by thick lines in the diagram above be­come the numeric keypad. The numbers input with these keys are printed in front of each key.

is dis-

1

Critical Point

When the separately sold numeric keypad is connected, if you press [Num Lk] to put the
computer into numeric keypad mode, the keys on the external numeric keypad are enabled,
but the numeric keypad section on the keyboard is disabled.

13

Names of the Main Keys and their Functions

Esc (escape) key

The usage is determined by the application software. It is often used to return to the previous
operation.

F1-F12 (function) keys

The usage depends on the application software.

Fn key

A key unique to this computer; it has the following functions.

[Fn] + [F3] This switches ON/OFF of the speaker.

[Fn] + [F5] This selects whether or not to use the entire LCD screen for display in text
[Fn] + [F6] Turns down the backlight of the LCD.

[Fn] + [F7] Turns up the backlight of the LCD.

Critical Point

Luminance of the backlight of the LCD can be turned up (with [Fn] + [F7] keys) or turned
down (with [Fn] + [F6] keys) in three degrees.

When a pip sounds with this operation, the speaker is on. When nothing
sounds, the speaker is turned off.

mode.

[Fn] + [F10] Rotates among the three display options: LCD only, CRT only, both LCD

[Fn]+SUS/RES switch

Space key Inputs a single space character.

[›][fl][‹][fi] (cursor) keys

and CRT.

Activates the Save To Disk function.

(This is the long key with nothing written on it at the center of the front of the
keyboard.)

Move the cursor.

14

Enter key

Also called the return key or the line feed ke y . This key inputs line f eeds and ex ecutes command.

Ctrl key

Used in combination with other keys; its functions depend on the application software.

Shift key

Used in combination with other keys.

Alt key

Used in combination with other keys; its functions depend on the application software.

Caps Lock key

T o loc k the ke yboard into caps mode, press this k ey together with the Shift k e y. Pressing this
key again ends caps mode.

Num Lk (numerical lock) key

Press this key to put the computer into numeric keypad mode.

Scr Lk (scroll lock) key

Its functions depend on the application software.

Print Screen key

Press this key to make a hard copy of the screen.

Pause key

Press this key to pause the screen display.

Break key

Its functions depend on the application software.

Insert key

Press this key to insert a new character between characters. The new characters are entered
at the cursor position.

Delete key

Press this key to delete a character . Pressing the Delete key and the Ctrl and Alt keys at the
same time resets this computer.

Home key

Press this key to move the cursor directly to the head of the ro w or the head of the document.

End key

Press this key to move the cursor directly to the end of the row or the end of the document.

Pg Up key

Press this key to switch to the previous screen.

Pg Dn key

Press this key to switch to the next screen.

Back Space key

Press this key to delete the character to the left of the cursor position.

Sys Rq (system request) key

When this key is supported by the application software, this key is used f or such functions as
resetting the keyboard. Press this key together with the Alt key.

[ ] (Windows) key (only valid for Windows 98)

Press this key to display the Start menu.

[ ] (Application) key (only valid for Windows 98)

Press this key to display the shortcut menu for the selected item. This key has the same role
as the mouse right click.

SECTION 1

15

SECTION 1

4. Switching on the Power

Switching on the power

This item explains the normal way to switch the computer main unit power on.

Critical Point

When turning on the personal computer connected with an optional FDD unit, check to see
whether a floppy disk is set in the floppy disk drive or not. If there is a floppy disk set in the
drive, be sure to remove it before turning on the computer.

1 Connect the AC adaptor.

2

3

1

AC adaptor

First connect the AC power cord to the AC
adaptor (1), next connect the other cord of
the AC adaptor to the personal computer’ s DC­IN connector (2). Lastly, plug the AC power
cord into an AC outlet (3).

3 Switch on the main switch of the

computer main unit.

2 Open the LCD panel.

Latch

Push the latch to release the lock, then lift the
display panel with your hand.

Main switch

Power is supplied from the AC adaptor, the
power comes on, and the POST starts. Also ,
the

etc. on the status indicator LCD are

displayed.

16

Critical Point

Do not carry this computer around or subject it to shock or vibration with the power on. These
can result in breakdown.

Column

POST is the abbreviation for POWER ON SELF TEST, which is a self-diagnostic test that
checks for abnormalities within the computer. This test is automatically carried out when the
power is switched on for this computer . If the pow er is switched off during the POST, an error
message is displayed the next time the computer is started up. Do not cut off the power
during the POST.

SECTION 1

17

SECTION 1

5. Switching off the Power

This item explains how to switch off the power and gives precautions for switching off the
power.

Precautions for Switching Off the Power

The following precautions must be observed when switching off the power.

When switching off the main switch, end Windows 98 first.
When the main switch is switched off, if the suspend mode is suspend, the suspend function

stops working. If the application software has been suspended during e xecution, it is necessary
to save the data, then end the application software.

After you switch off the main switch, wait at least about ten seconds before switching it back
on again.

Switching Off the Power

1 Click the Start button.

The Start menu is displayed.

2 Click Shut Down.

The following message is displayed.

18

3 Check that Shut down the computer is selected, then click Yes.

The power is switched off.

Critical Point

If the MAIN switch is not turned off after the step 3, the computer will be turned on next time
by pressing the SUS/RES switch only.
You can reset this computer by selecting Restart the computer with the screen shown in Step

2. Resetting means that the data in memory is all erased and the operating system is loaded
again from the hard disk or a floppy disk.

SECTION 1

4 Switch off the main switch.

Slide the main switch in the direction of the
arrow (
indicator goes out and the power for the
computer main unit is cut off.

side). The status indication LCD

Critical Point

If the computer will be unused for a long period, remove any CD-ROM or floppy disk and
disconnect the AC adaptor.

Main switch

19

SECTION 1

6. Suspend/Resume Function

What Is the Suspend/Resume Function?

When this computer is suspended with the SUS/RES switch, the suspend/resume function retains
the programs and data in memory as is so that you can resume operations immediately the next time
you press the SUS/RES switch.

Critical Point

Which of the two destinations suspending saves the data in the computer to depends on the
BIOS setup Power menu setting as follows.

System RAM:

When “Suspend” is set with the BIOS setup Power menu Suspend Mode item, the
data is saved to system RAM. Power for the system RAM is supplied from the AC
power supply if the AC adaptor is connected or from the battery if the AC adaptor is
not connected.

Save to Disk area:

If “Save to Disk” is set with the BIOS setup Power menu Suspend Mode item, the data

is written to the Save to Disk area on the hard disk.
If you hold down the Fn key while pressing the SUS/RES s witch, the data is sav ed to the hard
disk regardless of the Power menu setting.

Suspending

There are three ways to suspend this computer , using the SUS/RES switch, Cover close switch and
for Windows 98, using the Start menu.

Using the SUS/RES switch

1 Suspending

Check that and are out. When you
press the SUS/RES switch, if the BIOS setup
suspend mode is suspend,
the computer goes into suspend mode.

flashes and

SUS/RES switch

20

Using the cover close switch
1 Close the LCD panel.

This unit goes into suspend mode using

the cover close switch.

Critical Point

When the BIOS setup Lid Closure Suspend setting is “Disabled”, this unit does not go into
suspend mode even if you close the LCD panel.

Use the [Quit Windows] dialog.
1 Click the [START] button and then click the [Quit Windows].

The [Quit Windows] dialog appears on the display.

2 Click Standby.

This computer is suspended.

Critical Point

The computer may not be suspended in the following cases.

• When the operating system is activated.

• When any of device drivers is incorrectly installed.
It takes a considerable time to suspend the computer depending on its operating condition.
If the BIOS setup Suspend Mode setting is “Suspend”, suspend mode is ended in the following
cases. Save important data to a floppy disk or the hard disk.

• The main switch is switched off.

• In battery operation, the battery runs out.
(The battery is still used in suspend mode.)

If you start with the internal battery fully charged, suspend mode lasts about three days
maximum with the AC adaptor not connected.

• When “Use” is selected for “Resume b y modem incoming” on the “P ower Savings” menu of
the BIOS setup.

• When “Restore the computer to the original status with a telephone call” is effectively set
by the tab of “Others” of the Windows 98 “PMSet98 properties” window.

SECTION 1

21

Precautions for Suspending

Pay attention to the following points when using the suspend function.

Don’t continue pressing the SUS/RES switch for 4 seconds or more. If the SUS/RES switch is
continuously pressed for 4 seconds or longer, the personal computer is turned off.

When the computer is connected to a network using a LAN card or modem and when the peripheral
equipment is expanded with a PC card, you may not be ab le to use the suspend/resume function.
When you have expanded functions with a PC card, also check the manual for the cards you are
using.

Do not operate the SUS/RES switch when using Windows NT.
In the following cases, do not use the suspend function, but switch on/off the computer main unit

power supply with the main switch.

• When this computer is unused for a long period

When this computer will be unused longer than the effective period (about three days
maximum) for battery power for suspend mode, sa ve all data, close Windows 98, then s witch
off the main switch. If you suspend with the BIOS setup Suspend Mode set to Sa v e to Disk,
the power goes off with the main switch still on. In this case, it does not matter if you switch
off the main switch. The next time you switch on the main switch, operation resumes.

• When installing or removing options

There are some options that can be installed without switching off the main switch. See
SECTION 2 of this manual and the manual that comes with the option product.

In the suspend/resume operation, the screen may flick er for an instant depending on the situation.

22

Resuming

This personal computer can be resumed by the SUS/RES switch or the cover close switch.

Critical Point

When resuming this personal computer after it was suspended, resume it 10 or more seconds
after the last suspending operation.
The screen occasionally flickers during suspending/resuming operation.

Resuming with the SUS/RES switch
1 Press the SUS/RES switch for

resuming the personal computer.

As the SUS/RES switch is pressed, the

mark of the status indicator LCD stops
blinking and continues lighting. This
indicates that the personal computer is
in the operating status.

Resuming with the cover close switch
1 Fold out the LCD display.

The personal computer is resumed by the
cover close switch.

SUS/RES switch

Latch

Critical Point

When the Lid Open Resume of the BIOS setup is set to “Disabled”, the personal computer
won’t be resumed by folding out the LCD display.

SECTION 1

23

SECTION 1

7. Battery

Battery Charging

For portability, this computer can operate either from the AC adaptor or fr om its battery. This
item explains how to charge the battery.

1 Connect the AC adaptor.

2

3

First connect the AC power cord to the AC
adaptor (1), next connect the other cord of
the AC adaptor to the personal computer’s
DC-IN connector (2). Lastly, plug the AC
power cord into an AC outlet (3).

Relationship between computer modes and battery charging time

Main switch Computer mode Charging mode Charging time

ON

OFF

AC adaptor

1

Operating mode Standard charging About 10 hours

Suspend mode

Stopped

2 is displayed.

During charging, is displayed on the
status indicator LCD and the remaining battery
charge is displayed.

Quick charge About 4 hours

Critical Point

When the battery charging indicator ( ) goes out and the remaining battery charge indicator
at the leftmost end changes its mode from blinking ( ) to continuous lighting
(

), charging the battery is complete.
Spend a considerable time for charging the battery so that it is charged to the full.
If the ambient temperature is too low, the battery declines in its charging performance.
If the battery is charged just after it was used, charging may result in failure because the
battery temperature has risen and the battery protection function is activated. In such the
case, let the battery remaining in the charging status and charging will start as the battery
temperature drops.

24

Battery Operation

This item explains operation with the battery.

1 Disconnect the AC adaptor and

switch on the main switch.

Main switch

Slide the main switch in the direction of the

side).

arrow (

is displayed.

2 When the MAIN switch is on, press

the SUS/RES switch.

SUS/RES switch

stops flashing and stays lit up.

Critical Point

When the ambient temperature is lower, the battery operating time is reduced.
With this computer, the battery operating time depends on the conditions under which the
battery is used. Howev er , the operating time of a ne w , fully-charged battery is about 3 hours*.

* : About 6 hours when an extension battery pack is installed.
Condition: No optional equipment is connected with the computer and the power sa ving function

is activated by the BIOS Setup menu, etc. (the above-mentioned oper ation hours of the battery
is just a standard, and it varies depending on the operating condition).

SECTION 1

25

Checking the Remaining Battery Charge

This computer indicates the amount of battery charge remaining with the remaining battery
charge indicator on the status indicator LCD.

Remaining battery charge indicator

Indicates battery charge level of about 76% to about 100%
Indicates battery charge level of about 51% to about 75%
Indicates battery charge level of about 26% to about 50%

Indicates battery charge level of about 16% to about 25%
Indicates the low battery state (battery charge level of about 15% or lower). The w arning

beeps and
Indicates that the battery has run out (0% charge level).

flashes.

Critical Point

Indication of the remaining battery charge indicator ( ) may be slightly different from the
real remaining charge rate depending on the operating environment (temperature, number of
times that the battery was previously charged and discharged, etc.) because of the
characteristic of the battery (lithium ionic battery).
When there is 90% or more of the battery capacity remaining in the battery after the AC
adapter is disconnected, the battery won’t be charged. Charging the battery starts when its
remaining power drops to 89 % or less of the capacity.

Battery abnormality indicator

Indicates that the battery can not be charged normally.

Critical Point

When is displayed, take out the battery pack and re-install it. If this display still remains,
the battery pack is abnormal, so replace it.

26

Low Battery State

This item explains the display when this computer’s battery is low and what to do.

1 The low battery is announced in the following way.

The warning beeps and the battery mark on the status indicator LCD flashes.

Critical Point

If the audio volume is set too low, you may not be able to hear the warning beep.

2 Press the SUS/RES switch.

When the battery goes low, quickly press the SUS/RES s witch to suspend oper ation. Since
the suspend/resume function works even if the computer is suspended during operation, the
program and data are not lost.

Critical Point

If you want to resume operation immediately, connect the AC adaptor, then press the SUS/
RES switch again.

3 Charge the battery.

Connect the AC adaptor to charge the battery.

Critical Point

Reading from and writing to the hard disk uses large amounts of power. When sa ving data to
the hard disk with the battery low, connect the AC adaptor.
If you leave this computer running with the battery low, it is suspended automatically. How­ever , if data is being read from or written to the hard disk or other media, the suspending waits
until that processing is complete.
If you continue using the computer with the battery low, in the worst case, the data being
created or saved may be lost. Quickly connect the AC adaptor.

SECTION 1

27

Replacing the Internal Battery Pack

Save the program to the hard disk or a floppy disk before replacing the Built-in battery pack.
This item explains how to replace the Built-in battery pack.

W ARNING

ELECTRIC SHOCK

Always turn off the computer main unit main switch and disconnect the AC adaptor
before installing/removing the Built-in battery pack in order to avoid electric shock.

1 Turn the main switch off and

disconnect the AC adaptor.

Main switch

Slide the main switch in the direction of the
arrow (to the
Disconnect the AC adaptor from the compu­ter main unit.

3 Take out the Built-in battery pack.

side).

2 Unlock the Built-in battery pack.

Release
button

Slide the release button located on the bottom
of the main unit (1) and slide the Built-in
battery pack lock (2) for unlocking.

Built-in battery
pack lock

1

2

Remove the Built-in battery pack while putting
fingers on the slit.

28

4 Install the new Built-in battery pack.

5 Lock the Built-in battery pack.

Built-in battery pack lock

SECTION 1

Install the new Built-in battery pack.

Lock the Built-in battery pack with the Built-in
battery pack lock that was once released in
the previous step 2.

Critical Point

Do not remove the Built-in battery pack except when its service life has expired.

29

Precautions for Battery Pack

WARNING

ELECTRIC SHOCK

All battery packs are extremely delicate products. When installing or removing one, do
not drop it or subject it to strong shocks. If this should happen, do not use that battery
pack in the interest of safely, because there is a risk of electric shock or malfunction.

Discharge

After you charge the battery pack, even if you store it without using it, over about 1 month it will
naturally discharge.
When the computer won’t be used for a considerably long time (f or one month or more), remo v e
the battery pack from the computer and keep it in a cool place. If the computer is left with the
battery pack set inside, the battery overdischarges and its service life is shortened.

Service life

• The battery pack is a consumption item. After y ou use it f or a long time , its charging capacity
drops.

• Replace the battery after about 300 to 500 charge/discharge cycles.

• When the battery operating time becomes extremely short, the battery has reached the end of
its service life.

To extend the battery operating time

Use the BIOS setup Power menu.

Conditions under which the battery operating time becomes shorter

• The battery operating time is influenced by the environmental temperature and the battery
operating time can be short at low temperature (5 C).

• If the battery is used for a considerably long time, it deteriorates in the charging capacity
and charging performance. When the internal battery falls into such the condition, replace it
with a new one.

Use the AC adaptor in the following cases

• When using the hard disk, CD-ROM or DVD-ROM, etc. frequently

• When using a LAN or a Modem

30

SECTION 1

8. Port Replicator

Attaching the port replicator

This item explains how to attach the port replicator.

WARNING

ELECTRIC SHOCK

Always turn off the computer main unit main switch and disconnect the AC adapter
before attaching the port replicator in order to avoid electric shock.

Important

Do not carry your personal computer with the port replicator attached to it, otherwise
the port replicator might fall off and break.

1 Attach the port replicator to your personal computer.

Connector

Align the port replicator connector on the lower surface of your personal computer with the
connector on top of the port replicator, then push down the computer to connect it securely.

SECTION 1

31

Detaching the port replicator

This item explains how to detach the port replicator.

WARNING

ELECTRIC SHOCK

Always turn off the computer main unit main switch and disconnect the AC adapter
before detaching the port replicator in order to avoid electric shock.

1 Release the lock.

Slide the port replicator release button to the
right to release the lock.

2 Detach the port replicator from your

personal computer.

Lift up the personal computer to detach it from
the port replicator.

32

SECTION 1

9. Built-in LAN (local-area network) device

Connection

This item explains how to connect a LAN cable into the LAN connector.

W ARNING

ELECTRIC SHOCK

Be sure to turn off your personal computer and disconnect the AC adaptor from it be­fore connecting a LAN cable to the computer , otherwise you might get an electric shock.

ELECTRIC SHOCK

When it thunders in the neighborhood, immediately turn off your personal computer
and disconnect the AC adaptor and the LAN cable from it, otherwise your computer
might be struck and broken by lightening and thus cause a fire.

CAUTION

ELECTRIC SHOCK

Do not touch the LAN connector with your finger, otherwise you might get an electric
shock.

1 Turn off the computer and disconnect the AC adaptor from it.
2 Plug a LAN cable into the LAN connector on your personal computer or port replicator to

connect it to a network.

SECTION 1

Critical Point

To unplug the LAN cable from the LAN connector, pull the jack
while holding down the clip. Failure to do so might damage the
jack, cable or connector.
Y our computer consumes more electric energy when it is connected
to a LAN. When using a LAN, therefore, it is advisable to use the
AC adaptor to supply power to your computer.

33

SECTION 1

10.Internal FAX Modem

This item explains how to plug a modular cable into the modular connector.

Connection

WARNING

ELECTRIC SHOCK

Be sure to turn off your personal computer and disconnect the AC adaptor from it before
connecting a modular cable to the computer, otherwise y ou might get an electric shock.

ELECTRIC SHOCK

When it thunders in the neighborhood, immediately turn off your personal computer
and disconnect the AC adaptor and the modular cable from the computer, otherwise
your computer might be struck and broken by lightening and thus cause a fire.

CAUTION

ELECTRIC SHOCK

Do not touch the modular connector with your finger, otherwise y ou might get an electric shock.

1 Turn off the computer and disconnect

the AC adaptor from it.

2 Using a modular cable, connect the

computer to the telephone line.

Critical Point

To disconnect the modular cable from the connector, pull the jack
while holding down the clip. Failure to do so might damage the
jack, cable or connector.
Your computer consumes more electric energy when using the
built-in modem. When using the modem, therefore, it is advisable
to use the AC adaptor to supply power to your computer.

CAUTION

The internal modem has a maximum speed of 56000bps by ITU-T V.90 standard. Its
maximum speed of 53000bps is the highest allowed by FCC , and its actual connection
rate depends on the line conditions. The maximum speed is 33600bps at upload.

CAUTION

The internal modem is not intended for use with Digital PBX systems. Do not connect
the internal modem to a digital PBX as it may cause serious damage to the internal
modem or your entire notebook.
Consult your PBX manufacturer’s documentation for details. Some hotels have digital
PBX systems.
Be sure to find out BEFORE you connect your modem.

34

SECTIONSECTION

SECTION

SECTIONSECTION

SECTIONSECTION

SECTION

SECTIONSECTION

22

2

22

22

2

22

SECTION 2

SECTION 2

1. Options

What is the Options

You can expand the functions of this computer by connecting various options. Connecting options
such as a printer or a modem card makes it possible to print documents created with this computer
and to communicate them to other computers.
Other options include hard disks and expansion memory. Install options to match this computer to
your requirement.

Numeric key pad

SCSI card

Floppy Disk Unit

Printer

CRT display

Mouse

IC
memory
card

Port replicator

Built-in PC cards
Drive Unit

Built-in Super disk
drive unit

Built-in CD-ROM or
CD-R/RW Drive Unit

Built-in DVD-ROM
Drive Unit

Built-in 2nd battery
pack

Weight Saver

36

Expansion
RAM module

LAN card

Built-in
battery pack

WARNING

ELECTRIC SHOCK

Only connect equipment recommended by Fujitsu.
Connecting any other equipment can cause electric shock, fire, or breakdown.

CAUTION

INJURY

When installing/removing options, do not remove an y screws other than those specified
by this manual.
Removing any other screws can cause injury and breakdown.

BREAKDOWN

Read this manual carefully and connect cables correctly. If you use this computer with
cables connected incorrectly, this can cause breakdown of the computer main unit and
of the peripheral equipment.

SECTION 2

37

SECTION 2

2. PC Cards

Precautions for PC Cards

Observe the following points when using PC cards to prevent breakdown.

Do not place PC cards in high­temperature locations and loca­tions subject to direct sunlight.

Do not place heavy objects on
top of PC cards.

Do not subject PC cards to
strong shocks.

Be careful to avoid spilling coffee
and other liquids on PC cards.

Critical Point

This computer does not support the PC card driven by 12V DC power.

Avoid rubbing PC cards and
building up static electricity.

When storing a PC card, always
place it in its special case.

38

Installing PC Cards

PC card is a generic term for business card sized cards which have a program and data
memory function or peripheral equipment functions such as a modem or LAN adaptor. This
item explains how to install a PC card.

Critical Point

For some PC cards, the main power s witch
should be turned off. Refer to the manual
attached to your PC card.
In order to avoid damage, be careful not
to knock or put anything on top of the con­nection point between the PC card and the
cord.
On shipment of this computer, a dummy
card is inserted into the PC card slot for
preventing the new computer from getting
dust and foreign substances inside. After
removing the dummy card from the com­puter, carefully keep it for use in future.

2 Set a PC card in the PC card slot.

1 Remove the dummy card from the PC

card slot.

PC card eject/lock
button

Raise the PC card eject/lock button and press
it. The dummy card is ejected from the PC card
slot.

3 Lock the PC card.

Dummy card

SECTION 2

PC card

Insert a PC card with the product name side
up into the PC card slot completely.

PC card eject/lock
button

Pull out the PC card eject/lock button
completely and then tilt it down to lock the PC
card with the fastener.

39

Removing PC Cards

This item explains how to remove a PC card.

1 Click the PC card icon on the task bar.

Critical Point

Don’t eject the PC card by clicking “Stop” on the “PC card (PCMCIA) properties” window that
appears when “PC card” icon on the task bar is doub le clicked or “PC card” icon on the control
panel is clicked. If done so, the computer may unstably operate or malfunction.

2 Click “Discontinue XXXXXXXX”.

The name of the PC card set in the slot appears replacing XXXXXXXX.
The PC card stops operation and the screen changes for the next to appear.

Critical Point

For IC memory cards, the “This device cannot be removed” message may appear. If this
message does appear, close Windows 98 and switch off the computer main unit pow er before
removing the IC memory card.

3 Click OK.

40

4 Raise the PC card eject/lock button.

5 Remove the PC card.

SECTION 2

PC card eject/
lock button

6 Set the dummy card in the PC card

slot.

PC card eject/
lock button

After inserting the dummy card into the PC
card slot completely , pull out the PC card eject/
lock button entirely and then tilt it down to the
front side to lock the dummy card.

Dummy
card

PC card eject/
lock button

Press the PC card eject/lock button to eject
the PC card.

PC card

Critical Point

Never remove a PC card by pulling on its
cord.
Pulling on the cord can break the PC card.
Always use the procedure above for
removing PC cards. Removing PC cards
in any other way can cause breakdown.

41

SECTION 2

3. Expansion RAM Modules

Installing an Expansion RAM Module

This item explains how to install expansion RAM modules.

WARNING

ELECTRIC SHOCK

Always turn off the computer main
unit main switch and disconnect
the AC adaptor when installing an
expansion RAM module in order to
avoid electric shock.

2 Remove the cover of the expansion

RAM module slot.

Slot cover

1 Turn off the main switch and

disconnect the AC adaptor.

Main switch

Slide the main switch in the direction of the
arrow (to the
Disconnect the AC adaptor from the main unit.

3 Install the expansion RAM module.

side).

Take out the screws on the bottom of the
computer main unit and remove the cover of
the expansion RAM module slot.

42

notch

Align the notch of the expansion RAM module
with the projection on the connector, insert
firmly diagonally from above and push down
until the module clicks into place.

4 Fit the cover of the expansion RAM

module slot.

Slot cover

Fit the cover removed in 2.

CAUTION

DAMAGE

The expansion RAM module is made up of parts that are extremely vulnerable to static
electricity and can be damaged by the static electricity built up inside the main unit.
When installing or removing an expansion RAM module, hold it by the edges. Do not
touch any terminals or ICs. Also , do not touch any parts or terminals within the computer
main unit.

Checking expansion memory

To check the extended memory capacity after installing an expansion RAM module, look at the
DIMM item of the BIOS setup info. menu. For example, when a 64 MB expansion RAM module
has been installed, “64 MB” is indicated in the DIMM item. If the memory capacity indicated in the
DIMM item is not increased after installing an expansion RAM module though it has correctly
been installed, it is thinkable that the RAM module is faulty or defectiv e. In such the case, consult
with the store at which you purchased the RAM module about the trouble.

SECTION 2

43

Removing an Expansion RAM Module

This item explains how to remove an expansion RAM module.

WARNING

ELECTRIC SHOCK

Always turn off the computer main unit main switch and disconnect the AC adaptor
when removing an expansion RAM module in order to avoid electric shock.

1 Turn off the main switch and

disconnect the AC adaptor.

Main switch

Slide the main switch in the direction of the

hook

side).

Expansion RAM
module

arrow (to the
Disconnect the AC adaptor from the main unit.

3 Remove the expansion RAM module.

2 Remove the cover of the expansion

RAM module slot.

Slot cover

Remove the cover of the expansion RAM
module slot on the bottom of the computer
main unit.

4 Fit the cover of the expansion RAM

module slot.

Slot cover

Open the hooks on both sides that retain the
expansion RAM module to the left and right,
then remove the expansion RAM module from
the slot.

44

Fit the cover removed in 2.

SECTION 2

4. Multi-bay Unit

Replacing multi-bay units

This item explains how to replace multi-bay units.

W ARNING

ELECTRIC SHOCK

Before replacing multi-bay units , be
sure to turn off your computer and
unplug the AC adapter from it,
otherwise you might get an electric
shock.

2 Remove the multi-bay unit.

1 Turn off the computer and

disconnect the AC adaptor from it.

SECTION 2

Main switch

3 Mount a multi-bay unit.

Release button

Raise the multi-bay unit release lever to
remove the multi-bay unit.

Multi-bay unit

Push in the unit as far as it will go with its
connector pointing inward.

45

Precautions on handling or using the multi-bay unit

To avoid possible trouble, always take the following precautions when handling or using the
multi-bay unit.

Do not keep the multi-bay unit in a place where the temperature can fall extremely low, rise
extremely high, or change greatly.

Do not place the multi-bay unit in a place exposed to direct sunlight or place any heat-radiating
apparatus.

Avoid keeping the multi-bay unit in a place subject to shocks or vibration.
Avoid using the multi-bay unit in a damp or dusty place.
Never use the multi-ba y unit when a foreign matter , f or example, liquid or a metal chip , has gotten

into it. If such a foreign matter gets into the multi-bay unit, consult your local dealer.
When the multi-bay unit is dirty , do not use any v olatile agent such as benzine or thinner to clean

it. In such a case, wipe the dirt off with a soft dry cloth or a soft cloth moistened with water or
neutral detergent thinned with water.

Never disassemble or take apart the multi-bay unit.
Avoid using or k eeping the multi-bay unit near a magnet or an apparatus with a strong magnetic

field.

46

Loading/Ejecting disks

This item explains how to load and eject a disk in/from the CD-ROM drive or DVD-ROM drive
mounted in the multi bay.

Critical Point

You can only install/eject a Disk when the
computer main unit is in operating mode
because of the electronic lock of the CD­ROM/DVD-ROM drive.

2 Pull the tray out.

1 Press the EJECT button.

SECTION 2

EJECT button

The tray springs out slightly.

3 Put in the Disk.

Pull the tray out gently.

Place the Disk in the center of the tray with its
label facing upwards.

47

4 Set the tray.

Push the tray in gently.

Critical Point

If the tray cannot be pushed to the innermost position, pull it out until it clicks and try to push
it deeply once more.
When ejecting a Disk, carry out the same procedure as for loading.
If for some reason the tray does not come out when y ou press the eject button, insert something
like a ball-point pen into the hole to the right of the EJECT button on the unit and pull out the
tray.

48

Loading/Ejecting an LS-120 disk

This item explains how to load/eject an LS-120 disk in/from the LS-120 disk drive.

Loading an LS-120 disk

Insert an LS-120 disk into the LS-120

disk drive.

Insert an LS-120 disk into the LS-120 disk
drive with its label side up and the shutter
facing inwards.

Ejecting an LS-120 disk

Press the EJECT button.

EJECT button

Before pressing the EJECT button, make sure
that both the LS-120 disk drive access lamp

on the status indicator LCD are not

and
displayed.

Critical Point

Since the LS-120 disk drive of this personal computer locks the
disk electronically, any LS-120 disk can be ejected only when

the personal computer is in the operating mode. If the LS-120
disk is not ejected for some reason, insert the tip of a paper clip
into the EJECT hole. The disk will be ejected.

Ejecting an LS-120 disk while the LS-120 disk drive access lamp
or on the status indicator LCD is lighted might damage the
data recorded on the disk.

To protect data stored in an LS-120 disk from erasure or to prevent additional data writing on
a disk, slide the write enable tab of disk to make the square hole open (write inhibit status). To

make the disk enabled for o verwriting or additional writing, slide the write enable tab again to
shut the square hole (write enabled status).

SECTION 2

49

SECTION 2

5. Floppy Disk Unit

Installing a Floppy Disk Unit

This item explains how to install a floppy disk unit.

WARNING

ELECTRIC SHOCK

Always turn off the computer main
unit main switch and disconnect
the AC adaptor when installing a
floppy disk unit in order to avoid
electric shock.

2 Attach the port replicator to your

personal computer.

1 Turn the main switch off and

disconnect the AC adaptor.

Slide the main switch in the direction of the
arrow (to the
Disconnect the AC adaptor from the computer
main unit.

3 Install the floppy disk unit.

side).

Connector

50

Plug the FDD unit cable into the FDD
connector of the port replicator.

Precautions for Floppy Disk Unit

Take the following precautions when using the floppy disk unit in order to prevent damaging
it.

Avoid storing the floppy disk unit in extremely hot and cold locations, or in locations subject to
severe temperature changes.

Keep the floppy disk unit out of direct sunlight and away from heating equipment.
Avoid storing the floppy disk unit in locations subject to shock or vibration.
Avoid using the floppy disk unit in damp or dusty locations.
Never use the flopp y disk unit with any liquid, metal or other f oreign matter inside it. If any f oreign

matter gets inside the floppy disk unit, consult the store from where it was purchased or a Fujitsu
service center.

Wipe the floppy disk unit clean with a dry soft cloth or with a soft cloth moistened with water or a
neutral detergent thinned with water. Never use benzine, paint thinner or other volatile material.

Never disassemble or dismantle this product.

Critical Point

Use the floppy disk unit away from equipment that creates a magnetic field such as a CRT
monitor or an AC adaptor.

SECTION 2

51

Removing a Floppy Disk Unit

This item explains how to remove a floppy disk unit.

WARNING

ELECTRIC SHOCK

Always turn off the computer main
unit main switch and disconnect
the AC adaptor when removing a
floppy disk unit in order to avoid
electric shock.

2 Remove the floppy disk unit.

1 Turn off the main switch and

disconnect the AC adaptor.

MAIN switch

Slide the main switch in the direction of the
arrow (to the side).
Disconnect the AC adaptor from the main unit.

Critical Point

When you remove a connector , press both
sides of the connector and pull it. Pulling
a cable unnecessarily can cause damage.

52

What is a Floppy Disk?

A floppy disk is a medium for storing programs or data. This item explains basic knowledge
and precautions regarding floppy disks.

Types of floppy disks

If floppy disks are classified according to the amount of data they can store (the memory capacity),
typically there are 2 types.

HD mark or no mark

• 2HD floppy disks
These have 1.44MB (megabyte: unit of data

amount) and 1.2MB memory capacities.

• 2DD floppy disks
These have 720KB (kilobyte) memory ca-

pacities, half of the 2HDs.
The differences between the 2 kinds of

floppy disks are shown in the diagram on
the right.

Hole or no hole

3 mode drive

This computer’s floppy disk drive is a 3 mode drive that can read 1.44MB, 1.2MB and 720KB
memory capacity floppy disks. Therefore it can read nearly all floppy disks. However, when
exchanging data with another computer , you hav e to be careful if the other computer’s flopp y disk
drive is not a 3 mode drive. For example, if the other computer can read 1.2MB floppy disks but
not 1.44MB floppy disks, you ha v e to enter the data after putting it into 1.2MB f ormat in advance
with this computer.

SECTION 2

Critical Point

Some floppy disks cannot be read by this computer, depending on the floppy disk format.

53

Precautions on Handling

Take the following precautions when using floppy disks in order to avoid damaging them.

Be careful not to spill liquids such
as coffee onto them.

Never touch the surface of the
disk.

Do not place them in places with
high temperatures or in direct
sunlight.

Do not bring them near to
magnetic fields.

Do not bend them or place heavy
objects on top of them.

Do not stick labels on over each
other.

54

Loading/Ejecting a Floppy Disk

This item explains how to load and eject floppy disks.

Loading

Insert into the floppy disk drive.

Label

Eject button

Insert the floppy disk with the label upwards
and the shutter side first until the EJECT
button springs out.

Critical Point

If you eject the floppy disk while the flopp y disk
unit’s access lamp is still on, there is a risk of
losing the data on the disk.
When you do not want to erase the data sav ed
on the disk, or when you do not want to write
additional data, slide the floppy disk’s Write
enable tab so that the hole is open (WRITE
PROTECT state). When y ou want to write data
again, slide the Write enable tab so that the
hole is closed.

Ejecting

Press the EJECT button.

Access lamp

EJECT button

Check that the floppy disk unit’ s access lamp
is out, then press the EJECT button.

Write enable tab

SECTION 2

WRITE

ENABLE

WRITE

PROTECT

55

SECTION 2

6. Mouse

Connecting the Mouse

The following explains the way to connect the mouse.

1 Turn the main switch off and

disconnect the AC adaptor.

Main Switch

Slide the main switch in the direction of the
arrow (to the

side).

2 Connect the connector at the end of the

mouse cable to the mouse connector
on the rear side of the port replicator.

Have the arrow marked on the connector
facing up.

Using the Mouse

Moving the Mouse.

Place your hand on the mouse so that your fingers are resting on the left and right buttons and
move the mouse by sliding it over your desktop or other smooth surface. The arrow (called the
mouse pointer) on the screen moves in the same wa y as the mouse. Try moving the mouse while
watching the screen.

56

Button operations

• Click

Click

• Double click

Click, click

• Pointing

Press the left mouse button once until it clicks.
The action of pressing the right button once firmly
enough that it clicks is called a “right click”.

Press the mouse left button two times quickly in a
row.

SECTION 2

Align the mouse pointer with a menu item. When
there is another level for the men u item the cursor
is on (when > is displayed at the right of the menu
item), that menu level is displayed.

• Dragging

Press

Release

Move the mouse pointer with the mouse left button
held down, then release the button at the desired
position.

57

SECTION 2

7. Numeric Keypad

Connecting a Numeric Keypad

This item explains how to connect a numeric keypad.

1 Switch off the main switch.

Main switch

Slide the main switch in the direction of the
arrow ( side).

2 Plug the cable of the numeric keypad

into the expansion keyboard connector
on the rear panel of the port replicator.

Have the arrow marked on the connector
facing up.

Critical Point

The numeric keypad can be connected while the computer is being suspended.
The numeric keypad can be used only when the computer is set in the numeric keypad operation
mode.
When a mouse is connected to the numeric keypad
mouse connector, the mouse connector on the
computer main unit cannot be used.

Mouse connector

You can adjust the tilt of the numeric keypad with
the tilt feet on the bottom of the numeric keypad.

58

SECTION 2

8. CRT Monitor

Connecting an External CRT Monitor

An external CRT monitor can be connected to this computer . This item explains how to connect
a CRT monitor to the CRT connector on the rear of the computer main unit.

W ARNING

ELECTRIC SHOCK

Always switch off the computer main unit main switch and disconnect the AC adaptor
before connecting/disconnecting a CRT monitor. Connecting/disconnecting a CRT
monitor with the power on can cause electric shock.

CAUTION

BREAKDOWN

When connecting cables, read this manual carefully and make sure to connect cor­rectly. Using this computer with cables incorrectly connected can cause breakdo wn of
the computer main unit and the CRT monitor.

1 Switch off the main switch and disconnect the AC adaptor.

Main switch

Slide the main switch in the direction of the arrow (
Disconnect the AC adaptor.

side).

SECTION 2

59

2 Connect the CRT monitor to the computer main unit.

Plug the CRT cable securely into both the connector of the CR T monitor and the CRT connector
of your personal computer or port replicater, then fix them with screws.

Critical Point

For making the image clearer on the CRT displa y , connect the CRT cab le to the CRT connector
of the computer.

3 Connect the CRT monitor’s power cord and switch on its power.

4 Connect the AC adaptor to the computer main unit and switch on main switch.

5 Switch the screen display.

When you press Fn + F10, the display switches to the next step in the sequence:
LCD -> simultaneous display -> CRT -> LCD.

60

SECTION 2

9. CCD Camera

Focus dial

1

Lens

2

Shutter release button

3

Eject button

4

Connector

5

SECTION 2

1 Focus dial

Turn this dial to bring the lens into focus.

2 Lens

Point the lens at the camera subject.

3 Shutter release button

Press this button to take a digital still picture or to start digital video recording.

4 Eject button

Press this button to draw out the CCD camera from the CCD camera unit.

5 Connector

Connector for connecting the CCD camera unit to the personal computer.

61

Using CCD camera

1

2

When the CCD camera is connected to the personal computer, y ou can enjoy digital still pictures
and digital video pictures on the personal computer.
This item explains the following procedures.

• Connection of the CCD camera

Preparing required things

Connect the CCD camera to the USB connector of the personal computer for taking digital still
pictures and recording digital video pictures.

Connecting the CCD camera

ADVICE

When an application (eg: Microsoft Netmeeting) is being activated, do not connect/
disconnect the CCD camera to /from the personal computer.
The application may not work. Be sure to quit the application before connecting/
disconnecting the CCD camera to/from the personal computer.

CAUTION

Trouble

Correctly connect the CCD camera to the personal computer following the instructions
of the user’s guide. If the CCD camera is used in wrong connection, it may damage the
CCD camera or/and the personal computer.

Using the CCD camera with the CCD camera unit built in the personal computer
1 Connect the CCD camera unit to the personal computer.

“Replacing mobile multibay unit”.

2 Draw out the CCD camera.

1 Press the Eject button of the CCD camera

unit, and the CCD camera sticks out by 1cm
or so.

2 Draw out the CCD camera gently until a

clicking sound is heard.

62

Eject button

3 Raise the CCD camera to release it from

the projecting catch of the CCD camera unit
and adjust the angle of the camera.

projecting catch

IMPORTANT

Note on camera angle

The CCD camera can be turned at an angle of 45( (clockwise) or 90( (counterclockwise)
at the maximum. Do not turn the CCD camera furthermore.

Using the CCD camera externally connected to the personal computer

1 Draw out the CCD camera.

“Using the CCD camera with the CCD camera
unit built in the personal computer”, Step 2.

2 Raise the CCD camera to release it from the

projecting catch of the CCD camera unit.

SECTION 2

3 Remove the CCD camera from the CCD camera unit.

Gently draw the CCD camera out of the CCD
camera unit while holding the CCD camera by
the lower part.

projecting catch

root

63

4 Connect the CCD camera to the personal

1

2

computer with the connecting cable.

1 Connect the smaller connector of the

connecting cable to the connector of the
CCD camera.

2 Connect the larger connector of the

connecting cable to the USB connector on
the rear of the personal computer.

ADVICE

Using the CCD camera fixed to the latch of the personal computer
The CCD camera can be used as it is fixed to the latch of the personal computer.

CCD camera

Personal
computer

1 Fit the CCD camera fixing clip (supplied as

an accessory) to the latch of the personal
computer.

2 Fit the CCD camera to the CCD camera

fixing clip.

3 Connect the CCD camera to the personal

computer using the connecting cable.

CCD camera
fixing clip

Latch

CCD camera
fixing clip

Connecting
cable

64

Removing the CCD camera from personal computer

When the CCD camera was used as it was externally connected to the personal computer

1 Connect the CCD camera to the CCD

camera unit.

Plug the connector of the CCD camera with
its flat side up into the jack of the unit.

Flat side

2 Lock the CCD camera

Tilt down the CCD camera keeping its upper
part leveled with the lower part. Make sure
the CCD camera is locked by the projecting
catch.

Projecting catch

3 Push the CCD camera

Pressing the Eject button on the CCD camera
unit (1), gently push the CCD camera into
the unit (2).

2

1

Eject button

When the CCD camera was used with CCD camera unit built in the personal computer

1 Push back the CCD camera into the CCD camera unit.

“When the CCD camera was used as it was externally connected to the personal computer”.
Step 2 and 3.

SECTION 2

2 Remove the CCD camera unit from the personal computer.

“Replacing mobile multibay unit”

65

SECTION 2

10.One Touch Operation buttons

The one touch operation buttons function as quick access for pre-configured applications , browser or
e-mail. It enables users to start a program quickly with a single press on the buttons.

Internet E-Mail

1 2 3 4

1 Start an application.

Press the button to start an application.

2 Start an application.

Press the button to start an application.

3 Internet

Press this button to start your default browser.

4 E-mail

Press this button to launch your email program.

Critical Point

The one-touch operation buttons cannot be used in the following cases.

The MAIN switch is set at the OFF position (slid to the “ ” side).

66

SECTIONSECTION

SECTION

SECTIONSECTION

SECTIONSECTION

SECTION

SECTIONSECTION

33

3

33

33

3

33

SECTION 3

SECTION 3

”

1. BIOS setup

Snapshots of the BIOS setup screen and the possible setup options is shown in the following sections .

Underlined setup options show the default settings.
Columns between Selections and Note show the security level of each setup item. ‘S’ means

that the item needs the supervisor password security level and can not be changed with the
user password security level.

1.1 Main Menu

Main Advanced Security Power Boot Info Exit

System Time: [12:34:56]
System Date: [02/22/2000]

Floppy Disk A: [1.44/1.2 MB 3.5”]

:Primary Master:
:Primary Slave [UJDA310-(PS)]

Language: [English (US)]

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-MenuF10Save and Exit

PhoenixBIOS Setup Utility

[FUJITSU MHK2090AT-(PM)

]

Figure 1-1 Main menu

Item Specific Help

Adjust calendar clock

<Tab>, <Shift-Tab>, or
<Enter> selects field.

Setup Item Selections Note (Item Specific Help)

System Time 00:00:00 to 23:59:59 Adjust calendar clock.

<Tab>, <Shift-Tab>, or <Enter> selects field.

System Date 01/01/1981 to

12/31/2099

Floppy Diskette A Disabled

1.44/1.25 MB 3 1/2”

Adjust calendar clock.
<Tab>, <Shift-Tab>, or <Enter> selects field.

S Select floppy drive type. 1.44/1.25 MB 3 1/2

is the valid value.
Selects floppy type. Note that 1.25 MB, 3

1/2” references a 1024 byte/sector
Japanese media format.

Primary Master Configure primary master ATA/ATAPI

device. Configures ATA/ATAPI device.

Primary Slave Configure primary slave ATA/ATAPI device.

Configures ATA/ATAPI device.

Language

English (US)
xxxxxx (JP)

The default setting differs between
US/European model and Japanese model.

Select the display language for the BIOS.

Table 1-1 Main menu options

68

1.1.1 Main - Primary Master and Primary Slave Menu

Main Advanced Security Power Boot Info Exit

Primary Master [FUJITSU MHK2090AT-(PM)]

PhoenixBIOS Setup Utility

Item Specific Help

Type: [AUTO]
Maximum Capacity: 9042 MB

Multi-Sector Transfers: [16 Sectors]
LBA Mode Control: [Enabled]
PIO Transfer Mode: [Fast PIO 4]
DMA Transfer Mode: [Ultra DMA 2]

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-Menu F10Save and Exit

Select ATA/ATAPI
drive installed here.

[Auto]
The BIOS auto-type
the drive on boot
time.

Except [Auto]
You enter parameters
of the drive.

[None]
The drive is disabled.

Figure 1-2 Main - Primary Master and Primary Slave Menu

Setup Item Selections Note (Item Specific Help)

Type Auto

None
CD-ROM

ATAPI Removable
User

Select ATA/ATAPI device type. If ‘Auto’ is
selected, the type is automatically identified at

POST by the BIOS. It does not carry out
Cylinder/Head/Sector display in the case of

over 8.4GB-HDD when Auto mode. If ‘None’
is selected, all of the following setup items do

not appear. When ‘User’ is selected, you can
specify Cylinders, Heads and Sectors.

User = you enter parameters of hard-disk drive
installed at this connection.
Auto = autotypes ATA/ATAPI drive installed

here.
CD-ROM = a CD-ROM drive is installed here.

ATAPI Removable = removable disk drive is
installed here.

Cylinders 0 to 65535 S This item appears when ‘Auto’ is selected

and the type is identified as hard disk, or
‘User’ is selected. When ‘User’ is selected,

you can change the value.
Specify the number of Cylinders.

Heads 1 to 16 S This item appears when ‘Auto’ is selected

and the type is identified as hard disk, or
‘User’ is selected. When ‘User’ is selected,

you can change the value.
Specify the number of Heads.

SECTION 3

69

Setup Item Selections Note (Item Specific Help)

Sectors 0 to 63 S This item appears when ‘Auto’ is selected

Maximum Capacity xxxx MB Display maximum capacity calculated from

Multi-Sector
Transfers

LBA Mode Control

Transfer Mode

Ultra DMA Mode

Disabled
2 Sectors

4 Sectors
8 Sectors
16 Sectors

32 Sectors
64 Sectors

128 Sectors
Disabled

Enabled

Standard
Fast PIO 1
Fast PIO 2

Fast PIO 3
Fast PIO 4

Disabled
Multiword DMA 1

Multiword DMA 2
Ultra DMA 0

Ultra DMA 1
Ultra DMA 2

Table 1-2 Main - Primary Master and Primary Slave Menu options

and the type is identified as hard disk, or
‘User’ is selected. When ‘User’ is selected,
you can change the value.

Specify the number of Sectors.

parameters of hard disk when ‘Auto’ is
selected and the type is identified as hard disk,
or ‘User’ is selected.

S This option can not be changed when ‘Auto’

is selected.
Specify the number of sectors per block for

multiple sector transfer. ‘MAX’ refers to the
size the disk returns when required.

S This option can not be changed when ‘Auto’

is selected.
Enabling LBA causes Logical Block

Addressing to be used in place of Cylinders,
Heads & Sectors.

S This option can not be changed when ‘Auto’

is selected. Multi-word DMA is automatically
set to mode 1 for ‘Fast PIO 1’, ‘Fast PIO 2’,

‘Fast PIO 3’ and set to mode 2 for ‘Fast PIO
4’.

Selects the method of moving data to/from the
drive. Autotype the drive to select the optimum

transfer mode.

S You can not change this option when ‘Auto’

is selected.
Selects the Ultra DMA mode used for moving
data to/from the drive. Autotype the drive to

select the optimum transfer mode.

70

1.1.2 Main - Primary Master and Primary Slave Menu

Main Advanced Security Power Boot Info Exit

Primary Slave [UJDA310-(PS)]

PhoenixBIOS Setup Utility

Item Specific Help

Type: [Auto]

Multi-Sector Transfers: [Disabled]
LBA Mode Control: [Disabled]
PIO Transfer Mode: [Fast PIO 4]
DMA Transfer Mode: [Disabled]

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-Menu F10Save and Exit

Select ATA/ATAPI
drive installed here.

[Auto]
The BIOS auto-type
the drive on boot
time.

Except [Auto]
You enter parameters
of the drive.

[None]
The drive is disabled.

Figure 1-2a Main - Primary Master and Primary Slave Menu

Setup Item Selections Note (Item Specific Help)

Type

Auto
None

CD-ROM
ATAPI Removable

User

Select ATA/ATAPI device type. If ‘Auto’ is
selected, the type is automatically identified at

POST by the BIOS. It does not carry out
Cylinder/Head/Sector display in the case of

over 8.4GB-HDD when Auto mode. If ‘None’
is selected, all of the following setup items do

not appear. When ‘User’ is selected, you can
specify Cylinders, Heads and Sectors.

User = you enter parameters of hard-disk drive
installed at this connection.

Auto = autotypes ATA/ATAPI drive installed
here.

CD-ROM = a CD-ROM drive is installed here.
ATAPI Removable = removable disk drive is

installed here.

Multi-Sector
Transfers

Disabled
2 Sectors

4 Sectors
8 Sectors

This option can not be changed when ‘Auto’
is selected.

Specify the number of sectors per block for

multiple sector transfer.
16 Sectors
32 Sectors
64 Sectors
128 Sectors

SECTION 3

71

Setup Item Selections Note (Item Specific Help)

LBA Mode Control Disabled

PIO Transfer Mode Standard

DMA Transfer Mode

Table 1-2 Main - Primary Master and Primary Slave Menu options

Enabled

Fast PIO 1
Fast PIO 2
Fast PIO 3

Fast PIO 4

Disabled
Multiword DMA 1

Multiword DMA 2
Ultra DMA 0

Ultra DMA 1
Ultra DMA 2

S This option can not be changed when ‘Auto’

is selected.
Enabling LBA causes Logical Block

Addressing to be used in place of Cylinders,
Heads & Sectors.

S This option can not be changed when ‘Auto’

is selected. Multi-word DMA is automatically
set to mode 1 for ‘Fast PIO 1’, ‘Fast PIO 2’,
‘Fast PIO 3’ and set to mode 2 for ‘Fast PIO

4’ .
Selects the method of moving data to/from the

drive. Autotype the drive to select the optimum
transfer mode.

S You can not change this option when ‘Auto’

is selected.
Selects the Ultra DMA mode used for moving
data to/from the drive. Autotype the drive to

select the optimum transfer mode.

72

1.2 Advanced Menu

Main Advanced Security Power Boot Info Exit

Plug & Play O/S [Yes]
Protected Device Configuration [No]

:Serial/Parallel Port Configurations
:Keyboard/Mouse Features
:Video Features
:Internal Devices Configurations
:PCI Configuration
:CPU Features
:ACPI Feature

:Event Logging

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-Menu F10Save and Exit

PhoenixBIOS Setup Utility

Item Specific Help

[No]
The BIOS configures
also non-boot devices.
Select if you are
using a non-Plug &
Play OS or a non-ACPI
OS

[Yes]
The BIOS configures
only boot devices.

Figure 1-3 Advanced menu

Setup Item Selections Note (Item Specific Help)

Plug & Play O/S

Secured Setup
Configurations

I/O Device

No
Yes

No
Yes

S Select ‘Yes’ if you are using a Plug & Play

capable operating system.
Select ‘No’ if you need the BIOS to configure

non-boot devices.

S ‘Yes’ prevents a Plug and Play Operating

System from changing system settings.
Peripheral Configuration.

Configuration
Keyboard/Mouse

Setup keyboard/mouse features.

Features
Video Features Setup video features.
PCI Configuration Additional setup menus to configure PCI

devices.

CPU Features Configure CPU features.
ACPI Features Configure ACPI features.

Event Logging Configure event logging features.

SECTION 3

Table 1-3 Advanced menu options

73

1.2.1 Advanced - Serial/Parallel Port Configuration Menu

Main Advanced Security Power Boot Info Exit

Serial/Parallel Port Configuration

PhoenixBIOS Setup Utility

Item Specific Help

Setup Item

Serial port

Base I/O address

Interrupt

Serial port B

Mode

Base I/O address

Serial port : [Enable]

I/O Address: [3F8-3FF]
Interrupt: [IRQ 4]

Infrared Port : [Enabled]

Mode: [FIR]
I/O Address: [2E8-2EF]
Interrupt: [IRQ 3]
I/O Address: [118-11F]
DMA Channel: [DMA 3]

Parallel Port: [Enabled]

Mode: [Bi-directional]
I/O Address: [378-37F]
Interrupt: [IRQ 7]

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-MenuF10Save and Exit

[Disabled]
The port is disabled

[Enabled]
The port is enabled
with user
configuration

[Auto]
A Plug & Play OS or
an ACPI OS will
configure the port.

Figure 1-4 Advanced - I/O Device Configuration menu

Selections

Disabled
Enabled
Auto

Note (Item Specific Help)

S

Configure serial port A using options:
[Disabled] No configuration
[Enabled] User configuration
[Auto] BIOS or OS chooses configuration

3F8-3FF
2F8-2FF
3E8-3EF

This option is available when Serial port A is

S

‘Enabled’.
Set the base I/O address for serial port A.

2E8-2EF
IRQ 3

IRQ 4
IRQ 10

S

This option is available when Serial port A is
‘Enabled’.
Set the interrupt for serial port A.

IRQ 11
Disabled

Enabled
Auto

S

Configure serial port B using options:
[Disabled] No configuration
[Enabled] User configuration
[Auto] BIOS or OS chooses configuration

IrDA
FIR

S

This option is available when Serial port B is
‘Enabled’.
Set the mode for serial port B.

3F8-3FF
2F8-2FF
3E8-3EF

S

This option is available when Serial port B is
‘Enabled’.
Set the base I/O address for serial port B.

2E8-2EF

74

Setup Item

Interrupt

Selections

IRQ 3
IRQ 4
IRQ 10
IRQ 11

Note (Item Specific Help)

S

This option is available when Serial port B is
‘Enabled’.
Set the interrupt for serial port B.

Base I/O address

DMA channel

Parallel port

Mode

Base I/O address

Interrupt

100-107
108-10F
110-117
118-11F

DMA 1
DMA 3

Disabled
Enabled
Auto

Output only
Bi-directional
ECP

378-37F
278-27F
3BC-3BF

IRQ 5
IRQ 7

Table 1-4 Advanced - I/O Device Configuration menu options

S

This option is available when Mode f or Serial
port B is set to ‘FIR’.
Set the base I/O address for the FIR of serial
port B.

S

This option is available when Mode f or Serial
port B is set to ‘FIR’.
Set the DMA channel for the FIR of serial port
B.

S

Configure parallel port using options:
[Disabled] No configuration
[Enabled] User configuration
[Auto] BIOS or OS chooses configuration

This option is available when Parallel port is

S

‘Enabled’. When you change this mode to
‘ECP’, ‘DMA 1’ is selected by default.
Set the mode for the parallel port.

This option is available when Parallel port is

S

‘Enabled’.
Set the base I/O address for the parallel port.

This option is available when Serial port B is

S

‘Enabled’.
Set the interrupt for the parallel port.

SECTION 3

75

1.2.2 Advanced - Keyboard/Mouse Features Menu

Main Advanced Security Power Boot Info Exit

Keyboard/Mouse Features

PhoenixBIOS Setup Utility

Item Specific Help

Setup Item

Numlock

Hot Plug

Internal Pointing
Device

Numlock: [Auto]
Hot plug: [Enabled]
Internal Pointing Device: [Auto Disabled]

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-MenuF10Save and Exit

Selects power-on
state for Numlock.

Figure 1-5 Advanced - Keyboard/Mouse Features menu

Selections

Auto

Note (Item Specific Help)

S

Selects Power-on state for Numlock.
On
Off

Disabled

S

Select Hot Pluggability.
Enabled

Auto Disabled
Always Enabled

S

If Always Enabled is selected, the internal

pointing device is always enabled. If Auto

Disabled is selected, the internal pointing

device is disabled when an external pointing

device is connected with the PS/2 port.

However, if no pointing device is connected,

the internal pointing device is enabled.

76

Table 1-5 Advanced - Keyboard/Mouse Features menu options

1.2.3 Advanced - Video Features Menu

Main Advanced Security Power Boot Info Exit

PhoenixBIOS Setup Utility

Video Features

Item Specific Help

Display: [Internal Flat Panel]
Compensation: [Disabled]

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-Menu F10Save and Exit

Select display
terminal.

Figure 1-6 Advanced - Video Features menu

Setup Item Selections Note (Item Specific Help)

Display

Internal Flat-Panel

Select display terminal.

External
Simultaneous

Compensation

Disabled

Select compensation.

Enabled

Table 1-6 Advanced - Video Features menu

SECTION 3

77

1.2.4 Advanced - Internal Device Configurations.

Main Advanced Security Power Boot Info Exit

Internal Device Configuration

PhoenixBIOS Setup Utility

Item Specific Help

Floppy Disk Controller: [Enabled]
IDE Controller: [Enabled]
LAN Controller [Auto]

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-Menu F10Save and Exit

Figure 1-6a Advanced - Internal Device Configurations

Setup Item

Floppy Disk Controller

IDE Controller

LAN Controller

Table 1-6a Advanced - Internal Device Configurations

Selections

Enabled
Disabled

Enabled
Disabled

[Auto]
Enabled
Disabled

[Disabled]
Floppy Disk drive is
disabled.

[Enabled]
Floppy Disk drive is
enabled.

Note (Item Specific Help)

[Disabled] Floppy Disk Drive is disabled.

[Enabled] Floppy Disk Drive is enabled.
[Disabled] IDE port is disabled.
[Enabled] IDE port is enabled.

[Disabled] The LAN device is disabled.
[Enabled] The LAN device is enabled.
[Auto] with AC power supply, the LAN is
always enabled. With the battery, the
device is enabled only when the link is
active.

78

1.2.5 Advanced - PCI Configuration Menu

Main Advanced Security Power Boot Info Exit

PhoenixBIOS Setup Utility

PCI Configuration

Item Specific Help

Setup Item

IRQ Reservation

:IRQ Reservation

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-MenuF10Save and Exit

Reserve specific
IRQs for use by
legacy ISA devices.

Figure 1-7 Advanced - PCI Configuration menu

Selections Note (Item Specific Help)

Reserve specific IRQs for use by legacy ISA
devices.

Table 1-7 Advanced - PCI Configuration menu options

SECTION 3

79

1.2.5.1 Advanced - PCI Configuration - IRQ Reservation Menu

Setup Item

IRQ 3

IRQ 4

IRQ 5

IRQ 7

IRQ 9

IRQ 10

Main Advanced Security Power Boot Info Exit

IRQ 3: [Available]
IRQ 4: [Available]
IRQ 5: [Available]
IRQ 7: [Available]
IRQ 9: [Available]
IRQ 10: [Available]
IRQ 11: [Available]
IRQ 15: [Available]

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-Menu F10Save and Exit

PhoenixBIOS Setup Utility

IRQ Reservation

Item Specific Help

Reserve the
specified IRQ for
use by legacy ISA
devices.

Figure 1-8 Advanced - PCI Configuration - IRQ Reservation menu

Selections

Available
Reserved

Note (Item Specific Help)

If [Reserved] is selected, the BIOS reserves

S

IRQ 3 for use by legacy ISA devices and does

not use it for embedded PCI or ISA devices.

IRQ 3 is removed from the IRQ bitmap in the

PCI IRQ routing table.

Reserve the specified IRQ for use by legacy

ISA devices.
Available

Reserved

Reserves IRQ 4.

S

Reserve the specified IRQ for use by legacy

ISA devices.
Available

Reserved

Reserves IRQ 5.

S

Reserve the specified IRQ for use by legacy

ISA devices.
Available

Reserved

Reserves IRQ 7.

S

Reserve the specified IRQ for use by legacy

ISA devices.
Available

Reserved

Reserves IRQ 9.

S

Reserve the specified IRQ for use by legacy

ISA devices.
Available

Reserved

Reserves IRQ 10.

Reserve the specified IRQ for use by legacy

ISA devices.

80

Setup Item

IRQ 11

Selections

Available
Reserved

IRQ 15

Available
Reserved

Table 1-8 Advanced - PCI Configuration - IRQ Reservation menu options

1.2.5.2 Advanced - CPU Features

Note (Item Specific Help)

Reserves IRQ 11.

S

Reserve the specified IRQ for use by legacy
ISA devices.

Reserves IRQ 15.

S

Reserve the specified IRQ for use by legacy
ISA devices.

Main Advanced Security Power Boot Info Exit

Processor Serial Number: [Disabled]

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-Menu F10Save and Exit

PhoenixBIOS Setup Utility

CPU Features

Item Specific Help

Configures Processor
Serial Number
features of Pentium
III processor.

[Disabled]
Processor Serial
Number features is
disabled.

[Enabled]
Processor Serial
Number features is
enabled.

Figure 1-9 Advanced - CPU Features

SECTION 3

81

1.2.5.3 Advanced - ACPI Features

Main Advanced Security Power Boot Info Exit

ACPI Management: [Disabled]

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-MenuF10Save and Exit

PhoenixBIOS Setup Utility

ACPI Features

Item Specific Help

Configures ACPI
management features.

[Disabled]
ACPI management is
disabled.

[Enabled]
ACPI management is
enabled.

Figure 1-10 Advanced - ACPI Features

82

1.2.6 Advanced - DMI Event Logging Menu

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-Menu F10Save and Exit

Setup Item

Event log capacity
Event log validity
Clear all event logs

Event Logging

View Event Log

Mark Events as Read

Main Advanced Security Power Boot Info Exit

Event Log Capacity: Space Available
Event Log Validity: Valid

View Event Log: [Enter]

Event Logging: [Enabled]

System Boot Event: [Disabled]

Clear All Event Logs: [No]

Mark Events as Read: [Enter]

PhoenixBIOS Setup Utility

DMI Event Logging

Item Specific Help

[No]
Event logs will not
be cleared at the
next boot.

[Yes]
All event logs will
be cleared at the
next boot. The value
is reset to [No]
after clearing logs.

Figure 1-11 Advanced - DMI Event Logging menu

Selections

Note (Item Specific Help)

Display event log capacity.
Display event log validity.

No
Yes

Disabled

‘Yes’ clears all DMI event logs at next boot.

S

The value is reset to ‘No’ after clearing logs.
Enables DMI event logging.

S

Enabled
[Enter]

Press Enter key to view the contents of the
event log.

[Enter]

Press Enter key to mark all events currently
in the event log as read. Marked events will
not be displayed from the next “View Event
Log”.

SECTION 3

Table 1-11 Advanced - DMI Event Logging menu options

83

1.3 Security Menu

Main Advanced Security Power Boot Info Exit

Supervisor Password Is: Clear
User Password Is: Clear

Set Supervisor Password [Enter]
Set User Password [Enter]
Minimum User Password Length [0]

Password on Boot: [Disabled]
Password on Resume: [Disabled]
Boot from Removable Media:[All]
Floppy Disk Access: [All]

:Hard Disk Security
:Owner Information

Hard Disk Boot Sector: [Normal]

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-Menu F10Save and Exit

Setup Item

Supervisor Password
Is

User Password Is
Set Supervisor

Password
Set User Password

Diskette access

Password on boot

Password on resume

PhoenixBIOS Setup Utility

Figure 1-12 Security menu

Selections

All
Supervisor Only

Disabled
Enabled

Disabled
Enabled

Item Specific Help

Press <Enter> key to
set Supervisor
Password to enable
any password
features.

Then password entry
is required to enter
BIOS Setup.

Note (Item Specific Help)

Display the setting of Supervisor password.

Display the setting of User password.

S

Supervisor Password controls access to the

setup utility.

User password can be set after Supervisor

password is set.

User Password controls access to the system

at boot.

S

This item can be set with Supervisor

password security level. When ‘Supervisor

Only’ is selected, floppy diskette drive is not

available with User password security level.

Controls access to diskette drives.

When Password on boot is ‘Enabled’, the

BIOS requires a password on OS boot.

Enables password entry on boot.

When Password on resume is ‘Enabled’, the

BIOS requires a password on resume.

84

Setup Item

Hardisk boot
sector

Hardisk security

Selections

Normal
Write Protect

Note (Item Specific Help)

S

Write protects boot sector on hard disk to
protect against viruses.

Primary Master

Disabled
Enabled

Secondary Master

Disabled
Enabled

Table 1-12 Security menu options

1.3.1 Set Supervisor Password

Supervisor Password Is: Clear

Set Supervisor Password

Enter New Password [ ]

Confirm New Password [ ]

Supervisor Password Is: Set

Set Supervisor Password

Enter Current Password [ ]

Enter New Password [ ]

Confirm New Password [ ]

S

This item can be set with Supervisor
password security level. When ‘Enabled’ is
selected, the data of the hard disk are
protected with the password lock feature of
the drive. You can not read any data on the
drive if it is not installed in the same system
as it is locked with the password.
Enables fixed disk security.

Protects secondary master hard disk.

S

1.3.2 Set User Password

User Password Is: Clear

Set User Password

Enter New Password [ ]

Confirm New Password [ ]

User Password Is: Set

Set User Password

Enter Current Password [ ]

Enter New Password [ ]

Confirm New Password [ ]

SECTION 3

85

1.4 Power Menu

Main Advanced Security Power Boot Info Exit

Power Savings: [Customized]

Hard Disk Timeout: [Off]
Display Timeout: [Off]
Standby Timeout: [Off]
Auto Suspend Timeout: [Off]

Suspend Mode: [Suspend]

Auto Save To Disk: [Off]

Resume On Modem Ring: [Off]
Resume On Time: [Off]
Resume Time: [00:00:00]

:Advanced Features

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-Menu F10Save and Exit

PhoenixBIOS Setup Utility

Item Specific Help

Select Power
Management Mode.
Choosing modes
changes system power
management settings.
Maximum Power Savings
conserves the
greatest amount of
system power while
Maximum Performance
conserves power but
allows greatest
system performance.
To alter these
settings, choose
Customize. To turn
off power management,
choose Disable.

Figure 1-13 Power menu

Setup Item

Power Savings

Hard Disk Timeout

Video Timeout

86

Selections

Disabled
Customized
Maximum Power
Savings
Maximum Performance

Off
30 Seconds
1 Minute
2 Minutes
4 Minutes
6 Minutes
8 Minutes
10 Minutes
15 Minutes
20 Minutes

Off
2 Minutes
4 Minutes
6 Minutes
8 Minutes
10 Minutes
15 Minutes
20 Minutes

Note (Item Specific Help)

Select Power Management Mode. Choosing

modes changes system power management

settings. Maxim um Pow er Savings conserves

the greatest amount of system power while

Maximum Perf ormance conserves power but

allows greatest system performance. To alter

these settings, choose Customized. To turn

off power management, choose Disabled.

Amount of time the hard disk needs to be

inactive before it is turned off.

Amount of time the user input devices need

to be inactive before the screen is turned off.

Setup Item

Standby Timeout

Auto Suspend
Timeout

Suspend Mode

Auto Save To Disk

Resume On Modem
Ring

Resume On Time

Resume Time

Selections

Off
1 Minute
2 Minutes
4 Minutes
6 Minutes
8 Minutes
12 Minutes
16 Minutes

Off
5 Minutes
10 Minutes
15 Minutes
20 Minutes
30 Minutes
40 Minutes
60 Minutes

Suspend
Save To Disk

Off
After 1 Hour

Off
On

Off
On

00:00:00 to 23:59:59

Note (Item Specific Help)

Amount of time the system needs to be
inactive before entering the Standby Mode.
Standby Mode turns off various devices in the
system, including the screen, until you start
using the computer again.

Amount of time the system needs to be
inactive before entering the Suspend Mode.

Select the type of Suspend Mode. If you
choose Save To Disk the system will save its
state to disk and power off. If you choose
Suspend the system will save its state but
remain in a low power mode. If you choose
Suspend then you also have the option of
choosing Auto Save To Disk.

Turn on or off the Auto Save To Disk feature.
When Auto Save To Disk is turned on, the
system will save its state to disk and then
power off after being in Suspend mode for a
period of time.

Turning this feature on will wake the system
up when an incoming call is detected on your
modem in Suspend Mode.

Turning this feature on will wake the system
up at ‘Resume Time’ from Suspend Mode.

Specify the time when the system is to wake
up. <Tab>, <Shift-Tab>, or <Enter> selects
field.

SECTION 3

Advanced Features

Table 1-13 Power menu options

Power Saving Mode Hard Disk Video Standby Auto Suspend

Disabled Off Off Off Off
Customized Off Off 4 Minutes 15 Minutes
Maximum Power Savings 30 Seconds 2 Minutes 1 Minute 5 Minutes
Maximum Performance Off Off Off 15 Minutes

Table 1-14 Preset values for each Power Saving Modes

Allows editing of advanced power
management features.

87

1.4.1 Power - Advanced Features Modes

Main Advanced Security Power Boot Info Exit

PhoenixBIOS Setup Utility

Advanced Features

Item Specific Help

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-Menu F10Save and Exit

Setup Item

Suspend/Resume
Switch

Lid Closure Suspend

Lid Open Resume

Resume on LAN

Serial Mouse Activity

Suspend/Resume Switch: [Enabled]
Lid Closure Suspend: [On]
Lid Open Resume: [On]
Resume On LAN: [Off]
Serial Mouse Activity: [Disabled]

Figure 1-15 Power - Advance Features menu

Selections

Disabled

Note (Item Specific Help)

Set the SUS/RES Switch.

Enabled
Off

Set the Lid Closure Suspend.

On
Off

Set the Lid Open Resume.

On
Off

On

Turning this feature on will wake the system

up when the internal LAN device receive a

Magic Packet in Suspend Mode.

Disabled
Enabled

T urning this feature on will w ake the video up

from standby mode when external serial

connector activity is detected.

Configures the
Suspend/Resume
switch.

88

Table 1-15 Power - Advanced Features menu options

1.5 Boot Menu

:Boot Device Priority

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-MenuF10Save and Exit

Setup Item

QuickBoot Mode

Boot-time Diagnostic
Screen

Main Advanced Security Power Boot Info Exit

Quick Boot: [Enabled]
Boot Time Diagnostic Screen: [Disabled]

Preboot Execution Environment:[Disabled]

PhoenixBIOS Setup Utility

Item Specific Help

[Disabled]
All diagnostic test
will be done.

[Enabled]
Some diagnostic tests
may be skipped while
booting to speed up.

[Auto]
Diagnostic tests will
be automatically
skipped or done
according to the
order of the ACPI OS.

Figure 1-16 Boot menu

Selections

Disabled
Enabled
Auto

Disabled

Note (Item Specific Help)

S

Allows the system to skip certain tests while
booting. This will decrease the time needed
to boot the system.

Display the diagnostic screen during boot.

S

Enabled

SECTION 3

Boot Device Priority

Select the search order for the types of boot
devices.

Table 1-16 Boot menu options

89

1.5. 1 Boot - Boot Device Priority Menu

Main Advanced Security Power Boot Info Exit

ATAPI CD-ROM Drive
Floppy Disk Drive

+Hard Disk Drive

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-MenuF10Save and Exit

PhoenixBIOS Setup Utility

Boot Device Priority

Figure 1-17 Boot - Boot Device Priority menu

Setup Item

Bootable devices available are listed. The
following devices will appear depending on
the hardware configuration.

[Floppy Disk Drive]
[Hard Drive]
[ATAPI CD-ROM Drive]

Table 1-17 Boot - Boot menu DevicePriority options

Item Specific Help

The top device has
the highest priority.

<Enter> expands or
collapses devices
with a + or -.
<Ctrl+Enter> expands
all.
<›> or <fl> select a
device.
<+>/<Space> or <->
move the device up or
down.
<Shift+1> enables or
disables adevice.

Note (Item Specific Help)

Use <›> or <fl> to select a device, then press

<+> or <Space> to move it up the list, or <–>

to move it down the list. Press <Esc> to exit

this menu.

1.5. 1.1 Boot Menu at POST

The following pop up menu will appear when you hit the Esc k ey during POST. The de vice list in this
pop up menu are same as the list in the Boot Device Priority menu.

Boot Menu

1. Floppy Disk Drive

2. Hard Drive

3. ATAPI CD-ROM Drive

<Enter Setup>

90

1.6 Info Menu

Information Item

BIOS Version

Main Advanced Security Power Boot Info Exit

BIOS Version: 1.XX
BIOS Date: MM/DD/YYYY
BIOS Area: XXXXh - FFFFh

CPU Type:
CPU Speed: XXX MHz
L1 Cache: XX KB
L2 Cache: XXX KB

Total Memory: XX MB

Memory Slot: 64 MB SDRAM

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-MenuF10Save and Exit

PhoenixBIOS Setup Utility

Item Specific Help

Pentium(R) III processor

Figure 1-18 Info menu

Values

Note

n.nn

SECTION 3

BIOS Date
BIOS Area
CPU T ype
CPU Speed
L1 Cache
L2 Cache
Total Memory
Memory Slot

MM/DD/YYYY
xxxxh – FFFFh
Pentium(R) III processor
XXX MHz
32 KB
256KB
64 MB to 256 MB
XX MB SDRAM

Table 1-18 Info menu items

This area can not be used as UMB.

Pentium(R) III processor

91

1.7 Exit menu

Main Advanced Security Power Boot Info Exit

Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes

F1 Help ›fl Select Item -/Space Change Value F9 Setup Defaults
ESCExit ‹fi Select Menu Enter Select :Sub-MenuF10Save and Exit

Setup Item

Exit Saving Changes

Exit Discarding Changes

Load Setup Defaults

PhoenixBIOS Setup Utility

Figure 1-19 Exit menu

Note (Item Specific Help)

Exit System Setup and save your changes to

CMOS.

Exit utility without saving Setup data to CMOS.

Load default values for all SETUP items.

Item Specific Help

Exit System Setup and
save your changes to
CMOS.

Discard Changes

Save Changes

92

Load previous values from CMOS for all

SETUP items.

Save Setup Data to CMOS.

Table 1-19 Exit menu options