Fujitsu Lifebook C2240 User's Guide

Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document. However, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes.

Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited.

The following are registered trademarks of Microsoft Corporation: MS, MS-DOS, Windows.

PCMCIA is a trademark of the Personal Computer Memory Card International Association.

Intel and Pentium are registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.

Adobe Acrobat Reader is a registered trademark of Adobe System Inc.

EarthLink is a registered trademark of EarthLink Network, Inc.

Atheros is a registered trademark of Atheros Communications Inc.

Quicken® is a registered trademark of Intuit, Inc.

Sony MiniDisc and Memory Stick are trademarks of Sony Electronics, Inc.

RADEON is a trademark of ATI Technologies, Inc.

Philips is a trademark of Koninklijke Philips Electronics N.V.

PowerQuest and Drive Image are registered trademarks of PowerQuest Corporatio n.

Netscape 7.0 is a registered trademark of Netscape Communications Corporation.

Norton AntiVirus is a registered trademark of Symantec Corporation.

WinDVD and WinDVD Creator are trademarks of InterVideo, Inc.

The DVD player found in some models of the LifeBook notebook incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights users. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Dolby Headphone manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories. Copyrights 1992-1999 Dolby Laboratories. All rights reserved.

All other trademarks mentioned herein are the property of their respective owners.

Warnin g

Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.

Wash hands after handling.

© Copyright 2003 Fujitsu Computer Systems Corporation. All rights reserved. No part of this publication may be copied, reproduced, translated, stored or transmitted in any electronic form without the written consent of Fujitsu Computer Systems Corporation.

B6FH-0391-01EN-00

DECLARATION OF CONFORMITY

according to FCC Part 15

Responsible Party Name: Fujitsu Computer Systems Corporation

Address: 1250 E. Arques Avenue, M/S 122

Telephone: (408) 982-9500

Declares that product: Model Configurations:

This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions:

(1) This device must not be allowed to cause harmful interference, (2) This device must accept any

interference received, including interference that may cause undesired operation.

Sunnyvale, CA 94085

LifeBook C2230 notebook complies with Part 15 of the FCC Rules.

LifeBook C Series Notebook

Fujitsu LifeBook® C Series notebook

Table of Contents

PREFACE

Preface

About This Guide. . . . . . . . . . . . . . . . . . . . . . . . . 3

Fujitsu Contact Information . . . . . . . . . . . . . . . . . 3

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

GETTING TO KNOW YOUR COMPUTER

Overview

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Locating the Controls and Connectors

Top and Front Components . . . . . . . . . . . . . . . . . 8

Left-Side Panel Components . . . . . . . . . . . . . . . . 9

Right-Side Panel Components . . . . . . . . . . . . . . 10

Back/Top Panel Components . . . . . . . . . . . . . . . 11

Bottom Components . . . . . . . . . . . . . . . . . . . . . 12

Keyboard

Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . 15

Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . 15

Windows Keys. . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Volume Control

Controlling the Volume . . . . . . . . . . . . . . . . . . . 17

Touchpad Pointing Device

Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Double-Clicking. . . . . . . . . . . . . . . . . . . . . . . . . 18

Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Scrolling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Touchpad Control Adjustment. . . . . . . . . . . . . . 19

LifeBook Application Panel

Selector Switch . . . . . . . . . . . . . . . . . . . . . . . . . 20

Application Launch/Media Player Buttons . . . . . 20

Configuring your LifeBook Application Panel . . . 20

Using the Media Player . . . . . . . . . . . . . . . . . . . 21

Desktop Control Panel. . . . . . . . . . . . . . . . . . . . 21

Status Indicator Panel

Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 13

AC Adapter Indicator . . . . . . . . . . . . . . . . . . . . . 13

Battery Level Indicator . . . . . . . . . . . . . . . . . . . . 13

Battery Charging Indicator . . . . . . . . . . . . . . . . . 14

Optical Drive Access Indicator . . . . . . . . . . . . . . 14

Hard Drive Access Indicator . . . . . . . . . . . . . . . . 14

Floppy Drive Access Indicator. . . . . . . . . . . . . . . 14

PC Card Access Indicators . . . . . . . . . . . . . . . . . 14

NumLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . 14

CapsLock Indicator. . . . . . . . . . . . . . . . . . . . . . . 14

ScrLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 14

GETTING STARTED

Power Sources

Connecting the Power Adapters . . . . . . . . . . . . 25

Display Panel

Opening the Display Panel. . . . . . . . . . . . . . . . . 26

Adjusting Display Panel Brightness. . . . . . . . . . . 26

Closing the Display Panel. . . . . . . . . . . . . . . . . . 26

LifeBook C Series Notebook

Starting Your LifeBook Notebook

Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . .27

BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . .27

Booting the System . . . . . . . . . . . . . . . . . . . . . . .28

Windows Product Activation. . . . . . . . . . . . . . . .28

Registering Your LifeBook notebook . . . . . . . . . .29

Installing Click Me! . . . . . . . . . . . . . . . . . . . . . . .29

Power Management

Power/Suspend/Resume Button . . . . . . . . . . . . .30

Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . .30

Hibernation (Save-to-Disk) Feature . . . . . . . . . . .30

Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . .31

Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . .31

Windows Power Management . . . . . . . . . . . . . .31

Restarting the System . . . . . . . . . . . . . . . . . . . . .31

Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

USER-INSTALLABLE FEATURES

Lithium ion Battery

Recharging the Batteries . . . . . . . . . . . . . . . . . . .35

Replacing the Battery . . . . . . . . . . . . . . . . . . . . .36

Internal Floppy Disk Drive

Loading a Disk. . . . . . . . . . . . . . . . . . . . . . . . . . .37

Ejecting a Disk. . . . . . . . . . . . . . . . . . . . . . . . . . .37

Preparing a Disk for Use . . . . . . . . . . . . . . . . . . .37

Optical Drive

Media Player Software . . . . . . . . . . . . . . . . . . . .38

Loading Media on Your Drive . . . . . . . . . . . . . . .39

Removing Media. . . . . . . . . . . . . . . . . . . . . . . . .39

Using the Media Player Software. . . . . . . . . . . . .39

Using Dolby™ Headphone . . . . . . . . . . . . . . . . .40

Using Optical Drive on Battery Power . . . . . . . . .40

Memory Stick/Secure Digital Slot

Installing Memory Stick/SD Cards . . . . . . . . . . . .41

Removing A Memory Stick/SD Card . . . . . . . . . .41

PC Cards

Installing PC Cards . . . . . . . . . . . . . . . . . . . . . . . 43

Removing PC Cards . . . . . . . . . . . . . . . . . . . . . . 43

Memory Upgrade Module

Installing a Memory Upgrade Module. . . . . . . . . 44

Removing a Memory Upgrade Module . . . . . . . . 45

Checking the Computer Recognition

of New Memory Capacity . . . . . . . . . . . . . . . . 45

Device Ports

Modem (RJ-11) Telephone Jack . . . . . . . . . . . . . 46

Internal LAN (RJ-45) Jack . . . . . . . . . . . . . . . . . . 46

IEEE 1394 Port . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Universal Serial Bus Port . . . . . . . . . . . . . . . . . . . 46

Parallel Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Microphone Jack. . . . . . . . . . . . . . . . . . . . . . . . . 46

Optical Digital Audio-Out Connector . . . . . . . . . 47

Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . 47

S-Video Out Port . . . . . . . . . . . . . . . . . . . . . . . . 47

External Monitor Port . . . . . . . . . . . . . . . . . . . . . 47

Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Infrared Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

USING THE INTEGRATED WIRELESS LAN

Before Using the Wireless LAN

For better communications . . . . . . . . . . . . . . . . . 53

Stopping transmission . . . . . . . . . . . . . . . . . . . . . 53

Starting Transmission . . . . . . . . . . . . . . . . . . . . . 54

Connection using Windows XP

Flow of operations . . . . . . . . . . . . . . . . . . . . . . . 55

Preparation for wireless LAN connection . . . . . . . 55

Connection to the network . . . . . . . . . . . . . . . . .57

Connection using Windows 2000

Flow of operations . . . . . . . . . . . . . . . . . . . . . . . 60

Preparation for wireless LAN connection . . . . . . . 60

Connection to the network . . . . . . . . . . . . . . . . .61

Optical Digital Audio Out

Connecting an Optical Digital Cable . . . . . . . . . .42

Troubleshooting the WLAN

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 64

Table of Contents

Wireless LAN Glossary

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

IP address information

Additional information . . . . . . . . . . . . . . . . . . . . 69

Specifications

Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

TROUBLESHOOTING

Troubleshooting

Identifying the Problem . . . . . . . . . . . . . . . . . . . 73

Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . 73

Troubleshooting Table . . . . . . . . . . . . . . . . . . . . 74

Power On Self Test Messages . . . . . . . . . . . . . . 82

Emergency Optical Drive Tray Release . . . . . . . . 83

Modem Result Codes. . . . . . . . . . . . . . . . . . . . . 83

Restoring Your Pre-installed Software . . . . . . . . 84

Drive Image Special Edition (DISE) . . . . . . . . . . . 84

SPECIFICATIONS

Specifications

Configuration Label . . . . . . . . . . . . . . . . . . . . . . 95

Microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . 95

Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Mass Storage Device Options . . . . . . . . . . . . . . 95

Integrated Pointing Device. . . . . . . . . . . . . . . . . 96

Communications . . . . . . . . . . . . . . . . . . . . . . . . 96

LifeBook Application Panel. . . . . . . . . . . . . . . . . 96

Theft Prevention Lock Slot . . . . . . . . . . . . . . . . . 96

Device Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Dimensions and Weight. . . . . . . . . . . . . . . . . . . 96

Environmental Requirements . . . . . . . . . . . . . . . 96

Pre-Installed Software . . . . . . . . . . . . . . . . . . . . 97

Regulatory Information . . . . . . . . . . . . . . . . . . . 99

CARE AND MAINTENANCE

Care and Maintenance

LifeBook Notebook . . . . . . . . . . . . . . . . . . . . . . 89

Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Floppy Disks and Drives . . . . . . . . . . . . . . . . . . . 90

Media Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

GLOSSARY

Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

INDEX

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

LifeBook C Series Notebook

Preface

LifeBook C Series Notebook

Preface

ABOUT THIS GUIDE

The LifeBook® C Series notebook from Fujitsu is an allin-one notebook featuring the Intel® Pentium® 4 processor and an ATI® RADEON™ IGP 340M graphics chip with support for up to 128 MB of shared memory. This combination delivers the resources to tackle video editing, computer gaming, and general business applications. A large and bright 15-inch display adds to the computing experience, bringing applications to life wherever you are.

This manual explains how to operate your LifeBook notebook’s hardware and built-in system software.

Your LifeBook notebook comes with Microsoft® Windows XP Home, Windows XP Professional, or Windows 2000 pre-installed.

The LifeBook notebook is a completely self-contained unit with an active-matrix (TFT) color LCD display. It has a powerful interface that enables it to support a variety of optional features.

Conventions Used in the Guide

Keyboard keys appear in brackets. Example: [Fn], [F1], [ESC], [ENTER] and [CTRL].

Pages with additional information about a specific topic are cross-referenced within the text. Example: (See page xx.)

On screen buttons or menu items appear in bold Example: Click OK to restart your notebook computer.

DOS commands you enter appear in Courier type. Example: Shut down the computer?

FUJITSU CONTACT INFORMATION

Service and Support

You can contact Fujitsu Service and Support in the following ways:

■

Toll free: 1-800-8Fujitsu (1-800-838-5487)

■

Fax: 408-764-2724

■

E-mail: 8fujitsu@us.fujitsu.com/computers

■

Web site: http://us.fujitsu.com/computers

Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:

■

Product name

■

Product configuration number

■

Product serial number

■

Purchase date

■

Conditions under which the problem occurred

■

Any error messages that have occurred

■

Hardware configuration

■

Type of device connected, if any

Fujitsu Online

You can go directly to the online Fujitsu product catalog for your LifeBook notebook by clicking on the LifeBook Accessories web site link, located in the Windows Start menu.

You can also reach Fujitsu Service and Support on-line by clicking on the Fujitsu Service and Support Web site link, located in the Service and Support Software folder

of the Windows Start menu.

You must have an active internet connection to use the online URL links.

The information icon highlights information that will enhance your understanding of the subject material.

The caution icon highlights information that is important to the safe operation of your computer, or to the integrity of your files. Please read all caution information carefully.

The warning icon highlights information that can be hazardous to either you, your LifeBook T Series Tablet PC, or your files. Please read all warning information carefully.

WARRANTY

Your LifeBook notebook is backed by a one year International Limited Warranty. Check the service kit that came with your LifeBook notebook for warranty terms and conditions.

LifeBook C Series Notebook – Section One

Getting to Know Your Computer

LifeBook C Series Notebook – Section Two

Figure 2-1. LifeBook C Series notebook

Overview

This section describes the components of your LifeBook notebook. We strongly recommend that you read it before using your notebook – even if you are already familiar with notebook computers.

UNPACKING

When you receive your LifeBook notebook, unpack it carefully, and compare the parts you have received with the items listed below.

For a pre-configured model you should have:

■

LifeBook C Series notebook (Figure 2-1)

■

Lithium ion battery, pre-installed

■

AC adapter with AC power cord (Figure 2-2)

■

Phone/Modem (RJ-11) telephone cable

■

Drivers and Applications CD

■

Getting Started Guide

■

User’s Guide (this document)

■

Premium Care registration information

■

International Limited Warranty Brochure

■

Microsoft-associated product materials

Depending upon the configuration of your notebook, you may have also received one of the following items:

■

WinDVD® 4/WinDVD Creator™ Plus and RecordNow™

■

WinDVD® 4/RecordNow™

■

WinDVD® 4

■

An additional main battery

Once you have checked and confirmed that your LifeBook notebook system is complete, read through the following pages to learn about all of your notebook’s components.

Detailed specifications about your LifeBook notebook can be found in the chapter entitled “Specifications” on page 95.

Figure 2-2. Typical AC Adapter

LifeBook C Series Notebook – Section Two

Display Panel Latch

Display

Power/

Keyboard

LifeBook Application Panel

Status Indicator Panel

Stereo Speaker

Touchpad

Scroll Button

Selector Switch

Closed Cover Switch

Panel

Suspend/ Resume Button

Figure 2-3. LifeBook notebook with display open

Locating the Controls and Connectors

TOP AND FRONT COMPONENTS

The following is a brief description of your LifeBook notebook’s top and front components. (Figure 2-3)

Display Panel Latch

The display panel latch locks and releases the display panel.

Display Panel

The display panel is a color LCD panel with back lighting for the display of text and graphics. (See Display

Panel on page 26 for more information.)

Closed Cover Switch

The closed cover switch suspends the system when the cover is closed.

LifeBook Application Panel

The LifeBook Application Panel allows you to either launch your favorite applications by the touch of a button or to use as a media player when your unit is on.

(See LifeBook Application Panel on page 20 for more information.)

Status Indicator Panel

The Status Indicator Panel displays symbols that correspond with a specific component of your LifeBook notebook. (See Status Indicator Panel on page 13 for more

information.)

Power/Suspend/Resume Button

The Power/Suspend/Resume button allows you to suspend notebook activity without powering off, resume your notebook from suspend mode, and power on your notebook when it has been shut down from Windows.

(See Power/Suspend/Resume Button on page 30 for more information.)

Stereo Speakers

The built-in boxless dual speakers provide stereo sound.

Keyboard

A full-size keyboard with dedicated Windows keys.

(See Keyboard on page 15 for more information.)

Touchpad Pointing Device/Scroll Button

The Touchpad pointing device is a mouse-like cursor control with three buttons (left, right, and scroll buttons). (See Touchpad Pointing Device on page 18 for

more information.)

Locating the Controls and Connectors

PC Card

PC Card Eject Buttons

Anti-Theft Lock Slot

DC Power Jack

S-Video Out Port

Memory Stick/ SD Card Slot

Modem Jack

Slots

IEEE 1394 (4-pin) Port

Figure 2-4. LifeBook notebook left-side panel

LEFT-SIDE PANEL COMPONENTS

The following is a brief description of your LifeBook notebook’s left-side components. (Figure 2-4)

Modem (RJ-11) Telephone Jack

The Modem (RJ-11) telephone jack is for attaching a telephone line to the internal 56K modem. (See Modem (RJ-

11) Telephone Jack on page 46 for more information.)

■

The internal modem is designed to the ITU-T V.90 standard. Its maximum speed of 53000bps is the highest allowed by FCC, and its actual connection rate depends on the line conditions. The maximum speed is 33600bps at upload.

■

The internal modems on all LifeBook notebooks from are certified for use in the United States and Canada. The modem may be certified in other countries.

The internal modem is not intended for use with Digital PBX systems. Do not connect the internal modem to a Digital PBX as it may cause serious damage to the internal modem or your entire LifeBook notebook. Consult your PBX manufacturer’s documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem.

S-Video Out Port

The S-Video output is used to transmit a higher resolution video signal to a compatible TV or VCR.(See S-Video

Out Port on page 47 for more information.)

Memory Stick/SD Card Slot

The Memory Stick/Secure Digital (SD) card slot allows you to install a flash memory card for data storage. This architecture allows you to transfer data between a variety of different digital devices. (See Installing Memory Stick/

SD Cards on page 41 for more information.)

Anti-theft Lock Slot

The anti-theft lock slot allows you to attach an optional physical lock-down device.

PC Card Slots

The PC Card Slots allow you to install two Type I/II PC Cards or one Type III PC Card. (See PC Cards on page 43

for more information.)

IEEE 1394 (4-pin) Port

The 1394 port is used to connect between your LifeBook notebook and a peripheral such as a digital video camera.(See IEEE 1394 Port on page 46 for more informa- tion.)

DC Power Jack

The DC power jack allows you to plug in the AC adapter or the optional Auto/Airline adapter to power your LifeBook notebook and charge the internal Lithium ion battery.

LifeBook C Series Notebook – Section Two

Microphone

Internal Floppy Disk Drive

Media Player

Emergency Media Player Tray Release

USB 2.0 Port

Eject Button

Infrared Port

Wireless LAN Switch (on wireless LAN models only)

Optical Digital Audio-Out/ Headphone Jack

(3 additional USB 2.0 ports on back of system)

Jack

Figure 2-5. LifeBook notebook right-side panel

RIGHT-SIDE PANEL COMPONENTS

The following is a brief description of your LifeBook notebook’s right-side components. (Figure 2-5)

Optical Digital Audio-Out/Headphone Jack

When used as an optical digital audio-out, this jack allows you to download digital audio onto a MiniDisc recorder’s SPDIF (Sony Philips Digital Interface) format.

(See Optical Digital Audio-Out Connector on page 47 for more information.). When used as a headphone jack, this

jack allows you to connect headphones or powered external speakers. (See Headphone Jack on page 47 for

more information.)

Microphone Jack

The microphone jack allows you to connect an external mono microphone. (See Microphone Jack on page 46 for

more information.)

Media Player Eject Button

The media player Eject Button allows you to open the media player tray to remove or install a DVD, CD-R, or CD-ROM. (See Optical Drive on page 38 for more infor-

mation.)

Media Player

The media player allows you to play back a media disc.

(See Optical Drive on page 38 for more information.)Emergency Media Player Tray Release

The Emergency Media Player Tray Release allows you to open the media player tray without powering on your LifeBook notebook.

Infrared Port

The fast IrDA-compatible port allows you to communicate with another IrDA-compatible infrared device without a cable.

USB 2.0 Port

The USB port allows you to connect Universal Serial Bus

2.0 or USB 1.1 devices. Note that there are three additional USB 2.0 ports on the rear of the system. (See

Universal Serial Bus Port on page 46 for more information.)

Internal Floppy Disk Drive

A standard floppy disk drive to accommodate 3.5” floppy disks. ((See Internal Floppy Disk Drive on page 37

for more information.)

Wireless LAN Switch

The Wireless LAN Switch turns the optional wireless LAN on and off. (See Integrated Wireless LAN* User’s

Guide on page 91 for more information.)

■

The media player that your LifeBook

notebook uses is determined by the configuration of your system.

■

The terms “media” and “media disc” in

this document refer to any of the possible media drives or media discs available for your notebook (i.e., DVD, DVD-RW, CD-ROM, CD-R, or CDRW).

Figure 2-6. LifeBook notebook back/top panel

Parallel Port

LAN Jack (RJ-45)

USB Ports (Qty. 3)

External Monitor Port

Serial Port

Wireless LAN Antenna Compartment

BACK/TOP PANEL COMPONENTS

The following is a brief description of your LifeBook notebook’s back panel components. (Figure 2-6)

USB Ports

The four USB 2.0 ports (three on the rear, one on the right side) allow you to connect Universal Serial Bus devices. (See Universal Serial Bus Port on page 46 for more

information.)

Locating the Controls and Connectors

LAN Jack (RJ-45)

The LAN jack is designed to accept a Local Area Network (LAN) RJ-45 plug. (See Internal LAN (RJ-45) Jack on

page 46 for more information.)

Serial Port

The serial port allows you to connect serial RS-232 devices, such as serial printers or serial scanners.

Parallel Port

The parallel port allows you to connect parallel devices, such as a printer. (This is also sometimes referred to as an LPT port.) (See Parallel Port on page 46 for more informa-

tion.)

External Monitor Port

The external monitor port allows you to connect an external monitor. (See External Monitor Port on page 47

for more information.)

Wireless LAN Antenna Compartment

The Wireless LAN Antenna compartment houses the antenna for the optional wireless LAN device.

LifeBook C Series Notebook – Section Two

Lithium ion Battery Bay

Main Unit and Configuration Label

Certificate of Authenticity Label (approximate location)

Figure 2-7. LifeBook notebook bottom panel

BOTTOM COMPONENTS

The following is a brief description of your LifeBook notebook’s bottom panel components. (Figure 2-7)

Main Unit and Configuration Label

The configuration label shows the model number and other information about your LifeBook notebook. In addition, the configuration portion of the label has the serial number and manufacturer information that you will need to give your support representative. It identifies the exact version of various components of your LifeBook notebook. (See Configuration Label on page 95

for more information.)

Lithium ion Battery Bay

The battery bay contains the internal Lithium ion battery. It can be opened for the removal of the battery when stored over a long period of time or for swapping a discharged battery with a charged Lithium ion battery.

(See Lithium ion Battery on page 35 for more information.)

Figure 2-8 Status Indicator Panel

Power AC Adapter Battery

Level

Hard Floppy

PC Card Access

NumLk CapsLk ScrLk

Optical

Drive

Access

Drive Access

76%–100% Charging

76%–100%

51%–75%

26%–50%

11%–25%

Low Warning <11%

Critical Low or Dead Battery

Shorted Battery

Status Indicator Panel

The Status Indicator displays symbols that correspond with a specific component of your LifeBook notebook. These symbols (when visible) tell you how each of those components is operating. (Figure 2-8)

POWER INDICATOR

The Power indicator symbol states whether your system is operational. It has several different states, each of which tells you what mode your LifeBook notebook is in at that time.

■

Steady On: This means that there is power to your LifeBook notebook and that it is ready for use.

■

Flashing: This means that your LifeBook notebook is in Suspend mode.

■

Steady Off (not visible): This means that your system is either in Save-to-Disk mode, or that your LifeBook notebook has been turned off.

If you are charging your battery, the Power indicator symbol will remain on even if your LifeBook notebook is shut off. The Power indicator symbol will also remain on if you have either adapter connected and are shut down from Windows, but have not turned off the power.

AC ADAPTER INDICATOR

The AC Adapter indicator states whether your LifeBook notebook is operating from the AC adapter, the Auto/ Airline adapter or the batteries. This icon has two different states that can tell you what power source your LifeBook notebook is using.

■

On: This means that either of the adapters are currently in use.

■

Off: Power is only coming from the batteries, and you do not have an adapter connected.

BATTERY LEVEL INDICATOR

The Battery Level indicator states whether or not the primary Lithium ion battery is installed. In addition, this symbol states how much charge is available within the battery. The symbol will only be displayed for a battery that is currently installed in your LifeBook notebook. (Figure 2-9)

Figure 2-9 Battery Level Indicator

A shorted battery is damaged and must be replaced.

If there is no battery activity or the power adapters are not connected, the Battery Level indicator will also be off.

(Figure 2-9)

LifeBook C Series Notebook – Section Two

BATTERY CHARGING INDICATOR

Located to the left of the Battery Level indicator is a small arrow symbol. This symbol indicates whether the

battery is charging or not.

Batteries subjected to shocks, vibration or extreme temperatures can be permanently damaged.

OPTICAL DRIVE ACCESS INDICATOR

The Optical Drive access indicator tells you that the optical drive is being accessed. If the Auto Insert Notification function is active, the indicator will flash periodically when your system is checking the media player drive. If the Auto Insert Notification function is not active, the indicator will only flash when you access the optical drive. The default setting is the Auto Insert Notification function active.

HARD DRIVE ACCESS INDICATOR

The Hard Drive Access indicator states whether your internal hard drive is being accessed.

1 2

PC CARD ACCESS INDICATORS

The PC Card Access indicators state whether or not your LifeBook notebook is accessing a PC Card. The indicators will flash if your software tries to access a PC Card even if there is no card installed. The first indicator represents the built-in PC card slot; the second indicates when a modular PC Card slot is installed. (See PC Cards

on page 43 for more information)

NUMLK INDICATOR

The NumLk indicator states that the internal keyboard is set in ten-key numeric keypad mode.

If you are using the optional external numerical keypad, pressing the [NumLk] key will activate the external keypad. The indicator will come on, however it will not change any of the functionality of your keyboard keys.

CAPSLOCK INDICATOR

The CapsLock indicator states that your keyboard is set to type in all capital letters.

FLOPPY DRIVE ACCESS INDICATOR

The Floppy Drive Access indicator states whether the internal floppy disk drive is being accessed. This indicator will flash if your software tries to access a disk even if no floppy disk drive is installed. (See Internal Floppy

Disk Drive on page 37 for more information)

SCRLK INDICATOR

The ScrLk indicator states that your scroll lock is active.

Fn Key Start Key

Function Keys

Numeric Keypad Cursor Keys

Application Key

(outlined with thick black line)

Figure 2-10. Keyboard

Keyboard

USING THE KEYBOARD

Your LifeBook notebook has an integral 87-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys. This section describes the following keys.

■

Numeric keypad

■

Cursor keys

■

Function keys

■

Windows keys

NUMERIC KEYPAD

Certain keys on the keyboard perform dual functions as both standard character keys and numeric keypad keys. NumLk can be activated by pressing the [NumLk] keys. Turning off the NumLk feature is done the same way. Once this feature is activated you can enter numerals 0 through 9, perform addition ( + ), subtraction ( - ), multiplication ( * ), or division ( / ), and enter decimal points ( . ) using the keys designated as ten-key function keys. The keys in the numeric keypad are marked on the front edge of the key to indicate their secondary functions.

WINDOWS KEYS

Your LifeBook notebook has two Windows keys, consisting of one Start key and one Application key. The Start key displays the Start menu. This button functions the same as your on-screen Start menu button. The Application key functions the same as your right mouse button and displays shortcut menus for the selected item. (Refer to your Windows documentation for additional information regarding the Windows keys.)

CURSOR KEYS

The cursor keys are the four arrow keys on the keyboard which allow you to move the cursor up, down, left and right in applications. In programs such as Windows Explorer, it moves the “focus” (selects the next item up, down, left, or right).

LifeBook C Series Notebook – Section Two

FUNCTION KEYS

Your LifeBook notebook has 12 function keys, F1 through F12. The functions assigned to these keys differ for each application. You should refer to your software documentation to find out how these keys are used.

The [Fn] key provides extended functions for the LifeBook notebook and is always used in conjunction with another key.

■

[Fn+F3]: Pressing [F3] while holding [Fn] will toggle the Audio Mute on and off.

■

[Fn+F4]: Pressing [F4] while holding down [Fn] allows you to toggle between an internal mouse (touchpad) and an external mouse (USB-type).

■

[Fn+F5]: Pressing [F5] while holding [Fn] allows you to toggle between video compensation and no compensation. (Video compensation controls spacing on the display. When it is enabled, displays with less than 1024 x 768 or 800 x 600 pixel resolution will still cover the entire screen.)

■

[Fn+F6]: Pressing [F6] repeatedly while holding [Fn] will lower the brightness of your display.

■

[Fn+F7]: Pressing [F7] repeatedly while holding [Fn] will increase the brightness of the display.

■

[Fn+F8]: Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your LifeBook notebook.

■

[Fn+F9]: Pressing [F9] repeatedly while holding [Fn] will increase the volume of your LifeBook notebook.

■

[Fn+F10]: Pressing [F10] while holding [Fn] allows you to change your selection of where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order, are: built-in display panel only, both built-in display panel and external monitor or external monitor only.

Volume Control

Your LifeBook notebook has multiple volume controls

which interact with each other.

■

Any software that contains audio files will also contain a volume control of its own. If you install an external audio device that has an independent volume control, the hardware volume control and the software volume control will interact with each other. It should be noted that if you set your software volume to Off, you will override the external volume control setting.

■

Using the Fn+F8 and Fn+F9 combinations to control volume will override software volume controls.

CONTROLLING THE VOLUME

The volume can be controlled in several different ways:

■

Volume can be set from within the Volume Control on the Taskbar.

■

Volume can be controlled with the [F8] and [F9] functions keys. Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your notebook. Pressing [F9] repeatedly while holding [Fn] will increase the volume of your notebook.

■

Volume can be controlled by many volume controls that are set within individual applications.

■

Certain external audio devices you might connect to your system may have hardware volume controls.

Volume Control

Each source discussed above puts an upper limit on the volume level that must then be followed by the other sources.

We recommend that you experiment with the various volume controls to discover the optimal sound level.

LifeBook C Series Notebook – Section Two

Touchpad

Left

Scroll

Right Button

Button

Figure 2-11. Touchpad pointing device

Touchpad Pointing Device

The Touchpad pointing device comes built into your LifeBook notebook. It is used to control the movement of the pointer to select items on your display panel. The Touchpad is composed of a cursor control, a left and right button, and a scrolling button. The cursor control works the same way a mouse does, and moves the cursor around the display. It only requires light pressure with the tip of your finger. The left and right buttons function the same as mouse buttons. The actual functionality of the buttons may vary depending on the application that is being used. The scrolling button allows you to navigate quickly through pages, without having to use the scroll bars. (Figure 2-11)

CLICKING

Clicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it. To right-click, move the mouse cursor to the item you wish to select, press the right button once, and then immediately release it. You can also perform the clicking operation by tapping lightly on the To u ch pad o nce. (Figure 2-12)

Figure 2-12. Clicking

DOUBLE-CLICKING

Double-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, press the left button twice, and then immediately release it. You can also perform the double-click operation by tapping lightly on the Touchpad twice. (Figure 2-13)

Figure 2-13. Double-clicking

Touchpad Pointing Device

■

If the interval between clicks is too

long, the double-click will not be executed.

■

Parameters for the Touchpad can be adjusted from the Mouse Properties dialog box located in the Windows Control Panel.

DRAGGING

Dragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it. Dragging can also be done using the Touchpad. First, tap the Touchpad twice over the item you wish to move making sure to leave your finger on the pad after the final tap. Next, move the object to its new location by moving your finger across the Touchpad, and then releasing your finger. (Figure 2-14)

SCROLLING

Using the Scrolling button allows you to navigate through a document quickly without using the window’s scroll bars. This is particularly useful when you are navigating through on-line pages. To use the Scrolling button, press the crescent shape at the top or bottom of the button to scroll up or down a page. When you have reached the desired section of the page, release the button. (Figure 2-15)

Figure 2-15. Scrolling

TOUCHPAD CONTROL ADJUSTMENT

If you need to change or adjust any of the touchpad control functions, you can customize them from the Mouse properties dialog box in the Control Panel. Click on Start, select Settings > Control Panel, then doubleclick Mouse.

Figure 2-14. Dragging

LifeBook C Series Notebook – Section Two

Selector Switch

Application Launcher Buttons

Figure 2-16. LifeBook Application Launcher Buttons

LifeBook Application Panel

A unique feature of your LifeBook notebook is the LifeBook Application Panel. The LifeBook Application Panel system makes your LifeBook notebook more than just another notebook computer. This panel allows you to operate the optical drive as an independent audio media player or to launch applications with the touch of one

button.

■

The LifeBook Application Panel uses the

date and time settings of your LifeBook notebook. If the date and time are incorrect, you can adjust the settings in the Windows Control Panel.

■

The media player that your LifeBook

notebook uses is determined by the configuration of your system.

Your LifeBook notebook is pre-installed with software utilities that let you operate and configure your LifeBook Application Panel. These utilities are found under the Start menu -> Control Panel ->Application Panel.

The panel consists of the following elements:

SELECTOR SWITCH

Located at the far left of the panel, this switch allows you to select the function of the panel—either as an Application Launcher, a media player, or as a lock.

The buttons can be locked and unlocked by pressing either of the selector switch positions for four seconds or longer. When the selector switch is in Lock mode, the buttons are disabled and do nothing when pressed.

APPLICATION LAUNCH/ MEDIA PLAYER BUTTONS

When the selector switch is in the Application position, pressing any of the buttons will launch a user-defined application. When the selector switch is in the Media Player position, the buttons operate the media player.

CONFIGURING YOUR LIFEBOOK APPLICATION PANEL

When you start your system, the LifeBook Application Panel is automatically activated. As an application launcher, the LifeBook Application Panel is very flexible, giving you a variety of options. To set up the Panel to best suit your needs, we have provided the Application Panel Setup utility that quickly and easily helps you make the most of this valuable feature.

To configure your LifeBook Application Panel with Application Panel Setup:

1. Click on Start.

2. Click on Control Panel.

3. Double-click on Application Panel.

The Application Panel Setup utility will appear. There are tabs that correspond to the application buttons on the LifeBook Application Panel. When you receive your LifeBook notebook, these buttons are pre-configured to launch specific programs. (See Specifications on page 95

for more information).

The tabs in Application Panel Setup may not be in the same order as the buttons on your LifeBook notebook. Please select the tab you wish to change carefully.

To change an application associated with one of the buttons, click on the tab for the button you would like to reconfigure. Click on the Browse button. Scroll down to

LifeBook Application Panel

the application you want to associate with the buttons, click on the application you wish to launch with this button, and then click Open. Click OK, and the button will now launch the new application.

One of the buttons may be preconfigured to launch your default Internet browser. In order to reconfigure it to launch a different program, follow these easy steps:

1. Click on the Internet tab of the application panel utility. Click on the down-arrow in the Specify the button action: field. Select Start Other Program from the dropdown list.

2. Click on the Browse button.

3. Scroll down the list of applications, and click on the application you wish to launch with this button. Click on Open.

4. Click OK.

The button will now launch the new application. If you want to return to launching your default Internet browser with this button, you need only click on “Default Internet Browser” from the dropdown list. Be aware that you will erase the settings for the “other application”. If you wish to go back to launching the “other application” from this button, you will need to reconfigure it as described above.

The E-mail tab can be modified in the same manner as the Internet tab.

At the bottom of each application setup page are two selectable options. The first will enable/disable the button when your LifeBook notebook is in Standby mode, and the second will enable/disable the button when your LifeBook notebook is in the pseudo-off state. You can enable/ disable either or both of these functions simply by

clicking on the option.

If you choose to have the buttons work when the LifeBook notebook is in standby, they will function even if hit accidentally, and will turn on your LifeBook notebook even if you are not present or using your LifeBook notebook. This could deplete your battery, and you will need to recharge it before using the LifeBook notebook. As a precaution, press the selector switch for four or more seconds to lock the buttons when you are away from your LifeBook notebook. To unlock the buttons, repeat the procedure.

When you have finished with Application Panel utility, click on OK, and the new settings will take effect. You can reconfigure your LifeBook Application Panel as often as you like.

USING THE MEDIA PLAYER

The media player enables you to use your LifeBook note-

book’s optical drive as an audio media player.

■

If you shut down from Windows while the media player is playing an audio CD, it will stop.

■

You cannot go into Suspend Mode or Hibernation (Save-to-Disk) Mode while the media player is playing a CD.

■

The media player will only play when the system is powered on.

There is no configuration required for media player operation. The buttons are pre-configured to work like a normal media player. When the selector switch is in the bottom position, the buttons will operate as follows:

■

Stop/Eject: This is the first button to the right of the Selector switch. If you press it once, it will stop an audio CD that is playing. If you press it twice, it will eject the audio CD.

■

Play/Pause: This is the second button to the right of the Selector switch. Press this button to start playing an audio CD starting at Track 1. While the audio CD is playing, press it to pause. Press it again to continue.

■

If you press the play button and nothing happens, you either have the Selector switch locked, there is no audio CD in the media player drive, you have a CD other than an audio CD in the drive, or system is not powered on.

■

Because of the Windows CD auto-insertion function, audio CDs will start playing immediately after they are inserted if your LifeBook notebook is On. This will not happen if you are using the media player in Suspend or Pseudo-off modes.

■

Fast Backward: This is the third button to the right of the Selector switch. Press this button once to skip one track back.

■

Fast Forward: This is the fourth button to the right of the Selector switch. Press this button once to skip forward one track.

LifeBook C Series Notebook – Section Two

DESKTOP CONTROL PANEL

Your LifeBook notebook includes a desktop control panel for your notebook’s desktop that you can use at any time. You may use this panel to operate the media player when you have the Selector switch in the Application position or Lock mode.

To use the desktop control panel:

1. Click on Start.

2. Click on Programs.

3. Click on Lifebook Application Panel.

4. Click on CD Player.

The desktop control panel will appear in the upper corner of your screen. To close the panel:

1. Click on the “x” button.

To minimize the panel:

2. Click on the “-” button.

You can select from four appearances for your desktop control panel. Simply double-click on the track display area of the panel, and a menu will appear which will allow you to select from a pull down menu. On the same pop-up are two other options: “Always on top” and “Continuous Play”. If you click on “Always on top” the desktop controls will always be seen on your screen, no matter what other application you are running. If you click on “Continuous Play”, your media player will automatically start over at the beginning of the CD in the drive as soon as it finishes the last track.

You can move the desktop control panel to anywhere on your desktop. Drag it by clicking on the track number display, holding it down, and dragging the control panel. When you place it where you would like, release the

mouse button.

Deactivating and Activating the LifeBook Application Panel

To deactivate the LifeBook Application Panel, follow these easy steps:

1. Click on Start.

2. Click on Programs.

3. Click on LifeBook Application Panel.

4. Click on Stop Application Panel.

To reactivate, follow the same procedure, except for

step 4. Click on Start Application Panel instead.

Every time you start Windows, the LifeBook Application Panel is activated, even if you deactivated it before you shut down.

Application Panel Setup

■

If you insert an audio CD which has both audio and data tracks into the media player drive, the media player may fail to play the first audio track.

■

The Volume Up, Volume Down and Mute controls for the media player desktop control panel adjusts the volume of the CD audio line only. It does not adjust your LifeBook notebook’s master software volume control.

■

The media player desktop control panel is designed to be displayed in High Color (16-bit) or in True Color (24-bit or more). If you have your LifeBook notebook’s display set for 256 colors or less Media Player will display in a “basic” mode.

■

If you have your display set to 256

colors, the basic display will appear no matter which one you select. You will need to set your display colors to more than 256 in order to select other display appearances.

■

When you close the media player’s

desktop control panel, it will stop the audio media player. Simply press the Play button if you would like to continue listening, and the media player will restart at track 1. The Selector switch must be in the media player position.

Getting Started

LifeBook C Series Notebook – Section Three

Figure 3-1. Connecting the AC Adapter

AC Cable

AC Adapter

DC Power Jack

DC Output Cable

Power Sources

Your LifeBook notebook has three possible power sources: a primary Lithium ion battery, an AC adapter or an optional Auto/Airline adapter.

CONNECTING THE POWER ADAPTERS

The AC adapter or optional Auto/Airline adapter provides power for operating your LifeBook notebook and charging the batteries.

Connecting the AC Adapter

1. Plug the DC output cable into the DC power jack of your LifeBook notebook.

2. Plug the AC adapter into an AC electrical outlet.

Connecting the Optional Auto/Airline Adapter

1. Plug the DC output cable into the DC power jack on your LifeBook notebook.

2. Plug the Auto/Airline adapter into the cigarette lighter of an automobile with the ignition key in the On or Accessories position.

3. Plug the Auto/Airline adapter into the DC power jack on an airplane seat.

Switching from AC Adapter Power or the Auto/Airline Adapter to Battery Power

1. Be sure that you have at least one charged battery installed.

2. Remove the AC adapter or the Auto/Airline adapter. Your notebook will automatically switch from DC

power to battery power.

The Lithium ion battery is not charged upon purchase. Initially, you will need to connect either the AC adapter or the Auto/Airline adapter to use your LifeBook notebook.

LifeBook C Series Notebook – Section Three

Display Panel Latch

Figure 3-2. Opening the Display Panel

Display Panel

Your LifeBook notebook contains a display panel that is backlit for easier viewing in bright environments and maintains top resolution through the use of activematrix technology. Your system has a 15” SXGA display panel.

OPENING THE DISPLAY PANEL

1. Slide the latch located at the top of the display panel to the right. This releases the locking mechanism and raises the display slightly.

2. Lift the display backwards, being careful not to touch the screen, until it is at a comfortable viewing angle.

ADJUSTING DISPLAY PANEL BRIGHTNESS

Once you have turned on your LifeBook notebook, you may want to adjust the brightness level of the screen to a more comfortable viewing level. There are two ways to adjust the brightness, keyboard and power management

utility.

The higher the brightness level, the more power the LifeBook notebook will consume and the faster your batteries will discharge. For maximum battery life, set the brightness to as low a level as possible.

Using the Power Management Utility (Windows 2000 only)

Adjusting the brightness using the Power Management utility changes the setting permanently.

1. Double-click the BatteryAid icon in the lower right corner of your display. This will open the BatteryAid Properties dialog box.

2. Select the Power Control tab and adjust your LCD Backlighting to the desired level.

3. Click OK or Apply to permanently change the settings.

You may need to readjust the brightness level periodi-

cally, depending on your operating environment.

The higher the brightness level, the more power the notebook will consume and the faster your batteries will discharge. For maximum battery life, make sure that the brightness is set as low as possible.

CLOSING THE DISPLAY PANEL

1. Holding the edge of your display panel, pull it forward until it is flush with the body of your LifeBook notebook.

2. Push down until you hear a click. This will engage the locking mechanism and prevent your display panel from opening unexpectedly.

Keyboard

Adjusting the brightness using the keyboard changes the setting only temporarily.

■

[Fn+F6]: Pressing repeatedly will lower the brightness of your display.

■

[Fn+F7]: Pressing repeatedly will increase the brightness of the display.

Starting Your LifeBook Notebook

POWER ON

Power/Suspend/Resume Button

The Power/Suspend/Resume button is used to turn on your LifeBook notebook from its off state. Once you have connected your AC adapter or charged the internal Lithium ion battery, you can power on your LifeBook

notebook. (See figure 2-3 on page 8 for location)

When you turn on your LifeBook notebook be sure you have a power source. This means that at least one battery is installed and charged, or that the AC or Auto/Airline adapter is connected and has power.

To turn on your LifeBook notebook from its off state, press the Power/Suspend/Resume located above the keyboard. When you are done working you can either leave your LifeBook notebook in Suspend mode, (See Suspend Mode on page 30 for more information), or you can turn it off. (See Power Off on page 31 for more infor-

mation)

Do not carry your LifeBook notebook around with the power on or subject it to shocks or vibration, as you risk damaging your notebook.

When you power on your LifeBook notebook, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your LifeBook notebook will emit an audio warning and/or an error message will be displayed.

(See Power On Self Test Messages on page 82 for more information) Depending on the nature of the problem,

you may be able to continue by starting the operating system or by entering the BIOS setup utility and revising the settings.

After satisfactory completion of the POST, your Life-

Book notebook will load your operating system.

Never turn off your LifeBook notebook during the POST or it will cause an error message to be displayed when you turn your LifeBook notebook on the next time.

(See Power On Self Test Messages on page 82 for more information)

BOOT SEQUENCE

The procedure for starting-up your LifeBook notebook is termed the Bootup sequence and involves your LifeBook notebook’s Basic Input-Output System (BIOS). When your LifeBook notebook is first turned on, the main system memory is empty, and it needs to find instructions to start up your LifeBook notebook. This information is in the BIOS program. Each time you power up or restart your LifeBook notebook, it goes through a boot sequence which displays a Fujitsu logo until your operating system is loaded. During booting, your LifeBook notebook is performing a standard boot sequence including a POST. When the boot sequence is completed without a failure and without a request for the BIOS Setup Utility, the system displays the operating system’s opening screen.

The boot sequence is executed when:

■

You turn on the power to your LifeBook notebook.

■

You restart your LifeBook notebook from the Windows Shut Down dialog box.

■

The software initiates a system restart. Example: When you install a new application.

■

You reset the system by pressing the three keys [CTRL+ALT+DEL].

BIOS SETUP UTILITY

The BIOS Setup Utility is a program that sets up the operating environment for your LifeBook notebook. Your BIOS is set at the factory for normal operating conditions, therefore there is no need to set or change the BIOS’ environment to operate your LifeBook notebook.

The BIOS Setup Utility allows you to:

■

Device control feature parameters, such as changing I/O addresses and boot devices.

■

System data security feature parameters, such as passwords.

Entering the BIOS Setup Utility

To enter the BIOS Setup Utility do the following:

1. Turn on or restart your LifeBook notebook.

2. Press the [F2] key once the Fujitsu logo appears on the screen with a prompt below it. This will open the main menu of the BIOS Setup Utility with the current settings displayed.

3. Press the arrow keys to scroll through the other setup menus to review or alter the current settings.

LifeBook C Series Notebook – Section Three

Changing Video RAM Size

Your system is set up to use 32 MB of video RAM by default, but you can change the allocated amount from within the BIOS. To change the amount of video RAM, perform the following steps:

1. Enter the BIOS Setup Utility as detailed above.

2. Using the arrow keys, go to the Advanced menu.

3. Scroll down to Miscellaneous Configurations.

4. Scroll down to “UMA Video Memory Size”, and press the [Enter] key to see the submenu.

5. Press the [Enter] key to see a drop-down list of selections, or press the spacebar to cycle through the selections.

6. When you have selected the amount of memory you wish to use, press the F10 key and select [Yes] when asked if you want to save the configuration and exit.

BIOS Guide

A guide to your LifeBook notebook’s BIOS is available online. Please visit our service and support web site at http://us.fujitsu.com/computers. Once there, click on the Support link, then select Notebooks under User’s Guides in the side bar. Select LifeBook BIOS Guides

from the pull-down menu for your LifeBook model.

If your data security settings require it, you may be asked for a password before the BIOS main menu will appear.

BOOTING THE SYSTEM

We strongly recommend that you not attach any external devices or put a DVD/CD in your drive until you have gone through the initial power-on sequence.

When you turn on your LifeBook notebook for the first time, it will display a Fujitsu logo on the screen. If you do nothing the system will load the operating system, and then the Windows Welcome will begin.

Designed to accommodate the needs of many users, in many different countries, Windows needs to be configured the first time you use them. Windows has two parts:

■

Getting Started: You have the opportunity to review the Windows License Agreement, to enter custom information for your system, and to set up your modem so that your LifeBook notebook will be prepared to dial out.

■

Registration: Easy online registration for Windows with Microsoft.

You may click Cancel at any time within this process to shut down Windows. You may restart this process at any time in the future, but you must complete it in order to use your computer.

Getting Started

Read the instructions on the screens carefully and fill in the information as directed. You will be asked to read the Windows End User License Agreement. When you finish reading you must accept or reject the terms of the

agreement.

If you reject the terms of the License Agreement you will be returned to the beginning of the Windows Welcome Process, even if you shut your notebook down and start it up again.

You will then be asked for such items as the language you wish to use, the country in which you live, your first and last name, and about how you dial out from where you will be using your LifeBook notebook. For the modem settings, enter your current location information where you will be using your LifeBook notebook. If you are not connected to a phone line and plan to register at a later time, you may click the Skip button.

Once you have set up your LifeBook notebook to dial out, Windows will make a free telephone call to test the settings. If the call is unsuccessful, you will be returned to the phone settings page where you may try to fix them. If you are unable to fix the settings please contact Fujitsu Service and Support. (See Fujitsu Contact Infor- mation on page 3 for more information) If you would simply like to move on, and register at a later time, you may click the Skip button.

Windows Registration

If your connection is successful, you will receive an acknowledgement from Microsoft that your registration was successful.

WINDOWS PRODUCT ACTIVATION (WINDOWS XP ONLY)

If your system has Windows XP as an operating system, it has already been pre-installed and pre-activated when you receive the system.

In the event you need to re-install Windows XP (e.g., after making significant configuration changes), it may be necessary to reactivate the operating system. To do so, use the following information.

■

After re-installing Windows XP, you have thirty days to activate it. Product activation ensures that you are the authorized owner of the Windows XP operating system.

■

Until you activate the product, you will be prompted whenever you turn on the system that activation is required. Follow the on-screen directions to activate your operating system. The product only needs to be activated once, unless significant hardware changes are made to your system.

■

Note that Product Activation and Registration are not the same thing. Registration is optional, whereas Product Activation is a required procedure.

REGISTERING YOUR LIFEBOOK NOTEBOOK

What are the benefits of registering?

You will receive an identification label for your LifeBook notebook, which, if your notebook is ever lost, may help in getting it returned to you. You will also receive technical support access and useful product mailings.

How do I register my LifeBook notebook?

To register your LifeBook notebook, visit our Web site at: http://us.fujitsu.com/computers.

Starting Your LifeBook Notebook

INSTALLING CLICK ME!

The first time you boot up your system, you will see an icon called Click Me! on the desktop (Windows 2000) or in the Start folder (Windows XP). When you click the Click Me! icon, your system will automatically build the icon tray in the bottom right of the screen. These icons provide links to utilities that you will frequently access.

LifeBook C Series Notebook – Section Three

Power Management

Your LifeBook notebook has many features for conserving battery power. Some of these features are automatic and need no user intervention, such as those for the internal modem. However, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness. Internal power management for your LifeBook notebook may be controlled from settings made in your operating system, pre-bundled power management application, or from settings made in the BIOS setup utility.

Besides the options available for conserving battery power, there are also some things that you can do to prevent your battery from running down as quickly. For example, you can create an appropriate power saving profile, put your LifeBook notebook into Suspend mode when it is not performing an operation, and you can limit the use of high power devices. As with all mobile battery-powered computers, there is a trade-off between performance and power savings.

■

Selecting Standby from the Windows Shut Down menu.

■

Timing out from lack of activity (if the power profile has been set up accordingly).

■

Allowing the battery to reach the Dead Battery Warning condition.

Your LifeBook notebook’s system memory typically stores the files on which you are working, opens applications information, and any other data required to support the operations in progress. When you resume operation from Suspend mode, your LifeBook notebook will return to the point where it left off. You must use the Power/Suspend/Resume button to resume operation, and there must be an adequate power source available, or

your LifeBook notebook will not resume.

If you are running your LifeBook notebook on battery power, be aware that the battery continues to discharge while your LifeBook notebook is in Suspend mode, though not as fast as when fully operational.

POWER/SUSPEND/RESUME BUTTON

When your LifeBook notebook is active, the Power/ Suspend/Resume button can be used to manually put your LifeBook notebook into Suspend mode. Push the Power/Suspend/Resume button when your LifeBook notebook is active, but not actively accessing anything, and immediately release the button. You will hear two short beeps and your system will enter Suspend mode.

If your LifeBook notebook is suspended, pushing the Power/Suspend/Resume button will return your LifeBook notebook to active operation. You can tell whether or not your system is in Suspend mode by looking at the Power icon on the Status LCD Panel. (See Status Indi- cator Panel on page 13 for more information). If the indicator is visible and not flashing, your LifeBook notebook is fully operational. If the indicator is both visible and flashing, your LifeBook notebook is in Suspend mode. If the indicator is not visible at all, the power is off or your LifeBook notebook is in Hibernation (Save-to-Disk) mode. (See Hibernation Feature)

SUSPEND MODE

Suspend mode saves the contents of your LifeBook notebook’s system memory during periods of inactivity by maintaining power to critical parts. This mode will turn off the CPU, the display, the hard drive, and all of the other internal components except those necessary to maintain system memory and allow for restarting. Your LifeBook notebook can be put in Suspend mode by:

■

Pressing the Power/Suspend/Resume button when your system is turned on.

HIBERNATION (SAVE-TO-DISK) FEATURE

The Hibernation (Save-to-Disk) feature saves the contents of your LifeBook notebook’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature.

Enable or Disable the Hibernation Feature

Hibernation is the default setting for Windows XP. To disable or enable the Hibernation feature, follow these steps:

1. From the Start menu, select Settings (Windows 2000 only), and then select Control Panel.

2. From the Control Panel, double-click the Power Options icon.

3. Select the Hibernate tab. Select or deselect the box to enable or disable this feature.

Using the Hibernation Feature

1. From the Start menu, select Settings (in Windows

2000), then select Control Panel.

2. From the Control Panel, select Power Options.

3. Select the Advanced tab. Select Hibernate from the pull down menu for Power buttons. (Note that Hibernate will only appear as an option if it has

been enabled in the Hibernate tab).

The Suspend or Hibernation (Save-toDisk) mode should not be used with certain PC Cards. Check your PC Card documentation for more information.

Power Management

■

If your LifeBook notebook is actively accessing information when you enter the Suspend or Hibernation (Save-toDisk) modes changes to open files are not lost. The files are left open and memory is kept active during Suspend mode or the memory is transferred to the internal hard drive during Hibernation (Save-to-Disk) mode.

■

When PC Cards or external devices are in use, Save-to-Disk mode cannot return to the exact state prior to suspension, because all of the peripheral devices will be re-initialized when the system restarts.

■

The main advantage of using the Hibernation (Save-to-Disk) function is that power is not required to maintain your data. This is particularly important if you will be leaving your LifeBook notebook in a suspended state for a prolonged period of time. The drawback of using Hibernation (Saveto-Disk) mode is that it lengthens the power down and power up sequences and resets peripheral devices.

DISPLAY TIMEOUT

The Video Timeout is one of the power management parameters. This feature saves power by turning off the display if there is no keyboard or pointer activity for the user selected timeout period. Any keyboard or pointer activity will cause the display to restart automatically. This feature is independent of the Power/Suspend/ Resume button and can be enabled and disabled in Windows and the BIOS setup utility. (See BIOS Setup

Utility on page 27 for more information)

HARD DISK TIMEOUT

The Hard Disk Timeout is another one of the power management parameters. This feature saves power by turning off the hard drive if there is no hard drive activity for the user selected timeout period. Any attempt to access the hard drive will cause it to restart automatically. This feature is independent of the Power/ Suspend/Resume button and can be enabled and disabled in Windows and BIOS setup utility. (See BIOS

Setup Utility on page 27 for more information)

WINDOWS POWER MANAGEMENT

The Power Options icon located in the Windows Control Panel allows you to configure some of the power management settings. For example, you can use the Power Management to set the timeout values for turning off the display and hard disks whether you are running the LifeBook notebook on battery power or one of the

adapters. (See Pre-Installed Software on page 97 for more information) The settings may also be changed in the BIOS. (See BIOS Setup Utility on page 27 for more infor-

mation)

RESTARTING THE SYSTEM

If your system is on and you need to restart it, be sure that you use the following procedure.

1. Click the Start button, and then click Shut Down.

2. Select the Restart option from within the Windows Shut Down dialog box.

3. Click OK to restart your LifeBook notebook. Your

notebook will shut down and then reboot.

Turning off your LifeBook notebook without exiting Windows or turning on your notebook within 10 seconds of the notebook being shut off may cause an error when you start the next time.

POWER OFF

Before turning off the power by choosing Shut Down from Windows, check that the Hard Drive, optical drive, PC Card and Floppy Disk Drive Access indicators are all Off. (See figure 2-8 on page 13) If you turn off the power while accessing a disk or PC Card there is a risk of data loss. To ensure that your LifeBook notebook shuts down

without error, use the Windows shut down procedure.

Never turn your LifeBook notebook off while an application is running. Be sure to close all files, exit all applications, and shut down your operating system prior to turning off the power. If files are open when you turn the power off, you will lose any changes that have not been saved, and may cause disk errors.

Using the correct procedure to shut down from Windows, allows your LifeBook notebook to complete its operations and turn off power in the proper sequence to avoid errors. The proper sequence is:

1. Click the Start button, and then click Shut Down.

2. Select the Shut Down option from within the Windows Shut Down dialog box.

3. Click OK to shut down your LifeBook notebook.

If you are going to store your LifeBook notebook for a month or more, see the Care and Maintenance section of this manual.

LifeBook C Series Notebook – Section Three

User-Installable Features

LifeBook C Series Notebook – Section Four

Lithium ion Battery

Your LifeBook notebook has a Lithium ion battery that provides power for operating your LifeBook notebook when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards.

The Lithium ion battery operating time may become shorter if it is used under the following conditions:

■

When used at temperatures that exceed a low of 5°C or a high of 35°C. Extreme temperatures not only reduce charging efficiency, but can also cause battery deterioration. The Battery Charging icon on the Status Indicator Panel will flash when you try to charge a battery that is outside its operating temperature range.

(See Battery Charging Indicator on page 14 for more information)

■

When using a high current device such as a modem, DVD, or hard drive, using the AC adapter will conserve your battery life.

■

Actual battery life will vary based on screen brightness, applications, features, power management settings, battery condition and other customer preferences. Media player drive or hard drive usage may also have a significant impact on battery life. The battery charging capacity is reduced as the battery ages. If your battery is running low quickly, you should replace it with a new one.

■

Do not leave a faulty battery in your LifeBook notebook. It may damage your AC adapter, optional Auto/Airline adapter, a second battery or your LifeBook notebook itself. It may also prevent operation of your LifeBook notebook by draining all available current into the bad battery.

■

Under federal, state, or local law it may be illegal to dispose of batteries by putting them in the trash. Please take care of our environment and dispose of batteries properly. Check with your local government authority for details regarding recycling or disposing of old batteries. If you cannot find this information elsewhere, contact your support representative at 1-800-8Fujitsu (1-800-838-5487).

RECHARGING THE BATTERIES

If you want to know the charge condition of the primary Lithium ion battery, check the Battery Level indicator located on the Status Indicator panel. The indicator changes as the battery level changes.

The Lithium ion battery is recharged internally using the AC adapter or Auto/Airline adapter. To recharge the battery make sure the battery that needs to be charged is installed in your LifeBook notebook and connect the AC or Auto/Airline adapter. The Lithium ion battery can also be charged using an external battery charger, avail-

able from Fujitsu.

Make sure that the Battery Charging indicator and the percentage charge is shown inside the Battery Level icon on the Status Indicator Panel.

There is no memory effect on the Lithium ion battery, therefore you do not need to discharge the battery completely before recharging. Charge times will be much longer if your LifeBook notebook is in use while the battery is charging. If you want to charge the battery more quickly, put your LifeBook notebook into Suspend mode, or turn it off while the adapter is charging the battery. (See Power Management on page 30 for more

information on Suspend mode and shutdown procedure

Using heavy current devices such as a modem or frequent media player accesses may prevent charging completely.

Low Battery State

When the battery is running low, a low battery notification message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your LifeBook notebook will go into Suspend mode. There is no guarantee that your data will be saved

once the notebook reaches this point.

■

Once the low battery notification message appears, you need to either plug in an AC power adapter or Auto/ Airline adapter, or save all your active data, power down your system, and install a charged battery as soon as possible.

■

When you are in Suspend mode there must always be at least one power source active. If you remove all power sources while your LifeBook notebook is in Suspend mode, any data that has not been saved to the hard drive will be lost.

)

LifeBook C Series Notebook – Section Four

Battery Latches

Dead Battery Suspend mode shows on the Status indicator just like the normal Suspend mode. Once your LifeBook notebook goes into Dead Battery Suspend mode you will be unable to resume operation until you provide a source of power either from an adapter or a charged battery. Once you have provided power, you will need to press the Power/Suspend/Resume button to resume operation. In the Dead Battery Suspend mode, your data will be lost if a power source is not provided promptly. If the Power indicator stops flashing and goes out, you have lost the data that was not stored. Once you provide power, you can continue to use your LifeBook notebook while an adapter is charging the battery.

Shorted Batteries

The Status Indicator panel uses a symbol inside the battery outline of the Battery Level indicator to display the operating level available in that battery. (See Figure 2-9 on page 13). If this display shows a Shorted Battery, it means that the battery is damaged and must be replaced so it does not damage any other parts of your LifeBook notebook.

REPLACING THE BATTERY

With the purchase of an additional battery, you can have a fully charged spare to swap with one that is not charged. (Figure 4-1)

1. Have a charged battery ready to install.

2. Shut down your LifeBook notebook and disconnect the AC adapter.

3. Press the battery release latches while lifting the battery.

4. Remove the battery from the bay.

5. Slide the new battery into the bay. The pins will automatically align with the connector.

6. Press the battery down until the battery release latches snap into place.

7. Plug in the AC adapter and turn the power on.

Figure 4-1. Replacing the Battery

If the Lithium ion battery connector is not fully seated, you may not be able to use your LifeBook notebook or charge your battery.

Internal Floppy Disk Drive

Write Protected

Write Enabled

Figure 4-2. Loading/Ejecting a 3.5” Floppy Disk

Internal Floppy Disk Drive

Your LifeBook notebook has an internal floppy disk drive which can read and write information on removable 1.44 MB and 720 KB floppy disks.

LOADING A DISK

To load a disk into your disk drive, follow these easy steps:

1. Position the disk so that its label is facing upwards and the shutter side is pointing towards the drive.

(Figure 4-2)

2. Push the disk into the drive until the Eject button

pops out and you hear a click.

When there is no disk in the drive, the Eject button is flush with your LifeBook notebook.

EJECTING A DISK

To eject a disk from the disk drive, follow these easy steps:

1. Check that the Floppy Disk Drive Access indicator is inactive.

2. Press the Eject button. This will push your disk partially out of the drive.

3. Remove the disk.

PREPARING A DISK FOR USE

Before you can use a new disk, it needs to be prepared so your LifeBook notebook knows where to store information. This preparation is called formatting or initializing a disk. You will need to format new disks, unless they are preformatted. (Please refer to your operating

system manual for step-by-step instructions on formatting a disk)

To prevent accidental erasure of the data stored on a disk, slide the “write protect” tab until a small hole is exposed. This sets the disk into a protected state where nothing can be added or removed. If you want to add or remove data on a protected disk, slide the “write protect” tab to close the small hole. (Figure 4-3)

Figure 4-3. Floppy Disk Write Protect

■

If you eject the disk while the Floppy Disk Drive Access indicator is active, there is a risk of damaging the data on the disk, the disk itself or even the disk drive.

■

Formatting a floppy disk that already contains data will erase all of the information on the disk.

LifeBook C Series Notebook – Section Four

Media Holder Tray

Optical Drive Eject Button

Figure 4-4. Optical Drive

Optical Drive

Your system may have a DVD-RW drive, a DVD/CDRW drive, a DVD drive, or a CD-ROM drive. Collectively, these are known as “optical drives”. A variety of media is available to use with your system, depending upon the system configuration you have selected.

DVD-R and DVD-RW discs hold up to 4.7 GB of data. A DVD-R disc can only be written to once; DVD-RW discs can be written to over and over. DVD-R and DVD-RW discs can be played on most standard DVD players.

CD-R and CD-RW discs hold up to 640 MB of data. A CD-R disc can only be written to once; CD-RW discs can be written to over and over.

Depending upon the configuration of your notebook, you may have one of the following optical drives:

■

DVD-RW

A DVD-RW drive allows you to play CD’s and DVD’s, record CD-R’s and CD-RW’s, and record DVD-R’s and DVD-RW’s.

■

DVD/CD-RW combo

A DVD/CD-RW combo drive allows you to access movie, software, data, or audio DVD/CDs, and to write data onto recordable CD-R and CD-RW discs.

■

DVD

A DVD player gives you access to movie, software, data, and audio DVD/CDs.

■

CD-ROM

A CD-ROM drive allows you to access software, data, or audio CDs.

Install your media player software before first using the optical drive. Refer to the applicable readme file on the Driver Applications CD-ROM.

MEDIA PLAYER SOFTWARE

DVD model only: With the DVD drive and media player software you can play DVD movies and music CDs on your LifeBook notebook. The media player includes controls which allow you to take full advantage of the

features of a DVD movie, as well as standard features such as fast forward, fast reverse, pause, etc.

DVD/CD-RW Combo model only:

With the combo drive, you can play DVD movies, read audio CDs, and write data onto recordable CD-R or CD-RW discs.

DVD-RW model only:

With this drive, you can play CD’s

and DVD’s, record CD-R’s and CD-RW’s, and record

DVD-R’s and DVD-RW’s.

■

Do not operate your optical drive unless

your LifeBook notebook is sitting on a flat surface. Using a drive when the system is not level may damage the drive or prevent proper operation.

■

Prolonged use of the optical drive, such

as watching a DVD movie, will substantially reduce your battery life if no other power source is attached.

■

You should periodically check the Fujitsu web site at http:// us.fujitsu.com/computers for current updated drivers.

■

All LifeBook DVD players are set to play DVD titles with region code number 1 which is specified for the North American market. The region number is a regional restriction code defined by the DVD Forum acting on Hollywood requirements. Different region codes are recorded on video DVD titles for publication in different areas of the world. If the regional code of the DVD player does not match the codes on the titles, then playback is impossible.

■

You can change the region code on the DVD player using the Properties menu of the DVD software. Note, however, that you can only change the region code up to four times. After the fourth change, the last code entered becomes permanent, and cannot be changed.

Optical Drive

LOADING MEDIA ON YOUR DRIVE

To load a disc into your optical drive:

1. Push and release the eject button on the front of the optical drive to open the holder tray. The tray will come out of the LifeBook notebook a short distance.

2. Gently pull the tray out until a media disc can easily

be placed in the tray.

There may be a protective sheet in the tray from when it was shipped; please make sure it is removed before operating the drive.

3. Place the media into the tray, label side up, with the hole in the center of the disc. Snap the disc onto the raised circle in the center of the tray.

4. Gently push the holder tray back in until you

hear a click. (Figure 4-5)

If you have disabled the Auto Insert Notification Function, you will have to start the drive from your desktop, since your LifeBook notebook will not automatically recognize that media has been loaded.

2. Gently pull the tray out until the disc can easily be removed from the tray.

3. Carefully remove the media disc from the holder tray.

4. Gently push the holder tray back in until you hear a click.

USING THE MEDIA PLAYER SOFTWARE

Depending upon its configuration, your system may not have the media player software pre-installed. If it is not installed, reference the documentation that accompanies the media application.

Starting a DVD Movie (DVD Models only)

1. Insert the DVD movie into your optical drive. If the CD AutoRun feature activates, skip Step 2.

2a. Windows 2000 only: From the Start menu, select

Programs, then select InterVideo WINDVD and click InterVideo WINDVD or double-click on the InterVideo WINDVD icon on the desktop. This will launch the DVD movie.

2b. Windows XP only: The first time you insert a movie

into the DVD/CD-RW tray, you will be prompted to select what you want the system to do when discs are inserted (e.g., start automatically or wait for a prompt). Until you make a selection, you will receive the same prompt whenever you insert a disc.

3. Click OK to close the About DVD Player Performance dialog box and the movie will begin.

(a)

(c)

Figure 4-5. Loading/Ejecting Media

(b)

(d)

REMOVING MEDIA

1. Push and release the eject button on the front of the optical drive. This will stop the drive and the holder tray will come out of the LifeBook notebook a short distance.

Opening the Media Player Control Panel

With most DVD-ROMs, you have the option of altering how the movie should play and what you wish to view. You can do this by using the media player control panel and the mouse.

1. Right-click on the movie screen to open a dropdown menu for options.

2. Select View, then Player for all the controls available. This will open the control panel into the bottom of the screen.

Using the Media Player Control Panel

The media player software allows you to watch the movie much like a VCR player. You have the option to pause, rewind, fast-forward and stop the movie at any point.

1. To Pause the movie, click the on-screen button.

2. To Rewind the movie, click the  button to rewind to a specific portion of the movie, or the  button to return to the opening screen.

LifeBook C Series Notebook – Section Four

3. To Fast-forward the movie, click the  button to forward to a specific portion of the movie, or the button to jump to the ending credits.

4. To Stop the movie, click the  button.

Exiting the Media Player

1. Click the U located in the upper right corner of the title bar. This will open a media player dialog box.

2. Click Yes to stop and exit the movie, or No to close the media player dialog box and return to the movie.

™

USING DOLBY

HEADPHONE

The Dolby Headphone utility lets you enjoy multichannel sound sources, such as DVD movies, with realistic virtual surround sound using conventional stereo headphones. The Dolby Headphone is a utility that is available in the InterVideo WinDVD application.

Dolby Headphone is a signal processing system that enables your stereo headphones to realistically emulate

the sound of a five-speaker playback system.

■

Media discs which do not have the Dolby Surround 5:1 symbol will not support Dolby Headphone.

■

After making changes to the Dolby Headphone feature and clicking OK, wait at least ten seconds before making another change in order to allow the system to stabilize.

To use the Dolby Headphone feature, perform the following steps:

1. Double click the InterVideo WinDVD icon on your desktop.

2. On the toolbar that appears, click the Properties button (the fourth button from the left, with the image of a wrench).

3. On the Properties window, select the Dolby Headphone tab.

4. To enable Dolby Headphone, check the Enable Dolby Headphone box. To change the type of surround sound, select one of the radio buttons listed under Room Filter Setting.

5. Click OK. The Dolby Headphone feature will now be enabled until you disable it by unchecking Enable Dolby Headphone.

single charged battery. If you are watching a DVD movie on battery power you may need to swap in an additional, charged battery or attach AC power during the movie to

view it in its entirety.

An additional fully-charged battery is recommended if you will be watching DVD movies on battery power. If you don’t have an additional battery, you may purchase one either online at http://us.fujitsu.com/computers or by calling 1-877-372-3473.

To Watch a Movie on Battery Power:

1. Have an additional full-charged battery or your AC adapter ready for use.

2. Start watching your DVD movie.

3. When the low battery warning occurs, immediately

stop the movie and exit the media player.

If you do not stop the optical drive quickly and the LifeBook notebook attempts to auto-suspend (critical battery low state) the notebook will shut down improperly. If this occurs, you will need to perform a hard reset and follow any instructions presented before the system will reboot.

4. Power down your LifeBook notebook and replace the discharged battery with an additional fullycharged battery. If you do not have an additional battery, you should attach AC power as soon as you see the low battery warning.

5. Resume your notebook operation by pressing the Suspend button again.This is not required if you attached AC power without entering suspend mode.

6. Restart your optical drive, locate and skip to the chapter of the movie you were last watching.

7. Continue watching your DVD movie.

Some shorter DVD movies may not require you to swap batteries or attach AC power to complete them; however, it is best to be prepared since actual battery life while operating the media player cannot be guaranteed.

USING OPTICAL DRIVE ON BATTERY POWER

Since optical drives consume a lot of power, your overall battery life will be significantly shorter when operating the drive continuously (such as watching a DVD movie) than during standard operation. Many movie run-times are longer than your LifeBook notebook can support on a

Memory Stick/SD Card

Memory Stick

Memory Stick/ SD Card Slot

Note: A Memory Stick is used for illustration purposes.

Figure 4-6. Installing a Memory Stick/SD Card

Memory Stick/ Secure Digital Slot

Your LifeBook notebook supports Memory Stick/ Memory Stick Pro and Secure Digital (SD) Cards, on which you can store and transfer data to and from a variety of digital devices. These cards use flash memory architecture, which means they don’t need a power source to retain data.

Memory Stick is a flash memory technology developed by Sony Electronics. Memory Stick allows you to record, transfer and share digital content, such as digital pictures, movies, music, voice, and computer data and applications.

Secure Digital (SD) Cards are very similar to Memory Sticks, but they are shorter. Like the Memory Stick, SD Cards allow portable storage among a variety of devices, such as cell phones, GPS systems, digital cameras, and PDAs. SD Cards transfer data quickly, with low battery consumption. Like the memory stick, it uses flash memory architecture.

INSTALLING MEMORY STICK/SD CARDS

Memory Sticks and SD Cards are installed in the Memory Stick/SD Card slot (Figure 4-6). To install a

Memory Stick or SD Card, follow these steps:

■

Installing or removing a Memory Stick or SD Card during your LifeBook notebook’s shutdown or bootup process may damage the card and/or your LifeBook notebook.

■

Do not insert a card into a slot if there is water or any other substance on the card as you may permanently damage the card, your LifeBook notebook, or both.

1. See your Memory Stick or SD Card manual for

instructions on the installation of your card. Some cards may require that your notebook is off while installing them.

2. Make sure there is no card currently in the slot. If there is, see Removing a Memory Stick/SD Card.

3. Insert your PC Card into the slot with the product label facing up.

4. Push the card firmly into the slot until it is seated in the connector.

Figure 4-7. Memory Stick and Secure Digital Card

REMOVING A MEMORY STICK/SD CARD

To remove a Memory Stick or SD Card, follow these easy steps:

1. See your Memory Stick or SD Card manual for instructions on the removal of your card. Some cards may require your LifeBook notebook to be in Suspend Mode or Off while removing them.

LifeBook C Series Notebook – Section Four

LifeBook Digital Audio Out Port

To MiniDisc Recorder Port or home stereo

Optical Digital Audio Out

Your LifeBook notebook has an Optical Digital Audio Out Port to which you can connect an optional MiniDisc recorder to record music or to a home sound system to play your MP3 files. The optical digital audio out port is located on the right-hand side of your Life-

Book notebook.

MiniDisc recorder operation is dependent upon the individual vendor’s instructions. Be sure to thoroughly review any documentation that comes with your player before using your device.

CONNECTING AN OPTICAL DIGITAL CABLE

To connect a minidisc recorder or to a personal sound system, install the cable that came with your recorder as illustrated. Install the connector with the long plug into the player, as instructed in the vendor’s user instructions. Connect the other end of the optical digital cable to the Optical Digital Audio Out port on your LifeBook notebook. The Optical Digital Audio Out port is the middle round port on the right-hand side of your Life-

Book notebook.

Certain minidisc recorder cable connectors are configured differently from that illustrated. If your cable connector does not fit properly, you will need to purchase an adapter from a third-party electronics store.

Figure 4-8. Connecting Optical Digital Cable

Figure 4-9. Installing/Removing PC Cards

PC Card Slot

PC Card

Eject Button

PC Cards

Your LifeBook notebook supports Type I, Type II and Type III PC Cards, which can perform a variety of functions depending on which type of card you install. You can install one or two PC Cards at a time, depending on its type. Type I/II PC Cards can be installed together, while Type III PC Cards must be installed alone.

Some available PC Cards:

■

Fax/data modem cards (Type II)

■

Local area network (LAN) cards (Type II)

■

IDE solid-state disk cards (Type II)

■

SCSI cards (Type II)

■

Wireless LAN (802.11b) cards (Type II)

■

Hard Drive (ATA) cards (Type III)

■

Other PC Cards that conform to PCMCIA 2.1 or CardBus standards

For further information, refer to the instructions supplied with your PC Card.

INSTALLING PC CARDS

PC Cards are installed in the PC Card slot. To install a

PC Card(s), follow these steps:

■

Installing or removing a PC Card(s) during your LifeBook notebook’s shutdown or bootup process may damage the card and/or your LifeBook notebook.

■

Do not insert a PC Card into a slot if there is water or any other substance on the card as you may permanently damage the card, your LifeBook notebook, or both.

You may be required to log on as an Administrator or a member of the Administrator’s Group to complete this procedure. If your computer is connected to a network, network policy settings may also prevent you from completing this procedure.

1. See your PC Card manual for instructions on the installation of your card. Some cards may require that your notebook is off while installing them.

2. Make sure there is no PC Card currently in the slot. If there is, see Removing PC Cards.

3. If either of the eject buttons is extended, press it in until it clicks.

4. Insert your PC Card into the slot with the product label facing up.

5. Push the card firmly into the slot until it is seated in the connector.

REMOVING PC CARDS

To remove a PC Card(s), follow these steps:

1. See your PC Card manual for specific instructions on removing your card. Some PC Cards may require your LifeBook notebook to be in Suspend Mode or

Off while removing them.

■

Windows has a shutdown procedure for PC Cards that must be followed before removing a card. (Review your operating system manual for the correct procedure.) It is good practice to remove devices using the Unplug or Eject Hardware icon in the system tray.

■

If the dialog box states that the device cannot be removed, you must save all of your open files, close any open applications and shut down your notebook.

2. Unlock the card from the slot by pressing the eject button associated with the slot in which the card is located. When pressed, the button will pop out.

3. Firmly press the button again until it is flush with the notebook. This will eject the card slightly out of

the slot allowing you to remove the card.

If the PC Card(s) has an external connector and cable, do not pull the cable when removing the card.

LifeBook C Series Notebook – Section Four

Memory Upgrade Module

Your LifeBook notebook comes with 256 MB of on-board high speed Synchronous Dynamic RAM (SDRAM, PC2100-type, DDR, 266 MHz) factory installed. To increase your LifeBook notebook’s memory capacity, you may install an additional memory upgrade module. The memory upgrade must be a dual-in-line (DIMM) SDRAM module. To ensure 100% compatibility, purchase the SDRAM module only from the Fujitsu web store at: http://us.fujitsu.com/computers.

INSTALLING A MEMORY UPGRADE MODULE

To install a memory upgrade module follow these steps:

■

Turn off power and remove any telephone line connections before performing the memory upgrade.

■

If the computer has been used recently, it may be hot. Make sure the system has cooled off completely before changing memory.

1. Turn off power to your LifeBook notebook and remove any power adapter (AC or auto/airline) and telephone line connections.

2. Place your LifeBook notebook on a clean work surface.

3. Open the top cover all the way, so that it is lying flat on the work surface.

4. Slide the access cover slightly to the left until it becomes disengaged. Remove it from the system (Figure 4-10)

5. Push the keyboard toward the back of the system until it disengages and can be lifted freely. (Figure 4-11)

Figure 4-11. Sliding the keyboard

7. Carefully pivot the front of the keyboard away from the laptop until it is lying on the display. (Figure 4-12)

Figure 4-12. Folding the keyboard back

8. Align the connector edge of the memory upgrade module, chip side up, with the connector slot in the compartment. (Figure 4-13)

9. Insert the memory upgrade module at a 45

angle

and press it firmly onto the connector.

10. Press the memory upgrade module down into the compartment until it locks underneath the retaining clip. You will hear a click when it is properly in place.

(Figure 4-13)

Figure 4-10. Sliding the access cover

The memory upgrade module can be severely damaged by electrostatic discharge (ESD). Be sure you are properly grounded when handling and installing the module, and follow ESD precautions noted in the literature that accompanies the memory module.

11. Carefully flip the keyboard back into its original

Figure 4-13. Inserting a new memory module

position, and slide it towards the front of the unit until it is seated. (Figure 4-14)

Figure 4-14. Reinstalling the keyboard

12. Replace the access cover you removed in step 4. (Figure 4-15) Installation of the new memory module is now complete.

Memory Upgrade Module

4. Store the memory upgrade module in a static guarded sleeve.

5. Replace the keyboard by following steps 11 and 12 of

Installing a Memory Upgrade Modul

After changing your memory module configuration, you must complete the Resetting the Hibernation (Save-to-Disk) Parameters procedure in order for the Hibernation (Save-to-Disk) mode to operate properly on your LifeBook notebook.

(See Hibernation (Save-to-Disk) Feature on page 30 for more information)

CHECKING THE COMPUTER RECOGNITION OF NEW MEMORY CAPACITY

Once you have changed the system memory capacity by either adding or removing a memory upgrade module, be sure to check that your LifeBook notebook has recognized the change.

You can check the memory capacity by looking at the Info menu of the BIOS setup:

Figure 4-15. Replacing the access cover

The memory upgrade module is not something you routinely remove from your LifeBook notebook. Once it is installed, you should leave it in place unless you want to increase system memory capacity.

REMOVING A MEMORY UPGRADE MODULE

1. Perform steps 1 through 7 of Installing a Memory Upgrade Module.

2. Pull the clips sideways away from each side of the memory upgrade module at the same time.

(Figure 4-16)

Figure 4-16. Removing a memory module

3. While holding the clips out, remove the module from the slot by lifting it up and pulling towards the back of your LifeBook notebook.

1. Turn on the power to your LifeBook notebook using the Power/Suspend/Resume button.

2. Allow the system to start booting and press the F2 key once the Fujitsu logo appears on the screen with a prompt below it. This will open the main menu of the BIOS setup with the current settings displayed.

(See BIOS Setup Utility on page 27 for more information). Use the right arrow key to select Info in the

BIOS Setup menu.

The System Memory and the Extended Memory capacity, as detected by your LifeBook notebook during the Power On Self Test (POST), are displayed at the bottom of the Info menu screen. The chart below shows

the possible displays that can be shown on the screen.

If the total memory displayed is incorrect, check that your memory upgrade module is properly installed. (If the module is properly installed and the capacity is still not correctly recognized, see the Troubleshooting section starting on page 73)

Memory Displayed

Onboard

256 MB 256 MB 256 MB 256 MB

Memory Slot

0 128 MB 256 MB 512 MB

Total Memory

256 MB 384 MB 512 MB 768 MB

LifeBook C Series Notebook – Section Four

Device Ports

Your LifeBook notebook comes equipped with multiple ports to which you can connect external devices including: disk drives, keyboards, modems, printers, etc.

MODEM (RJ-11) TELEPHONE JACK

The modem (RJ-11) telephone jack is used for an internal modem. To connect the telephone cable follow these easy steps: (See Figure 2-6 on page 11 for location)

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

3. Plug the other end of the telephone cable into a telephone outlet

INTERNAL LAN (RJ-45) JACK

The RJ-45 jack is used to connect the internal Fast Ethernet (10/100 Base-T/Tx) to a Local Area Network (LAN) in your office or home, or broadband devices such as a cable modem, DSL, or satellite internet. If your notebook has been configured with internal LAN capability you will need to configure your notebook to work with your particular network. (To properly set up your LAN environment, consult a networking professional. Refer to your network administrator for information on your network configuration.) To connect the LAN cable follow these easy steps: (See Figure 2-6 on page 11 for location)

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

3. Plug the other end of the cable into a LAN outlet.

The internal modem is not intended for use with Digital PBX systems. Do not connect the internal modem to a Digital PBX as it may cause serious damage to the modem or your entire LifeBook notebook. Consult your PBX manufacturer’s documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem.

■

The internal modem on all LifeBook notebooks are certified for use in the United States and Canada. The modem may be certified in other countries.

(also known as “FireWire”). The IEEE 1394 standard is easy to use, connect, and disconnect. This port allows up to 400 Mbps transfer rate. A third-party application is required to operate your device with the 1394 port

The 1394 port used in this system uses a four-pin configuration. If you intend to interface with devices which use a six-pin configuration, you will need to purchase an adapter.

In order to connect a 1394 device, follow these steps:

(See Figure 2-4 on page 9 for location)

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

UNIVERSAL SERIAL BUS PORT

A Universal Serial Bus (USB) 2.0 port allows you to connect USB devices such as game pads, pointing devices, keyboards and speakers. USB 2.0 is downwardcompatible with USB 1.1 devices, so older USB devices will work with these ports. USB 2.0 is a much faster design, running forty times faster than USB 1.1. To connect a USB device follow these steps: (See Figure 2-6

on page 11 for location)

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

Due to ongoing changes in USB technology and standards, not all USB devices or drivers are guaranteed to work.

PARALLEL PORT

The parallel port, or LPT port, allows you to connect parallel devices, such as a printer to your notebook. In order to connect a parallel interface device, follow these steps: (See Figure 2-6 on page 11 for location)

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

3. Tighten the two hold-down screws, located on each end of the connector.

MICROPHONE JACK

The microphone jack allows you to connect an external mono microphone. Your microphone must be equipped with a 1/8"(3.5 mm) mono mini-plug in order to fit into the microphone jack of your LifeBook notebook. In order to connect a microphone follow these easy steps:

(See Figure 2-5 on page 10 for location)

IEEE 1394 PORT

The 4-pin 1394 port allows you to connect digital devices that are compliant with IEEE 1394 standard

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

Device Ports

OPTICAL DIGITAL AUDIO-OUT CONNECTOR

The optical digital audio-out connector allows you to download digital audio to MiniDisc recorders or connect to your sound system to play audio files. It uses SPDIF (Sony Philips Digital Interface) format. Please use the following setting when using the digital audio-out connector. (See Figure 2-5 on page 10 for location)

1. Click on Start, Settings and then click on Control Panel.

2. Select Yamaha Ds-XG Audio Configuration.

3. Click on the SPDIF tab and click on Digital Sources Only. If you don’t see this setting, the optical digital

is always on by default.

■

There are several types of cables for connecting a digital electronic device (e.g., MD player) to the audio-out connector, depending on the connector type. The connector on your computer is a Optical Mini Plug (3.5mm diameter mini plug)

■

The frequency of the digital sound output from the SPDIF output connector is fixed to 48 KHz. If a sampling rate convertor is not installed in your digital electronic device (e.g., MD player), recording is not possible. See the device user manual for more details.

■

Sound recorded by connecting a digital electronic device to the SPDIF output connector cannot be used as digital output. All output data from the SPDIF output connector has copyright protection information included.

than NTSC or PAL. To connect an S-Video device, follow these steps: (See Figure 2-4 on page 9 for location)

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

EXTERNAL MONITOR PORT

The external monitor port allows you to connect an external monitor. To connect an external monitor follow these steps: (See Figure 2-6 on page 11 for location)

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

3. Tighten the two hold-down screws, located on each end of the connector.

Pressing the [Fn] + [F10] keys allows you to change the destination of your display video. Each time you press the key combination, you will step to the next choice, starting with the built-in display panel only, moving to the external monitor only, finally moving to both the built-in display panel and an external monitor.

SERIAL PORT

The serial port allows you to connect serial devices, such as printers or scanners. In order to connect a serial interface device follow these easy steps:

1. Align the connector with the port opening. (See

Figure 2-6 on page 11 for location)

2. Push the connector into the port until it is seated.

3. Tighten the two hold-down screws, located on each end of the connector.

HEADPHONE JACK

The headphone jack allows you to connect headphones or powered external speakers to your LifeBook notebook. Your headphones or speakers must be equipped with a 1/8" (3.5 mm) stereo mini-plug. In order to connect headphones or speakers follow these steps: (See

Figure 2-5 on page 10 for location)

1. Align the connector with the port opening.

2. Push the connector into the port until it is seated.

If you plug headphones into the headphone jack, you will disable the builtin stereo speakers.

S-VIDEO OUT PORT

The S-Video port allows you to connect and use directly any S-Video device, such as a VCR or television. The S-Video standard provides for a higher quality picture

INFRARED PORT

The Infrared IrDA (4 Mbps) port allows for wireless data transfer between your notebook and other IrDAcompatible devices, such as another computer or a printer, without the use of a cable. (See Figure 2-5 on

page 10 for location)

It is important to keep in mind that while carrying out this form of communication, both devices must be placed so their infrared ports are directly facing each other without obstruction. The devices must also be separated by at least 6" but no more than 36" for maximum performance.

■

Do not move either device while communication is active as it may interrupt data transmission.

■

Be careful not to scratch the infrared port lens. Dirt, scratches, or other surface marks can degrade operation.

LifeBook C Series Notebook – Section Four

Using the Integrated Wireless LAN*

*Optional device

LifeBook C Series Notebook – Section Five

WIreless LAN User’s Guide

FCC REGULATORY INFORMATION

Please note the following regulatory information related to the optional wireless LAN device.

Regulatory Notes and Statements

Wireless LAN, Health and Authorization for use

Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones. Wireless LAN devices are safe for use by consumers because they operate within the guidelines found in radio frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments, such as:

• On board an airplane, or

• In an explosive environment, or

• In situations where the interference risk to other devices or services is perceived or identified as harmful.

In cases in which the policy regarding use of Wireless LAN devices in specific environments is not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain authorization to use these devices prior to operating the equipment.

Regulatory Information/Disclaimers

Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution or attachment of connecting cables and equipment other than those specified by the manufacturer. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. The manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failure to comply with these guidelines.

Federal Communications Commission statement

This device complies with Part 15 of FCC Rules.

Operation is subject to the following two conditions: (1) This device may not cause interference, and, (2) This device must accept any interference, including interference that may cause undesired operation of this device.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the distance between the equipment and the receiver.

3. Connect the equipment to an outlet on a circuit different from the one the receiver is connected to.

4. Consult the dealer or an experienced radio/TV technician for help.

FCC Radio Frequency Exposure statement

This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65C and found compliant with the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices. The radiated output power of this Wireless LAN device is far below the FCC radio frequency exposure limits. Nevertheless, this device shall be used in such a manner that the potential for human contact during normal operation is minimized. When using this device, a certain separation distance between antenna and nearby persons must be maintained to ensure RF exposure compliance. In order to comply with RF exposure limits established in the ANSI C95.1 standards, the distance between the antennas and the user should not be less than 20 cm (8 inches).

Export restrictions

This product or software contains encryption code which may not be exported or transferred from the US or Canada without an approved US Department of Commerce export license. This device complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Modifications not expressly authorized by Fujitsu Computer Systems Corporation may invalidate the user's right to operate this equipment.

Canadian Notice

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.

LifeBook C Series Notebook - Section Five

Figure 5-1. Ad Hoc Mode Network

Before Using the Wireless LAN

The Integrated Wireless LAN is an optional device available for Fujitsu mobile computers. This manual describes the basic operating procedures for the Wireless LAN (referred to as the “device” in this manual) and how to set up a wireless LAN network. Before using this device, read this manual carefully to ensure correct operation of the device. Keep this manual in a safe place for reference while using the device.

Wireless LANs Covered by this Document

This document is applicable to systems containing an Atheros Wireless LAN.

Characteristics of the Device

This device consists of a wireless LAN card that is attached inside the computer via a mini-PCI slot.

The main characteristics are as follows:

■

It operates in the 2.4 GHz Industrial, Scientific, and Medical (ISM) RF band.

■

It does not require the procurement of an FCC license to operate.

■

It uses Direct Sequence Spread Spectrum (DS-SS), an RF modulation scheme that is resistant to noise.

■

This device complies with Wi-Fi, and is able to communicate at the maximum transfer rate of 11 Mbps.

■

The maximum communication range is approximately 80 feet (25 meters) inside a building. The range may be shorter depending upon the installation factors, such as walls and columns.

■

Unauthorized access can be prevented with the use of an SSID and an encryption key (also known as a WEP key).

Wireless LAN Modes Using this Device

Ad Hoc Mode (See Figure 1)

“Ad Hoc Mode” refers to a type of wireless network that involves connecting multiple computers without the use of an Access Point. Network connectivity between computers can be established using only wireless LAN cards in a peer-to-peer fashion.

Ad Hoc networks are an easy and inexpensive method for establishing network connectivity between multiple computers.

In the Ad Hoc mode, you can use the function supported by Microsoft Network, such as File and Print Sharing to exchange files and share a printer or other peripheral devices.

To use the Ad Hoc Mode, you must set the same SSID and the same encryption key for all the computers that are connected. All connected computers can communicate with each other within the communication range.

Access Point (Infrastructure) Mode (See Figure 2)

If a number of computers are connected simultaneously in the Ad Hoc mode, the transfer rate may be reduced, communications may become unstable, or the network connection could fail. This is because all wireless LAN cards are using the same radio frequency in the network.

To improve this situation, you can use a wireless LAN access point, which is sold separately. The wireless LAN network is in the “Access Point mode” when it uses an access point, and such a connection is called the “Access Point Network” or “Infrastructure Network”.

By using an access point, you can set and use a different communication channel for each network group. Each channel is given a different radio frequency, and it

WIreless LAN User’s Guide

Figure 5-2. Access Point (Infrastructure) Mode Network

Internet

ADSL modem, cable modem, or similar

Wired LAN

Wireless LAN

Access Point*

* An optional hub for a wired LAN may be required depending upon the type of access point used.

eliminates the collision of communications and provides a more stable communications environment.

How to Handle This Device

The Integrated Wireless LAN device is already installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The LAN has been configured to support the operating system with which your system shipped.

FOR BETTER COMMUNICATIONS

This personal computer may not operate properly due to the operating environment. Strictly observe the following precautions when installing the main unit of the computer:

■

Since this personal computer and equipment compliant with IEEE802.11a differ in operation frequency, it is not possible to communicate between both.

■

The recommended wireless communications distance is within a line-of-sight radius of 25 meters. For reasons related to the characteristics of the wireless LAN, however, the actual communications distance depends on the structure of the building in which the wireless LAN function is to be used, the presence/absence of obstructions, the types of software to be used, installation status, radio-wave status, or other operating conditions. Decreases in communications speed or a communications failure may also occur.

■

Distance the main unit of this personal computer is from other electric appliances. If the main unit of the person computer is installed near a powered-on electric appliance, the computer may not be able to communicate properly or trouble may occur in the electric appliance.

■

If the computer is unable to communicate properly, change the channel to be used or the installation location. During the use of a microwave oven or other equipment generating strong high-frequency energy, in particular, the personal computer may be highly susceptible to the energy and unable to communicate properly.

■

If a broadcasting station or wireless communications equipment is present nearby and this prevents the computer from communicating properly, moving the main unit of the computer is suggested. Radio interference may also occur if the intensity of ambient radio waves is too high.

STOPPING TRANSMISSION

To use this product inside hospitals, clinics, or airplanes, or in other places where the use of electronic equipment is regulated, stop the transmission of radio waves from the wireless LAN beforehand.

Deactivation using the wireless switch

The transmission of radio waves from the wireless LAN can be stopped by setting the wireless switch to the Off

LifeBook C Series Notebook - Section Five

Wireless LAN On/Off Switch

position. Note that the Wireless LAN On/Off switch has no effect on non-Wireless LAN models.

(See Figure 3 for Wireless LAN switch location.)

Figure 5-3. Wireless LAN On/Off Switch

Deactivation using Windows

1. Click [Start] --> [Settings (Windows 2000 only)]

-> [Control Panel] --> [Atheros Wireless Utility]. The Atheros Wireless Configuration Utility window will be displayed.

2. Click the Wireless Networks tab.

3. Click the [Enable Radio] box to clear it, then click the [OK] button. Wireless communications on/off switching will be deactivated and the transmission of radio waves from the wireless LAN will be stopped.

To restart transmission, check the [Enable Radio] checkbox to select it., then click the [OK] button.

STARTING TRANSMISSION

To communicate using the wireless LAN function, set the computer to a status from which it can transmit, as follows:

1. Click the Wireless Network Connection icon in the

system tray at the lower right of your screen.

2. Click [Enable Radio]. The radio will be turned on.

Access Point Mode: Transmission is enabled. Ad Hoc Mode: Restart your computer to enable the

radio.

Connection using Windows XP

WIreless LAN User’s Guide

FLOW OF OPERATIONS

The wireless LAN connection procedure contained in this section is outlined below.

1. Make sure the mobile computer is ready for the

transmission of radio waves from the wireless LAN. For further details, see (See Starting Transmission on page 54 for more information).

2. Assign the parameters required for wireless LAN connection. (See Preparation for wireless LAN con- nection on page 55 for more information).

■

Enter the network name (SSID) and other data.

■

Enter the network key (the Wired Equivalent Privacy or WEP key used to encode 802.11b communications data).

3. Perform setting operations relating to network connection. (See Connection to the network on page 57

for more information)

■

Specify TCP/IP as the protocol, and confirm the name of the work group and other settings.

■

Enter the data required for file/printer sharing on the network. Perform this operation as required.

■

For access point (or “infrastructure”) connection, enter data for the access point. Refer to the manual of the access point for further details.

■

Verify that you are able to connect your computer to the network.

PREPARATION FOR WIRELESS LAN CONNECTION

This section explains the preparations required for the use of the wireless LAN.

Assigning parameters

Enter the network name (SSID), the network key, and other data required for wireless LAN connection. If there is the administrator of the network, contact the network administrator for data settings.

■

To use access point (infrastructure) connection, refer to the access point manual for the access point-setting procedure.

■

You do not need to set the channel when using access point (infrastructure) mode. Channel selection is controlled by the access point. In ad hoc networks, channel selection defaults to channel 11; however, channel selection can be manually changed if desired. This can be accomplished only when using the client utility.

If it is necessary to change the channel, change the setting of the access point. For the setting procedure, refer to the manual of the access point.

1. Make sure the Wireless LAN switch is switched on.

2. Click the [Start] button first and then [Control Panel].

3. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed instead.)

4. Double-click the Network Connections icon. A list of currently installed networks will be displayed.

5. Right-click [Wireless Network Connection] in the list, and then click [Properties] in the menu displayed. The [Wireless Network Connection Properties] window will be displayed.

6. Click the [Wireless Networks] tab.

7. Click [Refresh], then choose the correct SSID from the [Available Networks] window. Click [Configure] and proceed to step 7. If the SSID of your access point does not appear in the list, click [Add]. The [Wireless Network Properties] window will be displayed.

8. Select the Association tab if it is not already selected.

9. Enter the information required for connection to the wireless LAN.

a. Enter the network name (SSID). (i.e., Enter the

name of the desired network in less than 33 ASCII characters).

LifeBook C Series Notebook - Section Five

For ad hoc connection: Assign the same network name to all the personal computers to be connected.

For access point (infrastructure) connection:

Assign the appropriate SSID. The SSID must be identical to the SSID of the access point. Refer to the access point manual, or contact your network administrator.

b. For ad hoc connection, check the following field.

For access point (infrastructure) connection, clear the check mark for the following field:

[This is a computer-to-computer (ad hoc) network; wireless access points are not used.]

10. Enter the WEP key for encoding communications

data.

It is strongly recommended that you enter the network key for encoding communications data. If the network key is not entered, since the network can be accessed from all personal computers containing the wireless LAN function, there is the danger of your data being stolen or damaged by other users.

a. Check the [Data encryption (WEP enabled)]

check box

For ad hoc connection: Clear the check mark from the [Network Authentication (Shared mode)] check box.

For access point (infrastructure) connection: If the access point to be accessed has acquired shared-key authentication, check the [Network Authentication (Shared mode)] check box.

For open-system authentication, clear the check mark. For access point setting, refer to the manual of the access point.

this case are as follows: 0- 9, A - Z, a - f

For ad hoc connection: Assign the same network key to all the personal computers to be connected.

For access point (infrastructure) connection:

Assign the identical network key that is programmed into the access point. For this setting, refer to the access point manual or contact your network administrator.

d. Confirm the Network key by re-entering the

same data in the [Confirm network key:] field.

e. Make sure that [Key index (advanced)] is set to

“1”. (Any value from “1” to “4” can be assigned to [Key index (advanced)]. “1” is usually assigned, however).

11. Click the [Authentication] tab and then verify the settings of [Enable network access control using IEEE 802.11x].

For internal use at an organization such as a company, when access by wireless LAN clients is to be limited using IEEE 802.11x authentication, check the [Enable network access control using IEEE

802.11x] check box.

For home use, clear the check mark from [Enable network access control using IEEE 802.11x].

For the setting method relating to IEEE 802.11x authentication, refer to the manual of the access point which you are using.

12. After completion of setting operations, click the [OK] button. Processing will return to the [Wireless Network Connection Properties] window.

13. Verify that the network name entered in step 7 above is added in [Preferred Networks], and then

click the [OK] button.

b. Clear the check mark from the [The key is

provided for me automatically] check box.

c. Enter data in [Network Key]. Depending on the

number of entered characters or digits, whether the key is an ASCII character code or a hexadecimal code will be identified automatically.

■

Use five or thirteen characters to enter the key in the ASCII character code format. The characters that can be used as the “network key” are as follows: 0 - 9, A - Z, _ (underscore), or,

■

Use 10 or 26 characters to enter the key in the hexadecimal character code format. The characters that can be used as the “network key” in

In [Preferred Networks], register only the desired connection settings.

14. Close the [Wireless Network] window.

WIreless LAN User’s Guide

CONNECTION TO THE NETWORK

This section explains connection to the network.

If there is an administrator of the network, contact the network administrator for data settings.

Setting the network

Perform the “Setting TCP/IP” and “Confirming the computer and work group names” operations required for network connection.

Setting TCP/IP

To change the setting of the IP address, you need to be logged in from Windows as an administrator.

1. Click the [Start] button first and then [Control Panel].

2. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed.)

3. Double-click [Network Connections]. A list of currently installed networks will be displayed.

4. Right-click [Wireless Network Connection] in the list, and then click [Properties] in the menu displayed. The [Wireless Network Connection Properties] window will be displayed.

Following this operation, confirm the names of the

computer and the workgroup as follows.

Confirming the computer and work group names

To modify the computer name and/or the work group name, you need to be logged in from Windows as an administrator.

1. Click the [Start] button, then [Control Panel].

3. Double-click the [System] icon. The [System Properties] window will be displayed.

4. Click the [Computer Name] tab.

5. Confirm the settings of [Full computer name:] and [Workgroup:].

a. The setting of [Full computer name:] denotes the

name for identifying the computer. Any name can be assigned for each personal computer.

To change the name, click [Change] and then proceed in accordance with the instruction messages displayed on the screen.

5. Click the [General] tab if it is not already selected.

6. Click [Internet Protocol (TCP/IP] and then click [Properties]. The [Internet Protocol (TCP/IP) Properties] window will be displayed.

7. Set the IP address as follows:

■

For ad hoc connection: Select [Use the following IP address:] and then enter data for [IP address] and [Subnet mask]. See page 69 for IP address setting.

■

For access point (infrastructure) connection: If your network uses DHCP, select [Obtain an IP address automatically] and [Obtain DNS server address automatically]. If your network uses static IP addresses, consult with your network administrator for the correct IP address settings.

8. Click the [OK] button. Processing will return to the

[Wireless Network Connection Properties] window.

9. Click the [OK] button.

10. Close the [Network Connection] window.

Enter the desired name in less than 15 ASCII character code format. Identifiability can be enhanced by entering the model number, the user name, and other factors.

b. [Workgroup name] is the group name of the

network. Enter the desired name in less than 15 ASCII character code format.

For ad hoc connection: Assign the same network name to all personal computers existing on the network.

For access point (infrastructure) connection:

Assign the name of the work group to be accessed.

6. Click the [OK] button. If a message is displayed that requests you to restart the personal computer, click [Yes] to restart the computer.

Setting the sharing function

Set the sharing function to make file and/or printer sharing with other network-connected personal computers valid.

This operation is not required unless the sharing function is to be used.

LifeBook C Series Notebook - Section Five

The folder and printer for which the sharing function has been set will be usable from any personal computer present on the network.

To share a file and/or the connected printer, you need to be logged in as an administrator.

Setting the Microsoft network-sharing service

1. Click the [Start] button first and then [Control Panel].

3. Double-click [Network Connections]. A list of currently installed networks will be displayed.

4. Right-click [Wireless Network Connection] in the list, and then click [Properties] in the menu displayed. The [Wireless Network Connection Properties] window will be displayed.

5. If [File and Printer Sharing for Microsoft Net- works] is displayed, proceed to step 6. If [File and Printer Sharing for Microsoft Networks] is not displayed, skip to step 7.

6. Make sure that the [File and Printer Sharing for Microsoft Networks] check box is checked, and then click the [OK] button. Skip to “Setting filesharing function”.

7. Click [Install]. The [Select Network Component Type] window will be displayed.

8. Click [Service], then click the [Add] button. The [Select Network Service] window will be displayed.

9. Click [File and Printer Sharing for Microsoft Networks] and then click the [OK] button. Processing will return to the [Wireless Network Connection Properties] window, and [File and Printer Sharing for Microsoft Networks] will be added to the list.

10. Click the [Close] button.

Setting the file-sharing function

The procedure for setting the file-sharing function follows, with the “work” folder in drive C: as an example.

1. Click the [Start] button first and then [My Com-

puter].

3. Right-click the “work” folder (or whichever folder you want to share), and then click [Sharing and Security...] in the menu displayed. The [Folder

Name Properties] window will be displayed.

Setting the file-sharing function for the file which has been used to execute Network Setup Wizard is suggested on the screen. For the wireless LAN, however, since security is guaranteed by entry of the network name (SSID) and the network key, the steps to be taken to set the filesharing function easily without using Network Setup Wizard are given below.

4. Click [Sharing] if it isn’t already selected.

5. Click the link stating “If you understand the security risks, but want to share files without running the wizard, click here”.

6. Click “Just enable file sharing” and click [OK].

7. Check the [Share this folder on the network] check

box.

To specify the corresponding folder as a read-only folder, select the [Read only] checkbox under the General tab.

8. Click the [OK] button. The folder will be set as a sharable folder, and the display of the icon for the “work.” folder will change.

Setting the printer-sharing function

1. Click the [Start] button first and then [Printers and FAX]. A list of connected printers will be displayed.

2. Right-click the printer for which the sharing func-

tion is to be set, and then click [Sharing] in the menu displayed. The property window correspond-

ing to the selected printer will be displayed.

Setting the printer-sharing function when Network Setup Wizard has been executed is suggested on the screen. For the wireless LAN, however, since security is guaranteed by entry of the network name (SSID) and the network key, the steps to be taken to set the printer-sharing function without using Network Setup Wizard are laid down below.

2. Double-click [Local disk (C:)].

WIreless LAN User’s Guide

3. Click the [Sharing] tab.

4. Click [Share this printer].

5. Enter the sharing printer name in [Share name].

6. Click the [OK] button.

Confirming connection

After you have finished the network setup operations, access the folder whose sharing has been set for other personal computers. Also, confirm the status of the radio waves in case of trouble such as a network connection failure.

In the case of access point (infrastructure) connection, enter the necessary data for the access point before confirming connection. Refer to the manual of the access point for the access point setup procedure.

Connecting your personal computer to another personal computer

1. Click [Start] first and then [My Computer]. The [My Computer] window will be displayed in the left frame.

2. Click [My Network Places] in the “Other Places” list. The window [My Network Places] will be displayed.

3. Click [View workgroup computers] under Network Tasks in the left frame.

4. Double-click the personal computer to which your personal computer is to be connected. The folder that was specified in “Setting the file-sharing function” on page 58 will be displayed.

5. Double-click the folder to be accessed.

Confirming the status of the radio

1. Right-click the Atheros icon in the lower right cor-

ner of the screen.

2. Click [Open Client Utility]. The Atheros Wireless Configuration Utility window opens.

3. Contained within the Current Status tab and Advanced Current Status, you will find the current operating status of the radio. (When the radio is turned off or the computer is not yet connected, some of the conditions will not be displayed.)

■

Profile Name

The current configuration profile is displayed.

■

Network Type - Configured Network Type

[Access Point] or [AdHoc] will be displayed.

■

Current Mode

Indicates the frequency and data rate currently used by the radio.

■

Current Channel

The channel number currently used by the radio.

■

Link Status

Displays the current connected state of the WLAN module.

■

Encryption Type

Displays the encryption type currently used by the radio.

■

IP Address

Displays the current TCP/IP address assigned to the WLAN adapter.

■

Country

The country with the country code for which the radio is configured.

■

Transmit Po wer Level

Displays the current transmit power level of the radio.

■

Network Name (SSID)

Displays the Network Name (SSID) currently used by the radio.

■

Power Save Mode

Displays the configured Power Save Mode currently used by the radio. [Off], [Normal], or [Maximum] will be displayed.

■

BSSID

Displays the Basic Service Set Identifier. This is typically the MAC address of the Access Point or in the case of AdHoc networks, is a randomly generated MAC address.

■

Frequency

Displays the center frequency currently being used by the radio.

■

Transmit Rate

Displays the current data rate used by the radio to transmit data.

■

Receive Rate

Displays the current data rate used by the radio to receive data.

LifeBook C Series Notebook - Section Five

Connection using Windows 2000

FLOW OF OPERATIONS

The wireless LAN connection procedure is outlined below.

1. Make sure that the personal computer is ready for the transmission of radio waves from the wireless LAN. For further details, see “Starting the transmission” on page 54.

2. Assign the parameters required for wireless LAN connection. For further details, see “Preparation for wireless LAN connection” on page 55.

■

Enter the network name (SSID) and other data.

■

Enter the network key (the key to be used to encode communications data).

3. Perform setting operations relating to network connection. For further details, see “Connection to the network” on page 57.

■

Specify TCP/IP as the protocol, and confirm the name of the work group and other settings.

■

Enter the data required for file/printer sharing on the network. Perform this operation as required.

■

For access point (infrastructure) connection, enter data for the access point. Refer to the manual of the access point for further details.

■

Verify that you have been able to connect your computer to the network.

PREPARATION FOR WIRELESS LAN CONNECTION

This section explains the preparation (parameter assignment) required for the use of the wireless LAN.

Assigning parameters

Enter the network name (SSID), the network key, and other data required for wireless LAN connection. If there is the administrator of the network, contact the network administrator for data settings.

■

To use access point (infrastructure) connection, refer to the access point manual for the access point-setting procedure.

■

If it is necessary to change the channel, change the setting of the access point. For the setting procedure, refer to the manual of the access point.

1. Right-click the Atheros Wireless Utility icon in the system tray in the lower right corner of your screen.

2. Click [Open Client Utility]. The [Atheros Wireless Configuration Utility] window will be displayed.

3. Select the [Profile Management] tab.

4. Click the [New] button. The Profile Management window will appear.

5. Enter the following information required to establish connection to the wireless LAN:

Profile Name

Enter a name for this configuration profile

Network names

Enter the appropriate SSID(s) of the wireless networks to which this device will connect. You have the option of entering up to three SSID’s.

6. Select the [Advanced] tab.

7. Choose appropriate Power Save Mode setting. Options are [Off], [Normal], and [Maximum]. [Normal] is the default setting.

8. Choose the appropriate type of network connection. Options are [Access Point] (same as infrastructure mode) and [AdHoc].

9. Select the [Security] tab.

WIreless LAN User’s Guide

10. Select the appropriate security method for your wireless network.

WPA

Choose the appropriate WPA EAP type - PEAP or TLS. Please see your network administrator for the appropriate configuration settings.

WPA-PSK

Enter the appropriate pre-shared key. Please see your network administrator for the appropriate configuration settings.

802.1x

Choose the appropriate 802.1x/EAP type: TLS, PEAP, or LEAP. Please see your network administrator for the appropriate configuration settings.

Pre-Shared Key

Same as Network Key or WEP Key. Entry methods include hexadecimal or ASCII text. If you wish to use ASCII characters, enter the network key in a string consisting of five or thirteen characters. The characters that can be used for the Network Key are: 0 - 9, A - Z, a - z, and _.

If you wish to use a hexadecimal number, enter the network key in a string consisting of 10 to 26 characters.The characters that can be used for the network key are: 0 - 9, A - F, and a - f. For ad hoc connections, enter the same network key for all computers connected to the network. For access point (infrastructure) connection, enter the value to match the access point. For information about the access point, refer to the access point manual.

3. Right-click [Local Area Connection], and click [Properties] in the menu displayed. The [Local Area Connection Properties] window will be displayed.

4. Click [Internet Protocol (TCP/IP] and then click [Properties]. The [Properties] window will be displayed.

5. Set the IP address:

■

For ad hoc connection

Select [Use the following IP address:], then enter data in [IP address] and [Subnet mask]. See page 69 for IP address setting.

■

For access point (infrastructure) connection

Select [Obtain an IP address automatically] and [Obtain DNS server address automatically].

Follow directions from the network administrator about IP address settings, DNS server setting, and the default gateway.

6. Click the [OK] button. Processing will return to the [Properties] window.

7. Click the [OK] button. If a message is displayed that requests you to restart the personal computer, click [Yes] and then restart the computer.

Confirming the computer and workgroup names

To modify the computer name and/or the workgroup name, you need to be logged in from Windows as an administrator.

1. Click [Start] -> [Settings] -> [Control Panel].

CONNECTION TO THE NETWORK

If there is the administrator of the network, contact the network administrator for data settings prior to connecting to the network.

Setting the network

Perform the “Setting TCP/IP” and “Confirming the computer and work group names” operations for network connection.

Setting TCP/IP

To change the setting of the IP address, you need to be logged in from Windows as an administrator.

1. Click the [Start] -> [Settings] -> [Control Panel].

2. Double-click the [Network and Dial-up Connections] icon. The [Network and Dial-up Connection] window will be displayed.

2. Double-click the [System] icon. The [System Properties] window will be displayed.

3. Click the [Network Identification] tab.

4. Confirm the settings of [Full computer name] and [Work group].

■

The setting of [Full computer name] denotes the name for identifying the computers on the network. Any name can be assigned. The computer name will be identified more easily if the model number, the user name, and other factors are already set.

■

[Workgroup] denotes the group name of the network.

5. To change the name, click [Properties], then proceed in accordance with the instruction messages displayed on the screen. Processing will return to the [System Properties] window.

LifeBook C Series Notebook - Section Five

For ad hoc connection:

Assign the same network name to all personal computers existing on the network.

For access point (infrastructure) connection:

Assign the name of the workgroup to be accessed.

6. Click the [OK] button. If a message is displayed that requests you to restart the personal computer, click [Yes].

Setting the sharing function

Set the sharing function to make file and/or printer sharing with other network-connected personal computers valid. The setting operation is not required unless the sharing function is to be used.

The folder and printer for which the sharing function has been set will be usable from any personal computer present on the network.

To share a file and/or the connected printer, you need to be logged in as an administrator.

Setting the Microsoft network-sharing service

1. Click [Start] -> [Settings] -> [Control Panel].

2. Double-click the [Network and Dial-up Connections] icon. The [Network and Dial-up Connections] window will be displayed.

3. Right-click [Local Area Connection], and click [Properties] in the menu displayed. The [Properties] window will be displayed.

4. If [File and Printer Sharing for Microsoft Networks] is displayed, proceed to step 5. If [File and Printer Sharing for Microsoft Networks] is not displayed, skip to step 6.

5. Make sure that the [File and Printer Sharing for Microsoft Networks] check box is checked, and then click the [OK] button. Skip to “Setting filesharing function” on page 58.

6. Click [Install]. The [Select Network Component Type] window will be displayed.

7. Click [Service], and then click the [Add] button. The [Select Network Service] window will be displayed.

8. Click [File and Printer Sharing for Microsoft Networks] and then click the [OK] button. Processing will return to the [Wireless Network Connection Properties] window, and [File and Printer Sharing for Microsoft Networks] will be added to the list.

9. Click the [OK] button.

Setting the file-sharing function

The procedure for setting the file-sharing function is laid down below taking the “work” folder within drive C as an example.

1. Double-click [My Computer] on the Desktop, and then double-click [Local Disk (C:)].

2. Right-click the “work” folder (or whichever folder you wish to share), and click [Sharing...] in the menu displayed. The [Properties] window will be displayed.

3. Select the [Sharing] tab if it isn’t already selected.

4. Select [Share this folder], then enter data as required:

■

“Share name”

Enter the name of the folder to be shared.

■

“Comment”

Enter explanatory statements or notes about the folder to be shared.

■

“User limit”

Enter the number of users who share the folder.

■

[Permissions]

Click the [Permissions] button to set permission levels for access to the folder.

■

[Caching]

Click the [Caching] button to configure settings for the off-line access to the folder.

5. Click the [OK] button. The folder will be set as a sharable folder, and the display of the icon for the “work” folder will change.

Setting the printer-sharing function

1. Click [Start] -> [Settings] -> [Printers]. A list of connected printers will be displayed.

2. Right-click the printer for which the sharing function is to be set, and then click [Sharing...] in the menu displayed. The property window corresponding to the selected printer will be displayed.

3. Click the Sharing tab if it is not already selected.

4. Check the [Shared as] checkbox and confirm the name of the printer to be shared or enter a new name. Click [OK]. Printer sharing will be set and the display of the icon for the printer will change.

Confirming connection

After you have finished the network setup operations, access the folder whose sharing has been set, and confirm the status of the radio in case of trouble such as a network connection failure.

WIreless LAN User’s Guide

In the case of an access point (infrastructure) connection, enter the necessary data for the access point before confirming connection. Refer to the manual of the access point for the access point setup procedure

Connecting your personal computer to another personal computer

1. Double-click [My Network Places] on the Desktop. The [My Network Places] window will be displayed.

2. Double-click the [Computers Near Me] icon. The

personal computers connected to the network will be listed.

3. Double-click the name of the personal computer to

which you wish to connect your own personal computer. The folder that specified in “Setting the filesharing function” on page 58 will be displayed.

4. Double-click the folder to be accessed. The contents

of the folder will be displayed.

Confirming the status of the radio

1. Right-click the Atheros icon in the lower right corner of the screen.

2. Click [Open Client Utility]. The Atheros Wireless

Configuration Utility window opens.

3. Contained within the Current Status tab and

Advanced Current Status, you will find the current operating status of the radio. (When the radio is turned off or the computer is not yet connected, some of the conditions will not be displayed.)

■

Profile Name

The current configuration profile is displayed.

■

Network Type - Configured Network Type

[Access Point] or [AdHoc] will be displayed.

■

Current Mode

Indicates the frequency and data rate currently used by the radio.

■

Current Channel

The channel number currently used by the radio.

■

Link Status

Displays the current connected state of the WLAN module.

■

Encryption Type

Displays the encryption type currently used by the radio.

■

IP Address

Displays the current TCP/IP address assigned to the WLAN adapter.

■

Country

The country with the country code for which the radio is configured.

■

Transmit Po wer Level

Displays the current transmit power level of the radio.

■

Network Name (SSID)

Displays the Network Name (SSID) currently used by the radio.

■

Power Save Mode

Displays the configured Power Save Mode currently used by the radio. [Off], [Normal], or [Maximum] will be displayed.

■

BSSID

Displays the Basic Service Set Identifier. This is typically the MAC address of the Access Point or in the case of AdHoc networks, is a randomly generated MAC address.

■

Frequency

Displays the center frequency currently being used by the radio.

■

Transmit Rate

Displays the current data rate used by the radio to transmit data.

■

Receive Rate

Displays the current data rate used by the radio to receive data.

LifeBook C Series Notebook - Section Five

Troubleshooting

Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table.

Problem Possible Cause Possible Solution

Unavailable network connection

Incorrect network name (SSID) or network key

Poor radio wave condition

Radio wave transmission has stopped

The computer to be connected is turned off

Ad hoc connection: verify that the network names (SSID’s) and network

keys (WEP) of all computers to be connected have been configured correctly. SSID’s and WEP key values must be identical on each machine.

Access Point (Infrastructure) connection: set the network name (SSID) and network key to the same values as those of the access point.

Set the Network Authentication value identically to that of the Access Point. Please consult your network administrator for this value, if necessary.

For the method of setting network authentication, refer to the following pages:· Windows XP: “Assigning parameters” on page 55· Windows 2000: “Assigning parameters” on page 60

Ad hoc connection: Retry connection after shortening the distance to the destination computer or removing any obstacles for better sight.

Access Point (Infrastructure) connection: Retry connection after shortening the distance to the access point or removing any obstacles for better sight.

To check the wave condition, refer to the following pages:· Windows XP: “Confirming the status of the radio waves” on page 59.· Windows 2000: “Confirming the status of the radio” on page 63

Check if the wireless switch is turned ON. Also verify “Disable Radio” is not checked in “Network setting” window. Refer to “Starting Transmission” on page 54.

Check if the computer to be connected is turned ON.

Active channel duplication due to multiple wireless LAN networks

No right of access to the network to be connected

Incorrectlyperformed network setting

Unmatched [Network authentication (shared mode)] settings in Windows XP

If there is any other wireless LAN network nearby, change channels to avoid active channel duplication. For the method of checking active channels, refer to the following pages:· Windows XP: “Confirming the status of the radio waves” on page 59· Windows 2000: “Confirming the status of the radio waves” on page 63

Check if you have a right of access to the network to be connected with.

Check the protocol, work group name or shared setting.

For the method of checking, refer to the following pages:· Windows XP: “Connection to the Network” on page 57· Windows 2000: “Connection to the Network” on page 61

If the setting of [Network authentication (shared mode)] is not matched with that of access point or computer to be connected with, no communication can be established. Check the parameter setting.Refer to “Assigning parameters” on page 55.

WIreless LAN User’s Guide

Problem Possible Cause Possible Solution

Unavailable network connection

(continued)

It takes too long to retrieve the network and display the connected computers.

Incorrect setting of IP address

Retrieve computers as follow:

Windows XP:

1. Click [Start] button, then click [Search].

2. Click [Computers or people].

3. Click [Computers on the network].

4. Input the name of computer to be connected with in [Computer name] and click [Search].

5. Double-click the icon of connected computer.·

Windows 2000:

1. Click [Start] -> [Find] -> [Files and folders].

2. Click [Computer] in [Find other items].

3. Input the name of computer to be connected with in [Computer name] and click [OK].

4. Double-click the icon of connected computer.

Check the network setting.

Windows XP: “Setting the network” on page 57.

Windows 2000: “Setting the network” on page 61

In case of using TCP/IP protocol, you can check IP address as follows:

1. Windows XP:

Click [Start] -> [All programs] -> [Accessories] -> [Command prompt].·

Windows 2000:

Click [Start] button -> [Program] -> [Accessories] -> [Command prompt].

2. In [Command prompt] or [MS-DOS prompt] window, input

[IPCONFIG] command as follows, then press [Enter] key.

Example: In case of C drive being the hard disk: C:\ipconfig [Enter]

Check that the IP address is correctly displayed:.

IP Address................: 10.0.1.3

Subnet Mask.............: 255.255.255.0

Default Gateway.........: 10.0.1.1

When IP address is displayed as [169.254.XXX.YYY] or [0.0.0.0], IP address is not correctly fetched from the access point. In that case, restart the computer itself. If the display is still unchanged, check the setting of TCP/IP.

If [Cable Disconnected] or [Media Disconnected] is displayed without showing IP address, check the setting of network name (SSID) and network key. Also, set the network authentication according to the access point.

LifeBook C Series Notebook - Section Five

Problem Possible Cause Possible Solution

Communication is disconnected soon after connection to the access point

Access control may be disabled

In case of Windows XP, check the setting of “Enable network access control using IEEE 802.1X”.Refer to “Assigning parameters” on page 55.

When restricting the access of wireless LAN clients using IEEE802.1X authentication, put a check mark on “Enable network access control using IEEE 802.1X”.

When using at home, remove a check mark on “Enable network access control using IEEE802.1X”.

For the method of setting related with IEEE802.1X authentication, refer to the access point manual.

Wireless LAN Glossary

Ad hoc

A designation for wireless LAN network configuration. It indicates a form of communication limited to those personal computers which have wireless LAN function. For details, refer to “Ad hoc connection” on page 52.

Channel

The frequency band of wireless LAN to be used in communications over wireless LAN or at the access point.

DHCP (Dynamic Host Configuration Protocol)

A protocol used for automatically fetching communication parameters such as IP addresses. The side which assigns IP address is called DHCP server and the side that is assigned it is called DHCP client.

DNS (Domain Name System)

A function that controls the correspondence of IP addresses assigned to a computer with the name. Even for those computers whose IP addresses are unknown, if their names are known, it is possible to communicate with them.

IEEE802.11a

One of the wireless LAN standards prescribed by the 802 committee in charge of establishing standards of LAN technology in IEEE (Institute of Electrical and Electronic Engineers). It allows communications at the maximum speed of 54 Mbps by using a 5GHz band which can freely be used without radio communication license.

IEEE802.11b

One of the wireless LAN standards prescribed by 802 committee in charge of establishing standards of LAN technology in IEEE (Institute of Electrical and Electronic Engineers). It allows communications at the maximum speed of 11Mbps by a band of 2.4 GHz (ISM band) which can freely be used without radio communication license.

WIreless LAN User’s Guide

the world. A private address is a unique address within a closed network.

LAN (Local Area Network)

An environment connecting computers within a relatively small range, such as the same floor and building.

MAC address (Media Access Control Address)

A physical address inherent to a network card. For Ethernet, the top three bytes are controlled/assigned as a vendor code. The remaining three bytes comprise the code uniquely (to avoid duplication) controlled by each vendor. As a result, there is no Ethernet card with the same physical address in the world. In Ethernet, the frame transmission/reception is performed based on this address.

MTU (Maximum Transmission Unit)

The maximum size of data which can be transmitted at one time in networks including the Internet. In an environment whose maximum size of data is too large to correctly receive data, normal communications can be restored by setting the size of MTU to a smaller value.

Network authentication

The method of authentication performed by wireless LAN clients to connect with the access point. There are two types: open system authentication and shared key authentication. The type of authentication must be set to each client and also coincide with the setting of access point with which to communicate. Network authentication is sometimes called authentication mode.

Network key

Data that is used for encrypting data in data communication. The personal computer uses the same network key both for data encryption and decryption, therefore, it is necessary to set the same network key as the other side of communication.

Network name (SSID: Security Set Identifier)

Access point

A designation of Wireless LAN network configurations. It indicates a form of communication using an Access Point. For details, refer to “access point connection” on page 52.

IP address

An address used by computers for communicating in TCP/IP environment. IP addresses have global and private addresses. A global address is a unique address in

When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. This grouping is performed with “Network name (SSID)”. In order to improve security, the network key is set allowing no communication unless “Network name (SSID)” coincides with the network key.

Open system authentication

One of network authentication types for wireless LAN. Since there is no check of network key upon authentication, clients can connect to the access point without

LifeBook C Series Notebook - Section Five

submitting correct network keys. However, in case of actual communications, the same network key must be set. Open system authentication is sometimes called Open key authentication.

PPPoE (Point to Point Protocol over Ethernet)

A method of allowing the authentication protocol adopted in telephone line connection (PPP) to be used over an Ethernet.

Protocol

A procedure or rule of delivering data among computers. Ordered data communication is allowed by making all conditions required for communication including the method of data transmission/reception and actions upon communication errors into procedures.

Shared key authentication

One of the network authentication types for wireless LAN. Upon authentication, the access point checks whether the same network key is set to the client. If the client uses a wrong network key or the network key itself is not set, authentication is unsuccessful, allowing no communications with the access point.

SSID (Security Set Identifier)

See “Network name”

Subnet mask

TCP-IP network is controlled by being divided into multiple smaller networks (subnets). IP address consists of the subnet address and the address of each computer. Subnet mask defines how many bits of IP address comprise the subnet address. The same value shall be set among computers communicating with each other.

TCP/IP (Transmission Control Protocol/Internet Protocol)

A standard protocol of the Internet.

Wi-Fi

Indicates that the interconnectivity test of the organization which guarantees the compatible connection of wireless LAN (Wi-Fi Alliance) has been passed.

IP address information

IP addressing is much more complicated than can be briefly explained in this document. You are advised to consult with your network administrator for additional information.

If IP address is unknown, set IP address as follows:

If you have an access point (DHCP server) on the network, set the IP address as follows:

Windows 2000: [Obtain an IP address automatically]

Windows XP: [Obtain an IP address automatically]

A DHCP server is a server that automatically assigns IP addresses to computers or other devices in the network. There is no DHCP server for the AdHoc network.

If the IP address is already assigned to the computer in the network, ask the network administrator to check the IP address to be set for the computer.

WIreless LAN User’s Guide

If no access point is found in the network:

An IP address is expressed with four values in the range between 1 and 255.

Set the each computer as follows: The value in parentheses is a subnet mask.

Computer A: 192.168.100.2 (255.255.255.0)

Computer B: 192.168.100.3 (255.255.255.0)

Computer C: 192.168.100.4 (255.255.255.0)

Computer X: 192.168.100.254 (255.255.255.0)

LifeBook C Series Notebook - Section Five

Specifications

Item Specification

Type of network Conforms to IEEE 802.11b/802.11g (Wi-Fi based)*

Transfer rate (Automatic switching) 54 Mbps maximum data rate

Active frequency 2400~2473MHz

Number of channels 11 channels, 3 non-overlapping channels

Security Network name (SSID)

Maximum recommended number of computers to be connected over wireless LAN (during ad hoc connection)

* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed.

** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/ 104 bits after subtracting the fixed length of 24 bits.

*** Depending on practical environments, the allowable number of computers to be connected may be decreased.

Network key (64 bits/128 bits)**

10 units or less ***

Troubleshooting

LifeBook C Series Notebook – Section Six

Troubleshooting

Your LifeBook notebook is sturdy and subject to few problems in the field. However, you may encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices that you can solve by replacing the device. The information in this section helps you isolate and resolve some of these straightforward problems and identify failures that require service.

IDENTIFYING THE PROBLEM

If you encounter a problem, go through the following procedure before pursuing complex troubleshooting:

1. Turn off your LifeBook notebook.

2. Make sure the AC adapter is plugged into your LifeBook notebook and to an active AC power source.

3. Make sure that any card installed in the PC Card slot is seated properly. You can also remove the card from the slot, thus eliminating it as a possible cause of failure.

4. Make sure that any devices connected to the external connectors are plugged in properly. You can also disconnect such devices, thus eliminating them as possible causes of failure.

5. Turn on your LifeBook notebook. Make sure it has been off at least 10 seconds before you turn it on.

6. Go through the boot sequence.

7. If the problem has not been resolved, refer to the Troubleshooting Table that follows for more detailed

troubleshooting information.

■

If you keep notes about what you have tried, your support representative may be able to help you more quickly by giving additional suggestions over the phone.

■

Do not return a failed LifeBook notebook to your supplier until you have talked to a support representative.

8. If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative:

Toll free: 1-800-8Fujitsu (1-800-838-5487) Fax: 408-764-2724 E-mail: 8fujitsu@us.fujitsu.com/computers Web site: http://us.fujitsu.com/computers.

Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:

■

Product name

■

Product configuration number

■

Product serial number

■

Purchase date

■

Conditions under which the problem occurred

■

Any error messages that have occurred

■

Hardware configuration

■

Type of device connected, if any

See the Configuration Label on the bottom of your LifeBook notebook for configuration and serial numbers. (See Figure 2-7 on page 12 for location)

SPECIFIC PROBLEMS

Using the Troubleshooting Table

When you have problems with your LifeBook notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your LifeBook notebook.

LifeBook C Series Notebook – Section Six

TROUBLESHOOTING TA BL E

Problem Page

Audio Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 74

Optical Drive Problems . . . . . . . . . . . . . . . . . . . . page 74

Floppy Disk Drive Problems . . . . . . . . . . . . . . . . page 75

Hard Drive Problems . . . . . . . . . . . . . . . . . . . . . . page 75

Keyboard or Mouse Problems. . . . . . . . . . . . . . . page 76

Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . page 76

Modem Problems. . . . . . . . . . . . . . . . . . . . . . . . . page 76

Problem Possible Cause Possible Solutions

Audio Problems

Problem Page

USB Device Problems . . . . . . . . . . . . . . . . . . . . . page 76

PC Card Problems . . . . . . . . . . . . . . . . . . . . . . . . page 77

Power Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . page 77

Shutdown and Startup Problems . . . . . . . . . . . . page 79

Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 79

Miscellaneous Problems . . . . . . . . . . . . . . . . . . . page 81

There is no sound coming from the builtin speakers.

Optical Drive Problems

LifeBook notebook fails to recognize media discs.

The software volume control is set too low.

Headphones are plugged into your LifeBook notebook.

Adjust the sound volume control settings in your software, operating system and applications.

Plugging in headphones disables the built-in speakers, remove the headphones.

BIOS audio settings are incorrect. Set the BIOS setup utility to the default values within

the Multimedia Device Configuration menu. (See

BIOS Setup Utility on page 27 for more information)

Software driver is not configured correctly.

The disc is not pushed down onto raised center circle of the drive.

Media player tray is not latched shut.

Setup utility is set to something other than media player or Auto for Secondary Master Controller.

Wrong drive designator was used for media player in the application.

Refer to your application and operating system documentation for help.

Open media player tray and re-install the media disc properly.

Push on the front of the media player tray until it latches.

Revise BIOS settings for the Secondary Master Controller. (See BIOS Setup Utility on page 27 for

more information)

Verify the drive designator used by the application is the same as the one used by the operating system. When the operating system is booted from a media player, drive designators are automatically adjusted.

Windows Media Player auto insert notification function is disabled.

Start the media player from the desktop or application software or re-enable the Windows media player auto insert notification function.

The Media Player Access indicator on the Status Indicator Panel blinks at regular intervals when no disc is in the tray or the media drive is not installed.

Media disc is dirty or defective. Wipe the disc with a non-abrasive CD cleaning cloth

and reinsert. It if still will not work try another media disc in the drive.

The Windows media player auto

This is normal. insert notification function is active and is checking to see if a media disc is ready to run.

Problem Possible Cause Possible Solutions

The media player will not play international DVD titles

The LifeBook notebook fails to Auto-Play a DVD movie.

Floppy Disk Drive Problems

The region code for the DVD does not match that of the media player.

The media player software has not been installed.

Troubleshooting

All Fujitsu notebook DVD players are set to play

DVD titles with region code number 1, which is

specified for the North American market. The

region number is a regional restriction code defined

by the DVD Forum acting on the requirements of

Hollywood. Different region codes are recorded on

video DVD titles for publication in different areas of

the world. If the regional code of the DVD player

does not match the regional codes on the titles, then

playback is impossible.

NOTE: You can change the region code on the DVD

player using the Properties menu of the DVD soft-

ware. Note, however, that you can only change the

region code up to four times. After the fourth

change, the last region code entered becomes

permanent, and cannot be changed.

Locate and install the DVD-ROM Applications CD.

You cannot access your floppy disk.

Hard Drive Problems

You cannot access your hard drive.

You tried to write to a write protected floppy disk.

Floppy disk is not loaded correctly.

BIOS setup utility states Floppy

Disk Controller: Disabled.

Security is set to protect access to floppy disk data.

The setup utility is incorrectly set for your internal (Primary Master) or optional second hard drive (Primary Slave).

The wrong drive designator was used by an application when a bootable CD-ROM was used to start the LifeBook notebook.

Security is set so your operating system cannot be started without a password.

Eject the floppy disk and set it to write enable. (See

Internal Floppy Disk Drive on page 37 for more infor-

mation)

Eject floppy disk, check orientation and re-insert.

(See Internal Floppy Disk Drive on page 37 for more

information)

Revise the setup utility Main menu settings to

enable Diskette Controller. (See BIOS Setup Utility

on page 27 for more information)

Verify your password and security settings.

Revise BIOS settings to set both Primary Master

and Primary Slave correctly. (See BIOS Setup Utility

on page 27 for more information)

Verify drive designator used by application is in

use by the operating system. When the operating

system is booted from a CD, drive designations

are automatically adjusted.

Verify your password and security settings.

LifeBook C Series Notebook – Section Six

Problem Possible Cause Possible Solutions

Keyboard or Mouse Problems

The built-in keyboard does not seem to work.

The LifeBook notebook has gone into Suspend mode.

Push the Power/Suspend/Resume button.

You have installed an external keyboard or mouse, and it does not seem to work.

You have connected an external keyboard or a mouse and it seems to be locking up the system.

Memory Problems

Your Info menu of the BIOS setup utility information, does not show the correct amount of installed memory.

Your application has locked out your keyboard.

Try to use your integrated pointing device to restart

your system. If this fails, turn your LifeBook note-

book off press the Power/Suspend/Resume button

for 10 seconds or more, and then turn it back on.

Your external device is not properly installed.

Your operating system software is not set up with the correct

Re-install your device. (See Device Ports on page 46

for more information)

Check your device and operating system docu-

mentation and activate the proper driver. software driver for that device.

Your operating system software is not set up with the correct

Check your device and operating system

documentation and activate the proper driver. software driver for that device.

Your system has crashed. Try to restart your LifeBook notebook. If this fails,

turn your LifeBook notebook off press the Power/

Suspend/Resume button for 10 seconds or more,

and then turn it back on.

Your memory upgrade module is not properly installed.

Remove and re-install your memory upgrade

module. (See Memory Upgrade Module on page 44

for more information)

You have a memory failure. Check for Power On Self Test (POST) messages.

(See Power On Self Test Messages on page 82 for more

information)

Modem Problems

Messages about modem operation.

Messages about modem operation are generated by whichever modem application is in use.

USB, Parallel, or IR Device Problems

You have installed a USB, parallel, or IR device. Your LifeBook notebook does not recognize the device, or the device does not seem to work properly.

The device is not properly installed.

The device may have been installed while an application was running, so your LifeBook is not aware of its installation.

Your software may not have the correct software driver active.

See your application software documentation for

additional information.

Remove and re-install the device. (See Device Ports

on page 46 for more information)

Close the application and restart your LifeBook

notebook.

See your software documentation and activate the

correct driver.

Problem Possible Cause Possible Solutions

You have installed a USB, parallel, or IR device. Your LifeBook notebook does not recognize the device, or the device does not seem to work properly.

PC Card Problems

A card inserted in the PC Card slot does not work o r is locking up the system.

Troubleshooting

You m ay h av e th e w ro ng I/ O address selected for your device.

See your device documentation and software docu-

mentation to determine the required I/O address.

Change the settings in the BIOS setup utility. (See

Figure on page 27 for location)

Your device and another device are assigned the same I/O address.

Check all I/O addresses located within the BIOS

setup utility and any other installed hardware or

software to make sure there are no duplications.

Parallel port is set to output only. Check parallel port setting in the BIOS and set to

bi-directional or ECP.

The card is not properly installed. Remove and re-install the card. (See PC Cards on

page 43 for more information)

The card may have been installed while an application was running,

Close the application and restart your LifeBook

notebook. so your LifeBook notebook is not aware of its installation.

Your software may not have the correct software driver active.

See your software documentation and activate the

correct driver.

Power Failures

You turn on your LifeBook notebook and nothing seems to happen.

You m ay h av e th e w ro ng I/ O address selected for your PC Card device.

See your PC Card documentation to determine

the required I/O address. Change the settings in

the BIOS. (See BIOS Setup Utility on page 27 for

more information)

Your PC Card device and another device are assigned the same I/O address.

The card may have been “removed” using the Unplug or Eject Hardware utility.

Check all I/O addresses located within the BIOS

setup utility and any other installed hardware or

software to make sure there are no duplications.

If the Unplug or Eject Hardware utility has been

used to “remove” the PC card, the system will not

recognize the card, even if it is still present in the

slot. Physically remove the card and reinstall it in the

slot. If that is not successful, reboot the system.

The installed primary battery is completely discharged, there is no optional second battery installed or there is no power adapter (AC

Check the Status Indicator Panel to determine the

presence and condition of the batteries. (See Status

Indicator Panel on page 13 for more information)

Install a charged battery or a power adapter. or Auto/Airline) installed.

The primary battery is installed but is faulty.

Use the Status Indicator panel to verify the presence

and condition of the batteries. (See Status Indicator

Panel on page 13 for more information) If a battery is

indicating a short, remove that battery and operate

from another power source or replace that battery.

The battery or batteries are low. Check the Status Indicator Panel to determine the

presence and condition of the batteries. (See Status

Indicator Panel on page 13 for more information) Use

a power adapter to operate until a battery is charged

or install a charged battery.

LifeBook C Series Notebook – Section Six

Problem Possible Cause Possible Solutions

You turn on your LifeBook notebook and nothing seems to happen.

(continued)

The power adapter (AC or auto/ airline) is not plugged in properly.

The power adapter (AC or auto/ airline) has no power from the AC outlet, airplane seat jack, or the car’s cigarette lighter.

The power adapter (AC or auto/ airline) is faulty.

Verify that your adapter is connected correctly. (See

Power Sources on page 25 for more information)

Move the AC cord to a different outlet, check for a

line switch or tripped circuit breaker for the AC

outlet. If you are using an auto/airline adapter in a

car make sure the ignition switch is in the On or

Accessories position.

Try a different power adapter or install a charged

optional second battery.

Your LifeBook notebook turns off all by itself.

Your LifeBook notebook will not work on battery alone.

The power management parameters are set for auto timeouts which are too short for your operating needs.

Press any button on the keyboard, or move the

mouse to restore operation. If that fails, push the

Power/Suspend/Resume button. Check your power

management settings, or close your applications and

go to the Power Options menu of the setup utility to

adjust the timeout values to better suit your

operation needs.

You are operating on battery power only and have ignored a low battery alarm until the

Install a power adapter or a charged battery, then

push the Power/Suspend/Resume button. (See Power

Sources on page 25 for more information)

batteries are all at the dead battery state and your machine has gone into Dead Battery Suspend mode.

You have a battery failure. Verify the condition of the batteries using the Status

Indicator Panel, and replace or remove any batteries

that are shorted. (See Status Indicator Panel on

page 13 for more information)

Your power adapter has failed or lost its power source.

Make sure the adapter is plugged in and the outlet

has power.

The installed battery is dead. Replace the battery with a charged one or install a

power adapter.

No battery is installed. Install a charged battery.

The battery is improperly installed.

Verify that the battery is properly connected by re-

installing it.

The battery seems to discharge too quickly.

Your installed battery is faulty. Verify the condition of the battery using the Status

Indicator panel and replace or remove any battery

that is shorted. (See Status Indicator Panel on page 13

for more information)

You are running an application that uses a great deal of power

Use both the primary battery and/or use a power

adapter for this application when at all possible. due to frequent hard drive or media player drive access, use of a modem card or a LAN PC card.

The power savings features may be disabled.

Check the power management and/or setup utility

settings in the Power Options menu and adjust

according to your operating needs.

The brightness is turned all the way up.

Turn down the brightness adjustment. The higher

the brightness the more power your display uses.

Problem Possible Cause Possible Solutions

The battery seems to discharge too quickly. (continued)

The battery is very old. Replace the battery.

The battery has been exposed to high temperatures.

The battery is too hot or too cold. Restore the LifeBook to normal operating tempera-

Shutdown and Startup Problems

Troubleshooting

Replace the battery.

ture. The Battery Charging icon on the indicator

panel will flash when the battery is outside operating

range.

The Power/Suspend/ Resume button does not work.

The system powers up and displays power-on information, but fails to load the operating system.

An error message is displayed during the LifeBook notebook (boot) sequence.

The Power/Suspend/Resume button is disabled from the Advanced submenu of the Power menu of the setup utility.

You did not hold the button in long enough.

There may be a conflict with the application software.

The boot sequence settings of the setup utility are not compatible with your configuration.

You have a secured system requiring a password to load your operating system.

Internal hard drive was not detected.

Power On Self Test (POST) has detected a problem.

Enable the button from the setup utility.

Hold the button longer. This may need to be a few

seconds if your application is preventing the CPU

from checking for button pushes.

Close all applications and try the button again.

Set the operating source by pressing the [ESC] key

while the Fujitsu logo is on screen or use the [F2]

key and enter the setup utility and adjust the source

settings from the Boot menu. (See BIOS Setup

Utility on page 27 for more information)

Make sure you have the right password. Enter the

setup utility and verify the Security settings and

modify them as accordingly. (See BIOS Setup Utility

on page 27 for more information)

Use the BIOS setup utility or Primary Master

submenu, located within the Main menu, to try to

auto detect the internal hard drive.

See Power On Self Test (POST) messages to deter-

mine the meaning of the problem. Not all messages

are errors; some are status indicators. (See Power On

Self Test Messages on page 82 for more information)

Your LifeBook notebook appears to change setup parameters when you start it.

Video Problems

Display is blank when you turn on the system.

BIOS setup changes were not saved when you made them and exited the BIOS setup utility returning it to previous settings.

The BIOS CMOS hold-up battery has failed.

Something is pushing on the Closed Cover switch.

Make sure you select Save Changes And Exit when

exiting the BIOS setup utility.

Contact your support representative for repairs.

This is not a user serviceable part but has a normal

life of 3 to 5 years.

Clear the Closed Cover switch. (See Figure 2-3 on

page 8 for location)

LifeBook C Series Notebook – Section Six

Problem Possible Cause Possible Solutions

Display is blank when you turn on the system.

The LifeBook notebook is set for an external monitor only.

(continued)

Pressing [F10] while holding down the [Fn] key

allows you to change the destination of your display

video. Each time you press the combination of keys

you will step to the next choice. The choices, in

order, are: built-in display only, external monitor

only, both built-in display and external monitor.

When the ATI Driver CD is first installed, you receive a Microsoft message informing you that the ATI driver is not compatible with your operating system.

The LifeBook notebook turned on with a series of beeps and your builtin display is blank.

The display goes blank by itself after you have been using it.

The angle and brightness settings of the display are not adequate for the lighting conditions.

The power management timeouts may be set for very short intervals and you failed to notice the display come on and go off again.

The warning does not apply to your LifeBook; the driver has been thoroughly tested and its installation will not jeopardize the performance of your system.

Power On Self Test (POST) has detected a failure which does not allow the display to operate.

The LifeBook notebook has gone into Video timeout, Standby mode, Suspend mode or Hibernation (Save-to-Disk) mode because you have not used it for a period of time.

Move the display and the brightness control until

you have adequate visibility.

Press any button on the keyboard, or move the

mouse to restore operation. If that fails, push the

Power/Suspend/Resume button. (The display may

be shut off by Standy mode, Auto Suspend or Video

Timeout)

If this message appears on your screen, click the

Continue Anyway or Ye s buttons to proceed.

Contact your support representative.

Press any button on the keyboard, or move the mouse

to restore operation. If that fails, push the Power/

Suspend/Resume button. Check your power manage-

ment settings, or close your applications and go to the

Power Savings menu of the setup utility to adjust the

timeout values to suit your operation needs. (See

BIOS Setup Utility on page 27 for more information)

The built-in display does not close.

The built-in display has bright or dark spots.

Something is pushing on the Closed Cover switch.

The power management timeouts may be set for very short intervals and you failed to notice the display come on and go off again.

A foreign object, such as a paper clip, is stuck between the display and the keyboard.

If the spots are very tiny and few in number, this is normal for a large LCD display.

If the spots are numerous or large enough to interfere with your operation needs.

Check the Closed Cover switch. (See Figure 2-3 on

page 8 for location)

Press any button on the keyboard, or move the mouse

to restore operation. If that fails, push the Power/

Suspend/Resume button. (The display may be shut

off by Standby Mode, Auto Suspend or Video

Timeout)

Remove all foreign objects from the keyboard.

This is normal; do nothing.

Display is faulty; contact your support representative.

Problem Possible Cause Possible Solutions

The application display uses only a portion of your screen and is surrounded by a dark frame.

You are running an application that does not support 800 x 600/ 1024 x 768 pixel resolution display and display compression is enabled.

Troubleshooting

Display compression gives a clearer but smaller

display for applications that do not support 800 x

600 /1024 x 768 pixel resolution. You can fill the

screen but have less resolution by changing your

display compression setting, (See the Video Features

submenu, located within the Advanced menu of the

BIOS. (See BIOS Setup Utility on page 27 for more

information)

The Display is dark when on battery power.

You have connected an external monitor and it does not display any information.

You have connected an external monitor and it does not come on.

The Properties sec tion of the Intel Graphics Technology window displays an incorrect amount of Video RAM present.

Miscellaneous Problems

An error message is displayed on the screen during the operation of an application.

The BatteryAid default is set on low brightness to conserve power.

Your BIOS setup is not set to enable your external monitor.

Your external monitor is not properly installed.

Your operating system software is not set up with the correct software driver for that device.

Your external monitor is not compatible with your LifeBook notebook.

This is not a problem; it is a result of UMA technology.

Application software often has its own set of error message displays.

Press [Fn] + [F7] to increase brightness or double-

click on BatteryAid gauge and adjust Power Control

under battery settings.

Toggle the video destination by pressing [Fn] and

[F10] together, or check your BIOS setup and enable

your external monitor. (See Video Features submenu,

located within the Advanced Menu of the BIOS. (See

BIOS Setup Utility on page 27 for more information)

Reinstall your device. (See External Monitor Port on

page 47 for more information)

Check your device and operating system

documentation and activate the proper driver.

See your monitor documentation and the External

Monitor Support portions of the Specifications

section.

The Intel graphics chipset uses Unified Memory

Architecture (UMA) which allows the video chipset

to share up to 128 MB of the system’s main memory.

The amount being used will vary with the system

needs, and the amount of video RAM indicated will

vary as well.

See your application manual and help displays

screens for more information. Not all messages are

errors some may simply be status.

LifeBook C Series Notebook – Section Six

POWER ON SELF TEST MESSAGES

The following is an alphabetic list of error-and-status messages that BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. The most common errors are marked with a #. If an error message is displayed, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.

nnnn Cache SRAM Passed

Where nnnn is the amount of system cache in kilobytes successfully tested by the Power On Self Test. (This can only appear if you have an SRAM PC Card installed.)

*Diskette drive A error or Diskette drive B error

Drive A: or B: is present but fails the BIOS Power On Self Test diskette tests. Check to see that the drive is defined with the proper diskette type in the Setup Utility, (See BIOS Setup Utility on page 27 for more information) and that the diskette drive is installed correctly. If the disk drive is properly defined and installed, avoid using it and contact your support representative.

*Extended RAM Failed at offset: nnnn

Extended memory not working or not configured properly. If you have an installed memory upgrade module, verify that the module is properly installed. If it is properly installed, you may want to check your Windows Setup to be sure it is not using unavailable memory until you can contact your support representative.

nnnn Extended RAM Passed

Where nnnn is the amount of memory in kilobytes successfully tested.

*Failing Bits: nnnn The hex number nnnn

This is a map of the bits at the memory address (in System, Extended, or Shadow memory) which failed the memory test. Each 1 (one) in the map indicates a failed bit. This is a serious fault that may cause you to lose data if you continue. Contact your support representative.

*Fixed Disk x Failure or Fixed Disk Controller Failure (where x = 1-4)

The fixed disk is not working or not configured properly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue. Contact your support representative.

*Incorrect Drive A type – run SETUP

Type of floppy drive A: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.

*Incorrect Drive B type – run SETUP

Type of floppy drive B: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.

*Invalid NVRAM media type

Problem with NVRAM access. In the unlikely case that you see this message you may have some display problems. You can continue operating but should contact your support representative for more information.

*Keyboard controller error

The keyboard controller test failed. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.

*Keyboard error

Keyboard not working. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.

*Keyboard error nn

BIOS discovered a stuck key and displays the scan code for the stuck key. You may have to replace your keyboard but may be able to use an external keyboard until then. Contact your support representative.

*Monitor type does not match CMOS – Run SETUP

Monitor type not correctly identified in Setup. This error probably means your BIOS is corrupted, run the setup utility and set all settings to the default conditions. If you still get this error, contact your support representative.

#*Operating system not found

Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:. If the setup utility is correctly set, your hard drive may be corrupted and your system may have to be re-installed from your back up media.

Troubleshooting

*Parity Check 1 nnnn

Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data-destroying failure. Contact your support representative.

*Parity Check 2 nnnn

Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data-destroying failure. Contact your support representative.

#*Press <F1> to resume, <F2> to SETUP

Displayed after any recoverable error message. Press the [F1] key to continue the boot process or the [F2] key to enter Setup and change any settings.

#*Previous boot incomplete – Default configuration used

Previous Power On Self Test did not complete successfully. The Power On Self Test will load default values and offer to run Setup. If the previous failure was caused by incorrect values and they are not corrected, the next boot will likely fail also. If using the default settings does not allow you to complete a successful boot sequence, you should turn off the power with the Power/Suspend/ Resume button and contact your support representative.

*Real time clock error

Real-time clock fails BIOS test. May require board repair. Contact your support representative.

*Shadow RAM Failed at offset: nnnn

Shadow RAM failed at offset nnnn of the 64k block at which the error was detected. You are risking data corruption if you continue. Contact your support representative.

nnnn Shadow RAM Passed

Where nnnn is the amount of shadow RAM in kilobytes successfully tested.

*System battery is dead – Replace and run SETUP

The BIOS CMOS RAM memory hold up battery is dead. This is part of your BIOS and is a board mounted battery which requires a support representative to change. You can continue operating but you will have to use setup utility default values or reconfigure your setup utility every time you turn off your LifeBook notebook. This battery has an expected life of 2 to 3 years.

System BIOS shadowed

System BIOS copied to shadow RAM.

*System CMOS checksum bad – run SETUP

BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. Run Setup and reconfigure the system.

*System RAM Failed at offset: nnnn

System memory failed at offset nnnn of in the 64k block at which the error was detected. This means that there is a fault in your built-in memory. If you continue to operate, you risk corrupting your data. Contact your support representative for repairs.

nnnn System RAM Passed

Where nnnn is the amount of system memory in kilobytes successfully tested.

*System timer error

The timer test failed. The main clock that operates the computer is faulty. Requires repair of system board. Contact your support representative for repairs.

UMB upper limit segment address: nnnn

Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager.

Video BIOS shadowed

Video BIOS successfully copied to shadow RAM.

EMERGENCY OPTICAL DRIVE TRAY RELEASE

If for some reason the eject button fails, you can open the optical drive tray with a paper clip or similar tool inserted into the eject hole in the far right side of the front of the tray. Straighten one side of a paper clip and push it gently into the hole. The tray will pop out.

MODEM RESULT CODES

The operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem. The operating system and application software may suppress display of the result codes.

Examples of result codes are:

■

NO CARRIER

■

NO DIALTONE

■

CONNECT 53000 (Connection complete at 53 Kbps.)

■

ERROR

■

FAX

■

RING (This means an incoming call.)

■

BUSY

■

NO ANSWER

When using the internal modem with applications that are not factory installed refer to the application documentation.

LifeBook C Series Notebook – Section Six

RESTORING YOUR PRE-INSTALLED SOFTWARE

The Drivers and Applications Restore (DAR) CD contains:

■

Sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your LifeBook notebook configuration for use as documented below.

■

A link to the Drive Image Special Edition (DISE) utility on your hard disk drive.

■

Read-me files that provide additional use information for items on this CD-ROM.

If the DAR CD is in the drive when you boot up the system, a message will appear informing you that continuing to boot from the CD will overwrite all information on the hard drive, including saved files, and restore the hard drive to its factory configuration. If you wish to install drivers or applications only from the CD, remove the disk from the drive, reboot the system, and insert the CD after Windows has started.

If you have access to the internet, visit the Fujitsu Support web site at http://us.fujitsu.com/computers to check for the most current information, drivers and hints on how to perform recovery and system updates.

Creating a Backup Image

You can create a backup image of your C:\ drive at any time. The C:\ partition must be a FAT, FAT32, or NTFS partition. The backup partition must be installed directly after the C:\ partition on your hard disk (i.e., it should be the D:\ partition).

There are two ways to implement the DISE utility: When booting up the system, or from the desktop.

Creating a backup image when booting up

Before creating a backup image at boot-up, you must first change the boot-up priority so that the system will go to the CD drive first, rather than trying to boot-up from the hard drive or a floppy disk drive.

1. Power up your system and insert the DAR CD into the drive. Reboot your system.

2. When the prompt appears below the Fujitsu logo, press the [F12] key.

3. Select the CD drive from the list that appears, and press [Enter]. The CD drive is now the boot drive, and the system boots up from the CD.

4. A message will appear informing you that continuing to boot from the CD will overwrite all information on the hard drive, including saved files, and restore the hard drive to its factory configuration. When you are asked if you want to restore the factory image, click [Y]es. You will be presented with two options: [Create New Backup] and [Restore Backup].

DRIVE IMAGE SPECIAL EDITION (DISE)

PowerQuest Drive Image Special Edition (DISE) provides a way to restore your computer if you experience a hard dis k cra sh or other sy stem failu re. Fu jitsu has used DISE to create an image of everything installed on the computer at the time you purchased it. The image is saved on a separate partition on the hard disk. You can use DISE to restore the factory image and return your computer to the state in which it was shipped from Fujitsu.

Although it is not necessary, you can use DISE to store additional image files that you create. For example, if you install several applications and save data files on your hard disk, you can create a new image file that includes them and then save that image file on the hard disk. Then, in the event of a hard disk failure, you can restore the image that includes the applications and data

files you use.

Using the DISE feature will reduce the amount of usable disk space on your hard disk drive.

Click [Create New Backup] and follow the on- screen instructions. By selecting [Create New Backup], a new image will be written to your backup partition. This does not overwrite the old image, it creates a new one alongside the old one.

5. When complete, you will be prompted to reboot your system.

Creating a backup image from the desktop

To create a backup image from the desktop, select Drive Image SE from the Program list. You will initially be prompted to create a backup diskette. It is not necessary to create the backup diskette, since the DAR CD performs the same function, but you can make a backup diskette if you wish to have a redundant copy.

1. At the Drive Image Special Edition main screen, click Options> Create New Backup. DISE displays a warning that it must go to DOS to create the image.

2. Click Ye s .

DISE creates an image file in the backup partition. If you created a backup image previously, the new image overwrites the old one.

Enlarging the Backup Partition

If there is not enough unused space in the backup partition on your hard disk, DISE will resize the partition. DISE will display the minimum, maximum, and recommended sizes for the backup partition. You choose the size you want.

DISE takes the space from the FAT, FAT32, or NTFS partition that you are backing up. If there is not enough unused space in that partition to take, you will not be able to resize the backup partition and create an image file. You can delete files from the FAT, FAT32, or NTFS partition to create more unused space on the hard disk.

Restoring a Backup Image

You can restore either a factory image or a backup image you created. Be aware that restoring a backup image will replace the contents of the C:\ partition with the image you restore.

1. Disable virus protection software. If virus protection software is enabled, DISE will hang.

2. From the DISE main window, click Options > Restore Backup to restore an image you created, or click Options > Restore Factory Backup to restore the factory image.

Re-Installing Individual Drivers and Applications

The Drivers and Application CD can be used to selectively re-install drivers and/or applications that may have been un-installed or corrupted.

To re-install drivers and/or applications:

1. Boot up the system and insert the DAR CD after Windows has started. The LifeBook Easy Installation screen appears.

2. Select the drivers and applications you want to install from the list that is displayed.

3. Click [Start]. Follow the prompts that appear to complete installation of the selected drivers and/or applications.

Troubleshooting

LifeBook C Series Notebook – Section Six

Care and Maintenance

LifeBook C Series Notebook – Section Seven

Care and Maintenance

If you use your LifeBook notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the LifeBook notebook and

its devices.

Electrical equipment may be hazardous if misused. Operations of this product or similar products must always be supervised by an adult. Do not allow children access to the interior of any electrical products and do not permit them to handle any cables.

LIFEBOOK NOTEBOOK

Caring for your LifeBook notebook

■

Your LifeBook notebook is a durable but sensitive electronic device. Treat it with respect and care.

■

Make a habit of transporting it in a suitable carrying case.

■

Do not attempt to service the computer yourself. Always follow installation instructions closely.

■

Keep it away from food and beverages.

■

If you accidentally spill liquid on your LifeBook notebook:

1. Turn it off.

2. Position it so that the liquid can run out.

3. Let it dry out for 24 hours, or longer if needed.

4. If your LifeBook notebook will not boot up after it has dried out, call your support representative.

■

Do not use your LifeBook notebook in a wet environment (near a bathtub, swimming pool).

■

Always use the AC adapter and batteries that are approved for your LifeBook notebook.

■

Avoid exposure to sand, dust and other environmental hazards.

■

Do not expose your LifeBook notebook to direct sunlight for long periods of time as temperatures above 140° F (60° C) may damage your notebook.

■

Keep the covers closed on the connectors and slots when they are not in use.

■

Do not put heavy or sharp objects on the computer.

■

If you are carrying your LifeBook notebook in a briefcase, or any other carrying case, make sure that there are no objects in the case pressing on the lid.

■

Never position your LifeBook notebook such that the media player drive is supporting the weight of the notebook.

Care and Maintenance

■

Do not drop your LifeBook notebook.

■

Do not touch the screen with any sharp objects.

Cleaning your Fujitsu notebook

■

Always disconnect the power plug. (Pull the plug, not the cord.)

■

Clean your LifeBook notebook with a damp, lint-free cloth. Do not use abrasives or solvents.

■

Use a soft cloth to remove dust from the screen. Never use glass cleaners.

Storing your Fujitsu notebook

■

If storing your LifeBook notebook for a month or longer, turn your LifeBook notebook off, fully charge the battery, the remove and store all Lithium ion batteries.

■

Store your LifeBook notebook and batteries separately. If you store your LifeBook notebook with a battery installed, the battery will discharge, and battery life will be reduced. In addition, a faulty battery might damage your LifeBook notebook.

■

Store your LifeBook notebook in a cool, dry location. Temperatures should remain between 13ºF (-25ºC) and 140ºF (60ºC).

Traveling with your Fujitsu notebook

■

Do not transport your LifeBook notebook while it is turned on.

■

Do not check your LifeBook notebook as baggage. Carry it with you.

■

Avoid putting your LifeBook notebook through a metal detector. Have your notebook hand-inspected by security personnel. You can however, put your LifeBook notebook through a properly tuned X-ray machine. To avoid problems, place your notebook close to the entrance of the machine and remove it as soon as possible or have your LifeBook notebook handinspected by security personnel. Security officials may require you to turn your LifeBook notebook on. Make sure you have a charged battery on hand.

■

When traveling with the hard drive removed, wrap the drive in a non-conducting materials (cloth or paper). If you have the drive checked by hand, be ready to install the drive if needed. Never put your hard drive through a metal detector. Have your hard drive hand-inspected by security personnel. You can however, put your hard drive through a properly tuned X-ray machine.

■

Take the necessary plug adapters if you're traveling overseas. Check the following diagram to determine which plug adapter you'll need or ask your travel agent.

LifeBook C Series Notebook – Section Seven

Outlet Type Location

United States, Canada, parts of Latin America, Japan, Korea, Mexico, Taiwan, the Philippines

Russia and the Commonwealth of Independent States (CIS), most of Europe, parts of Latin America, the Middle East, parts of Africa, Hong Kong, India, most of South Asia

United Kingdom, Ireland, Malaysia, Singapore, parts of Africa

China, Australia, New Zealand

Figure 7-1. International Outlet Types

BATTERIES

Caring for your Batteries

■

Always handle batteries carefully.

■

Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry loose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire.

■

Do not drop, puncture, disassemble, mutilate or incinerate the battery.

■

Recharge batteries only as described in this manual and only in ventilated areas.

■

Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten battery life.

■

Do not leave a battery in storage for longer than 6 months without recharging it.

Increasing Battery Life

■

Power your LifeBook notebook with the AC or optional auto/airline adapter whenever possible.

■

If your LifeBook notebook is running on battery power all day, connect it to the AC adapter overnight to recharge the battery.

■

Keep brightness to the lowest level comfortable.

■

Set the power management for maximum battery life.

■

Put your LifeBook notebook in Suspend mode when it is turned on and you are not actually using it.

■

Limit your media drive access.

■

Disable the media player auto insert notification function.

■

Always use fully charged batteries.

■

Eject PCMCIA cards when not in use.

FLOPPY DISKS AND DRIVES

Caring for your Floppy Disks

■

Avoid using the floppy disks in damp and dusty locations.

■

Never store a floppy disk near a magnet or magnetic field.

■

Do not use a pencil or an eraser on a disk or disk label.

■

Avoid storing the floppy disks in extremely hot or cold locations, or in locations subject to severe temperature changes. Store at temperatures between 50º F (10ºC) and 125ºF (52ºC).

■

Do not touch the exposed part of the disk behind the metal shutter.

Caring for your Floppy Disk Drive

■

To clean, wipe the floppy disk drive clean with a dry soft cloth, or with a soft cloth dampened with water or a solution of neutral detergent. Never use benzene, paint thinner or other volatile material.

■

Avoid storing the floppy disk drive in extremely hot or cold locations, or in locations subject to severe temperature changes. Store at temperatures between 50º F (10ºC) and 125ºF (52ºC).

■

Keep the floppy disk drive out of direct sunlight and away from heating equipment.

■

Avoid storing the floppy disk drive in locations subject to shock and vibration.

■

Never use the floppy disk drive with any liquid, metal, or other foreign matter inside the floppy disk drive or disk.

■

Never disassemble or dismantle your floppy disk drive.

Care and Maintenance

MEDIA CARE

Caring for your Media (DVD/CD/CD-R/DVD-R/DVD-RW)

Media discs are precision devices and will function reliably if given reasonable care.

■

Always store your media disc in its case when it is not in use.

■

Always handle discs by the edges and avoid touching the surface.

■

Avoid storing any media discs in extreme temperatures.

■

Do not bend media discs or set heavy objects on them.

■

Do not spill liquids on media discs.

■

Do not scratch media discs.

■

Do not put a label on media discs.

■

Do not get dust on media discs.

■

Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen.

■

If a media disc is subjected to a sudden change in temperature, cold to warm condensation may form on the surface. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at room temperature. DO NOT use a hair dryer or heater to dry media discs.

■

If a disc is dirty, use only a DVD/CD cleaner or wipe it with a clean, soft, lint free cloth starting from the inner edge and wiping to the outer edge.

Caring for your Media Player Drive

Your media player drive is durable but you must treat it with care. Please pay attention to the following points:

■

The drive rotates the compact disc at a very high speed. Do not carry it around or subject it to shock or vibration with the power on.

■

Avoid using or storing the drive where it will be exposed to extreme temperatures.

■

Avoid using or storing the drive where it is damp or dusty.

■

Avoid using or storing the drive near magnets or devices that generate strong magnetic fields.

■

Avoid using or storing the drive where it will be subjected to shock or vibration.

■

Do not disassemble or dismantle the media player drive.

PC CARDS

Caring for your PC Cards

PC Cards are durable, but you must treat them with care. The documentation supplied with your PC Card will provide specific information, but you should pay attention to the following points:

■

To keep out dust and dirt, store PC Cards in their protective sleeves when they are not installed in your LifeBook notebook.

■

Avoid prolonged exposure to direct sunlight or excessive heat.

■

Keep the cards dr y.

■

Do not flex or bend the cards, and do not place heavy objects on top of them.

■

Do not force cards into the slot.

■

Avoid dropping cards, or subjecting them to excessive vibration.

LifeBook C Series Notebook – Section Seven

Specifications

LifeBook C Series Notebook – Section Eight

Fujitsu Lifebook C2240 User's Guide

Specifications and Main Features

Frequently Asked Questions

User Manual