24V, 2" HIGH SPEED THERMAL PRINTER
FTP-627 Series
■ OVERVIEW
The FTP-627 MCL Series consists of 24V drive ultra compact
printers with 2 inch paper widths (58mm), which can print at
high speed. Paper can be easily set by an unique platen
NOT FOR NEW
release mechanism.
The FTP-627 MCL series can be used for a variety of
applications, such as portable terminals, POS, ticket issuing
terminals, label printers, and measurement and medical
equipment.
■ HIGHLIGHTS
• Ultra compact
Height 15.5 mm, width 69.6 mm, depth 34.3 mm (MCL002)
• High speed printing
It can print at 60 mm/s (480 dotlines/s) maximum by using
Fujitsu's unique head drive control.
DESIGN
• With Auto Cutter
Two types of compact cutters, a full cut and a partial cut, are
in series.
• High resolution printing / Kanji supported
8 dots/mm of resolution printing is possible.
• Easy paper setting
Our unique platen release mechanism allows a
wide paper route even if the printer is ultra-compact, so
paper can be easily inserted. Auto loading is also available
on MCL001, MCL003 and MCL303 models.
• Two types of paper routes
Front and bottom paper feed.
• Easy mounting
Head, motor, sensor and other component wiring are unified
to one flexible cable, and the mechanism can be secured by
one hook and two screws at two locations, making mounting
easy.
1
■ PART NUMBERS
metIrebmuNtraP
msinahcemretnirP
FTP-627MCL Series
hctiwsnoitcetednepodaehtuohtiwnoitresnirepaptnorf(100LCM726-PTF
hctiwsnoitcetednepodaehtuohtiwnoitresnirepapmottob(200LCM726-PTF
)bonkdnahctiwsnoitcetednepodaehhtiwnoitresnirepaptnorf(300LCM726-PTF
)hctiwsnoitcetednepodaehhtiwnoitresnirepapmottob(400LCM726-PTF
rettuchtiwmsinahceM
gnivirdrofISL101UC726-PTF
ecafretnI
draoB
NOT FOR NEW
ylnoKNA
ijnaK
detroppus
)lairesC232SR(110LSD726-PTF
)scinortneC(110LCD726-PTF
)scinortneC(111LCD726-PTF
rettuctucllufhtiw300LCM10#303LCM726-PTF
rettuctuclaitraphtiw300LCM20#303LCM726-PTF
,)hsalfhtiwlairesC232SR(211LSD726-PTF
■ SPECIFICATIONS
SpecificationsItem
Part number FTP-627MCL001/002/003/004/303#01/303#02
Printing method Thermal-line dot method
Dot structure 384 dots/line
Dot pitch (Horizontal) 0.125 mm (8 dots/mm)—Dot density
Dot pitch (Vertical) 0.125 mm (8 dots/mm)—Line feed pitch
Effective printing area 48 mm
DESIGN
Number of columns ANK 32 columns/line (maximum 12x 24 dot font)
Paper width 58 mm
Paper thickness 60 to 80 µ m (some paper in this range may not be used because of
paper characteristics)
Printing Speed Maximum 60mm/sec. (480 dot line/sec.)
Character types
Character, dimensions (H×W), number of
columns
Alphanumeric, katakana: 159 types
International and special characters: 195 types
JIS Kanji level 1, level 2, non-Kanji
(supported only by FTP-627DSL112, DCL111): about 6800 types
12 × 24 dots, (1.5 × 3.0 mm), 32 columns: alphanumeric, katakana
24 × 24 dots, (3.0 × 3.0 mm), 16 columns: alphanumeric, katakana, Kanji
8 × 16 dots, (1.0 × 2.0 mm), 48 columns: alphanumeric, katakana
16 × 16 dots, (2.0 × 2.0 mm), 24 columns: alphanumeric, katakana, Kanji
+0
-1
2
■ SPECIFICATIONS
metInoitacificepS
ecafretnI scinortneC/C232SRotsmrofnoC
FTP-627MCL Series
daehtnirproF
rewoP
ylppus
cigolroFmumixamA2.0,%5±CDV5
snoisnemiD
NOT FOR NEW
rettuc
thgieW
rettuc
daeH
efiL
rettuCmuminim000,003
DESIGN
retnirpforotomroFmumixamA1,%5±CDV42
rettucforotomroFmumixamA1,%5±CDV42
msinahcemretnirP )dedulcxerevel(300LCM,)HxDxW(mm5.51x7.53x5.38
rettuchtiwmsinahceM )dedulcxeeraselbacdnaswercs(,)HxDxW(mm4.62x0.34x5.38
draobecafretnImm42x98x131
tuohtiwmsinahcemretnirP
htiwmsinahcemretnirP
erutarepmetgnitarepO
g55yletamixorppA
g021yletamixorppA
)sselro%52:oitartnirp(
)C˚04+otC˚0taelbissop
)stod46,NOylsuoenatlumis,V42)0051=vaR
,C˚52(A1.1.xorppatnerruc,tnerrucegareva%5±CDV42
dradnatsruorednu(tod/seslupnoillim001:ecnatsiseresluP
mk05ecnatsidgnilevartrepap:ecnatsisernoisarbA.)snoitidnoc
sinoitarepo,egnarecnarussaytisnedgnitnirp(C˚04+otC˚5+
gnitarepO
tnemnorivne
noitceteD
noitcnuf
ytidimuhgnitarepO)noitasnednocon(HR%58ot02
erutarepmetegarotS)dedulcnitonrepap(C˚06+otC˚02-
ytidimuhegarotS)noitasnednocon(HR%59-5
noitcetederutarepmetdaeHrotsimrehtybdetceteD
noitcetedkram/tuorepaPretpurretni-otohpybdetceteD
noitcetedpudaeH )ylno2#303/1#303/400/300(hctiws-edilsybdetceteD
repapevitisneslamrehtdednemmoceR
:repap
:repapevitisneshgiH)repaPnoppiN(4E-SK05FT
:repapdradnatS)repaPnoppiN(E-SK06F
)mm85(4010P020-PTF,100UP020-PTF
)repaPijO(R051DP
)mm85(1070P020-PTF
egarotsefilmuideM
)mm85(2010P-PTF
)repaPijO(R071DP
:repapegarotsefilgnoL
)repaPnoppiN(1F-SK06FT
)repaPihsibustiM(1-BBV022P
)repaPijO(N-R06DP
)repaPihsibustiM(532-PFA
)repaPnoppiN(R-JK05PT
)repaPihsibustiM(AA022AH
3
FTP-627MCL Series
■ FUNCTION
metImetI
.1noitcnuftnirptseT.8noitcetedytilamronbarettuC
.2noitcetedtuorepaP.9noitcnufgnivasrewoprotoM
.3noitceteddneraenrepaP.01noitcnufnoitcetedkraM
.4noitcetedpudaeH.11noitcetedytilamronbanoitarepoUCM
.5
.6noitcetedesuftuo-wolB.31noitcetorptnerruc-revorotoM
NOT FOR NEW
.7noitcetedytilamronbaegatlovdaeH.41remiterawdraH
■ DIMENSIONS
1. Printer mechanism
noitceted
ytilamronbaerutarepmetdaehlamrehT
.21noitcetorpecneuqesFFO/NOrewoP
DESIGN
Unit: mm
4
2. Interface board
5.1
6.4
55.9
FTP-627MCL Series
130.8
83.8
4 - ø 3.6±0.1
CN11*
88.9
78.7
39.4
CN1
CN10
CN8
CN5**CN2
39.4
NOT FOR NEW
30.5
5.1
* CN11 used
DESIGN
** CN5 used for paper near end detection
91.4
120.7
Part mounting side
Part solder side
5.1
Unit: mm
5
FTP-627MCL Series
■ PRINTER CONNECTOR (CN8) (FLEXIBLE PT BOARD) PIN ARRAYS
Control circuit side connector: 52030-3010 Molex or equivalent product
No. Signal I/O Contents No. Signal I/O Contents
1 PHK — Photo interrupter (cathode) 2 VSEN I
3 PHE O Photo interrupter (emitter) 4VH I
5VH I
7 GND —
9 LAT I Data latch 10 CLK I
11 STB6 I Enable 6 12 STB5 I
NOT FOR NEW
13 STB4 I Enable 4 14 VDD I
15 STB3 I Enable 3 16 STB 2 I
17 STB1 I Enable 1 18 TH O
19 TH O Thermistor 20 GND —
21 GND —
23 VH I
25 SW1 I Head open switch* 26 SW2 O Head open switch*
27 MT/B I Stepping motor coil 28 MT/B I Stepping motor coil
29 MT/A I Stepping motor coil 30 MT/A I Stepping motor coil
DESIGN
Head driving power supply
Ground for head
Ground for head
Head driving power supply
excitation signal B excitation signal B
excitation signal A excitation signal A
6 GNC —
8 DIN I
22 VH I
24 N.C. —
Power supply for paper sensor
Head driving power supply
Ground for head
Data input
Clock
Enable 5
Logic Power supply
Enable 2
Thermistor
Ground for head
Head driving power supply
Open terminal
* on MCL003 / MCL004/ MCL303#01 and MCL303#02 models
6
FTP-627MCL Series
■ INTERFACE
1. Centronics interface
(1) Connector (CN1)
Connector part number : FCN-605Q030-G/S (Fujitsu Components) or equivalent
Mating connector part number : FCN-607B030-G/D (Fujitsu Components) or equivalent
(2) Connector pin assignment
No. Signal I/O Contents No. Signal I/O Contents
1 PRSTB I Data strobe 2 PRSTB-RET —
3 PRDT0 I Data 0 4 PRDT0-RET —
5 PRDT1 I Data 1 6 PRDT1-RET —
NOT FOR NEW
7 PRDT2 I Data 2 8 PRDT2-RET —
9 PRDT3 I Data 3 10 PRDT3-RET —
11 PRDT4 I Data 4 12 PRDT4-RET —
13 PRDT5 I Data 5 14 PRDT5-RET —
15 PRDT6 I Data 6 16 PRDT6-RET —
17 PRDT7 I Data 7 18 PRDT7-RET —
19 ACKNLG O Data input acknowledge 20 ACKNLG-RET —
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
DESIGN
21 BUSY O Busy 22 BUSY-RET —
23 RINF2 O Printer status 2 24 INPRM-RET —
25 SLCTIN I Printer select 26 INPRM I Reset
27 RINF1 O Printer status 1 28 RINF3 O Printer status 3
29 ATF I Paper feed request 30 GND — Logic GND
Connected to logic GND
Connected to logic GND
Notes:
• Symbol “——” means a negative logic signal.
• “–RET” signal is a return signal of the twisted pair cable.
• “I” or “O” means a signal direction from the interface board side.
(3) Connector pin number
FCN-605Q030-G/S(Fujitsu Components)
(4) Data input signal timing
PRDT0~7
PRSTB
BUSY
ACKNLG
t1 t3
t2
t4
Data set time
PRSTB pulse width
Data hold time
PRSTB to BUSY= “H”
ACKNLG pulse time
t5
:t1≥0.5 µsec
:t2≥0.5 µsec
:t3≥0.5 µsec
:t4≤0.5 µsec
:t5≈ 5.0 µsec
7
FTP-627MCL Series
(5) Printer status signals
sutatsrorrE1FNIR2FNIR3FNIR
.1tuorepaPwoLhgiHwoL
.2dneraenrepaPhgiHhgiHwoL
.3pudaeHhgiHwoLwoL
.4ytilamronbaerutarepmetdaeHhgiHwoLhgiH
.5ytilamronbaegatlovdaeHwoLhgiHhgiH
.6ytilamronbaerawdraHhgiHhgiHhgiH
.7ytilamronbanoitcetedkraMwoLwoLwoL
.8lamroNwoLwoLhgiH
NOT FOR NEW
2. RS-232C
(1) Connector (CN2)
Connector part number : B6B-XH-A (J.S.T.) or equivalent
Mating connector part number : XHP-6 (J.S.T.) or equivalent
(2) Connector pin assignment
.oNlangiSO/I.oNstnetnoC.oNlangiSO/I.oNstnetnoC
1GF- dnuorgemarF2DRI atadevieceR
3DTO atadnoissimsnarT4RTDO ydaerlanimretataD
5DNG- dnuorglangiS6RSDI ydaertesataD
7NITCLSI tcelesretnirP8MRPNIIteseR
9FTAI tseuqerdeefrepaP01DWPI
Notes:
• Symbol “——” means a negative logic signal.
• “I” or “O” means a signal direction from the interface board side.
Cutter (CN11)
DESIGN
langis
noitallecnacnwodrewoP
8
FTP-627MCL Series
■ CONNECTOR PIN ASSIGNMENT
1. Connector for power supply (CN10)
Part number : B6B-VH White (J.S.T) or equivalent (board side)
Mating connector part number: VHR-6 (J.S.T.) or equivalent
NOT FOR NEW
2. Connector for printer mechanism connection (CN8)
Part number : 52030-3010 (made by Molex) or equivalent (board side)
No. Signal I/O Contents No. Signal I/O Contents
1 PHK — Photo interrupter (cathode) 2 VSEN O
3 PHE I Photo interrupter (emitter) 4VH O
5VH O
7 GND —
9 LAT O Data latch 10 CLK O
11 STB6 O Enable 6 12 STB5 O
13 STB4 O Enable 4 14 VDD O
15 STB3 O Enable 3 16 STB 2 O
17 STB1 O Enable 1 18 TH I
19 TH I Thermistor 20 GND —
21 GND —
23 VH O
25 SW1 O Head open switch* 26 SW2 I Head open switch*
27 MT/B O Stepping motor coil 28 MT/B O Stepping motor coil
DESIGN
Head driving power supply
Ground for head
Ground for head
Head driving power supply
excitation signal B excitation signal B
6 GNC —
8 DIN O
22 VH O
24 N.C. —
Power supply for paper senor
Head driving power supply
Ground for head
Data input
Clock
Enable 5
Logic Power supply
Enable 2
Thermistor
Ground for head
Head driving power supply
Open terminal
29 MT/A O Stepping motor coil 30 MT/A O Stepping motor coil
excitation signal A excitation signal A
* on MCL003 / MCL004/ MCL303#01 and MCL303#02 models
9
■ OPTIONS
FTP-627MCL Series
emaNrebmuNtraP)mm(htgneL
elbaCecafretnI
dnadraobneewteb(
)tnempiuqe
)01NC(elbacylppusrewoP104Y226-PTF003
)1NC(scinortneCroF102Y226-PTF005
)2NC(C232SRroF103Y226-PTF003
deriuqerfi)5NC(rosnesrepapdneraeN-PTF
NOT FOR NEW
DESIGN
10
FTP-627MCL Series
■ COMMANDS
Command Contents
HT Moves print position to the next tab.
LF Line feed.
FF Feeds forms (new page).
ECS RS Sets reverse printing.
ESC US Resets reverse printing.
ESC ! + n Sets print mode.
ESC %+n Download character set specification//cancellation.
ESC &+y+c1+c2+x+d1~dN Download character definition.
NOT FOR NEW
ESC *+m+n1+n2+d1~dN Sets bit image mode.
ESC ?+n External registration character deletion.
ESC 2 Sets 1/6 inch line feed length.
ESC 3+n Sets the line feed length.
ESC @ Printer initialization.
ESC A+n Sets the space between the line.
ESC C+n Sets the page length by character line.
ESC D+d1~dN+NUL Sets the tab position.
ESC J+n Feeds paper in forward direction and prints.
ESC K+n Reverse paper feed.
ESC R+n Selects international character.
ESC c+1+n Sets internal processing (including auto paper loading).
ESC d+n Printing and n-line feeding.
ESC e+n Prints and reverse feeds n-lines.
ECS s+n Sets printing speed.
ECS t+n Character code table selection.
ESC {+n Sets/resets upside down printing.
DESIGN
FS !+n Kanji printing mode collective specification.
FS & Kanji printing mode specification.
FS . Kanji printing mode cancellation.
FS 9+n Sets the detection functions.
11
FTP-627MCL Series
Commands continued
Command Contents
FS C+n Kanji code system selection.
FS W+n Kanji double height and width mode specification/cancellation.
GS < Line feeds to the next mark.
GS A+m+n Sets the line feed length after mark detection.
GS E+n Sets print quality.
GS V+n+m Paper cutting.
GS e+n+m Sets bar code width.
GS h+n Sets bar code height.
NOT FOR NEW
GS k+m+n+d1~dN Selects bar code type and prints.
GS w+n Sets bar code width magnification.
FS *+m+n1+n2+d1~dN High speed collective image printing specified.
GS &+m+x+y1+y2+d1~dN Registration of image data.
GS '+m+n Prints registered image data.
FS E+n Correction of impressed energy.
ESC V+n Right Rotation 90° specification / cancellation.
GS a+n Sets and cancels status transmission. (Serial Mode)
FS r+n Parameter transmission. (Serial Mode)
ESC EM+n Setting the amount of the feeding at automatic paper load.
ESC X+n+m Setting the turning time of the motor excitation.
ESC DEL+n Deletes recorded contents in flash memory.
Fujitsu Components
International
Headquarter
Offices
DESIGN
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: promothq@ft.ed.fujitsu.com
Web: www.fcl.fujitsu.com
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: marcom@fcai.fujitsu.com
Web: www.fcai.fujitsu.com
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: info@fceu.fujitsu.com
Web: www.fceu.fujitsu.com
Asia Pacific
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (65) 6273-3021
Email: fcal@fcal.fujitsu.com
www.fcal.fujitsu.com
© 2003 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 04/03/2003
12
Loading...