Fujitsu FTP-622DSL001-011-012, FTP-622DCL001-011 User Manual

24V DRIVE INTERFACE BOARD (PARALLEL) FTP-622DCL001/011/ FTP-622DSL001/011/012

FOR FTP-622/632/642MCL001/002/301/302/303/304

■ INTERFACE

1. Centronics

(1) Connector (CN1)

Connector part number : FCN-605Q030-G/S (Fujitsu Components) Mating connector part number : FCN-607B030-G/D (Fujitsu Components) or equivalent

(2) Connector pin assignment

No. Signal I/O Contents No. Signal I/O Contents

1 PRSTB I Data strobe 2 PRSTB-RET — 3 PRDT0 I Data 0 4 PRDT0-RET — 5 PRDT1 I Data 1 6 PRDT1-RET — 7 PRDT2 I Data 2 8 PRDT2-RET —

9 PRDT3 I Data 3 10 PRDT3-RET — 11 PRDT4 I Data 4 12 PRDT4-RET — 13 PRDT5 I Data 5 14 PRDT5-RET — 15 PRDT6 I Data 6 16 PRDT6-RET — 17 PRDT7 I Data 7 18 PRDT7-RET — 19 ACKNLG O Data input acknowledge 20 ACKNLG-RET — 21 BUSY O Busy 22 BUSY-RET — 23 RINF2 O Printer status 24 INPRM-RET — 25 SLCTIN I Printer select 26 INPRM I Reset 27 RINF1 O Printer status 28 RINF3 O Printer status 29 ATF I Paper feed request 30 GND — Logic GND

Notes:

• Symbol “——” means a negative logic signal.

• “–RET” signal is a return signal of the twisted pair cable.

• “I” or “O” means a signal direction from the interface board side.

(3) Connector pin number

FCN-605Q030-G/S (Fujitsu Components) or

equivalent

No.1

(4) Data input signal timing

PRDT0~7

t1 t3

PRSTB

BUSY

Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND Connected to logic GND

No.30

No.2

ACKNLG

Data set time PRSTB pulse Data hold time

:t1≥0.5 µsec :t2≥0.5 µsec :t3≥0.5 µsec

PRSTB to BUSY= “H”

ACKNLG pulse

:t4≤0.5 µsec

:t5=5.0 µsec

FTP-622DCL/DSL

tcudorPrebmuNtraPnoitcnuF

draoBecafretnIlellaraP

100LCD226-PTF)rettuctuohtiw(dradnatS 110LCD226-PTFlortnocrettuchtiW 100LSD226-PTF)rettuctuohtiw(dradnatS 110LSD226-PTFrellortnocrettuchtiW

draoBecafretnIlaireS

210LSD226-PTFMORHSALF+rellortnocrettuchtiW 211LSD226-PTFMORHSALF+IJNAK+rettuChtiW

■ SPECIFICATION

Item Specification Data receive speed 19200, 9600, 4800, 1200 bps (set by dip switch) Synchronous method Asynchronous, full duplex Hand shake DTR/DSR signal or XON/XOFF Input output level RS232C

Signal level

2. SERIAL INTERFACE (RS232C)

(1) Connector (CN2)

Part number : B6B-XH-A (J.S.T) Mating connector part number : XHP-6 (J.S.T) or equivalent

(2) Pin assignment

Space (logic = 0) +3 V ~ +12 V Mark (logic = 0) –3 V ~ –12 V

No. Signal I/O Contents No. Signal I/O Contents

1 FG — Frame GND 2 RD I Receive data 3 TD O Transmission Data 4 DTR O Data terminal ready 5 GND — Signal GND 6 DSR I Data set ready

Notes: “I” or “O” means a signal direction from the interface board side.

(3) Pin number

B6B-XH-A (J.S.T)

CN1

CN2

FTP-622DCL/DSL

■ CONNECTOR PIN ASSIGNMENT

1. Connector for power supply (CN10)

Part number : B6P-VH (J.S.T) Mating connector part number : VHR-6N (J.S.T) or equivalent

No. Signal I/O Contents No. Signal I/O Contents

1VCC — Power supply for logic (+5 V) 2 GND — GND (5 V, 24 V common) 3 GND — GND (5 V, 24 V common) 4 GND — GND (5 V, 24 V common) 5VDD — Power for head/motor (+24 V) 6 V DD — Power for head/motor (+24 V)

2. Connector for thermal head drive (CN8)

Part number : B16B-PH-K-S (J.S.T) Mating connector part number : PHR-16 (J.S.T) or equivalent

No. Signal I/O Contents No. Signal I/O Contents

1 VDH O Power for head (+24 V) 2 VDH O Power for head (+24 V) 3

GND (VDH) 5 STB1 O Print enable signal 1 6 STB2 O Print enable signal 2 7 STB3 O Print enable signal 3 8 TMP I Temperature detection signal 9 STB4 O Print enable signal 4 10 LAT O Print data latch signal

11 STB5 O Print enable signal 5 12 5 VH O Power for logic (+5 V) 13 HCLK O Data transmission clock 14 HD O Print data output signal 15

GND (VDH)

— Head GND 4

— Head GND 16 VDH O Power for head (+24 V)

GND (VDH)

— Head GND

Notes:

• Symbol “——” means a negative logic signal.

• “I” or “O” means a signal direction from the interface board side.

3. Connector for Sensor (CN3)

Part number : B5B-PH-K-S (J.S.T)

No. Signal I/O Contents No. Signal I/O Contents

1 +5 V — Power for logic (+5 V) 2 PES I Paper end detect signal 3

GND (5 V) 5 HUP I Head-up detect signal

— Logic GND 4 +5 V — Power for logic (+5 V)

+ 5 hidden pages