Fujitsu Computer Systems
Bump Case
Installation Guide
FPCCC51
INSTRUCTIONS
These instructions provide details on using the FPCCC51
bump case. This case is designed for use with your Stylistic®
CT2000 Series CE Tablet. The bump case provides added
protection when transporting, using, or storing the tablet.
Prior to installing your tablet in the bump case,
be sure to do the following:
• Install a screen protector on the screen. It is
difficult to install a screen protector once the
system is in the bump case.
• If you intend to use the system in the case,
remove the pen from the system holder and
insert it in the pen holder on the top front of
the case.
• Remove the covers from any of the ports
you intend to use.
Description
There are three flaps on the bump case. When the case is
held as shown in Figure 2, the flaps are on the left, right, and
bottom.
The left flap has a slot in it to allow access to the USB jack,
audio jack, and Compact Flash slot. The right flap can be
opened to remove and install a battery pack. Two openings
on the back of the case provide access to the battery release
latches. The top edge of the case has slots in it to allow access
to the PC Card slot and serial port.
D-RIngs (four places)
Handstraps
Velcro Strips (behind flaps)
Top
Bottom
Figure 1. Pen Tablet PC Bump Case - Rear
2
Installation
PWR
CLR
BKS
F1
F2
F3
F4
To install your tablet into the bump case, open the bottom
flap and either one of the side flaps. The flaps are secured by
Velcro® strips (see Figure 1).
Slide the pen tablet into the case, with the display screen
facing the open window (see Figure 2). Reattach the flap(s)
on the bump case.
Hand straps
The bump case has two elasticized hand straps on the back
(see Figure 1). Insert your hand between the straps and the
case in whichever orientation is most comfortable for you.
Pen Holder
Figure 2. Pen Tablet PC Bump Case - Front
1
2
3
4
5
6
CLR
CLR
BKS
BS
F1
F1
F3
F3 F4
PWR
0
ENT
7
8
9
F2
F2
F4
3
Pen holder
When you have the tablet installed in the case, store the
tablet pen in the pen holder (Figure 2) to simplify access to it
when using the system.
Shoulder strap
To secure the shoulder strap, attach the strap clips to two of
the D-rings. The bump case can be carried vertically or horizontally, depending on how you attach the clips.
Caring for the bump case
The bump case is made of rugged materials, and is designed
to withstand daily use. Treat the case as you would a briefcase or purse. Occasionally, the bump case may become
soiled. To clean it, use a clean cloth and warm soapy water to
wash the soiled area.
4
5
6
7
Fujitsu Computer Systems Corporation
1250 E. Arques Avenue (M/S 122),
Sunnyvale, California 94085
For more information, call
1-877-372-3473 or visit our Web site at:
us.fujitsu.com/computers
For technical support call: 1-800-8Fujitsu (1-800-838-5487)
or e-mail us at: 8fujitsu@us.fujitsu.com
Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu, Ltd.
Microsoft and Windows are registered trademarks of the Microsoft
Corporation. All other trademarks mentioned herein are the property of their
respective owners. We cannot guarantee the accuracy of the contents of this
document. We disclaim liability for errors, omissions or future changes.
© 2004 Fujitsu Computer Systems Corporation. All rights reserved.
FPC58-1116-01
8
Loading...