
58_0497_02.fm Page 1 Tuesday, July 10, 2001 2:18 PM
Fujitsu PC Corporation
Radio Antenna Cover Kit
Installation Guide
FMW42RC1 and FMW42RC2
For use with StylisticTM 3400 and 3500 Pen Tablet PCs
INSTRUCTIONS
These instructions provide details on assembling and
installing the radio antenna cover kit for the Stylistic Pen
Tablet PC.
The antenna cover should be installed when most types of
antenna protrude from a radio PC Card. The cover provides
a rigid cap over the antenna to prevent damage during
everyday use.
POINT
The FMW42RC1 antenna cover was tested with specific
models of Symbol
TM
AiroNet
other brands of radio may protrude too far from the system
to fit within this model of antenna cover. In those cases, the
FMW42RC2 antenna cover should be used.
®
, ProximTM, BreezeComTM, and
radios. The antennas on certain models and

58_0497_02.fm Page 2 Tuesday, July 10, 2001 2:18 PM
ASSEMBLING THE ANTENNA COVER KIT
Note : This section is applicable only to antenna cover model
FMW42RC1 only; the FMW42CR2 model is pre-assembled.
The radio antenna cover kit consists of the following parts:
■
Plastic Hood
■
Plastic Base
■
Two screws (M2.5 x 8 mm long, finish:black zinc)
■
One tapping screw (Model FMW42RC1 only)
To assemble the radio antenna cover, place the hood atop the
base as illustrated in Figure 1. Make sure the positioning tab
is on the inside of the hood. Secure the two pieces with the
tapping screw by inserting it through the hole in the base
into the standoff inside the hood.
Hood
Standoff
Positioning
Tab (inside)
Base
Figure 1. Assembling the Radio Antenna Cover
2
Tapping Screw

58_0497_02.fm Page 3 Tuesday, July 10, 2001 2:18 PM
INSTALLING THE RADIO ANTENNA COVER
To attach the radio antenna cover to the pen tablet PC,
perform the following steps.
1. Position the antenna cover in relation to the back of the
pen tablet PC as shown in Figure 2.
2. If caps are present over the mounting holes, remove
them with a small screwdriver, or similar tool.
3. If the FMW42CR2 antenna cover is being used, slide the
open slot in the cover (as outlined in Figure 2) over the
antenna so that the antenna protrudes from the cover.
4. Insert the antenna cover tabs into the two tab slots on
the pen tablet.
Note: If the screws referenced in the step below are either lost or
missing, they can be purchased at most hardware stores (Cross-recessed
head Machine Screw with spring washer and flat washer. Size: M2.5 x
8 mm long. Finish:Black Zinc)
5. Insert the two black screws through the holes in the
hood and secure them to the pen tablet.
Tab Slots
Antenna Slot
(FMW42RC2
model only)
Figure 2. Installing the Radio Antenna Cover
Tab
Mounting
Hole
PC Card Slot
3

58_0497_02.fm Page 4 Tuesday, July 10, 2001 2:18 PM
5200 Patrick Henry Drive
Santa Clara, CA 95054
For more information, visit our Web site
at: www.fujitsupc.com
For technical support call:
1-800-8Fujitsu (1-800-838-5487)
or e-mail us at: 8fujitsu@fujitsupc.com
Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu, Ltd. Stylistic is a
trademark of Fuji tsu PC Corporation. All other t rademarks mentioned herein are th e
property of their respective owners. We cannot guarantee the accuracy of the contents of
this document. We disclaim liability for errors, omissions or future changes.
© 2001 Fujitsu PC Corporation. All rights reserved. FPC58-0497-02
4