MINIATURE RELAY
2 POLES—1 to 2 A (FOR SIGNAL SWITCHING)
FBR12 SERIES
■ FEATURES
● Super miniature size: 0.2 inch × 0.1 inch grid, 12 pin DIP
Up to 50% less volume and board area than previous
generation telecom relay.
● Slim type for high density mounting
● Conforms to Bellcore TR-NWT-001089 and FCC Part 68
requirements
● UL recognized and CSA certified
● Low power consumption
● Conforms to IEC 950 (W type only)
– 2.5 mm clearance and creepage between coil and contacts
–5000 V surge strength between coil and contacts (2x10µs
surge wave)
–2000 Vrms dielectric strength between coil and contacts
–UL 1950 and IEC950 (approval in process)
FBR12 SERIES TO
NOT FOR NEW
DESIGN
■ ORDERING INFORMATION
[Example]
BE DISCONTINIED
(a) Series Name FBR12 : FBR12 Series
(b) Enclosure & Coil Power
(c) Coil Type D : DC coil
(d) Nominal Voltage Refer to the COIL DATA CHART
(e) Contact Material
(f) Custom Designation To be assigned custom specification
(g) CSA Standard
Note: The designation name is stamped on the top of the relay case as follows:
(Example) Designation ordered: FBR12ND05
■ SAFETY STANDARD AND FILE NUMBERS
UL508, 1950, 114 (File No. E63615)
C22.2 No. 0, No. 14 (File No. LR40304 or LR64026)
Nominal coil voltage Contact rating
3 to 24 VDC 2 A 30 VDC resistive
FBR12 N D 12 –P
(a) (b) (c) (d) (e) (f) (g)
Stamp: 12ND05
0.5 A 125 VDC resistive
0.3 A 110 VAC resistive
–** (–CSA)
N : Standard (plastic sealed type)
W : High dielectric strength type (plastic sealed type)
H : High sensitivity type
Nil : Gold-overlay silver-nickel
–P : Gold-overlay silver-palladium
–CSA : UL114 + CSA recognized
–CSA : UL1950 + CSA (under application)
1
FBR12 SERIES
■ SPECIFICATIONS
Item
Contact Arrangement 2 form C (DPDT)
Material Gold-overlay silver-nickel Gold-overlay silver-palladium
Style Bifurcated
Resistance (initial) Maximum 100 mΩ (at 0.1 A 6 VDC)
Rating (resistive) 0.5 A 125 VAC or 1 A 30 VDC
Maximum Carrying Current 2 A (at 20°C)
Maximum Switching Power 62.5 VA or 60 W
Max. Switching Voltage*
Maximum Switching Current 2 A
Minimum Switching Load*
Capacitance Approximately 1.0 pF (between open contacts, adjacent contacts )
FBR12 SERIES TO
(at 10 kHz) Approximately1.0 pF (between coil and contacts)
Coil Nominal power (at 20°C) Approximately Approximately Approximately Approximately
Operate power (at 20°C) Approximately Approximately Approximately Approximately
NOT FOR NEW
BE DISCONTINIED
Thermal Resistance at
Continuous Thermal Load
Operating Temperature –40°C to +85°C (no frost) (refer to the CHARACTERISTIC DATA)
Operating Humidity 45 to 85%RH
Time Value Operate (at nominal voltage) Maximum 4 msec.
Release (at nominal voltage) Maximum 4 msec.
Max. Switching Frequency Mechanical 3 Hz or electrical 0.5 Hz (at contact rating)
Insulation Resistance (initial) Minimum 1000 MΩ (at 500 VDC)
Dielectric
Strength
Surge
Strength
Life Mechanical 1 × 108 operations minimum
Electrical DC 2 × 105 operations minimum 5 × 105 operations minimum
(at contact rating)
Other Vibration Misoperation 10 to 55 Hz (double amplitude of 3.3 mm)
Resistance
Shock Misoperation 500 m/s2 (11±1 ms)
Resistance
Weight Approx. 1.5 g Approx. 1.9 g Approx. 1.5 g Approx. 1.9 g
1
*
If the switching voltage exceeds the rated contact voltage, reduce the current. The current values vary according to the
type of load.
2
Values when switching a resistive load at normal room temperature and humidity and in a clean environment.
*
The minimum switching load varies with the switching frequency and operation environment.
between open contacts
adjacent contacts
between coil and contacts
between open
contacts,
adjacent contacts
between coil and contacts
AC 1 × 10
Endurance 10 to 55 Hz (double amplitude of 5.0 mm)
Endurance 1,000 m/s
Standard (Gold-overlay silver-nickel)
Standard
1
250 VAC or 220 VDC
2
10 µA 10 VDC (reference)
High dielectric
strength type strength type
-P type (Gold-overlay silver-palladium)
Standard
DESIGN
0.14 to 0.2 W 0.23 to 0.25 W 0.14 to 0.2 W 0.23 to 0.25 W
0.08 to 0.112 W 0.13 to 0.14 W 0.08 to 0.112 W 0.13 to 0.14 W
Approximately 115°C/W
1,000 VAC
1 minimum
1,500 VAC 1 min. 2,000 VAC 1 min. 1,500 VAC 1 min. 2,000 VAC 1 min.
1,500 V
10 × 700 µs
2,500 V 5,000 V 2,500 V 5,000 V
2 × 10 µs 2 × 10 µs 2 × 10 µs 2 × 10 µs
5
operations minimum 200 × 103 operations minimum
2
( 6 ±1 ms)
1,500
750
2,500
1,250
10
210
700
High dielectric
2
FBR12 SERIES
■ SPECIFICATIONS
Item
Standard (Gold-overlay silver-nickel)
Contact Arrangement 2 form C (DPDT)
Material Gold-overlay silver-nickel Gold-overlay silver-palladium
Style Bifurcated
Resistance (initial) Maximum 100 mΩ (at 0.1 A 6 VDC)
Rating (resistive) 0.3 A 125 VAC or 1 A 30 VDC
Maximum Carrying Current 2 A (at 20°C)
Maximum Switching Power 62.5 VA or 30 W
Max. Switching Voltage*
Maximum Switching Current 2 A
FBR12 SERIES TO
Minimum Switching Load*
Capacitance Approximately 1.0 pF (between open contacts, adjacent contacts )
(at 10 kHz) Approximately1.0 pF (between coil and contacts)
Coil Nominal power (at 20°C) Approximately 50mW
BE DISCONTINIED
Time Value Operate (at nominal voltage) Maximum 5 msec.
Insulation Resistance (initial) Minimum 1000 MΩ (at 500 VDC)
Life Mechanical 1 x 10
Other Vibration Misoperation 10 to 55 Hz (double amplitude of 3.3` mm)
Operate power (at 20°C) Approximately 40m W
Operating Temperature –40°C to +70°C (no frost) (refer to the CHARACTERISTIC DATA)
Operating Humidity 45 to 85%RH
Release (at nominal voltage) Maximum 5 msec.
Dielectric
Strength
Surge
Strength
Electrical DC 2 × 105 operations minimum 5 × 105 operations minimum
(at contact rating)
Resistance
Shock Misoperation 500 m/s2 (11±1 ms)
Resistance
Weight Approx. 1.9 g
between open contacts
adjacent contacts
between coil and contacts
between open
contacts,
adjacent contacts
between coil and contacts
AC 1 × 10
Endurance 10 to 55 Hz (double amplitude of 5.0 mm)
Endurance 1,000 m/s
NOT FOR NEW
1
250 VAC or 220 VDC
2
DESIGN
10m VDC - 10µ A
750 VAC
1 minute
1,500 VAC 1 minutes
1,500 V
10 × 700 µs
2,500 V
2 × 10 µs
High Sensitive Type
-P type (Gold-overlay silver-palladium)
8
operations minimum
5
operations minimum 200 × 103 operations minimum
2
( 6 ±1 ms)
*1 If the switching voltage exceeds the rated contact voltage, reduce the current. The current values vary according to the
type of load.
2
Values when switching a resistive load at normal room temperature and humidity and in a clean environment.
*
The minimum switching load varies with the switching frequency and operation environment.
3
FBR12 SERIES
■ COIL DATA CHART
1.STANDARD
MODEL
Standard -P type
FBR12ND03 FBR12ND03-P 3 VDC 64.3 Ω 46 mA
FBR12ND04 FBR12ND04-P 4.5 VDC 145 Ω 31 mA
FBR12ND05 FBR12ND05-P 5 VDC 178 Ω 28 mA 75% max. 10% min.
FBR12ND06 FBR12ND06-P 6 VDC 257 Ω 23 mA
FBR12ND09 FBR12ND09-P 9 VDC 579 Ω 15 mA
FBR12ND12 FBR12ND12-P 12 VDC 1,028 Ω 11 mA
FBR12ND24 FBR12ND24-P 24 VDC 2,880 Ω 8 mA 0.2 W 0.112 W 30 deg
*1: Specified values are subject to pulse wave voltage.
Note: All values in the table are measured at 20°C.
2.HIGH DIELECTRIC STRENGTH
FBR12 SERIES TO
MODEL
BE DISCONTINIED
Standard -P type
FBR12WD03 FBR12WD03-P 3 VDC 39 Ω 77 mA
FBR12WD04 FBR12WD04-P 4.5 VDC 88 Ω 51 mA
FBR12WD05 FBR12WD05-P 5 VDC 108 Ω 46 mA 75% max. 10% min.
FBR12WD06 FBR12WD06-P 6 VDC 156 Ω 38 mA
FBR12WD09 FBR12WD09-P 9 VDC 352 Ω 25 mA
FBR12WD12 FBR12WD12-P 12 VDC 626 Ω 19 mA
FBR12WD24 FBR12WD24-P 24 VDC 2,304 Ω 10 mA 0.25 W 0.14 W 33 deg
*1: Specified values are subject to pulse wave voltage.
Note: All values in the table are measured at 20°C.
Nominal
voltage
NOT FOR NEW
Nominal
voltage
Coil current Must Must
resistance (at nominal operate operate
(
±
10%) voltage) voltage*1voltage*
DESIGN
Coil current Must Must
resistance (at nominal operate release
±
10%) voltage) voltage*1voltage*
(
Nominal
approx.
Nominal
approx.
1
of nominal of nominal
voltage voltage
1
of nominal of nominal
voltage voltage
Nominal
power
Approx. Approx. Approx.
0.14 W
(at nominal Max.
voltage) Max. (at nominal
Nominal
power
Approx. Approx. Approx.
0.23 W
(at nominal (at nominal
voltage) Max. voltage)
Operate
power
0.08 W
Operate
power
0.13 W
temperature
20 deg
voltage)
temperature
30 deg
Coil
rise
Coil
rise
3. HIGH SENSITIVITY TYPE
MODEL
Standard -P type
FBR12HD03 FBR12HD03-P 3 VDC 180 Ω
FBR12HD04 FBR12HD04-P 4.5 VDC 405 Ω
FBR12HD05 FBR12HD05-P 5 VDC 500 Ω 80% max. 10% min.
FBR12HD06 FBR12HD06-P 6 VDC 720 Ω
FBR12HD09 FBR12HD09-P 9 VDC 1,620 Ω
FBR12HD12 FBR12HD12-P 12 VDC 2,880 Ω
*1: Specified values are subject to pulse wave voltage.
Note: All values in the table are measured at 20°C.
Nominal
voltage
Coil Must Must
resistance operate release
(
±
10%) voltage*1voltage*
of nominal of nominal
voltage voltage
Nominal
1
power
Approx. Approx. Approx.
0.05 W
(at nominal (at nominal
voltage) Max. voltage)
Operate
power
0.04 W
temperature
4 deg
Coil
rise
4
FBR12 SERIES
■ CHARACTERISTIC DATA
Range of operation temperature and voltage
Maximum allowable coil voltage
(DATA) assumes that
160
150
140
130
120
110
100
90
80
Nominal voltage multiplying factor (%)
70
Operating voltage range
Must operate voltage
–100 1020304050607080
Operating temperature (˚C)
the maximum allow able temperature of
E type insulation
coil is 115˚C
NOT FOR NEW
Maximum switching capacity
2.0
1.0
0.5
0.3
0.2
Contact load current (A)
0.1
10 20 125 200
➁
30 50
Contact load voltage (V)
➀ AC resistive load
( AC contact rating)
➁ DC resistive load
( DC contact rating)
➀
4
)
(×10
500
100
50
10
5
Service life (operations)
1
■ REFERENCE DATA
Distribution of operate and release voltage
FBR12 SERIES TO
60
50
40
BE DISCONTINIED
30
Distribution (%)
20
10
Operate
Release
Distribution of operate and release time
DESIGN
100
Operate
80
60
40
Distribution (%)
20
Release
Distribution of contact resistance
80
60
40
Distribution (%)
20
Life curve
30 V DC resistive load
125 V AC
resistive load
(–P)TYPE
0.5 1.0 1.5 2.0
Contact load current (A)
(–P)TYPE
0
01020304050607080
Rated coil voltage multiplying factor (%)
0
012 345 678
Time (ms)
■ DIMENSIONS
●Dimensions ●Schematics
(BOTTOM VIEW)
14.6
+0.3
9.7
(0.95)
3.2
●Tube carrier
10.6 Max.
15.6 Max.
30 pcs/Tube
0.50
+0.4
0.25
(1.06) 5.08
7.2
+0.3
✽SHOW ONE OUT
OF THBSB 3 DIMENSIONS (See NA)
±2
500
112310495
0
01020304050607080
Contact resistance (mΩ)
●PC board mounting hole layout
(BOTTOM VIEW)
5.08
8
5.08
2.54
2.54
8–ø1.00
Unit: mm
5
FBR12 SERIES
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Fujitsu Components
International
Headquarter
Offices
© 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered trademarks
of their respective owners. Rev. 07/26/2004.
FBR12 SERIES TO
T okyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: promothq@ft.ed.fujitsu.com
Web: www.fcl.fujitsu.com
North and South America
Fujitsu Components America, Inc.
NOT FOR NEW
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: marcom@fcai.fujitsu.com
Web: www.fcai.fujitsu.com
DESIGN
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: info.marketing@fceu.fujitsu.com
Web: www.fceu.fujitsu.com
Asia Pacific
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 375-8560
Fax: (65) 273-3021
Email: fcal@fcal.fujitsu.com
www.fcal.fujitsu.com
BE DISCONTINIED
6
Loading...