Fujitsu ETERNUS DX60 S2 User Manual

Download

Page 1

P3AM-5542-07EN

* P 3 A M - 5 5 4 2 - 0 7 E N *

FUJITSU Storage ETERNUS DX60 S2 Disk storage system

Read Me First

Fujitsu would like to thank you for purchasing our ETERNUS DX60 S2 Disk storage system (hereinafter referred to as

"ETERNUS DX Disk storage system").

Read this document and check the shipment package to conrm that no items are missing.

Check the workow to set up the ETERNUS DX Disk storage system by referring to "Setup Procedures". For details on

the procedures, refer to the manuals that are described with the Refer to the provided manuals or any related manuals for the ETERNUS DX Disk storage system as necessary.

mark.

Read and understand the "Safety Precautions" before use.

"Safety Precautions"

The information in this document is subject to change without notice for improvement and functionality expansion of the

ETERNUS DX Disk storage system.

The latest version of this document, the latest information about the ETERNUS DX Disk storage system, and important

service and support contacts (see “Contact Fujitsu”) for Fujitsu Customer Service for your country of purchase is available

at the following website:

http://www.fujitsu.com/global/services/computing/storage/eternus/products/diskstorage/dx-entry/

Table of Contents

Provided Manuals .......................................2

Related Materials .........................................2

Package Contents .......................................3

Setup Procedures .......................................6

Operation and Maintenance .....................13

The company names and product names mentioned in this document are either registered trademarks or trademarks of their respective companies.

Page 2

Provided Manuals

The Documentation CD that is provided with the ETERNUS DX Disk storage system includes the following manuals:

Manual Title Manual Code Description

Overview P3AM-5482 Describes the specications, features, and functions of the

ETERNUS DX Disk storage system.

User's Guide -Site Planning- P3AM-5492 Describes the onsite requirements for installation of the

ETERNUS DX Disk storage system.

User's Guide -Installation- P3AM-5502 Describes all the procedures that are required to start operation

of the ETERNUS DX Disk storage system.

User's Guide -Operation- P3A M- 5 512 Describes the operation management and maintenance of the

ETERNUS DX Disk storage system.

Product List P3AM-5522 Provides lists of the optional products for the ETERNUS DX Disk

storage system and describes possible combinations.

Read Me First P3AM-5542 Describes how the manuals are organized, package contents,

setup procedures, and the terms of use for the ETERNUS DX Disk storage system. A manual booklet is also provided.

Read Me First for Optional Products P3AM-5552

P3AM-5562

Safety Precautions P3AM-5062 Describes the safety precautions that must be taken for the

ETERNUS Web GUI User's Guide P2 X0 -1120 Explains how to monitor and set the ETERNUS DX Disk storage

ETERNUS CLI User's Guide P2 X0 -113 0 Explains how to monitor and set the ETERNUS DX Disk storage

ETERNUS SMI-S User's Guide P3AM-5652 Explains how to use the SMI-S compliant general storage

Describes the package contents of the optional products. Manual

booklets are also provided for optional products.

ETERNUS DX Disk storage system. A manual booklet is also

provided.

system via Graphical User Interface (GUI).

system via Command Line Interface (CLI).

management application to manage the ETERNUS DX Disk storage system.

Related Materials

Other manuals for the ETERNUS DX Disk storage system are as follows:

Manual Title Manual Code Description

Conguration Guide

-Server Connection-

Conguration Guide (Power Synchronized Unit)

(*1)

P3AM- 8012 Explains how to use a power synchronized unit.

Explains how to connect the ETERNUS DX Disk storage system to a server.

*1: Download the necessary manuals for the customer operating environment (for server OS, host interface type, etc.) from the specied website.

For the URL of the download website, refer to the Documentation CD provided with the ETERNUS DX Disk storage system.

FUJITSU Storage ETERNUS DX60 S2 Disk storage system Read Me First

P3AM-5542-07EN

Page 3

Package Contents

Check the list of package contents for the purchased product to conrm that no items are missing. Tick off the checkbox of each conrmed item. If there is a missing item, contact your sales representative.

●

Store the package contents in a safe and secure location, as they may be needed again when making changes to the system or reinstalling the software.

●

Note that the package may sometimes also contain an Errata sheet and/or other such unlisted documentation.

(*1)

ETERNUS DX60 S2 (2.5inch) (Product ID: ET062aC

ETERNUS DX60 S2 (3.5inch) (Product ID: ET062aD

b c

(*1)

)

□Controller enclosure (x 1)

Drives that are purchased at the same time as the ETERNUS DX Disk storage system are preinstalled according to the installation rules.

●2.5inch

●3.5inch

□Cover (x 1)

●2.5inch

Flange cover

●3.5inch

Front cover

□Rack rail kit

□Rack rail (x 1 set)

□AC200V cable (x 2) IEC60320-C13↔NEMA L6-15P (4m)

□Pin (x 1)

Used to adjust the Controller Enclosure's AUTO POWER

dip-switch.

□Network Settings label (x 1)

□Read Me First (this document) (x 1)

□Safety Precautions (x 1)

□Documentation CD (x 1)

□M5 screw (x 8)

for attaching the rack rails

*1: An alphanumerical character is used for

D : dual-controller type S : single-controller type

An alphanumerical character is used for

F : FC

L : iSCSI S : SAS

An alphanumerical character may also be used for

□Screw holder (x 8)

Used when the rack pillars have square holes.

to indicate the ETERNUS DX Disk storage system model.

to indicate the host interface type.

FUJITSU Storage ETERNUS DX60 S2 Disk storage system Read Me First

depending on the purchased product.

P3AM-5542-07EN

Page 4

Drive Enclosure (Product ID: ETEEDaDU, ETCEDaDU

(*1)

)

□Drive enclosure (x 1)

Drives that are purchased at the same time as the ETERNUS DX Disk storage system are preinstalled according to the installation rules.

□Front cover (x 1)

□Rack rail kit

□Rack rail (x 1 set)

□M5 screw (x 8)

for attaching the rack rails

□Screw holder (x 8)

Used when the rack pillars have square holes.

□AC200V cable (x 2) IEC60320-C13↔NEMA L6-15P (4m)

□miniSAS cable SFF8088↔SFF8088 (0.75m)

One miniSAS cable is provided when miniSAS cables are provided when

for the product ID is "1". Two

for the product ID is "2".

*1: An alphanumerical character is used for

1 : One expander 2 : Two expanders

to indicate the number of expanders.

FUJITSU Storage ETERNUS DX60 S2 Disk storage system Read Me First

P3AM-5542-07EN

Page 5

SAS Disk Drive (Product ID: ETED

□Disk Drive

Installed in the controller enclosure or the drive enclosure.

●2.5inch

●3.5inch

a b c

, ETCD

a b c

(*1)

)

*1: An alphanumerical character is used for

3 : 300GB 4 : 450GB 6 : 600GB 9 : 900GB 1 : 1.2TB

An alphanumerical character is used for

H : x1

: x2 (RAID1) P : x6 (R AID5) D : x6 (RAID6) S : x6 (R AID1+0)

An alphanumerical character is used for

A : Disk Drive (3.5inch) 15krpm B : Disk Drive (2.5inch) 10krpm

to indicate the drive capacity.

to indicate the number of drives and the RAID type.

to indicate the drive size and the drive speed.

Nearline SAS Disk Drive (Product ID: ETEN

□Disk Drive

Installed in the controller enclosure or the drive enclosure.

●2.5inch

●3.5inch

a b c

, ETCN

a b c

(*1)

)

*1: An alphanumerical character is used for

1 : 1TB 2 : 2TB 3 : 3TB 4 : 4TB

An alphanumerical character is used for

H : x1

: x2 (RAID1) P : x6 (R AID5) D : x6 (RAID6) S : x6 (R AID1+0)

An alphanumerical character is used for

A : 3.5inch B : 2.5inch

FUJITSU Storage ETERNUS DX60 S2 Disk storage system Read Me First

to indicate the drive capacity.

to indicate the number of drives and the RAID type.

to indicate the drive size.

P3AM-5542-07EN

Page 6

Setup Procedures

STEP

Preparation

An installation space and network environment must be prepared in advance.

Prepare the following manuals:

●

Documentation CD

●

Related manuals, such as manuals for the server or the networking equipment that is used

Installation Space

Installation space

Check that the installation area meets the space requirements of the rack in which the ETERNUS DX Disk storage system is to be installed.

Environmental considerations for installation

Check if the installation area for the ETERNUS DX Disk storage system meets the environmental conditions and installation environment conditions.

●

-Site Planning- "2.1 Installation Specications"

●

-Site Planning- "2.4 Installation Environment"

Power outlets

Check the type and the number of power outlets/sockets that are required to install the ETERNUS DX Disk storage system.

-Site Planning- "2.5 Outlet/Socket Specications"

Network Environment

Completing and attaching the Network Settings label

Write down the following information on the Network Settings label and attach it to the controller enclosure.

●

IP address and subnet mask for the ETERNUS DX Disk storage system

●

IP address for maintenance work

-Installation- "1.1 Connection Preparation"

Settings for the PC terminal

●

Setup Network Environment

ƪIP address: 192.168.1.2 ƪSubnet mask: 255.255.255.0

●

Set the Web browser

ƪProxy server and Cache: Disable ƪJava Script, style sheets, and cookies: Enable

-Installation- "1.2 Setup Preparation"

FUJITSU Storage ETERNUS DX60 S2 Disk storage system Read Me First

P3AM-5542-07EN

Page 7

STEP

[Left] [Right]

Installation in a Rack

The rack rail needs to be attached to the rack and the controller enclosure or the drive enclosure needs to be installed.

-Installation- "Chapter 3 Rack Installation"

IMPORTA N T

●A drive enclosure must be installed above a controller enclosure.

●The center of gravity must be taken into consideration to prevent a rack from toppling over.

The controller enclosure and the drive enclosure should generally be installed from bottom to top to lower the center of gravity and to ensure the safe use of racks.

Adjust the rack rail size to t the rack.

(Rear rack pillars)

Loosen the screws, and adjust the rack rails to the depth of the rack.

[Left]

(Front rack pillars)

Attach the rack rails to the rack.

Rack rail (for left side) "L" is stamped on the inner side of the left rack rail.

[Right]

Rack rail (for right side) "R" is stamped on the inner side of the right rack rail.

The size of the controller enclosure and the drive enclosure is 2U.

Screw holders

M5 screws

Bracket L

(Front rack pillars)

M5 screws

(Rear rack pillars)

Bracket R

Screw holders

M5 screws

Screw holders

The M5 screw positions for the rack rails are determined by the controller enclosure or the drive

enclosure base line.

Insert the M5 screws in the 1st and 3rd holes on the front and rear rack pillars above the base lines to

fasten the rack rails.

3rd position

(M5 screws)

1st position

(M5 screws)

Install the controller enclosure or the drive enclosure in the rack.

Base line

Rack rail

3rd position

(M5 screws)

1st position

(M5 screws)

IMPORTA N T

Make sure to install or remove the controller enclosure or the drive enclosure to or from a rack with

two or more people.

FUJITSU Storage ETERNUS DX60 S2 Disk storage system Read Me First

P3AM-5542-07EN

Page 8

Fasten the controller enclosure or the drive enclosure in the rack.

●2.5" Type Controller Enclosure

(1) Use the thumb screw to fasten the front right of the controller enclosure to the rack pillars.

(Rear rack pillars)

Thumb screw

(2) Attach the ange cover to the front left of the controller enclosure and use the thumb screw to

fasten it to the rack pillars.

IMPORTA N T

Thumb screw

Do not touch the power switch ( ) when attaching the ange cover.

(Rear rack pillars)

●3.5" Type Controller Enclosure/3.5" Type Drive Enclosure

(1) Use the thumb screws at the front of the controller enclosure or the drive enclosure to fasten it to

the rack.

(Rear rack pillars)

Thumb screw

(2) Attach the front cover.

IMPORTA N T

Do not touch the power switch ( ) when attaching the ange cover.

FUJITSU Storage ETERNUS DX60 S2 Disk storage system Read Me First

P3AM-5542-07EN

Page 9

STEP

Controller (CM#0) Controller (CM#1)

Cable Connection

Various cables need to be connected to the rear of the ETERNUS DX Disk storage system.

Point

IMPORTA N T

●To help with cable management and prevent incorrect connection, attach labels to the cables and

make a note of connection origins and destinations.

●This step describes dual controller type as an example. Note that there is only controller 0 (CM#0) for

single controller type.

The cables should never be bent, twisted or pulled.

LAN Cable (For Operation Management)

Connect a LAN cable (for operation management) to each MNT port.

Rear viewCable

The MNT port

-Installation- "4.1 LAN Cable Connection (For Operation Management)"

is on the right side.

Host Interface Cable

Controller Enclosure

Connect a host interface cable to each of these ports.

Rear viewCable

●

iSCSI

●

SAS

Controller Enclosure

Port#0 (left), Port#1 (right)

Controller Enclosure

Port#0 (lef t), Port#1 (right)

Controller Enclosure

Port#0 (lef t), Port#1 (right)

-Installation- "4.2 Host Inter face Connection"

FUJITSU Storage ETERNUS DX60 S2 Disk storage system Read Me First

P3AM-5542-07EN

Page 10

MiniSAS Cables

When the drive enclosure is installed, connect the DI (OUT) port of the controller enclosure to the DI (IN) port of the drive enclosure with the miniSAS cable.

Rear viewCable

●

Underside of the DI (OUT)

side plug

The " " symbol is

indented here.

●

Underside of the DI (IN)

side plug

DI (IN) port

Plug the connectors with the " " symbol indented on them

into the DI (IN) ports of the drive enclosure.

Drive Enclosure

The " " symbol is

indented here.

Plug the connectors with the " " symbol indented on them

into the DI (OUT) ports of the controller enclosure.

DI (OUT) port

-Installation- "4.3 Drive Enclosure Connection"

Power Cords

Connect the power cords to the inlets of the power supply unit. Use release ties to hold the power cords in place.

Rear viewCable

-Installation- "4.5 Power Cord Connection"

Controller Enclosure

Drive Enclosure

Controller Enclosure

FUJITSU Storage ETERNUS DX60 S2 Disk storage system Read Me First

P3AM-5542-07EN

Page 11

STEP

Basic Setup

Use ETERNUS Web GUI to perform a basic setup of the ETERNUS DX Disk storage system.

ETERNUS DX Disk Storage System and PC Terminal Connection

Connect a PC terminal to the ETERNUS DX Disk storage system. Connect the PC terminal to the MNT port of Controller 0 (CM#0) on the controller enclosure directly with the LAN cable (for operation management).

LAN port

LAN cable

PC terminal

MNT port of Controller 0 (CM#0)

Controller Enclosure

IMPORTA N T

-Installation- "5.1.1 ETERNUS DX Disk Storage System and PC Terminal Connection"

●When the LAN cable for the MNT port of Controller 0 (CM#0) is connected to a network device,

connect the cable to a PC terminal.

●Remove the LAN cable that is connected to the MNT port of Controller 1 (CM#1).

Powering On

Turn on the PC terminal and the ETERNUS DX Disk storage system.

IMPORTA N T

When turning on the ETERNUS DX

Disk storage system for the rst time,

volume formatting operation, which is set as factory default, may be performed. However, the ETERNUS DX Disk storage system setting operation can be continued.

-Installation- "5.1.2 Powering On"

Drive Enclosure

Controller Enclosure

ETERNUS Web GUI Startup

Open the Web browser on the PC terminal.

Enter either of the following URLs in the address

bar of the Web browser.

http://192.168.1.1/ https://192.168.1.1/ The logon screen for ETERNUS Web GUI appears.

Enter the Username and Password.

User name: root

Password: root (Default)

Power switch

After logging on, the Storage System Status screen of ETERNUS Web GUI appears.

-Installation- "5.1.3 Start up ETERNUS Web GUI"

FUJITSU Storage ETERNUS DX60 S2 Disk storage system Read Me First

P3AM-5542-07EN

Page 12

Initial Setup

Perform the settings that are required before operation of the ETERNUS DX Disk storage system on the [Initial Setup] screen. The [Initial Setup] screen appears by clicking the [Initial Setup] menu on the [Easy Setup] tab.

Perform the following settings according to the wizard

screen:

●

Set Date and Time

●

Set Storage System Name

●

Change Password

●

Set FC / iSCSI / SAS Port Parameters

●

Setup Network Environment

After the settings are complete, close the Web browser and then remove the LAN cable (for operation management) from the PC terminal. Connect LAN cables (for operation management) to the customer network from the MNT ports on both controller 0 and controller 1. Then start the web browser from the PC terminal that is connected to the network and log on to ETERNUS Web GUI again with the IP address that is set in "Set Network Environment".

-Installation- "5.1.4 Initial Setup"

Configuration Wizard

Perform the necessary settings to operate the ETERNUS DX Disk storage system using the Conguration

Wizard.

The [Conguration Wizard] screen appears by clicking the [Conguration Wizard] button on the [Easy Setup]

tab.

Perform the following settings according to the wizard

screen:

●

Create RAID Group

●

Create Volume

●

Dene Host

●

Congure Afnity Group

●

Dene LUN Mapping

-Installation- "5.1.5 Conguration Wizard"

Point

Default RAID groups, volumes and LUN mappings are preset in the factory. Refer to "ETERNUS Web GUI User's Guide" if the preset values are to be changed.

Assign Hot Spare

The [Assign Hot Spare] screen appears by clicking [Assign Hot Spare] under the [RAID Group Management] menu on the [Volume Settings] tab.

-Installation- "5.1.6 Assign Hot Spare"

Point

Check the factory settings and register a hot spare as required.

FUJITSU Storage ETERNUS DX60 S2 Disk storage system Read Me First

P3AM-5542-07EN

Page 13

STEP

Monitoring Setup

Perform the ETERNUS DX Disk storage system monitoring setup if required.

●

Notication of the ETERNUS DX Disk storage system problems as they occur is possible if the event notication method and level have been set.

●

If remote support is required, the ETERNUS DX Disk storage system needs to be set to notify the remote

support center of failures.

Remote support allows prompt detection and resolution of trouble.

-Installation- "5.2 ETERNUS DX Disk Storage System Monitoring Setup"

STEP

Point

Server Connection

Perform the settings required to connect to the server and install the required drivers. Perform the settings

required for network devices connecting the server and the ETERNUS DX Disk storage system.

After the server connection setup, conrm that the volumes in the ETERNUS DX Disk storage system can

be recognized by the server.

All necessary settings are complete, and the ETERNUS DX Disk storage system is now ready for normal operation.

●

-Installation- "5.3 Server Connection Setup"

●

-Server Connection-

Operation and Maintenance

Status check

The status of the ETERNUS DX Disk storage system should be regularly monitored by checking the LEDs and using ETERNUS Web GUI.

Data backup

Important data should be regularly backed up to a tape drive or similar device as a precaution against system failures.

Maintenance support period

The standard maintenance support period for ETERNUS DX Disk storage system is ve years from the date of purchase, or is dened in your service level agreement (SLA). Contact your sales representative for details if you prefer to extend

the period.

●

-Operation- "4.2 Monitoring ETERNUS DX Disk Storage System Status"

●

-Operation- "6.1 Periodic Backup"

●

-Operation- "6.4 Maintenance Service"

FUJITSU Storage ETERNUS DX60 S2 Disk storage system Read Me First

P3AM-5542-07EN

Page 14

Terms of Use

●

Applicable Environment

The ETERNUS DX Disk storage system was designed and manufactured for general ofce use, with user safety in mind. When using the ETERNUS DX

Disk storage system, follow the handling instructions, placement and cautionary notes listed in this guide. If used beyond the limits described, the users may

be at risk of personal injury and/or material damage.

●

Using the Manuals

The manuals provided with the ETERNUS DX Disk storage system contain important information regarding safe usage.

Please read this manual carefully before using the ETERNUS DX Disk storage system. Pay special at tention to "ETERNUS DX60 S2 Disk storage system

Safety Precautions", and understand the contents thoroughly before connecting.

Keep these manuals in a safe place for future reference.

Fujitsu pays careful attention to the safe use of its products to prevent user injury and/or material damage. To use the ETERNUS DX Disk storage system

properly, please follow the instructions in this manual.

●

Compliance Standards

Product safety UL60950-1, CSA-C22.2 No. 60950-1, EN60950 -1, IEC60950-1, GOST-R Electromagnetic Compatibility CNS13438(C6357) Class A, FCC CFR47 part 15 Class A, ICES-003 Class A,EN55022 Class A,

VCCI Class A , AS/NZS CISPR 22 Class A Electromagnetic Immunity EN55024 CE certication Electromagnetic Compatibility Directive 200 4/108/EC

Low Voltage Directive 2006/95/EC

Environmental compliance RoHS-compliant (Restriction of hazardous substances)

WEEE-compliant (Waste electrical and electronic equipment)

This Product is designed, developed and manufactured as contemplated for general use, including without limitation, general ofce use, personal use,

household use, and ordinary industrial use, but is not designed, developed and manufactured as contemplated for use accompanying fatal risks or dangers

that, unless extremely high safety is secured, could lead directly to death, personal injury, severe physical damage or other loss (hereinafter " High Safety

Required Use"), including without limitation, nuclear reaction control in nuclear facility, air craft ight control, air trafc control, mass transport control,

medical life support system, missile launch control in weapon system. You shall not use this Product without securing the suf cient safety required for the

High Safet y Required Use. If you wish to use this Product for High Safety Required Use, please consult with our sales representatives in charge before such

use.

Class 1 laser product

Electronic intelligence product pollution control mark of the People's Republic of China.

FUJITSU Storage ETERNUS DX60 S2 Disk storage system

Read Me First

P3AM -5542- 07EN

Date of issuance: April 2014

Issuance responsibility: FUJITSU LIMITED

● The content of this manual is subject to change without notice.

● This manual was prepared with the utmost attention to detail. However, Fujitsu shall assume no responsibility for any operational problems as the result of errors, omissions, or the use of information in this manual.

● Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual.

● The content of this manual may not be reproduced or distributed in par t or in its entirety without prior permission from Fujitsu.

FUJITSU Storage ETERNUS DX60 S2 Disk storage system Read Me First

P3AM-5542-07EN

Fujitsu ETERNUS DX60 S2 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Read Me First

Provided Manuals

Related Materials

Package Contents

Setup Procedures

Operation and Maintenance

Terms of Use