Fujitsu DG-station 100A, DG-station 100B, DG-station 100C, DG-station 100PA, DG-station 100PB User Manual

FUJITSU Network IP Pathfinder S

English Guidance Service

User Guide

Thank you for your purchase of the Fujitsu communication system.
This user guide is intended for users of its telephones and system administrators, and the
user guide explains the functions and operation of the Fujitsu communication system.
The user guide also provides important information on using this product safely.
Before using this product, read this user guide thoroughly.
Keep this user guide handy in a safe and convenient location for quick reference during use
of the product.
Fujitsu makes every effort to prevent users and bystanders from being injured and to prevent
property damage. To ensure no harm to you and bystanders, and no damage to the equipment
itself, be sure to use the product in accordance with the instructions in this user guide.

This Product is designed, developed and manufactured as contemplated for general use,

including without limitation, general of󲶻ce use, personal use, household use, and ordinary

industrial use, but is not designed, developed and manufactured as contemplated for use
accompanying fatal risks or dangers that, unless extremely high safety is secured, could
lead directly to death, personal injury, severe physical damage or other loss (hereinafter
"High Safety Required Use"), including without limitation, nuclear reaction control in
nuclear facility, aircraft flight control, air traffic control, mass transport control,
medical life support system, missile launch control in weapon system. You shall not use

this Product without securing the suf󲶻cient safety required for the High Safety Required

Use. If you wish to use this Product for High Safety Required Use, please consult with our
sales representatives in charge before such use.

CAUTION
This is a Class A product.
In a domestic environment this product may cause radio interference, in which case the
user may be required to take corrective actions. VCCI-A

● This telephone system is designed for use in Japan only and cannot be used in any

other country.

● The speci󲶻cations and information provided herein are for informational purposes

only and are not a warranty of actual performance, whether expressed or implied.
the specifications and information are subject to change without notice. Actual

performance may vary based on individual con󲶻gurations, use of collateral equipment,

or other factors.

● This telephone complies with certi󲶻cation of technical standard conformance.

This user guide prohibits copying, and transcribing the content of the description of
this user guide without the permission of the publisher.

All Rights Reserved,Copyright© Fujitsu 2017

2

IMPORTANT NOTE TO USERS

● About this user guide

The user guide also provides important information on using this product safely.
Before using this product, read this manual thoroughly.

Especially, please use this product after you read "IMPORTANT NOTE TO USERS" described in

user guide, and you understood. Moreover, please keep this book importantly.

We will explain some of telephone function on this user guide. Please see the IP Path󲶻nder S

family's user guide ( ※ ) in detail.

※ IP Path󲶻nder S family's user guide : IP Path󲶻nder RM10S GSM series, IP Path󲶻nder S

● Conventions for Alert Signals

This user guide uses the following conventions to alert users to potential injury to

themselves or bystanders and to potential property damage.

「 DANGER」 indicates a hazardous situation likely to result

DANGER

WARNING

CAUTION

in serious personal injury if the user does not perform the
procedure correctly.

WARNING」 indicates a hazardous situation could result in

「

serious personal injury if the user does not perform the
procedure correctly.

CAUTION」 indicates a hazardous situation could result in

「

minor or moderate personal injury if the user does not perform
the procedure correctly. This alert signal also indicates that
damages to the product or other property, may occur if the
user does not perform the procedure correctly.

● Safety Precautions

Follow the safety precautions given below when using the telephone, and the AC adapter (these
components are hereafter collectively referred to as the equipment). Improper handling of the
equipment or failure to observe the precautions may expose users and bystanders to harm, lead
to property damage, and may harm the environment and lead to injury and/or economic loss to
third parties.

DANGER

（ 1 ） U s e s

Notes on the AC
adapter

・ Use the dedicated AC plug of the equipment. Otherwise, a fire,

electric shock, or product failure may occur.

The dedicated AC plug

　：FC164H12（The dedicated AC plug of FC780BM）

3

IMPORTANT NOTE TO USERS

（ 1 ） U s e s

Notes on reasonably
foreseeable incorrect
uses

・ Do not spill liquid on the equipment, and do not immerse the

equipment in any liquid. Otherwise, a fire, electric shock, or
product failure may occur.

・ Do not place the equipment near vases, 󲶼owerpots, glass, toiletries,

containers of chemicals or liquids, and small metal objects. If
liquid from a container were to spill onto the equipment, or if a

foreign object were to get inside the equipment, a 󲶻re, electric

shock, or product failure may occur.

・ Be careful to not expose the equipment to insecticide or hair

spray or cleaning spray (one including in󲶼ammable) etc. Otherwise,
a 󲶻re, electric shock, or product failure may occur.

・ Ensure that no foreign object such as clips and staples gets

through openings and inside the equipment. Otherwise, a fire,
electric shock, or product failure may occur.

・ Do not place the equipment in a location that is not stable, such

as on a wobbly stand, or in a location that is at an incline.
Otherwise, the equipment may be drop off or fall over because of a
problem with balance, which may cause an injury or product failure.

・ Placing the AC adapter or the equipment in a microwave oven or

high-pressure container could cause it to generate excessive heat,
explode, or ignite, or a product failure.

WARNING

Prohibitio n a gains t
d i s a s s e m b l y a n d

modi󲶻c atio n

Notes on the
connection device

Notes on the cables

・ Do not disassemble or modify the equipment. Do not overhaul or

rebuild a used product for the purpose of reusing it. Otherwise, a

󲶻re, electric shock, or product failure may occur.

・ Do not use a modi󲶻ed device in the equipment. Otherwise, a 󲶻re,

electric shock, or product failure may occur.

・Do not damage, break, or modify the cable. Otherwise, a fire,

electric shock, or product failure may occur.

・ Ensure that no heavy or flammable object rests on the cable.

Otherwise, they may become damaged, which may result in a fire,
electric shock, or product failure.

・ Do not place the cable near a heater. Otherwise, the coating of

the cord may melt, which may result in a 󲶻re, electric shock, or

prod uct failure .

・ Do not bend the cable. Otherwise, they may become damaged, which

may result in a 󲶻re, electric shock, or product failure.

4

IMPORTANT NOTE TO USERS

（2） Maintenance and inspection

Restriction and
p r o h i b i t i o n
c o n c e r n i n g
inspection s
(maintenance
pe rso n nel)

（ 1 ） Uses

Notes on the
o p e r a t i n g
environment

・ If inspection of the inside of the equipment or repair work is

required, ask the shop where you purchased the equipment to carry
out the work. Such work may result in an electric shock, injury, or
prod uct failure .

・ If the equipment is emitting smoke or an abnormal odor, contact the

shop where you purchased the equipment after taking the following
action. For the telephone, remove the AC adapter and cable to turn
off the telephone. For the connection device, use the power switch
to turn off the system.

・ Do not place the equipment in a location where it is hot or exposed

to direct sunlight. Otherwise, the inside of the equipment becomes

hotter, which may cause a 󲶻re or product failure.

・ Do not place the equipment in a location that is extremely hot or

cold or in a location that has large 󲶼uctuations in temperature.
Otherwise, a 󲶻re, electric shock, or product failure may occur.(Use
the equipment at a temperature ranging from 0℃ to 40℃ .)

・ Do not set up or use the equipment in wet locations, such as in a

bathroom and near a humidi󲶻er. (Use the equipment in an environment
where the humidity ranges from 20% to 80%.)

・Do not place the equipment in a location where oil may splash on

it, such as near a cookstove, or in a wet or dusty location.
Otherwise, a product failure may occur.

・ Do not place the equipment on an object that tends to accumulate

static electricity, such as rugs and carpets. Otherwise, a fire,
electric shock, or product failure may occur.

・ Do not place the equipment in a location where the equipment is

exposed to harmful gases, such as sulfur gas and the exhaust gas
from automobiles. Otherwise, a fire, electric shock, or product
failure may occur.

・ Do not place the equipment in a location where the equipment is

exposed to air from a nearby sea. Otherwise, a 󲶻re, electric shock,

or product failure may occur.

CAUTION

5

IMPORTANT NOTE TO USERS

Notes on reasonably
foreseeable incorrect
uses

・ Ensure that no object rests on the equipment. The object may drop

off the equipment or fall over, which may cause a 󲶻re, electric

shock, injury, or product failure.

・ Do not place the equipment near an unstable object that is likely

to fall over easily. Such an object may drop off or fall over,

which may cause a 󲶻re, electric shock, injury, or product failure.

・ When mounting the equipment on a wall, be careful to make sure that

the equipment cannot fall off. Otherwise, a 󲶻re, electric shock,

injury, or product failure may occur.

・ Do not place the equipment in a location that is exposed to

frequent vibrations or impacts. Otherwise, the equipment may drop

off or fall down, which may cause a 󲶻re, electric shock, injury, or

prod uct failure .

・ Do not set up the equipment in a passageway. Otherwise, people may

trip over the equipment, which may result in an injury or product
failur e.

（2） Maintenance and inspection

Inspection and
clea ning

・ If drops of water are found on the equipment, wipe them up with a

dry cloth. Drops of water left on the equipment may cause a 󲶻re,

electric shock, or product failure.

・ If the equipment is dirty, clean the equipment by wiping it with a

soft dry cloth. Avoid using organic solvents, such as benzine and

thinner. Otherwise, the equipment may corrode or melt, which may

result in a 󲶻re, electric shock, or product failure.

（ 3 ） Disp osal

Notes on disposal of
the product

6

・ Please use " 事業系 ICT 製品リサイクルサービス " when this product

is abandoned and recycled from the customer of the corporation and
the enterprise. Please see the following Web site in detail.

http://jp.fujitsu.com/about/csr/eco/products/recycle/recycleindex.html
・ This equipment is products that registers or can maintain peculiar

data to the customer. When this equipment is abandoned to evade

unexpected damage etc. of the out󲶼ow of data in equipment etc. (Or,

it transfers and return it), it is necessary to delete the data
that registers or is maintained in equipment. Please contact the
purchased shop in detail.

CONTENTS

IMPORTANT NOTE TO USERS............................... 3

1　BEFORE USES

BASIC PACKAGE.......................................... 8

DIGITAL TELEPHONE CONTROLS AND INDICATORS.............. 9

CONTROL OF TONE,VOLUME,DISPLAY CONTRAST,ETC........... 11

CLEAR FACEPLATE....................................... 16

CONNECTING CABLES..................................... 16

HEARING AID........................................... 16

2　OPERATIONS

MAKING A CALL......................................... 17

ANSWERING A CALL...................................... 18

HOLDING CALLS / TRANSFER CALLS........................ 19

ABBREVIATED DIALING................................... 20

NOT PROGRAMMED ONE-TOUCH DIALING...................... 21

USEFUL OPERATIONS..................................... 22

3　LOCAL TELEPHONE DIRECTORY

TO REGISTER A DIRECTORY DATA.......................... 23

TO SEARCH LOCAL TELEPHONE DIRECTORY................... 27

TO MAKE A CALL USING THE LOCAL TELEPHONE DIRECTORY.... 29

TO CORRECT A DIRECTORY DATA

TO DELETE A DIRECTORY DATA............................ 31

TO INPUT A CHARACTER.................................. 32

............................. 30

4　CALL LOG

OUTGOING CALL LOG AND INCOMING CALL LOG............... 33

ABOUT OUTGOING CALL LOG............................... 34

ABOUT INCOMING CALL LOG............................... 35

7

1 BEFORE USES

BASIC PACKAGE

■ Digital telephone

DG-station 100A DG-station 100B 　　DG-station 100C/D/PA/PB

■ Attachment

Insert sheet for IP Path󲶻nser S

Warranty 　Safety precautions

Insert sheet for other PBX
(In case of DG-station 100A） (In case of DG-station 100B）　　(

● Please contact the purchased shop if there is an insuf󲶻cient one in the set or if there are an erratum
and an omission of a word in this book.

Clear faceplate Clear faceplate　　　　　Clear faceplate

family

In case of DG-station 100C/D/PA/PB)

■ Environmental condition

Temperature（℃） Humidity（％ RH）

Operating 0 ～＋ 40 20 ～ 80（not dewfall）

Storage － 20 ～＋ 60 5 ～ 90（not dewfall）

8

1 BEFORE USES

DIGITAL TELEPHONE CONTROLS AND INDICATORS

＜FC651D ＞

■ Face

Ringer LED

　　　　　Use these Keys to select the item

displayed in the fourth line.

Programmable Line / Feature Buttons

All buttons can be used to automatically dial
either an extension or others.

Dial Buttons

Press this Key to display the

MENU

setting menu.(See page11)

Local telephone directory can be

operated.

Use these keys to change the ringing
tone volume, speaker volume, handset
volume, display contrast, retrieval
of telephone book,and others.
(See page 11.)

Press this key to determine the
selected item.

■ Bottom

■ Back

Recording jack

Function Buttons

Handset

※ The insert sheet is option (the available accessory).
【The insert sheet of the available accessory】
・FC650TCC : Ten pieces

Microphone（only FC651D）

Line cord

Handset cord

ABBD DIAL

REDIAL

MUTE

FLASH

ICM

TRANSFER

HOLD

USB connector

Press this key for abbreviated
dialing.
Press this key to redial number.
Press this key to turn off the
microphone.
Press this key to terminate a call
without replacing the handset.
Press this key for extension call
and answering.
Press this key to transfer a call to
another telephone.
Press this key to dial without

lifting handset. Only FC651D can

use the handsfree by pressing this
button.
Press this key to hold an outside or
extension call. Press the ICM or the

LINE button to resume call.

9

1 BEFORE USES

DIGITAL TELEPHONE CONTROLS AND INDICATORS

＜FC651PA and FC651PB ＞

■ Face

　Please see ＜FC651D ＞ .

FC651PA

DP/PB
switch

Please set up the fol lowing switch
pursuant to analog network's contract
for the power outage.

(default：PB )

◆ DP：Analog sending signal 20pps

◆ PB：Analog sending signal PB

■ Bottom

FC651PA : DP/PB switch
FC651PB : P/MP switch

FC651PB

P/MP

Line cord

Handset cord

FC782PA/PB's behave in power outage

■ FC651PA and FC651PB
・During the power outage, functions (display, extension to extension calls, etc.) other than making calls

and answering calls cannot be used.

・About FC651PA/PB's behave in the power outage during the call.
　【When the power is lost】
　　If the power is lost during the call, the call will be broken. After a few seconds, you can hear the

dial tone of the analog / INS network.

【When the power is restored from the power outage】
　　If the power is restored during the call, the call will be disconnected.

After several tens of seconds, you can hear the internal dial tone.

・The call waiting service etc. of the analog/INS network cannot be used during power outage.

■ Only FC651PB
・Please set up following switch pursuant to INS network's contract for the power outage.

　　◆ MP : Point to Multi Point always-on / call-by-call (default)

◆ P : Point to Point
　P/MP swicth's con󲶻guration becomes effective if you reactivate the telephone after you change it during

power recovery.

P/MP switch's con󲶻guration doesn't become effective if you change it during power outage, or after you

reactivate the telephone.

・The line length from DSU to FC651PB (via PBX) is 300 metre ( φ 0.5 cable). One INS network line can
connect only one FC651PB.

Please set up the fol lowing switc h

switch

pursuant to INS network's contract
for the power outage.

(default：MP )

◆ MP: Point to Multi Point

always-on / call-by-call

◆ P: Point to Point

10

1 BEFORE USES

CONTROL OF TONE,VOLUME,DISPLAY CONTRAST,ETC.

Various setting is available by using the setting menu or ▲ / ▼ of 　 button.
Press MENU of button to display the setting menu.
Press ▲/▼of button to select the displayed item.
Press「戻る」button to escape from the setting menu.

The setting menu is not available for DG-station 100A since it does not have a display.　

　 RINGING TONE

You can select one of 6 tones.
You can select the tone for internal call,outside call and other call individually.

Press center of

button during ringing to select ringing tone.

る

11

1 BEFORE USES

RINGING TONE VOLUME

You can selet one of 3 levels.

1.Press ▲ / ▼ of

ringing tone volume during ringing.

Press ▲ of button to

Press ▼ of button to decrease the volume.

button to change

increase

the volume.

HANDSET VOLUME

You can select one of 7 levels.

1.Press ▲ / ▼ of

handset volume during a call using the

handset.

Press ▲ of button to increase the volume.

　Press ▼ of

button to change

button to decrease the volume.

SPEAKER VOLUME

You can select one of 8 levels.

1. Press ▲ / ▼ of

speaker volume while the spealcer is on.

Press ▲ of button to increase the volume.

　Press ▼ of

button to change

button to decrease the volume

DISPLAY CONTRAST

You can select one of 8 levels.

1.Press ▲ / ▼ of

the display contrast during on-hook.

Press ▲ of button to increase the contrast.

Press ▼ of button to decrease the contrast.

button to change

.

12