PART No. 9379069403
INSTALLATION MANUAL
OUTDOOR UNIT
For authorized service personnel only.
INSTALLATIONSANLEITUNG
AUSSENGERÄT
Nur für autorisiertes Fachpersonal.
MANUEL D’INSTALLATION
APPAREIL EXTÉRIEUR
Pour le personnel d’entretien autorisé uniquement.
MANUAL DE INSTALACIÓN
UNIDAD EXTERIOR
Únicamente para personal de servicio autorizado.
MANUALE DI INSTALLAZIONE
UNITÀ ESTERNA
A uso esclusivo del personale tecnico autorizzato.
ΕΓΧΕΙΡΙΔΙΟ ΕΓΚΑΤΑΣΤΑΣΗΣ
ΕΞΩΤΕΡΙΚΗ ΜΟΝΑΔΑ
Μόνο για εξουσιοδοτημένο τεχνικό προσωπικό.
MANUAL DE INSTALAÇÃO
UNIDADE EXTERIOR
Apenas para pessoal de assistência autorizado.
РУКОВОДСТВО ПО УСТАНОВКЕ
ВНЕШНИЙ МОДУЛЬ
Только для авторизованного обслуживающего персонала.
MONTAJ KILAVUZU
DIŞ ÜNİTE
Yalnızca yetkili servis personeli için.
AIR CONDITIONER
Português
EλληvIkά Italiano Español Français Deutsch English
Русский
Türkçe
En-1
WARNING
Installation work must be performed in accordance with national wiring standards by
authorized personnel only.
Do not use this equipment with air or any other unspecifi ed refrigerant in the refrigerant
lines.
Excess pressure can cause a rupture.
During installation, make sure that the refrigerant pipe is attached fi rmly before you run
the compressor.
Do not operate the compressor under the condition of refrigerant piping not attached
properly with 3-way valve open. This may cause abnormal pressure in the refrigeration
cycle that leads to rupture and even injury.
When installing and relocating the air conditioner, do not mix gases other than the
specifi ed refrigerant (R410A) to enter the refrigerant cycle.
If air or other gas enters the refrigerant cycle, the pressure inside the cycle will rise to
an abnormally high value and cause rupture, injury, etc.
Do not remove the connection pipe while the compressor is in operation with 3-way
valve open.
This may cause abnormal pressure in the refrigeration cycle that leads to rupture and
even injury.
For the air conditioner to operate satisfactorily, install it as outlined in this installation
manual.
Connect the indoor unit and outdoor unit with the air conditioner piping and cable
available standards parts.
This installation manual describes the correct connections using the installation set
available from our standard parts.
Also, do not use an extension cable.
Do not purge the air with refrigerants but use a vacuum pump to vacuum the installation.
There is not extra refrigerant in the outdoor unit for air purging.
Use a vacuum pump for R410A exclusively.
Using the same vacuum pump for different refrigerants may damage the vacuum pump
or the unit.
Use a clean gauge manifold and charging hose for R410A exclusively.
During the pump-down operation, make sure that the compressor is turned off before
you remove the refrigerant piping.
Do not remove the connection pipe while the compressor is in operation with 3-way
valve open.
This may cause abnormal pressure in the refrigeration cycle that leads to rupture and
even injury.
CAUTION
Read carefully all security information before use or install the air conditioner.
Do not attempt to install the air conditioner or a part of the air conditioner by yourself.
This unit must be installed by qualifi ed personnel with a capacity certifi cate for handling
refrigerant fl uids. Refer to regulation and laws in use on installation place.
The installation must be carried out in compliance with regulations in force in the place
of installation and the installation instructions of the manufacturer.
This unit is part of a set constituting an air conditioner. It must not be installed alone or
with non-authorized by the manufacturer.
Always use a separate power supply line protected by a circuit breaker operating on all
wires with a distance between contact of 3mm for this unit.
The unit must be correctly earthed (grounded) and the supply line must be equipped
with a differential breaker in order to protect the persons.
The units are not explosion proof and therefore should not be installed in explosive
atmosphere.
This unit contains no user-serviceable parts. Always consult authorized service
personnel to repairs.
When moving, consult authorized service personnel for disconnection and installation of
the unit.
Children should be monitored to ensure they do not play with the device.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they do
not play with the appliance.
Do not touch the aluminum fi ns of heat exchanger built-in the indoor or outdoor unit to
avoid personal injury when you install or maintain the unit.
Do not place any other electrical products or household belongings under indoor unit or
outdoor unit. Dripping condensation from the unit might get them wet, and may cause
damage or malfunction of your property.
Contents
1. SAFETY PRECAUTIONS ............................................................................................1
2. ABOUT THE UNIT .......................................................................................................2
2.1. Precautions for using R410A refrigerant ............................................................2
2.2. Special tools for R410A ......................................................................................2
2.3. Accessories ........................................................................................................2
2.4. Operating range ................................................................................................. 2
3. INSTALLATION WORK ...............................................................................................2
3.1. Selecting an installation location ........................................................................2
3.2. Drain installation ................................................................................................. 3
3.3. Installation dimensions .......................................................................................3
3.4. Transporting the unit ..........................................................................................4
3.5. Installation .......................................................................................................... 4
4. PIPE SELECTION .......................................................................................................4
4.1. Selecting the pipe material ................................................................................. 4
4.2. Protection of pipes .............................................................................................5
4.3. Refrigerant pipe size and allowable piping length .............................................. 5
4.4. Connectable pipe diameter and max. piping length ........................................... 5
5. PIPE INSTALLATION-1 ...............................................................................................5
5.1. Opening a knock out hole ..................................................................................5
5.2. Brazing ............................................................................................................... 5
5.3. Flare connection (pipe connection) ....................................................................5
5.4. Sealing test ........................................................................................................6
5.5. Vacuum process ................................................................................................7
5.6. Additional charging ............................................................................................. 7
6. ELECTRICAL WIRING ................................................................................................7
6.1. Notes for electrical wiring ...................................................................................7
6.2. Selecting circuit breaker and wiring ...................................................................8
6.3. Knock out holes for wiring ..................................................................................8
6.4. Wiring method .................................................................................................... 9
7. PIPE INSTALLATION-2 ..............................................................................................9
7.1. Installing insulation .............................................................................................9
7.2. Filling with putty ..................................................................................................9
8. HOW TO OPERATE DISPLAY UNIT .........................................................................10
8.1. Various setting methods ...................................................................................10
8.2. Description of display .......................................................................................10
9. LOCAL SETTING ......................................................................................................10
9.1. Low noise mode (Local work) ..........................................................................10
9.2. Peak cut mode (Local work) .............................................................................11
10. TEST RUN .................................................................................................................12
10.1. Check items before performing the test run .....................................................12
10.2. Test run method ...............................................................................................12
11. PUMP DOWN ............................................................................................................ 12
11.1. Preparation for pump down .............................................................................. 13
11.2. Pump down procedure .....................................................................................13
12. ERROR CODE DISPLAY ..........................................................................................13
12.1. How to check error code ..................................................................................13
12.2. Error code check table .....................................................................................14
1. SAFETY PRECAUTIONS
Be sure to read this manual carefully before installation.•
The warnings and precautions indicated in this manual contain important information •
pertaining to your safety. Be sure to observe them.
Hand this manual, together with the operating manual, to the customer. Request the •
customer to keep them on hand for future use, such as for relocating or repairing the
unit.
WARNING
This mark indicates procedures which, if improperly performed,
might lead to the death or serious injury of the user.
CAUTION
This mark indicates procedures which, if improperly performed,
might possibly result in personal harm to the user, or damage to
property.
WARNING
Never touch electrical components immediately after the power supply has been turned
off. Electrical shock may occur. After turning off the power, always wait 10 minutes or
more before touching electrical components.
Request your dealer or a professional installer to install the outdoor unit in accordance
with this installation manual. an improperly installed unit can cause serious accidents
such as water leakage, electric shock, or fi re.
If the outdoor unit is installed in disregard of the instructions in the installation manual, it
will void the manufacturer’s warranty.
Do not turn ON the power until all work has been completed. Turning ON the power
before the work is completed can cause serious accidents such as electric shock or fi re.
If refrigerant leaks while work is being carried out, ventilate the area. If the refrigerant
comes in contact with a fl ame, it produces a toxic gas.
INSTALLATION MANUAL
OUTDOOR UNIT
PART No. 9379069403 English
En-2
2.3. Accessories
WARNING
For installation purposes, be sure to use the parts supplied by the manufacturer or other
prescribed parts. The use of non-prescribed parts can cause serious accidents such as
the unit falling, water leakage, electric shock, or fi re.
Following installation parts are supplied. Use them as required.
Keep this manual in a safe place, and do not discard any other accessories until the
installation work has been completed.
Name and shape Q’ty Description
Installation
manual
1
This manual
Drain pipe
1
For outdoor unit drain piping work
(May not be supplied, depending on
the model.)
Drain cap
2
One-touch bush
2
For power supply cable and
connection cable installation
2.4. Operating range
Outdoor Cooling/Dry Mode Heating Mode
Temperature About -15 °C to 46 °C About -15 °C to 24 °C
3. INSTALLATION WORK
Make sure to obtain the customer’s approval for selecting and installing the outdoor unit.
3.1. Selecting an installation location
WARNING
Securely install the outdoor unit at a location that can withstand the weight of the unit.
Otherwise, the outdoor unit may fall and cause injury.
Be sure to install the outdoor unit as prescribed, so that it can withstand earthquakes
and typhoons or other strong winds. Improper installation can cause the unit to topple or
fall, or other accidents.
Do not install the outdoor unit near the edge of a balcony. Otherwise, children may climb
onto the outdoor unit and fall off of the balcony.
CAUTION
Do not install the outdoor unit in the following areas:
Area with high salt content, such as at the seaside. It will deteriorate metal parts, •
causing the parts to fail or the unit to leak water.
Area fi lled with mineral oil or containing a large amount of splashed oil or steam, •
such as a kitchen. It will deteriorate plastic parts, causing the parts to fail or the unit
to leak water.
Area that generates substances that adversely affect the equipment, such as sulfuric •
gas, chlorine gas, acid, or alkali. It will cause the copper pipes and brazed joints to
corrode, which can cause refrigerant leakage.
Area containing equipment that generates electromagnetic interference. It will cause •
the control system to malfunction, preventing the unit from operating normally.
Area that can cause combustible gas to leak, contains suspended carbon fi bers or •
fl ammable dust, or volatile infl ammables such as paint thinner or gasoline. If gas
leaks and settles around the unit, it can cause a fi re.
Area where small animals may live. It may cause failure, smoke or fi re if small •
animals enter and touch internal electrical parts.
Area where animals may urinate on the unit or ammonia may be generated.•
Do not tilt the outdoor unit more than 3 degrees.
Install the outdoor unit in a well-ventilated location away from rain or direct sunlight.
If the outdoor unit must be installed in an area within easy reach of the general public,
install as necessary a protective fence or the like to prevent their access.
Install the outdoor unit in a location that would not inconvenience your neighbors, as
they could be affected by the airfl ow coming out from the outlet, noise, or vibration. If it
must be installed in proximity to your neighbors, be sure to obtain their approval.
If the outdoor unit is installed in a cold region that is affected by snow accumulation,
snow fall, or freezing, take appropriate measures to protect it from those elements.
To ensure a stable operation, install inlet and outlet ducts.
2. ABOUT THE UNIT
d
2.1. Precautions for using R410A refrigerant
WARNING
Do not introduce any substance other than the prescribed refrigerant into the
refrigeration cycle. If air enters the refrigeration cycle, the pressure in the refrigeration
cycle will become abnormally high and cause the piping to rupture.
If there is a refrigerant leak, make sure that it does not exceed the concentration limit.
If a refrigerant leak exceeds the concentration limit, it can lead to accidents such as
oxygen starvation.
Do not touch refrigerant that has leaked from the refrigerant pipe connections or other
areas. Touching the refrigerant directly can cause frostbite.
If a refrigerant leak occurs during operation, immediately vacate the premises and
thoroughly ventilate the area. If the refrigerant comes in contact with a fl ame, it produces
a toxic gas.
The basic installation work procedures are the same as conventional refrigerant models.
However, pay careful attention to the following points:
Since the working pressure is 1.6 times higher than that of conventional refrigerant •
(R22) models, some of the piping and installation and service tools are special. (See
the table below.)
Especially, when replacing a conventional refrigerant (R22) model with a new
refrigerant R410A model, always replace the conventional piping and fl are nuts with
the R410A piping and fl are nuts.
Models that use refrigerant R410A have a different charging port thread diameter •
to prevent erroneous charging with conventional refrigerant (R22) and for safety.
Therefore, check beforehand. [The charging port thread diameter for R410A is 1/2
UNF 20 threads per inch.]
Be careful that foreign matter (oil, water, etc.) does not enter the piping than with •
refrigerant models. Also, when storing the piping, securely seal the openings by
pinching, taping, etc.
When charging the refrigerant, take into account the slight change in the composition •
of the gas and liquid phases. And always charge from the liquid phase where
refrigerant composition is stable.
2.2. Special tools for R410A
WARNING
To install a unit that uses R410A refrigerant, use dedicated tools and piping materials
that have been manufactured specifi cally for R410A use. Because the pressure of
R410A refrigerant is approximately 1.6 times higher than R22, failure to use dedicated
piping material or improper installation can cause rupture or injury. Furthermore, it can
cause serious accidents such as water leakage, electric shock, or fi re.
Tool name Changes
Gauge manifold Pressure is high and cannot be measured with a conventional
gauge. To prevent erroneous mixing of other refrigerants, the
diameter of each port has been changed.
It is recommended the gauge with seals –0.1 to 5.3 MPa (-1 to
53 bar) for high pressure. –0.1 to 3.8 MPa (-1 to 38 bar) for low
pressure.
Charging hose To increase pressure resistance, the hose material and base
size were changed.
Vacuum pump A conventional vacuum pump can be used by installing a
vacuum pump adapter.
Gas leakage detector Special gas leakage detector for HFC refrigerant R410A.
Copper pipes
It is necessary to use seamless copper pipes and it is desirable that the amount of residual
oil is less than 40 mg/10 m. Do not use copper pipes having a collapsed, deformed or
discolored portion (especially on the interior surface). Otherwise, the expansion valve or
capillary tube may become blocked with contaminants.
As an air conditioner using R410A incurs pressure higher than when using conventional
refrigerant, it is necessary to choose adequate materials.
Thicknesses of copper pipes used with R410A are as shown in the table. Never use
copper pipes thinner than that in the table even when it is available on the market.
Thicknesses of Annealed Copper Pipes (R410A)
Pipe outside diameter [mm (in.)] Thickness [mm]
6.35 (1/4) 0.80
9.52 (3/8) 0.80
12.70 (1/2) 0.80
15.88 (5/8) 1.00
19.05 (3/4) 1.20
En-3
CAUTION
Install the outdoor unit in a location that is away from exhaust or the vent ports that
discharge vapor, soot, dust, or debris.
Install the indoor unit, outdoor unit, power supply cable, transmission cable, and remote
control cable at least 1 m away from a television or radio receivers. The purpose of this
is to prevent TV reception interference or radio noise. (Even if they are installed more
than 1 m apart, you could still receive noise under some signal conditions.)
Branch switch and
circuit breaker
1 m or more
1 m or more
Branch switch and
circuit breaker
If children under 10 years old may approach the unit, take preventive measures so that
they cannot reach the unit.
Keep the length of the piping of the indoor and outdoor units within the allowable range.
For maintenance purposes, do not bury the piping.
3.2. Drain installation
CAUTION
Perform drain work in accordance with this Manual, and ensure that the drain water is
properly drained. If the drain work is not carried out correctly, water may drip down from
the unit, wetting the furniture.
When the outdoor temperature is 0 °C or less, do not use the accessory drain pipe
and drain cap. If the drain pipe and drain cap are used, the drain water in the pipe may
freeze in extremely cold weather. (Reverse cycle model only)
As the drain water fl ows out of the outdoor unit during heating operation, install the •
drain pipe and connect it to a commercial 16 mm hose. (Reverse cycle model only)
When installing the drain pipe, plug all the holes other than the drain pipe mounting •
hole in the bottom of the outdoor unit with putty so there is no water leakage. (Reverse
cycle model only)
(Unit : mm)
Drain cap mounting hole
AIR
Drain pipe mounting hole
302
265
188
51
439
623
Base
Drain pipe
Drain pipe mounting hole
а
3.3. Installation dimensions
CAUTION
The installation space shown in the following examples is based on an ambient
temperature under cooling operation of 35 °C (DB) at the air intake of the outdoor unit.
Provide more space around the air intake than shown in the examples if the ambient
temperature exceeds 35 °C (DB) or if the thermal load of all of the outdoor units exceeds
the capacity.
Consider the transportation route, installation space, maintenance space, and access,
and install the unit in a location with suffi cient space for the refrigerant piping.
CAUTION
Observe the installation space specifi cations that are shown in the fi gures.
Keep the same space at rear air intake.
Provide the same space for the air intake at the rear of the outdoor unit.
If the installation is not performed according to the specifi cations, it could cause a short
circuit and result in a lack of operating performance. As a result, the outdoor unit might
easily be stopped by high-pressure protection.
Air intake
Rear view
Installation methods not shown in the following examples are not recommended.
Performance may drop signifi cantly.
3.3.1. Single outdoor unit installation
When the upward area is open (Unit : mm)
(1) Obstacles at rear only
150
(2) Obstacles at rear and sides only
200
300
200
(3) Obstacles at front only
1000 or more
(4) Obstacles at front and rear only
1000 or more
150
When an obstruction is present also in the upward area (Unit : mm)
(1) Obstacles at rear and above only
300
Max. 500
1000
(2) Obstacles at rear, sides, and above only
1500
250
250
500
Max. 500
3.3.2. Multiple outdoor unit installation
Provide at least 15 mm of space between the outdoor units if multiple units are •
installed.
When routing the piping from the side of an outdoor unit, provide space for the piping.•
No more than 3 units must be installed side by side. When 3 units or more are •
arranged in a line, provide the space as shown in the following example when an
obstruction is present also in the upward area.
When the upward area is open (Unit : mm)
(1) Obstacles at rear only
300
(2) Obstacles at front only
1500 or more
En-4
(3) Obstacles at front and rear only
500
1500 or more
When an obstruction is present also in the upward area (Unit : mm)
Obstacles at rear and above only
1500
500
Max. 300
1500
3.3.3. Outdoor units installation in multi row (Unit : mm)
(1) Single parallel unit arrangement
150
600
1000
2000 or more
(2) Multiple parallel unit arrangement
500
600
1500
3000 or more
3.4. Transporting the unit
WARNING
Do not touch the fi ns.
Otherwise, personal injury could result.
CAUTION
When carrying the unit, hold the handles on the right and left sides and be careful.
If the outdoor unit is carried from the bottom, hands or fi ngers may be pinched.
Carry slowly in the manner as shown on “Fig. B” holding the handles “Fig. A” in right •
and left sides. (Be careful not to touch with hands or objects.)
Be sure to hold the handles on the sides of the unit. Otherwise, the suction grilles on •
the sides of the unit may be deformed.
Fig. A
Handle
Suction grille
Handle
Suction grille
Fig. B
Front view
Rear view
3.5. Installation
(Unit : mm)
4 - Φ 12 Hole
132
AIR
650 119
50 50
16
370
Install 4 anchor bolts at the locations indicated with arrows in the above fi gure.•
To reduce vibration, do not install the unit directly on the ground. Install it on a secure •
base (such as concrete blocks).
The foundation shall support the legs of the unit and have a width of 50 mm or more.•
Depending on the installation conditions, the outdoor unit may spread its vibration •
during operation, which may cause noise and vibration. Therefore, attach damping
materials (such as damping pads) to the outdoor unit during installation.
Install the foundation, making sure that there is enough space for installing the •
connection pipes.
Secure the unit to a solid block using foundation bolts. (Use 4 sets of commercially •
available M10 bolts, nuts, and washers.)
The bolts should protrude 20 mm. •
(Refer to the fi gure below.)
If overturning prevention is required, purchase the necessary commercially available •
items.
Bolt
20 mm
Nut
Base
Fix securely with bolts on a solid block. (Use 4 sets of commercially available M10 bolt,
nut and washer.)
4. PIPE SELECTION
4.1. Selecting the pipe material
CAUTION
Do not use existing pipes.
Use pipes that have clean external and internal sides without any contamination which
may cause trouble during use, such as sulfur, oxide, dust, cutting waste, oil, or water.
It is necessary to use seamless copper pipes.
Material: Phosphor deoxidized seamless copper pipes.
It is desirable that the amount of residual oil is less than 40 mg/10 m.
Do not use copper pipes that have a collapsed, deformed, or discolored portion
(especially on the interior surface). Otherwise, the expansion valve or capillary tube may
become blocked with contaminants.
Improper pipe selection will degrade performance. As an air conditioner using R410A
incurs pressure higher than when using conventional refrigerant, it is necessary to
choose adequate materials.
Note:
Thicknesses of copper pipes used with R410A are as shown in the table.
Never use copper pipes thinner than those indicated in the table even if they are available
on the market.
En-5
Thicknesses of Annealed Copper Pipes (R410A)
Pipe outside diameter
[mm (in.)]
Thickness
[mm]
6.35 (1/4)
0.89.52 (3/8)
12.70 (1/2)
15.88 (5/8) 1.0
19.05 (3/4) 1.2
4.2. Protection of pipes
Protect the pipes to prevent the entry of moisture and dust.
Especially, pay attention when passing the pipes through a hole or connecting the end of
a pipe to the outdoor unit.
Location Working period Protection method
Outdoor
1 month or more Pinch pipes
Less than 1 month Pinch or tape pipes
Indoor - Pinch or tape pipes
4.3. Refrigerant pipe size and allowable piping length
CAUTION
Keep the piping length between the indoor unit and outdoor unit within the allowable
tolerance.
Pipe diameter <Liquid/Gas>
(Standard)
[mm (in.)]
9.52 (3/8) / 15.88 (5/8)
Max. piping length (L1)
[m]
75
*1
Min. piping length (L1)
[m]
5
Max. height difference (H1)
<Indoor unit to outdoor unit>
[m]
30
View (Example)
L1
H1
*1: For the standard pipe diameter.
4.4. Connectable pipe diameter and max. piping length
The fi gures enclosed by a thick-lined frame indicate the standard pipe diameter and max.
piping length.
Pipe diameter
[mm (in.)]
Liquid pipes 9.52 (3/8) 12.70 (1/2)
Gas pipes
15.88
(5/8)
19.05
(3/4)
15.88
(5/8)
19.05
(3/4)
Piping length
[m (m)]
Max. piping length < L1 >
*1
(Pre-charge length)
75
[30]
50
[30]
35
[15]
35
[15]
*1: Refer to “View” in the table of “4.3. Refrigerant pipe size and allowable piping length”.
5. PIPE INSTALLATION-1
5.1. Opening a knock out hole
CAUTION
Be careful not to deform or scratch the panel while opening the knock out holes.
To protect the piping insulation after opening a knock out hole, remove any burrs from
the edge of the hole. It is recommended to apply rust prevention paint to the edge of the
hole.
Pipes can be connected from 4 directions, front, lateral side, rear side and bottom. •
(Fig. A)
When connecting at the bottom, remove the service panel and piping cover on the •
front of the outdoor unit, and open the knock out hole provided at the bottom corner of
the piping outlet.
It can be installed as shown on “Fig. B” cutting out the 2 slits as indicated on “Fig. C”. •
(When cutting slits, use a steel saw.)
Fig. A
Service panel
Front
connection
Bottom
connection
(No. 1)
Lateral
connection
Rear
connection
Fig. B Fig. C
Slit
Slit
Bottom
connection
(No. 2)
5.2. Brazing
CAUTION
If air or another type of refrigerant enters the refrigeration cycle, the internal pressure in
the refrigeration cycle will become abnormally high and prevent the unit from exerting its
full performance.
Apply nitrogen gas while brazing the pipes. If a pipe is brazed without applying nitrogen
gas, an oxidation fi lm will be created.
This can degrade performance or damage the
parts in the unit (such as the compressor or
valves).
Pressure regulating valve
Cap
Brazing area
Nitrogen gas
Nitrogen gas pressure: 0.02 MPa
(= pressure felt suffi ciently on
the back of the hand)
For brazing material, use phosphor copper that does not require fl ux. Do not use fl ux to
braze pipes. If the fl ux is the chlorine type, it will cause the pipes to corrode.
Furthermore, if the fl ux contains fl uoride, it will adversely affect the refrigerant pipe
system such as by degrading the refrigerant.
If fl uoride is contained, quality of refrigerant deteriorates and affects the refrigerant
piping system.
5.3. Flare connection (pipe connection)
CAUTION
Do not use mineral oil on a fl ared part. Prevent mineral oil from getting into the system
as this would reduce the lifetime of the units.
While welding the pipes, be sure to blow dry nitrogen gas through them.
The maximum lengths of this product are shown in the table. If the units are further apart
than this, correct operation cannot be guaranteed.
En-6
5.3.1. Flaring
Use special pipe cutter and fl are tool exclusive for R410A.
(1) Cut the connection pipe to the necessary length with a pipe cutter.
(2) Hold the pipe downward so that the cuttings will not enter the pipe and remove any
burrs.
(3) Insert the fl are nut (always use the fl are nut attached to the indoor and outdoor
units respectively) onto the pipe and perform the fl are processing with a fl are tool.
Leakage of refrigerant may result if other fl are nuts are used.
(4) Protect the pipes by pinching them or with tape to prevent dust, dirt, or water from
entering the pipes.
Check if [L] is fl ared uniformly
and is not cracked or scratched.
B
L
Pipe
A
Die
Pipe outside diameter
[mm (in.)]
Dimension A [mm]
Flare tool for R410A, clutch type
6.35 (1/4)
0 to 0.5
9.52 (3/8)
12.70 (1/2)
15.88 (5/8)
19.05 (3/4)
Pipe outside diameter
[mm (in.)]
Dimension B
0
[mm]
- 0.4
6.35 (1/4) 9.1
9.52 (3/8) 13.2
12.70 (1/2) 16.6
15.88 (5/8) 19.7
19.05 (3/4) 24.0
When using conventional fl are tools to fl are R410A pipes, the dimension A should be
approximately 0.5 mm more than indicated in the table (for fl aring with R410A fl are tools)
to achieve the specifi ed fl aring. Use a thickness gauge to measure the dimension A.
Pipe outside
diameter [mm (in.)]
Width across fl ats
of Flare nut [mm]
6.35 (1/4) 17
9.52 (3/8) 22
12.70 (1/2) 26
15.88 (5/8) 29
19.05 (3/4) 36
Width across fl ats
5.3.2. Bending pipes
CAUTION
To prevent breaking of the pipe, avoid sharp bends. Bend the pipe with a radius of
curvature of 100 mm to 150 mm.
If the pipe is bent repeatedly at the same place, it will break.
If pipes are shaped by hand, be careful not to collapse them.•
Do not bend the pipes at an angle of more than 90°.•
When pipes are repeatedly bent or stretched, the material will harden, making it diffi cult •
to bend or stretch them any more.
Do not bend or stretch the pipes more than three times.•
5.3.3. Pipe connection
CAUTION
Be sure to install the pipe against the port on the indoor unit and the outdoor unit
correctly. If the centering is improper, the fl are nut cannot be tightened smoothly. If the
fl are nut is forced to turn, the threads will be damaged.
Do not remove the fl are nut from the outdoor unit pipe until immediately before
connecting the connection pipe.
After installing the piping, make sure that the connection pipes do not touch the
compressor or outer panel. If the pipes touch the compressor or outer panel, they will
vibrate and produce noise.
(1) Detach the caps and plugs from the pipes.
(2) Center the pipe against the port on the outdoor unit, and then turn the fl are nut by
hand.
(3) Tighten the fl are nut of the connection pipe at the outdoor unit valve connector.
3-way valve (Liquid)
3-way valve (Gas)
Flare nut
Connection pipe
(Liquid)
Flare nut
Connection pipe
(Gas)
(4) After tightening the fl are nut by hand, use a torque wrench to fully tighten it.
CAUTION
Hold the torque wrench at its grip, keeping it in a right angle with the pipe, in order to
tighten the fl are nut correctly.
Outer panel may be distorted if fastened only with a wrench. Be sure to fi x the •
elementary part with a spanner and fasten with a wrench (refer to below diagram).
Do not apply force to the blank cap of the valve or hang a wrench, etc., on the cap. It •
may cause leakage of refrigerant.
Blank cap
Flare nut
Torque wrench
Holding
wrench
Torque wrench
90°
Flare nut
[mm (in.)]
Tightening torque
[N·m (kgf·cm)]
6.35 (1/4) dia. 16 to 18 (160 to 180)
9.52 (3/8) dia. 32 to 42 (320 to 420)
12.70 (1/2) dia. 49 to 61 (490 to 610)
15.88 (5/8) dia. 63 to 75 (630 to 750)
19.05 (3/4) dia. 90 to 110 (900 to 1100)
5.3.4. Handling precautions for the valves
Mounted part of Blank cap is sealed for protection.•
Fasten blank cap tightly after opening valves.•
Table A
Blank cap
[mm (in.)]
Tightening torque
[N·m (kgf·cm)]
6.35 (1/4) 20 to 25 (200 to 250)
9.52 (3/8) 20 to 25 (200 to 250)
12.70 (1/2) 25 to 30 (250 to 300)
15.88 (5/8) 30 to 35 (300 to 350)
19.05 (3/4) 35 to 40 (350 to 400)
Operating the valves
Use a hexagon wrench (size 4 mm).•
Opening (1) Insert the hexagon wrench into the valve shaft, and turn it •
counterclockwise.
(2) Stop turning when the valve shaft can no longer be turned.
(Open position)
Closing (1) Insert the hexagon wrench into the valve shaft, and turn it clockwise.•
(2) Stop turning when the valve shaft can no longer be turned.
(Closed position)
Opening direction
Hexagon wrench
Seal (blank cap
installation portion)
Liquid pipe
Gas pipe
Opening direction
5.4. Sealing test
WARNING
Before operating the compressor, install the pipes and securely connect them.
Otherwise, if the pipes are not installed and if the valves are open when the compressor
operates, air could enter the refrigeration cycle. If this happens, the pressure in the
refrigeration cycle will become abnormally high and cause damage or injury.
After the installation, make sure there is no refrigerant leakage. If the refrigerant leaks
into the room and becomes exposed to a source of fi re such as a fan heater, stove, or
burner, it produces a toxic gas.
Do not subject the pipes to strong shocks during the sealing test. It can rupture the
pipes and cause serious injury.
CAUTION
Do not block the walls and the ceiling until the sealing test and the charging of the
refrigerant gas have been completed.
For maintenance purposes, do not bury the piping of the outdoor unit.
After connecting the pipes, perform a sealing test.•
Make sure that the 3-way valves are closed before performing a sealing test.•
Pressurize nitrogen gas to 4.15 MPa to perform the sealing test.•
Add nitrogen gas to both the liquid pipes and the gas pipes.•
Check all fl are connections and welds. Then, check that the pressure has not •
decreased.
Compare the pressures after pressurizing and letting it stand for 24 hours, and check •
that the pressure has not decreased.
* When the outdoor air temperature changes 5 °C, the test pressure changes
0.05 MPa. If the pressure has dropped, the pipe joints may be leaking.
If a leak is found, immediately repair it and perform the sealing test again.•
After completing the sealing test, release the nitrogen gas from both valves.•
Release the nitrogen gas slowly.•
En-7
5.5. Vacuum process
CAUTION
Perform a refrigerant leakage test (air tightness test) to check for leaks using nitrogen
gas while all valves in the outdoor unit are closed. (Use the test pressure indicated on
the nameplate.)
Be sure to evacuate the refrigerant system using a vacuum pump.
The refrigerant pressure may sometimes not rise when a closed valve is opened after
the system is evacuated using a vacuum pump. This is caused by the closure of the
refrigerant system of the outdoor unit by the electronic expansion valve. This will not
affect the operation of the unit.
If the system is not evacuated suffi ciently, its performance will drop.
Use a clean gauge manifold and charging hose that were designed specifi cally for use
with R410A. Using the same vacuum equipment for different refrigerants may damage
the vacuum pump or the unit.
Do not purge the air with refrigerants, but use a vacuum pump to evacuate the system.
(1) Check that the valves are closed by removing the blank caps from the gas and
liquid pipes.
(2) Remove the charging port cap, and connect the gauge manifold and the vacuum
pump to the charging valve with the service hoses.
(3) Vacuum the indoor unit and the connecting pipes until the pressure gauge indicates
–0.1 MPa (–76 cmHg).
(4) When –0.1 MPa (–76 cmHg) is reached, operate the vacuum pump for at least
60 minutes.
(5) Disconnect the service hoses and fi t the charging port cap to the charging valve to
the specifi ed torque. (Refer to below table)
(6) Remove the blank caps, and fully open the 3-way valves with a hexagon wrench
[Torque: 6 to 7 N·m (60 to 70 kgf·cm)].
(7) Tighten the blank caps of the 3-way valve to the specifi ed torque. (Refer to Table A
on page 6.)
Tightening torque [N·m (kgf·cm)]
Charging port cap 10 to 12 (100 to 120)
Service hose
Service hose with valve core
Charging port
Blank cap
Hexagon wrench
Connecting pipe
Gauge manifold
Vacuum pump
Charging port cap
3-way valve
Use a 4 mm
hexagon
wrench
Pressure regulating valve
Pressure gauge
Nitrogen
Indoor unit
Outdoor unit
Vacuum pump
5.6. Additional charging
WARNING
When moving and installing the air conditioner, do not mix gas other than the specifi ed
refrigerant R410A inside the refrigerant cycle.
If air or other gas enters the refrigerant cycle, the pressure inside the cycle will rise to an
abnormally high value and cause breakage, injury, etc.
CAUTION
After vacuuming the system, add refrigerant.
Do not reuse recovered refrigerant.
When charging the refrigerant R410A, always use an electronic scales for refrigerant
charging (to measure the refrigerant by weight). Adding more refrigerant than the
specifi ed amount will cause a malfunction.
CAUTION
When charging the refrigerant, take into account the slight change in the composition
of the gas and liquid phases, and always charge from the liquid phase side whose
composition is stable. Adding refrigerant through the gas pipe will cause a malfunction.
Check if the steel cylinder has a siphon installed or not before fi lling. (There is an
indication “with siphon for fi lling liquid” on the steel cylinder.)
Filling method for cylinder with siphon
R410A
Gas
Liquid
Set the cylinder vertical and fi ll with the liquid.
(Liquid can be fi lled without turning bottom up with the
siphon inside.)
Filling method for other cylinders
R410A
Gas
Liquid
Turn bottom up and fi ll with liquid.
(Be careful to avoid turning over the cylinder.)
Be sure to use the special tools for R410A for pressure resistance and to avoid mixing
of impure substances.
If the units are further apart than the maximum pipe length, correct operation can not be
guaranteed.
Make sure to back closing valve after refrigerant charging. Otherwise, the compressor
may fail.
Minimize refrigerant release to the air. Excessive release is prohibited under the Freon
Collection and Destruction Law.
5.6.1. For Pre-charge lengths
Refrigerant pipe size Piping length (L) *Pre-charge [m]
Standard 30
Size up (Liquid pipe) 15
5.6.2. If additional refrigerant is required
When the piping is longer than pre-charge length, additional charging is necessary.•
For the additional amount, see the table below.•
Additional charging amount
Single type
L1 (*1) > Pre-charge length
Refrigerant pipe size
[mm (in.)]
Piping length
Standard
~30 m 40 m 50 m 60 m 70 m g/m
Liquid 9.52 (3/8)
None 500 g 1,000 g 1,500 g 2,000 g 50 g/m
Gas 15.88 (5/8)
Size up
~30 m 40 m 50 m g/m
Liquid 9.52 (3/8)
None 500 g 1,000 g 50 g/m
Gas 19.05 (3/4)
~15 m 25 m 35 m g/m
Liquid 12.70 (1/2)
None 1,000 g 2,000 g 100 g/m
Gas
15.88 (5/8)
19.05 (3/4)
*1: Refer to “View” in the table of “4.3. Refrigerant pipe size and allowable piping length”.
s d
6. ELECTRICAL WIRING
6.1. Notes for electrical wiring
WARNING
Wiring connections must be performed by a qualifi ed person in accordance with
the specifi cations. The voltage rating for this product is 400 V at 50 Hz. It should be
operated within the range of 342 to 456 V.
Before connecting the wires, make sure the power supply is OFF.
Use a dedicated power supply circuit. Insuffi cient power capacity in the electrical circuit
or improper wiring may cause electric shock or fi re.
Install a breaker at the power supply for each outdoor unit. Improper breaker selection
can cause electric shock or fi re.
Install a leakage circuit breaker in accordance with the related laws and regulations. An
improperly installed electrical box cover can cause serious accidents such as electric
shock or fi re through exposure to dust or water.
A circuit breaker is installed in the permanent wiring. Always use a circuit that can trip
all the poles of the wiring and has an isolation distance of at least 3 mm between the
contacts of each pole.
Use designated cables and power cables. Improper use may cause electric shock or fi re
by poor connection, insuffi cient insulation, or over current.
En-8
(6) See the table below for the terminal screw tightening torques.
Tightening torque
[N·m (kgf·cm)]
M4 screw 1.2 to 1.8 (12 to 18)
M5 screw 2.0 to 3.0 (20 to 30)
6.2. Selecting circuit breaker and wiring
CAUTION
Be sure to install a breaker with specifi ed capacity.
Before the electrical working, confi rm electrical standards and regulations in each country,
region, or installing place. Then select appropriate cables and breakers that comply with them.
Decide the diameter of wire referring to below table “Breaker and wiring specifi cations” in
accordance with local and national codes.
Breaker and wiring specifi cations
Breaker
capacity
[A]
Power supply cable Transmission cable*
Conductor size
[mm²]
Conductor size
[mm²]
Max. length
[m]
16 2.5 (Min.) 1.5 (Min.) 75
*: If the transmission wire is longer than 50 m, use the bigger conductor size.
Max. Cable Length: Limit voltage drop to less than 2%. Increase cable gauge if voltage •
drop is 2% or more.
Use confi rmed cable with type 60245 IEC 57.•
Install a circuit breaker with a contact gap of at least 3 mm in all poles nearby the units. •
(Both indoor units and outdoor units)
6.3. Knock out holes for wiring
CAUTION
Be careful not to deform or scratch the panel while opening the knock out holes.
When cables are routed from the unit, a protection sleeve for the conduits can be
inserted at the knock out hole.
If you do not use a wire conduit, be sure to protect the wires to prevent the edge of the
knock out hole from cutting the wires.
It is recommended to apply anti-rust paint to the edge of the knock out hole.
Knock out holes are provided for wiring. (Fig. A)•
Knock out holes are provided 2 each in the same size in front, lateral and rear sides. •
(Fig. B)
Fig. A
Fig. B
Installation method of One-touch bush
Please fi x the One-touch bush (accessory) as shown in the fi gure below.
Front connection Lateral connection Rear connection
One-touch cable bush
(Accessories)
One-touch cable bush
(Accessories)
One-touch cable bush
(Accessories)
(Pipe cover rear)
(Pipe cover front)
Note : Please ensure that the power cable and interconnecting cables are not installed
through the same cable bush hole opening. They must be installed into the two
separate hole openings to prevent damage to the cable.
WARNING
Do not modify power cable, use extension cable or branch wiring. Improper use may
cause electric shock or fi re by poor connection, insuffi cient insulation or over current.
Connect the connector cable securely to the terminal. Check no mechanical force bears
on the cables connected to the terminals. Faulty installation can cause a fi re.
Use crimp-type terminals and tighten the terminal screws to the specifi ed torques,
otherwise, abnormal overheating may be produced and possibly cause serious damage
inside the unit.
Make sure to secure the insulation portion of the connector cable with the cable clamp.
Damaged insulation can cause a short circuit.
Fix cables so that cables do not make contact with the pipes (especially on high
pressure side). Do not make power supply cable and transmission cable come in
contact with valves (Gas).
Never install a power factor improvement condenser. Instead of improving the power
factor, the condenser may overheat.
Be sure to perform the earthing (grounding) work.
Do not connect earthing (grounding) wires to a gas pipe, water pipe, lightning rod or
earthing (grounding) wire for a telephone.
Connection to a gas pipe may cause a fi re or explosion if gas leaks.•
Connection to a water pipe is not an effective earthing (grounding) method if PVC •
pipe is used.
Connection to the earthing (grounding) wire of a telephone or to a lightning rod may •
cause a dangerously abnormal rise in the electrical potential if lightning strikes.
Improper earthing (grounding) work can cause electric shocks.
Securely install the electrical box cover on the unit. An improperly installed service panel
can cause serious accidents such as electric shock or fi re through exposure to dust or
water.
CAUTION
The primary power supply capacity is for the air conditioner itself, and does not include
the concurrent use of other devices.
Do not start operation until the refrigerant is charged completely. The compressor will
fail if it is operated before the refrigerant piping charging is complete.
Transmission cable between indoor unit and outdoor unit is 230 V.
Be sure not to remove thermistor sensor etc. from power wiring and connection wiring.
Compressor may fail if operated while removed.
Start wiring work after closing branch switch and over current breaker.
Use an earth leakage breaker that is capable of handling high frequencies. Because the
outdoor unit is inverter controlled, a high-frequency earth leakage breaker is necessary
to prevent a malfunction of the breaker itself.
When using an earth leakage breaker that has been designed solely for earth (ground)
fault protection, be sure to install a fuse-equipped switch or circuit breaker.
Do not connect the AC power supply to the transmission line terminal board. Improper
wiring can damage the entire system.
Do not use crossover power supply wiring for the outdoor unit.
If the temperature surrounding the breaker is too high, the amperage at which the
breaker cuts out may decrease.
How to connect wiring to the terminal
Caution when wiring cable
When stripping off the coating of a lead wire, always use a special tool such as a wire
stripper. If there is no special tool available, carefully strip the coating with a knife etc.
(1) Use crimp-type terminals with insulating sleeves as shown in the fi gure below to
connect to the terminal block.
(2) Securely clamp the crimp-type terminals to the wires using an appropriate tool so
that the wires do not come loose.
Sleeve
Strip : 10 mm
Crimp-type
terminal
(3) Use the specifi ed wires, connect them securely, and fasten them so that there is no
stress placed on the terminals.
(4) Use an appropriate screwdriver to tighten the terminal screws. Do not use a
screwdriver that is too small, otherwise, the screw heads may be damaged and
prevent the screws from being properly tightened.
(5) Do not tighten the terminal screws too much, otherwise, the screws may break.
Wire
Screw with special washer
Crimp-type terminal
Terminal blocks
Screw with
special washer
Wire
Crimp-type
terminal
En-9
6.4. Wiring method
6.4.1. Connection diagrams
POWER SUPPLY
Indoor unit
side terminal
Outdoor unit
side terminal
N
L3
L2
L1
33
22
11
N(T)(S)(R)
EARTH
(GROUND)
EARTH
(GROUND)
EARTH
(GROUND)
Earthing (Grounding) line
Power line
Control line
6.4.2. Connection cable preparation
Keep the earth (ground) wire longer than the other wires.
Earth (Ground) wire
40 mm
Power supply cable or
Transmission cable
60 mm or more
6.4.3. Wiring procedure
(1) Remove the service panel cover, insulation sheet and connect the wires to the
terminal in accordance with the terminal nameplate. (Fig. A, Fig. B)
Fig. A
Direction of the service
panel removal
Terminal blocks
Service panel
(2) After connecting the wires, use cable clips to secure the wires. (Fig. B)
Connect the wires without applying excessive tension. •
Fig. B
Control box
Terminal blocks
Cable clip
Cable clip
Firmly secure the
cable clips so that the
wire terminals will not
receive external stress.
Use the specifi ed wire
type and connect the
wires securely.
(3) Secure the cables using the cable clips under the terminal blocks, and then secure
the cables using the cable clips attached to the base of the valves.
Cable clip
(4) Be sure to install the insulation sheet after the wiring is complete.
s d
7. PIPE INSTALLATION-2
WARNING
Install the insulated pipes so that they do not touch the compressor.
7.1. Installing insulation
Use an insulation on the refrigerant pipes to prevent condensation and dripping. •
(Fig. A)
Determine the thickness of the insulation material by referring to Table A.•
Table A, Selection of insulation
(for using an insulation material with equal heat transmission rate or below
0.040 W/(m·k))
Relative humidity
[mm (in.)]
Insulation material
Minimum thickness [mm]
70%
or more
75%
or more
80%
or more
85%
or more
Pipe
diameter
6.35 (1/4) 8 10 13 17
9.52 (3/8) 9 11 14 18
12.70 (1/2) 10 12 15 19
15.88 (5/8) 10 12 16 20
19.05 (3/4) 10 13 16 21
If the ambient temperature and relative humidity exceed 32 °C, increase the level of heat
insulation for the refrigerant pipes.
7.2. Filling with putty
WARNING
Fill the piping holes with putty (supplied locally) to avoid any gap (Fig. A). If small
animals such as insects enter the external unit, a short circuit may be caused near
electrical components in the service panel.
If the outdoor unit is installed at a level that is higher than the indoor unit, the water that
has condensed in the 3-way valve of the outdoor unit could travel to the indoor unit.
Therefore, use putty in the space between the pipe and the insulation to prevent the entry
of water.
Fig. A
Insulation
Putty
En-10
8. HOW TO OPERATE DISPLAY UNIT
8.1. Various setting methods
WARNING
Never touch electrical components such as the terminal blocks or reactor except the
switch on the display board. It may cause a serious accident such as electric shock.
CAUTION
Once refrigerant charging is completed, be sure to open the valve prior to performing
the local settings. Otherwise, the compressor may fail.
Discharge any static electricity from your body before touching the push switches. Never
touch any terminal or pattern of any parts on the control board.
The positions of the switches on the outdoor unit control board are shown in the fi gure •
below.
Terminal blocks
Reactors
Various settings can be adjusted by changing DIP switches and push switches on the •
board of the outdoor unit.
DIP switch
Push
switches
LED display
The printed characters for the LED display are shown below.•
SW1 SW2
SW3 SW4 SW5
SW6
(1)
(2) (3)
(4)
(5)
(6)
LED display part
8.2. Description of display
Display lamp
Function or operation method
(1) POWER/MODE Green
Lights on while power on Local setting in
outdoor unit or error code is displayed with
blink.
(2) ERROR Red
Blinks during abnormal air-conditioner
operation.
(3) TEST RUN
(L1)
Orange Lights on during test operation.
(4) PUMP DOWN
(L2)
Orange Lights on during pump down operation.
(5) LOW NOISE MODE
(L3, L4)
Orange
Lights on during “Low noise” function when
local setting is activated.
(Lighting pattern of L3 and L4 indicates
low noise level) B Refer to “9. LOCAL
SETTING”.
(6) PEAK CUT
(L5, L6, L7)
Orange
Lights on during “Peak cut” function when
local setting is activated.
(Lighting pattern of L5, L6 and L7 indicates
peak cut level) B Refer to “9. LOCAL
SETTING”.
Switch
Function or operation method
SW1 DIP switch
For selecting cooling or heating during test
operation.
Positions 2 to 4 of DIP switch are not used.
SW2 Push switch
To switch between “Local setting” and “Error code
display”.
SW3 Push switch
To switch between the individual “Local settings”
and the “Error code displays”.
SW4 Push switch
To fi x the individual “Local settings”, “Test run” and
the “Error code displays”.
SW5 Push switch EXIT
SW6 Push switch To start the pump down operation.
DIP switches 1 to 4 at shipment from the factory are set as follows.•
DIP switch
1234
COOL OFF OFF OFF
s d
9. LOCAL SETTING
CAUTION
Discharge the static electricity from your body before setting up the switches.
Never touch the terminals or the patterns on the parts that are mounted on the board.
9.1. Low noise mode (Local work)
Outdoor unit may be operated with lower noise than normal operation when following
below local work.
Low noise operation is available by installation of an additional commercially available •
timer or contact input from the ON-OFF switch to the CN19 connector (an external
contact input sold separately) on the control board of the outdoor unit.
* Performance may be defi cient depending on outdoor temperature or conditions etc.
< Example of circuit diagram >
Outdoor unit control
board
Remote control
panel
Adapter for
external input
CN19
Power supply
Red
White
Black
1
2
3
1
2
3
SW1
Local purchase
(1) Make a circuit of the above fi gure with
an “Adapter for external input” sold
separately.
(2) Low noise operation can be set up with
the operation of external display portion.
SW1...ON
Level 1
(Shipment condition)
Level 2
SW1...OFF
Normal operation
En-11
9.2. Peak cut mode (Local work)
Effi cient operation while reducing power supply and power consumption with below local
work.
Peak cut function can be effective with contact installation of an additional ON-OFF •
switch to the CN19 connector on the outdoor control board.
< Example of circuit diagram >
Outdoor unit
control board
Adapter for
external input
CN19
Power supply
Red
White
Black
1
2
3
1
2
3
SW2
Remote control
panel
Local purchase
(1) Make a circuit like above fi gure using an
“Adapter external input” sold separately.
(2) Set a restriction for below power
consumption (compared with the rated
consumption). Refer to “8. HOW TO
OPERATE DISPLAY UNIT” for settings.
SW2...ON
Level 1 : 0% (Stop)
Level 2 : 50%
Level 3 : 75%
Level 4 : 100%
(Shipment condition)
SW2...OFF
Normal operation
9.2.1. Setting for peak cut
SW2
SW3 SW4 SW5
LED display part
(1) Switch to “Local setting mode” by pressing MODE switch (SW2) for 3 seconds or
more.
(2) Confi rm POWER/MODE LED blinks 9 times, and press ENTER switch (SW4).
POWER
MODE
ERROR
TEST
RUN
(L1) (L2) (L3) (L4) (L5) (L6) (L7)
PUMP
DOWN
LOW NOISE PEAK CUT
Blinks
(9 times)
Sign “ ” : Lights off
(3) Press SELECT switch (SW3), and adjust LED display as shown below. (Current
setting is displayed)
TEST
RUN
(L1) (L2) (L3) (L4)
PUMP
DOWN
LOW NOISE
Blink
PEAK CUT
MODE
(4) Press ENTER switch (SW4).
TEST
RUN
(L1) (L2) (L3) (L4)
PUMP
DOWN
LOW NOISE
PEAK CUT
MODE
Sign “ ” : Lights on
(5) Press SELECT switch (SW3), and adjust LED display as shown in below fi gure.
PEAK CUT
(L5) (L6) (L7)
Blink
Blink
Blink Blink
Blink
0% of rated input ratio
50% of rated input ratio
75% of rated input ratio
100% of rated input ratio
9.1.1. Setting for low noise
SW2
SW3 SW4 SW5
LED display part
(1) Switch to “Local setting mode” by pressing MODE switch (SW2) for 3 seconds or
more.
(2) Confi rm POWER/MODE LED blinks 9 times, and press ENTER switch (SW4).
POWER
MODE
ERROR
TEST
RUN
(L1) (L2) (L3) (L4) (L5) (L6) (L7)
PUMP
DOWN
LOW NOISE PEAK CUT
Blinks
(9 times)
Sign “ ” : Lights off
(3) Press SELECT switch (SW3), and adjust LED display as shown below. (Current
setting is displayed)
TEST
RUN
(L1) (L2) (L3) (L4)
PUMP
DOWN
LOW NOISE
LOW NOISE
MODE
Blink
(4) Press ENTER switch (SW4).
LOW NOISE
MODE
TEST
RUN
(L1) (L2) (L3) (L4)
PUMP
DOWN
LOW NOISE
Sign “ ” : Lights on
(5) Press SELECT switch (SW3), and adjust LED display as shown in below fi gure.
PEAK CUT
(L5) (L6) (L7)
Blink
Blink
Level 1
Level 2
(6) Press ENTER switch (SW4) and fi x it.
PEAK CUT
(L5) (L6) (L7)
Level 1
Level 2
(7) Return to “Operating status display (Normal operation)” by pressing EXIT switch
(SW5).
In case of missing how many times SELECT and ENTER switch are pressed, restart
from the beginning of operation procedure after returning to “Operation status display
(normal operation)” by pressing the EXIT switch once.
En-12
(3) Press ENTER (TEST RUN) switch for more than 3 seconds.
POWER
MODE
ERROR
TEST
RUN
PUMP
DOWN
LOW NOISE PEAK CUT
(L1) (L2) (L3) (L4) (L5) (L6) (L7)
TEST RUN LED will light on.
If the compressor is operating at starting the test run, the compressor will stop and, •
after a while, the test run will start.
Either of the above LOW NOISE or PEAK CUT LED will light on during the test run if •
local setting function is selected.
(4) Confi rm operating status.
(5) Press ENTER (TEST RUN) switch again.
POWER
MODE
ERROR
TEST
RUN
PUMP
DOWN
LOW NOISE PEAK CUT
(L1) (L2) (L3) (L4) (L5) (L6) (L7)
TEST RUN LED lights off, and TEST RUN stops.
Test run will finish after about 60 minutes automatically. At the same time, TEST RUN •
LED will light off.
Test run may be stopped before operating for 60 minutes if an error occurs after a •
starting test run.
s d
11. PUMP DOWN
WARNING
Never touch electrical components such as the terminal blocks or reactor except the
switch on the display board. It may cause a serious accident such as electric shock.
During the pump-down operation, make sure that the compressor is turned off before
you remove the refrigerant piping. Do not remove the connection pipe while the
compressor is in operation with 2-way or 3-way valve open. This may cause abnormal
pressure in the refrigeration cycle that leads to rupture and even injury.
CAUTION
Perform the pump down operation before disconnecting any refrigerant pipe or electric
cable.
Collect refrigerant from the service port or the 3-way valve if pump down cannot be
performed.
In case of a group control system installation, do not turn the power off pump down is
completed in all outdoor units.
(Group control system installation described in “SPECIAL INSTALLATION METHODS”
in the installation manual of the indoor unit.)
Operate PUMP DOWN switch on the display board in the manner described below.
LED display part
PUMP DOWN
switch
(6) Press ENTER switch (SW4) and fi x it.
PEAK CUT
(L5) (L6) (L7)
0% of rated input ratio
50% of rated input ratio
75% of rated input ratio
100% of rated input ratio
(7) Return to “Operating status display (Normal operation)” by pressing EXIT switch
(SW5).
When pressed number is lost during operation, restart from the beginning of operation
procedure after returning to “Operation status display (normal operation)” by pressing
the EXIT switch once.
s d
10. TEST RUN
CAUTION
Always turn on the power 6 hours prior to the start of the operation in order to protect
the compressor.
10.1. Check items before performing the test run
Make sure to perform the test run.•
Before performing the test run, be sure to check the following points.•
(1) Is gas leaking?
Check connection of each pipe (fl are connection part, brazing part).
(2) Is a breaker installed to the power cable of the outdoor unit?
(3) Has each cable been securely connected to the terminal according to the
specifi cations?
(4) Are the 3-way valves (gas pipes and liquid pipes) of the outdoor units open?
(5) Has the power been supplied to the unit for at least 6 hours?
(6) Has the necessary local setting been done?
(7) Check insulation resistance of 1 MΩ or more using a 500 V mega tester.
If no problems are found with the above items, perform the test run according to “Test •
run method”.
If any problems are found, immediately resolve the problem and re-check the items.•
10.2. Test run method
CAUTION
If the test run is performed for 1 outdoor unit in a group control system installation, the
test run will also be performed for the other units. Therefore, make sure that all of the
units have been installed before starting a test run.
(Group control system installation described in “SPECIAL INSTALLATION METHODS”
in the installation manual of the indoor unit.)
Operate • ENTER (TEST RUN) switch on the display board by the following procedure.
LED display
part
Operation mode
Upper : HEAT
Lower : COOL
ENTER (TEST RUN) switch
10.2.1. Operating procedures for the test run
(1) Check the 3-way valves (both at the liquid side and gas side) are opened.
(2) Set the operation mode to “COOL” or “HEAT”.
POWER
MODE
ERROR
TEST
RUN
PUMP
DOWN
LOW NOISE PEAK CUT
(L1) (L2) (L3) (L4) (L5) (L6) (L7)
In the fi rst test run, be sure to set the operation mode to “COOL”.•
The operation mode cannot be switched between “COOL” and “HEAT” during the test •
run. To switch the operation mode between “COOL” and “HEAT”, stop the test run,
switch the operation mode, and then start the test run again.
En-13
Charging port
Charging port cap
3-way valve
Service hose
Terminal blocks
Service port
Service port cap
Service hose
Reactors
11.1. Preparation for pump down
Confi rm that the power is off, and then open the service panel.
11.2. Pump down procedure
(1) Check the 3-way valves (both at the liquid side and gas side) are opened.
(2) Turn the power on.
POWER
MODE
ERROR
TEST
RUN
PUMP
DOWN
LOW NOISE PEAK CUT
(L1) (L2) (L3) (L4) (L5) (L6) (L7)
(3) Press PUMP DOWN switch for 3 seconds or more after 3 minutes after power on.
ERROR
TEST
RUN
PUMP
DOWN
LOW NOISE PEAK CUT
POWER
MODE
(L1) (L2) (L3) (L4) (L5) (L6) (L7)
LED display lights on as shown in the above fi gure, and the fans and the
compressor start operating.
(4) LED display will change as shown below about 3 minutes after the compressor
starts. Fully close the 3-way valve on the liquid pipe side at this stage.
ERROR
TEST
RUN
PUMP
DOWN
LOW NOISE PEAK CUT
POWER
MODE
(L1) (L2) (L3) (L4) (L5) (L6) (L7)
If the valve on the liquid pipe side is not closed, the pump down cannot be •
performed.
(5) When LED display changes as shown in the below fi gure, close the 3-way valve on
the gas pipe side tightly.
ERROR
TEST
RUN
PUMP
DOWN
LOW NOISE PEAK CUT
POWER
MODE
(L1) (L2) (L3) (L4) (L5) (L6) (L7)
If the valve on the gas pipe side is not closed, refrigerant may fl ow into the piping
after the compressor stops.
Step (5)
Closing direction
Step (4)
Hexagon wrench
Liquid pipe
Gas pipe
Closing direction
(6) LED display changes after 1 minute as shown in the fi gure below.
ERROR
TEST
RUN
PUMP
DOWN
LOW NOISE PEAK CUT
POWER
MODE
(L1) (L2) (L3) (L4) (L5) (L6) (L7)
Fans and compressor stop automatically.
If the pump down is successfully completed (the above LED display is shown), the
outdoor unit remains stopped until the power is turned off.
(7) Turn the power off.
ERROR
TEST
RUN
PUMP
DOWN
LOW NOISE PEAK CUT
POWER
MODE
(L1) (L2) (L3) (L4) (L5) (L6) (L7)
PUMP DOWN is completed.
Notes:
To stop pump down, press the • PUMP DOWN switch again.
To start the pump down again after the compressor is automatically stopped due to an •
error, turn the power off and open the 3-way valves. Wait 3 minutes, turn the power on
and start the pump down again.
When starting the operation after completion of the pump down, turn the power off, •
and then open the 3-way valves. Wait 3 minutes, turn the power on and perform a test
run in the “COOL” operation mode.
12. ERROR CODE DISPLAY
When an error occurs, “short-press” the ENTER switch once. The number of blinks of the
LED indicates the type of error.
12.1. How to check error code
12.1.1. Display when an error occurs
ERROR
TEST
RUN
PUMP
DOWN
LOW NOISE PEAK CUT
POWER
MODE
(L1) (L2) (L3) (L4) (L5) (L6) (L7)
Blinks
(Hi-speed)
Check that the ERROR LED blinks, and then short-press the ENTER switch once.
En-14
12.2. Error code check table
POWER
ERROR
TEST
RUN
PUMP
DOWN
LOW NOISE PEAK CUT
Description
MODE
(L1) (L2) (L3) (L4) (L5) (L6) (L7)
(2) (1) (1) Serial forward transmission error immediately after operation
(2) (1) (1) Serial forward transmission error during operation
(2) (2) (2) Indoor unit capacity error
(2) (5) (15) Indoor unit error
(2) (6) (1) Over voltage
(2) (6) (1) Power supply frequency error
(2) (6) (2) Outdoor unit PCB model information error
(2) (6) (2) PFC communication error
(2) (6) (3) Inverter error
(2) (6) (4) PFC AD detection error
(2) (6) (4) PFC hardware error
(2) (6) (5)
IPM error (Trip terminal L error)
(2) (6) (8) Rush current limiting resister temp rise protection
(2) (7) (1) Discharge temp. sensor error
(2) (7) (2) Compressor temp. sensor error
(2) (7) (3) Heat Ex. middle temp. sensor error
(2) (7) (3) Outdoor unit Heat Ex. liquid temp. sensor error
(2) (7) (4) Outdoor temp. sensor error
(2) (7) (7) Heat sink temp. sensor error
(2) (7) (7) PFC heat sink temp. sensor error
(2) (8) (4) Current sensor 1 error (stoppage permanently)
(2) (8) (6) High pressure switch 1 error
(2) (8) (6) Pressure sensor error
(2) (9) (4) Trip detection (stoppage permanently)
(2) (9) (5)
Compressor motor control error (stoppage permanently)
(2) (9) (5) Compressor motor loss of synchronization (stoppage permanently)
(2) (9) (7) Outdoor unit fan motor 1 error (Duty error)
(2) (9) (8) Outdoor unit fan motor 2 error (Duty error)
(2) (9) (9) 4-way valve error
(2) (10) (1) Discharge temp. 1 error (stoppage permanently)
(2) (10) (3) Compressor 1 temp. error (stoppage permanently)
(2) (10) (5) Low pressure error
Display mode
: Lights on
: Lights off
: Blink (0.5s Lights on / 0.5s Lights off)
( ) : Number of fl ashing
Loading...