High efficiency long-life filter that extends the cleaning
cycle up to 2 times that of the current model is standard.
INDOOR
Slender
OUTDOOR
CEILING TYPE ABU36R
Filter
Double auto swing
VERTICALHORIZONTAL
SWING
Others
Auto Restart
Detachable and Washable Open Panel
SWING
- (03 - 01) -
Page 3
3-2. REMOTE CONTROLLER
3-2-1.
FEATURES
CEILING TYPE ABU36R
WIRELESS REMOTE CONTROLLER
Wireless remote controller is an accessory of all indoor units.
Four kinds of timer setup (ON / OFF / PROGRAM / SLEEP) are possible.
F
Built-in timers
Select from four different timer programs (On/Off/Program/Sleep).
Program timer
The program timer operates the ON and OFF timer once within a 24 hour period.
Four kinds of timers. Easy operation.
Can be used jointly with Wired remote controllers.
Easy to change transmission code (4 patterns) by button operation.
CEILING TYPE ABU36R
Sleep timer
The sleep timer function automatically corrects the temperature thermostat setting according to
the time setting to prevent excessive cooling and heating while sleeping.
Cooling operation/dry operation
When the sleep timer is set, the set temperature
automatically rises 1.8 °F
set temperature can rise up to a maximum of
3.6 °F
(2°C).
60min.
(1°C) every hour. The
Timer setting
1.8 °F(1°C)
3.6 °F
(2°C)
Heating operation
When the sleep timer is set, the set temperature
automatically drops 1.8 °F
The set temperature can drop to a maximum of
7.2 °F
(4°C).
1.8 °F(1°C)
30min.
60min.
90min.
(1°C) every 30 minutes.
3.6 °F(2°C)
5.4 °F
7.2 °F
(3°C)
(4°C)
Timer setting
Simple operation
After code change
Mixed-up
• Code selector switch eliminates unit
being wrongly switched.
(Up to 4 codes can be set.)
ABCD
AB
C
D
•Wide and precise
transmitting range.
1. Press the MASTER CONTROL
button for more than five seconds
to start the code change.
2. Press the (+) or (-) button to
select the desired code.
A B C D
3. Press the MASTER CONTROL
button again to end the code
change.
- (03 - 02) -
Page 4
CEILING TYPE ABU36R
FUNCTIONS
Display
3
2
9
10
1
1
5
START/STOP button
Pressed to start and stop operation
64
AM
F
7
2
Set temp./Set time buttons/Set remote controller
custom code buttons
Sets the indoor temp./Sets the current time and on-off time
/Set R.C. custom code
Note : Specifications are based on the following conditions.
Power source of specifications : 230V
Cooling : Indoor temperature of 80.6°F(27°C)DB/66.2°F(19°C)WB,and outdoor temperature of 95.0°F(35°C)DB/75.2°F(24°C)WB.
Heating : Indoor temperature of 68.0°F(20°C)DB/59.0°F(15°C)WB,and outdoor temperature of 44.6°F(7°C)DB/42.8°F(6°C)WB.
Pipe length : 24ft. 7in.(7.5m),Height difference : 0 ft.(0m) [Outdoor unit - Indoor unit]
- (03 - 04) -
Page 6
3-4. DIMENSIONS
3-4-1. OUTDOOR UNIT
CEILING TYPE ABU36R
MODEL : AOU36R
32-11/16 (830)
Unit : in.(mm)
Top view
35-7/16 (900)
13/16 (21)
(9)
11/32
Front view
3-1/32 (77)
1-7/32
(31)
13 (330)
15-3/4 (400)
15/32
(12)
CEILING TYPE ABU36R
Side view
25-19/32 (650)
Air flow
14-7/8 (370)
MOUNTING POSITION
When there are obstacles at the
back or front sides.
AIR
23-5/8 (600)
or more
3-15/16 (100)
or more
Bottom view
When there are obstacles at the
back, side(s), and top.
3-15/16 (100)
or more
AIR
(
9-27/
Ser
11-13/16 (300)
or more
32 (
v
i
250)
c
e
s
pac
or
mor
e)
e
3-29/32 (99)
(196)
7-23/32
5-25/32 (147)
6-11/16 (170)
When there are obstacles at the
back, side with the installation of
more than one unit.
SIDE VIEW
VERTICAL FLAP : UP
HORIZONTAL FLAP : CENTER
(m)
(ft.)
- (03 - 16) -
Page 18
3-11-2. AIR FLOW
m3/h
1850
m3/h
1660
m3/h
1430
m3/h
3600
1100
1000
850
850
Indoor unit
Outdoor unit
HIGH
MED
LOW
HIGH
FAN SPEED
NUMBER OF
ROTATIONS
(r.p.m)
AIR FLOW
MODELS : ABU36R / AOU36R
CEILING TYPE ABU36R
l/s514
CFM1089
l/s461
CEILING TYPE ABU36R
CFM977
l/s397
CFM842
l/s1000
CFM2119
- (03 - 17) -
Page 19
3-11-3. FRESH AIR
FRESH AIR CHARACTERISTIC
CEILING TYPE ABU36R
0.39
0.2
(Pa)
98
49
10
8
6
4
2
13/32
5/16
1/4
5/32
3/32
(in.WG)(mmAq) (in.Ag)
INTAKE DUCT STATIC PRESSURE
CEILING TYPE ABU36R
3
(m /min)
3
(ft /min)
01234567
3571106141177212247
FRESH AIR FLOW (m /min)
3
0
0
- (03 - 18) -
Page 20
3-12. NOISE LEVEL CURVE
3-12-1. OUTDOOR UNIT
CEILING TYPE ABU36R
COOLING
MODEL : AOU36R
80
70
60
50
40
30
20
Octave band sound pressure level, dB:(0dB=0.0002µbar)
10
NC-65
NC-60
NC-55
NC-50
NC-45
NC-40
NC-35
NC-30
NC-25
NC-20
NC-15
HEATING
MODEL : AOU36R
80
70
60
50
40
30
20
Octave band sound pressure level, dB:(0dB=0.0002µbar)
10
NC-65
NC-60
NC-55
NC-50
NC-45
NC-40
NC-35
NC-30
NC-25
NC-20
NC-15
CEILING TYPE ABU36R
0
631 252505001,0002,0004,0008,000
Octave band center frequency,Hz
0
631 252505001,0002,0004,0008,000
Octave band center frequency,Hz
- (03 - 19) -
Page 21
SOUND LEVEL CHECK POINT
CEILING TYPE ABU36R
3ft. 3-3/8in. (1m)
CEILING TYPE ABU36R
- (03 - 20) -
Page 22
3-12-2. INDOOR UNIT
HIGH
LOW
HIGH
LOW
CEILING TYPE ABU36R
COOLING
MODEL : ABU36R
80
70
60
50
40
30
20
Octave band sound pressure level, dB:(0dB=0.0002µbar)
10
NC-65
NC-60
NC-55
NC-50
NC-45
NC-40
NC-35
NC-30
NC-25
NC-20
NC-15
HEATING
MODEL : ABU36R
80
70
60
50
40
30
20
Octave band sound pressure level, dB:(0dB=0.0002µbar)
10
NC-65
NC-60
NC-55
NC-50
NC-45
NC-40
NC-35
NC-30
NC-25
NC-20
NC-15
CEILING TYPE ABU36R
0
631 252505001,0002,0004,0008,000
Octave band center frequency,Hz
0
631 252505001,0002,0004,0008,000
Octave band center frequency,Hz
- (03 - 21) -
Page 23
SOUND LEVEL CHECK POINT
UNDER CEILING
3ft. 3-3/8in.(1m)
3ft. 3-3/8in. (1m)
MIC
CEILING TYPE ABU36R
CEILING TYPE ABU36R
- (03 - 22) -
Page 24
3-13. ELECTRIC CHARACTERISTICS
Main Fuse (Circuit breaker)
Current
60
ABU36R
AOU36R
10
Rated Value
Mode
*1) Wiring Spec.
10
30
Max Operating Current
Starting Current
0.59
0.14
0.63
Model Name
Outdoor Fan Motor
0.13
95
Indoor Fan Motor
Power Supply
230
Indoor unit
Outdoor unit
MODELS : ABU36R / AOU36R
VoltageV
FrequencyHz
CurrentA18.315.3
InputkW4.223.50
CoolingHeating
A18.818.8
CEILING TYPE ABU36R
A
A
Power CableAWG
*2)Limited wiring lengthft.
InputkW
Full Load Amp.A
InputkW
Full Load Amp.A
*1) Wiring Spec. : Selected Sample
(Selected based on Japan Electrotechnical Standard and Codes Committee E0005)
*2) Limited Wiring length : This is the wiring length in case voltage descent is less than 2%.
When the wiring length becomes long, please select the wiring of a more
larger diameter.
CEILING TYPE ABU36R
- (03 - 23) -
Page 25
3-14. SAFETY DEVICE
PROTECTION FORM
OFF : 609±15 psi
ON : 464±22 psi
OFF : 4.2±0.1MPa
ON : 3.2±0.15MPa
OFF : 248±9°F
ON : 176±9°F
OFF : 120±5°C
ON : 80±5°C
OFF : 266±9°F
ON : 176±9°F
OFF : 130±5°C
ON : 80±5°C
5A 250V
AOU36R
3.15A 250V
FUSE ON MAIN PCB
CURRENT FUSE
PROTECTION FORM
ABU36R
3.15A 250V
OUTDOOR UNIT
CEILING TYPE ABU36R
FAN MOTOR PROTECTIONTHERMAL PROTECTOR
HIGH PRESSURE PROTECTION PRESSURE SWITCH
DISCHARGE THERMISTORTHERMAL PROTECTOR
COMPRESSOR THERMISTORTHERMAL PROTECTOR
212
+27
-18
°F
100 °C
INDOOR UNIT
PCB FUSECURRENT FUSE
FAN MOTOR PROTECTIONTHERMAL PROTECTOR248±9°F 120±5°C
+15
-10
CEILING TYPE ABU36R
- (03 - 24) -
Page 26
3-15. FUNCTION SETTING
Auto restart validity/invalidity
Room temperature correct coefficient
Room temperature correct coefficient
Forbidden
Indoor unit number setting
Forbidden
Remote control unit signal code
Ceiling height setting
INDOOR UNIT
DIP SW
3
1
JM3
Jumper Wire
2
3
JM1
JM2
Rotary SW
SW 2
SW 1
SW 4
1
2
3-15-1. INDOOR UNIT
CEILING TYPE ABU36R
CEILING TYPE ABU36R
SWITCH POSITION
Indoor unit control circuit board
- (03 - 25) -
Page 27
3-15-2. SWITCH FUNCTION (INDOOR UNIT)
SW 1-1
SW state
OFF
Invalidity
ON
Validity
0 degF
0 degF
0 degF
cooling
-3.6degF
SW 1-2
SW 1-3
0 degF
heating
dry
-3.6degF
-3.6degF
ONONON
OFF
OFF
+3.6degF
-3.6degF
OFF
SW state
-3.6degF
OFF
ON
0 degF
+7.2degF
3
OFF
-
ON
Normal
High ceiling 1
High ceiling 2
Low ceiling
-ONON-OFF
-
ON
OFF
OFF
Ceiling height ft.(m)
DIP - SW4
1
2
DIP SWITCH SETTING
SW1-1. Auto restart setting
Auto restart function can be selected by turning this switch ON/OFF.
AUTO RESTART SETTING
(Factory setting)
CEILING TYPE ABU36R
SW1-2, 1-3. Room temperature correct coefficient of heating.
Decide the heating temperature correct coefficient value of heating.
TEMPERATURE CORRECTION
(Factory setting)
When used for Floor console type
SW4-1. REMOTE CONTROLLER SETTING
(Factory setting)
SW 4-1
OFF
ON
Wireless Remote Controller
Wired Remote Controller (option)
SW state
CEILING TYPE ABU36R
SW4-2, 4-3. Ceiling height setting
8ft. 2-7/16in. to 9ft. 10-1/8in. (2.5 to 3.0)
9ft. 10-1/8in. to 11ft. 5-25/32in. (3.0 to 3.5)
More than 11ft. 5-25/32in. (3.5)
Less than 8ft. 2-7/16in. (2.5)
If the setting for a low ceiling is selected, the capacity of the air
conditioner decreases slightly.
- (03 - 26) -
(Factory setting)
Page 28
BCD
Disconnect
Disconnect
Disconnect
Disconnect
connect
connect
JM3
Remote control unit
signal code
connect
connect
A
JM2
Jumper wire
ROTARY SWITCH SETTING
0
Single
1 - 15
Indoor unit address
SW 2
SW state
(This function operates only when optional wired remote controller is used.)
This switch can be used when group control system.
Set the indoor unit address in the 0,1,-,15 order.
(Factory setting)
CEILING TYPE ABU36R
JUMPER WIRE SETTING
JM 1, 2, 3 setting
(Factory setting)
CEILING TYPE ABU36R
- (03 - 27) -
Page 29
3-16. OPTIONAL PARTS
3-16-1. WIRED REMOTE CONTROLLER
FEATURES
Various timer setup (ON / OFF / WEEKLY) are possible.
CEILING TYPE ABU36R
SUMOTUWETH FR SA
AM
7
3126 9
F
15 18 21
High performance and compact size
Equipped with weekly timer as standard function.
(2 times Start / Stop per day for a week)
When setting up a timer, operation mode and a temperature
setup can be changed.
When a failure occurs,the error code is displayed. (Maximum of 16)
Error indication.(A maximum of 16 error histories are memorizable.)
Easy installation with a slim shape with no boldge in the back.
Built in room temperature sensor.
CEILING TYPE ABU36R
Three functions are combined in
one unit.
Wired
remote
controller
Built-in timers
Possible to set ON/OFF time to operate twice each day
of the week.
SUMOTUWETH FR SA
7
PM
3126 9
15 18 21
Setup screen example
[Set to Wednesday: AM8:00 to PM8:00,75 °F(24 °C)]
0 3 6 9 12 15 18 21
timeO'clocktimeO'clock
12 3 6 9 12 3 6 9
At "Weekly timer" + "Set back timer" setup
Easy-to-understand time bar display
SUMOTUWETH FR SA
AM
7
3126 9
F
15 18 21
75°F (24°C)
AMPM
75°F 82°F 75°F
(24°C 28°C 24°C)
Weekly
timer
Setback
timer
Setback timerWeekly timer
Possible to set temperature for two time spans and
for each day of the week.
SUMOTUWETH FR SA
Screen
after setup
Setup screen example
[Set from Sunday to Saturday: PM12:00 to PM3:00, 82°F(28 °C)]
0 3 6 9 12 15 18 21
12 3 6 9 12 3 6 9
75°F (24°C)
0 3 6 9 12 15 18 21
timeO'clock
12 3 6 9 12 3 6 9
AMPM
PM
3126 9
15 18 21
82°F (28°C)
AMPM
82°F (28°C)
F
Easy-to-understand operationSimple installation
Components are compatible with standard
switch boxes. Flat back construction allows
equipment to be installed wherever it is
needed.
Timer
area
[
Variable timer control
]
The operation/display sections are zoned according to time and operation, enabling variable programming to match application.
Operation
area
European
switch box
- (03 - 28) -
JIS box
Page 30
CEILING TYPE ABU36R
FUNCTIONS
Display
2
7
8
9
10
11
12
Display panel
SET BACK
16
SUMOTUWETH FR
AM
PM
369
SUMOTUWETH FR
AM
PM
369
CLOCK ADJUST
DELETESET
12 15 18 21
12 15 18 21
DAY
DAY OFF
1
START/STOP button
Pressed to start and stop operation.
2
Set Temperature button
SA
F
15
1
3
ENERGY
SAVE
THERMO
SENSOR
4
6
5
Selects the setting temperature.
3
Master control button
Selects the operating mode(AUTO, HEAT, FAN, COOL, DRY).
4
Fan control button
Selects the fan speed (AUTO, LOW, MED, HIGH).
5
Energy save button
Turns the energy efficient mode on and off.
13
14
6
Thermo sensor button
Selects whether the room temperature is detected at the
CEILING TYPE ABU36R
indoor unit (remote sensor) or the remote controller.
7
Timer mode (CLOCK ADJUST) button
Selects the timer mode (OFF TIMER, ON TIMER, WEEKLY TIMER)
Set the current time.
8
Day (DAY OFF) button
Temporarily cancels of one day timer.
17
1819 20
SA
F
9
Set back button
pressed select the set back timer.
10
Set time button
Pessed to select the set back timer.
Delete button
2122 2324 25
11
The schedule of a weekly timer is deleted.
12
Set button
Sets the date, hour, minute and on-off time.
13
Horizontal air flow direction and swing button
Push for two seconds to change the swing mode.
14
Vertical air flow direction and swing button
Push for two seconds to change the swing mode
15
Operation lamp
Lights during operation and when the timer is on.
16
Timer and clock display
17
Operation mode display
18
Fan speed display
Central control display
19
20
Temperature display
21
Stand by display
Indicates during defrosting operation.
22
Vertical swing display
23
Horizontal swing display
24
Energy save display
25
SPECIFICATION
Thermo sensor display
SIZE [(H x W x D in.) mm]4-23/32 x 4-23/32 x 43/64 (120 x 120 x 17)
WEIGHT oz.( g )5-21/32 (160)
CABLE LENGTH ft.( m )
POWER( V )
33 (10)
12
- (03 - 29) -
Page 31
3-16-2. WIRED REMOTE CONTROLLER CIRCUIT BOARD
Wired remote controller
1
Dual remote controller setting
2
Group control setting
DIP SW
3
4
Model setting
Auto changeover setting
5
6
Memory backup setting
CEILING TYPE ABU36R
SWITCH POSITION
Wired remote controller
Front case (back side)
DIP Switch
OFF
CEILING TYPE ABU36R
ON
1
2
3
4
5
6
ON
- (03 - 30) -
Page 32
3-16-3. WIRED REMOTE CONTROLLER
DIP SWITCH SETTING
1. SW setting
1-1 Dual remote controller setting
Set the remote controller DIP switch No.1 and 2 according to the following table.
(Factory setting)
Number of
remote
controller
1 (Normal)
2 (Dual)
CEILING TYPE ABU36R
1-2 Group control setting
Number of indoor unit connection (One/Multiple)
This is switched according to the number of connected indoor units.
DIP-SW
No.3
OFF
Master unitSlave unit
DIP-SW
No.1
DIP-SW
No.2
ON
OFF
(Factory setting)
Number of indoor unit
One unit connection
OFF
OFF
DIP-SW
No.1
ONON
DIP-SW
No.2
CEILING TYPE ABU36R
ONMultiple unit connection
1-3 Model setting
The system type of the outdoor unit can be selected by setting up DIP switch No.4 as follows.
(Factory setting)
DIP-SW
No.4
OFF
ONCooling only model
Heat Pump model
Model
1-4 Auto changeover setting
Selecting auto changeover validity / invalidity.
(Factory setting)
DIP-SW
No.5
OFF
ONValidity
Auto changeover
Invalidity
1-5 Memory backup setting
Set to ON to use batteries for the memory backup.If batteries are not used,
all of the settings stored in memory will be deleted if there is a power failure.
This function is wired remotecontroll only.
(Factory setting)
DIP-SW
No.6
OFF
ONValidity
Memory backup
Invalidity
- (03 - 31) -
Page 33
3-16-4. OPTIONAL PARTS
Drain water riser kit (UTR-DPB241)
Optional drain lift-up mechanism allows more flexible installation.
ROUND FLANGE (UTD - RF204)
CEILING TYPE ABU36R
Round flange is used when the fresh air duct is installed.
Ø8-1/16(205)
Ø7-11/16(195)
CEILING TYPE ABU36R
UNIT : in.(mm)
)
5
3
2
(
4
/
1
-
9
Ø
Ø
8
-
2
7
/
3
2
(
2
2
5
)
Ø3-11/32
(85)
Round flange
- (03 - 32) -
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.