Page 1
22 inch Color LCD MONITOR
Page 2
Table of Contents
EMC COMPLIANCE
1
IMPORTANT PRECAUTIONS
2
1. Introduction
1.1. General
4
1.2. Features
4
1.3. Packing List
4
2. Installation
2.1. Connection of signal cable
5
2.2. Connection of power cord
5
2.3. Connection of Audio cable
5
2.4. Power on
6
2.5. Self-inspection
6
2.6. Image Adjustment
6
3. Operation
3.1. OSD button
7
3.2. OSD menu and operation menu introduction
9
3.3. Safeguard
12
3.4. Power management system
12
3.5. Setting of display mode
13
4. Technical specification
4.1 22" TFT-LCD monitor specification
14
4.2 Pin assignment of signal cable
15
4.1 Visual Inspection
15
5. Trouble Shooting
16
Page 3
EMC COMPLIANCE IMPORTANT PRECAUTIONS
EMC COMPLIANCE
This device has been tested and found to comply with the standards for a class
B digital device, pursuant to Part 15 of FCC Rules. Those standards are designed
to provide reasonable protection against harmful interference in a residential
installation. This device generates and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
If this device does cause harmful interference to radio or television reception,
which can be determined by turning the device off and on, user is encouraged to
try to correct the interference by one or more of the following measures:
---Reorient or relocate the receiving antenna
---Increase the separation between the device and receiver
---Plug the device into a wall outlet different from that connected to the receiver.
---Consult the dealer or an experienced radio/TV technician for help.
CAUTION: any change or modification not expressly illustrated in this
manual may void the warranty.
NOTE: any unshielded cable is not allowed to
be used in the device!
IMPORTANT PRECAUTIONS
WARNINGS:
1. Before using this device, please read all the instructions in this manual carefully.
2. Please keep the manual carefully for future reference.
3. Unplug this device from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp or wet cloth to clean. Please use LCD
screen detergent for cleaning if it is still dirty.
4. Do not use the parts not recommended by the manufacturer, otherwise it may
cause a hazard.
5. When unplugging the power cord of the monitor or adapter, please hold the plug
with your hand; do not pull the cord directly.
6. Do not place any object on the power cord. Do not trample it either.
7. Do not use the device near water sources, e.g. bathtub, basin, kitchen sink, or
washing machine. Do not place the device on a wet floor, or near a swimming
pool etc. Do not touch the screen with your fingers or other hard objects.
8. Slots and openings on the housing and its back or bottom are provided for
ventilation. To ensure reliable operation of the components and to protect them
from overheating, these openings must not be blocked or covered placing the
device on a bed, sofa, rug, or other similar surface. The device should never be
placed near or over a radiator or heater and should not be placed in a built-in
installation unless proper ventilation is provided.
9. Make sure that the device is at least 5cm distance from the wall or other objects
around when it is in use.
10. The power supply must respond to that stated on the rating plate. If you have
any query about the power supply, please refer to the dealer or local power
supply provider.
11. As a safeguard measure, the monitor or adapter is equipped with a power cord
with three-terminal plug, the third terminal is grounded. If the plug cannot be
inserted into the outlet, please contact an electrical technician for replacing the
original outlet while keeping the safeguard measure in effect.
12. Ensure that the power socket and cord in use are able to take the sum of the
rated currency of all the products.
13. Do not put the device at the place where user is subject to mal-operation.
page 1
page 2
Page 4
IMPORTANT PRECAUTIONS INTRODUCTION
14. Observe all the warnings and instructions described in the manual.
15. Do not overload the power outlet or use any extension cord, otherwise it may
cause fire or electric shock.
16. Do not attempt to repair this device yourself since opening or removing covers
may expose you to dangerous voltage or other hazards. Refer servicing to
qualified service personnel.
17. Unplug this monitor or AC adaptor from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or worn.
b. If the device has been dropped or its housing has been damaged.
c. When the performance of the device deteriorates distinctly.
18. The power cord is the main facility to turn on/off the device; unplug it if the
device is not used for a long period of time.
19. Store the device at a place of good ventilation; avoid strong sunlight, high
temperature or humidity.
20. Store the device at a place at -20°C~55
°C
room temperature. Otherwise, it
may cause permanent damage.
1. Introduction
1.1 General
Thank you for purchasing the latest model of LCD monitor, with advantages of
high display performance and light weight etc, meanwhile with the power saving
and no-radiation features, the latest LCD will bring you comfortable, safe and
environmental-protection brand-new visual experience.
Your purchase and use of this product is highly appreciated!
1.2 Features
--- High performance intelligent multi-frequency scanning, use active matrix Thin
film transistor liquid crystal display (TFT).
--- Micro Computer digital technology control, no radiation, no glare, built-in
multimedia speaker system (option).
--- Built-in AV signal connection terminal and 8 terminal (option).
--- Comply with VESA DPMS International Power Saving Regulation.
--- Support DDC 1/2B and Windows PNP Plug & Play.
--- Microprocessor based with OSD (On Screen Display) control, be able to
adjust the image to optimum.
--- Built-in hoisting hole complying with International Standard (VESA), which is
able to hang the display on the wall.
1.3 Packing list
Please make sure the following items are included with your LCD display before
installation:
--- A LCD monitor (with pedestal)
--- A VGA signal cable, DVI-D signal cable (option)
--- An audio cable (option)
--- A power cord
--- A AC adapter
--- User's manual, qualification and warranty cards
If any of there items are missing, please contact with your dealer for
technical support and customer service.
NOTE: be sure to save original box and all packing material
for transport in future if the display need.
page 3 page 4
Page 5
INSTALLATION INSTALLATION
2. Installation
2.4 Power on
Turn on the monitor and computer, and then indicator will light green (or blue)
when the screen is under normal condition. Please check to see if there is any
wrong with the connection of video signal cable if the indicator lights red.
2.5 Self-inspection
If the monitor inspects there is no horizontal and vertical signal, it will prompt to
check the video input, please refer to the illustration below, and the monitor will
enter into power saving mode after several
5
Installation hole for wall hanging
1
VGA signal input jack
2
DVI signal input jack
3
Power jack
4
Audio input jack
seconds, the indicator will light red. The
screen will restore to normal display once
receiving video signal.
2.6 Image Adjustment
NO SIGNAL
Please adjust the image according to your need; please refer to the "Operation"
in Section Three.
1
VGA signal input: connect to computer VGA signal output jack
2
DVI signal input: connect to computer DVI signal output jack
3
Power jack: connect to adaptor DC output jack
4
Audio input: connect to computer sound card audio output jack
2.1 Connection of signal cable
Before connecting your monitor and PC with signal cable, please turn off your
monitor and computer. And then insert one end of the signal cable into the VGA
or DVI jack on your computer, and lock it with two fixed screw for ensured
grounding. Finally, please insert another end of signal cable to the VGA or DVI
signal input jack of monitor and lock it with fixed screw.
2.2 Connection of power cord
First, insert one end of power cord into the input jack of adaptor, and another end
into power outlet, then insert the output terminal of adaptor into the power input
jack of monitor.
2.3 Connection of Audio cable
Please insert one end of audio cable into the sound card audio output terminal on
your computer, another end into the audio input terminal of monitor.
page 5 page 6
Page 6
AUTO MENU
AUTO MENU
OPERATION OPERATION
3. Operation
3.1 OSD button
4 3 6 5 1 2
(3) Menu Button
Activate OSD, enter sub menu, select items, and confirm selection.
(4) AUTO Button
Automatically set the screen display to optimum.
(5) Button
Select and adjust the OSD items (Increase the value)
(6) Button
Select and adjust the OSD items (Decrease the value)
(7) VOL-
Select VOL-Volume Decrease (Decrease the value)
(8) VOL+
Select VOL+ Volume Increase (Increase the value)
4 3 2 1 6 5
AUTO
MENU
4 3 6 5 1 2
MENU
VOL- VOL+ AUTO
3 6 5 2 1 7 8 4
(1) Power Switch ( )
Digital control light-touch switch, used for turning on or off monitor power.
(2) Power Indicator
When the monitor is under normal working condition, the indicator will light green
(or blue); if the monitor is under saving mode, the indicator will light red or off. And
the indicator will turn off under the power off mode. (When the power indicator
turns off, it means that the monitor is under off mode, but please pay attention that
the adaptor is still in charge, so please disconnect the adaptor when the monitor is
not used for the purpose of safety.)
page 7
page 8
Page 7
H-position adjustment:
use or to adjust the horizontal position to optimum.
V-position adjustment: use or to adjust the vertical position to optimum.
OPERATION OPERATION
3.2 OSD menu and operation menu introduction
Press the MENU to call out the OSD menu (main menu), please see the
illustration as below:
With or to select the desired items, and then press the MENU button for
adjustment, with / button to adjust the display items to optimum, press again
for confirmation and exit adjustment.
Brightness adjust menu
Brightness: use or to adjust the brightness to optimum.
Contrast: use or to adjust the contrast to optimum..
Return: back to previous menu.
Color adjustment menu
Red/Green/Blue color adjustment: use or to adjust the value of red,
green and blue to change the image color so as to meet your needs.
Color temperature: use or to select desired color temperature (9300k,
6500k, USER)
Color adjustment:
it can be adjusted if under shadow mode. If you are not
satisfied with the color temperature set by manufacturer, you may set the color
temperature to USER mode; it will light red at this time. When enter adjust
menu, please use or to adjust R, G, B to change the color of image.
Return: back to previous menu.
Re turn
Bri ght ness 50
Co ntra st 50
USE R
1280 X102 4@75H z
Ret urn
Aut o Col or
Col or
Red 50
Gre en 50
Blu e 50
USE R 128 0X102 4@75 Hz
Image adjustment menu
MENU
S e l e c t
- +
M o v e
MENU
S e l e c t
- +
M o v e
Auto-adjust: with this button to adjust the display to optimum
Image position level/clock set: use or to adjust the image position level
to optimum.
Phase adjustment: use or to adjust the focus and definition to optimum.
Return: back to previous menu.
Audio adjustment menu
Volume: use or to adjust the volume to optimum (option)
Mute: use or to select Mute/Sound.
Return: back to previous menu.
Ret urn
Auto Ad just
H Pos ition 43
V Pos ition 42
Clo ck 50
Phas e 74
Ret urn
Mut e
Vol ume 50
USE R 128 0X102 4@75 Hz
USE R
1280 X1024 @75H z
MENU
S e l e c t
- +
M o v e
MENU
S e l e c t
- +
M o v e
page 9 page 10
Page 8
Mod e Res ol ut ion
Hor iz on tal(KH z)
Vert ic al( Hz)
1
640x400
31.469
70.087
2
640x480
31.469
59.940
3
640x480
37.861
72.809
4
640x480
37.500
75.000
5
720x400
31.469
70.087
6
800x600
35.156
56.250
7
800x600
37.879
60.317
8
800x600
48.077
72.188
9
800x600
46.875
75.000
10
1024x768
48.363
60.004
11
1024x768
56.476
70.069
12
1024x768
58.038
71.918
13
1024x768
60.023
75.029
14
1024x768
48.019
60.000
15
1024x768
47.700
60.000
16
1152x864
67.500
75.000
17
1280x800
49.702
74.900
18
1280x800
62.795
60.000
19
1280x960
60.000
60.000
OPERATION OPERATION
System setting menu
Language: use or to select desired language.
Menu display time: use or to select the desired time for menu display.
Saving time: use or to select desired time for display so as to meet your
requirement.
Reset: reset all the set value to factory setting.
3.3 Safeguard
When the video signal of your computer exceeds the frequency range of monitor
(refer to product specification), the micro-computer of monitor will turn off the sync
signal of horizontal and vertical for the purpose of monitor protection, please refer
to the illustration below. The monitor will enter saving mode after few seconds,
and the power indicator will light red. Please
Return: back to previous menu.
set the output frequency of your computer
within the acceptable range of monitor so that
the monitor can work normally.
OUT OF RANGE
Ret urn
La nguag e Eng lish
OSD Timeo ut 60
Pow er Sa ve 8
Res et
4 : 3 OFF
USE R 1280 X1024 @75Hz
3.4 Setting of display mode
With standard VESA and DDC function, the monitor will scan frequency, output
power, performance etc and transfer to PC after turning on when you use the
video card with VESA DDC1/2B function. And it will identify the connection mode
of display and select the proper resolution.
The preset mode before leaving factory is as below:
MENU
S e l e c t
- +
M o v e
Display mode:when setting OFF,it is display mode,whensettingON,
it will be 4:3 display mode
Exit and signal resource selection menu
Select terminal input: select input terminal for signal input (option)
Exit: exit OSD menu
Exit
VGA
√
DVI
MENU
S e l e c t
USE R 128 0X102 4@75 Hz
- +
M o v e
Note: Hot Key of volume, brightness, contrast
Without OSD mode, your may press " " button to call volume adjustment directly,
when the volume menu is not exit, please press "MENU" to call brightness and
contrast adjustment, you may use " / " to adjust it to optimum.
page 11
page 12
Page 9
20
1280x1024
63.980
60.000
21
1280x1024
79.976
75.025
22
1440x900
55.935
60.000
23
1440x900
70.635
75.000
24
1680x1050
65.290
60.000
25
1600x1200
75.000
60.000
26
22"
Screen model
22" Active Matrix TFT LCD
Dot pitch (H x V )
0.27675x0.27675mm
Surface treatment
Anti-glare, 3H
Active display area (H x V) 464.94mm (H) x290.5875mm (V)
Max. Resolution
1680x1050
Contrast
1000 : 1 (Typ)
Brightness
300cd/m
2
(Typ)
Responsive time
5ms (Typ)
Display color
16.7M (6bits + Hi-FRC)
Visible angle left/right
up/down
+70°~ -70°or +80°~ -80°
+75°~ -75°or +85°~ -85°
Input signal video signal
synchronization
RGB simulation 0.7V p-p
TTL positive or negative polarity
Display format
VGA, SVGA, XGA,WSXGA+
Audio input terminal
RCA terminal (x2) (option)
Signal connector
15 pin D-sub or DVI-D (Option)
Panel button
Power switch, LED indicator, OSD menu, +/- button, auto setting
OSD Function
Contrast, brightness, auto adjustment, image level, phase,
image h-position, image v-position, OSD h-position,
OSD v-position, color temperature, RGB, language
Adaptor AC input
100V~240V 50/60Hz
Adaptor DC output
12V 5A
Max. Power consumption 50W
Working environment
Temperature
Humidity
0℃~
℃
20%~80%
Storage environment
Temperature
Humidity
-20℃~
℃
20%~80%
Packing dimension (LxWxH) 585X200X502mm
Weight (Kg)
N.W: 5.5, G.W: 7.5
OPERATION TECHNICAL SPECIFICATION
4.1 22" "TFT-LCD monitor specification
Note:
22" LCD Monitor is applied to items 1-25, recommended mode;
3.5 Power management system
This monitor complies with EPA Energy Star, and is compatible with VESA DPMS
standard; the saving mode is shown as below:
Mode
Power Indicator Power Consumption 22"
Normal
Green or blue
≤
50W
Standby/Saving Red or turn off
≤
5W
Power Off
Turn off
≤
3W
Note: all technical specifications in this manual and on the packing are subject to change
without prior notice!
page 13 page 14
Page 10
Pin Signal(D-sub) Pin Signal(D-sub)
1
Red
9
DDC Power
2
Green
10
Ground
3
Blue
11
Ground
4
Ground
12 SDA(FOR DDC)
5
Test Cont
13
H. sync
6
Red Ground 14
V. Sync
7 Green Ground 15 SCL(FOR DDC)
8 Blue Ground
TECHNICAL SPECIFICATION
TROUBLESHOOTING
4.2 Pin assignment of signal cable
5. Troubleshooting
4.3 Visual Inspection
1
5
6 10
11
15
If your monitor cannot work normally, please refer to the follow methods for
common problems quickly, if you need assistance; please call the dealer
where you purchased the Monitor.
A. There is no Screen Image/LED no light
Please check to see whether the power cord is securely connect to the monitor
and wall outlet, and whether the display is in power saving mode.
B. There is no Screen Image/LED light red
Please to see whether the display card of PC is loosed, and check the connection
between signal cables and display.
C. The display is not clear or the image is too large or too small
Enter the OSD image adjustment menu, and then select "Auto Adjust" to make
the display to adjust automatically to optimum.
D. The image is too light or too dark
Enter the OSD brightness adjustment menu, and then select the " " to adjust
the brightness and contrast to optimum.
E.. The screen is overheated
Please keep at least 5cm around the display for ventilation, and do not place
anything onto the monitor.
F. Dark display after power on/ facula
This is normal. Due to the temperature difference, the backlight will not give out
light equably at the beginning of powering on, but the backlight lamp will come to
normal work after 20 minutes, the darkness and facula will disappear at this time. G.
The image is distorted to flash and shake
Check the set of computer and choose the proper resolution, then readjust and
renovate the resolution.
H. The color is abnormal
Check the connection of signal cable, if there is any curved or broken pin, please
Even the normal pixels on the LCD screen reach 99.99% or higher,
there may be 0.01% or less pixels showing dark or light while
displaying.
replace it; Enter the OSD color adjustment menu to set the display color to the
optimum.
page 15 page 16
Loading...