IMAGE™ ONE
BLUETOOTH®
OWNER’S MANUAL
IMPORTANT SAFETY INFORMATION
1) READ these instructions.
2) KEEP these instructions.
3) HEED all warnings.
4) FOLLOW all instructions.
5) DO NOT use this apparatus near water.
6) CLEAN ONLY with dry cloth.
7) DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9) DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wider blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) ONLY USE attachments/accessories specified by the manufacturer.
12) UNPLUG this apparatus during lightning storms or when unused for long periods of time.
13) REFER all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
14) DO NOT expose this apparatus to dripping or splashing and ensure that no objects filled with
liquids, such as vases, are placed on the apparatus.
15) To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord
plug from the AC receptacle.
16) The mains plug of the power supply cord shall remain readily operable.
17) DO NOT overload wall outlets or extension cords beyond their rated capacity as this can cause
electric shock or fire.
18) NEVER operate a motor vehicle while listening to or wearing your headphones. Not only dangerous, it is illegal in many places.
19) NEVER operate heavy machinery while listening to or wearing your headphones.
20) We don’t recommend you use the headphones while riding a bicycle, running, or walking in
heavy traffic areas.
WARNING:
Except in case of emergency, Klipsch recommends you do not use these headphones or headsets
(headphones plus microphone) as aviation communication equipment as they are not engineered
for many environmental conditions common in commercial or non-commercial aircraft (including,
but not limited to: altitude, temperature, noise conditions, unpressurized aircraft, ect) resulting in
possible interference to critical communications
WARNING: To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture.
WARNING: No user serviceable parts inside.
WARNING: No naked flame sources – such as candles – should be placed on the product.
WARNING: This product’s operating temperature range is 32-115°F (0-45°C). Avoid exposure to
extreme heat or cold.
THIS PRODUCT CONTAINS A LITHIUM-POLYMER BATTERY PACK.
IF MISUSED OR ABUSED THIS CAN RESULT IN:
Smoke / gas hazard
Heat hazard
Fire hazard
Explosion hazard
WARNING: Batteries (battery pack or batteries installed) shall not be exposed to excessive heat
such as sunshine, fire or the like.
WARNING: Risk of leakage. Do not handle leaking or damaged Lithium batteries.
WARNING: Do not place batteries in mouth or ingest. Keep out of reach of children and pets.
Please dispose of any used batteries properly following any local regulations. Do not incinerate.
WARNING: Danger of explosion if battery is incorrectly replaced. Replace only with the same
type by service or professional agent.
PLEASE LISTEN RESPONSIBLY
The Occupational Safety Health Administration (OSHA) has issued headphone usage recommendations for maximum daily exposure and sound pressure levels (measured in decibels
(dB)). A decibel is a unit of measure of sound, and decibels increase exponentially as sound
gets louder. For example, conversational speech is typically around 60dB, and a rock concert
in a stadium is often about 110dB.
OSHA GUIDELINES FOR NOISE EXPOSURE LIMITS
Sound Pressure Level Recommended Maximum
90dB 8 hours
95dB 4 hours
100dB 2 hours
105dB 1 hours
110dB 30 minutes
115dB 15 minutes
120dB
Exposure Per Day
Avoid as damage may occur
WEEE NOTICE
Note: This mark applies only to countries within the European Union (EU)
and Norway. This appliance is labeled in accordance with European Directive
2002/96/ EC concerning waste electrical and electronic equipment (WEEE). This
label indicates that this product should not be disposed of with household waste.
It should be deposited at an appropriate facility to enable recovery and recycling.
EU COMPLIANCE INFORMATION
Eligible to bear the CE mark; Conforms to European Union Low Voltage Directive 2006/95/
EC; European Union EMC Directive 2004/108/EC; European Union RoHS Directive 2002/95/
EC; European Union WEEE Directive 2002/96/EC; European Union Registration, Evaluation,
Authorization and Restriction of Chemicals (REACH) Directive 2006/121/EC; European Union
Radio and Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC.
This product contains batteries that are covered under the 2006/66/EC European Directive,
which cannot be disposed of with normal household waste. Please follow local regulations.
You may obtain a free copy of the Declaration of Conformity by contacting your dealer, distributor, or Klipsch Group, Inc.’s worldwide headquarters. Contact information can be found
here: http://www.klipsch.com/Contact-Us
WIRELESS TRANSMITTER COMPLIANCE INFORMATION:
The term “IC:” before the radio certification number only signifies that Industry Canada
technical specifications were met.
Le terme «IC:» avant le numéro de certification radio signifie seulement que les spécifications techniques d’Industrie Canada ont été respectées.
This device complies with part 15 of the FCC Rules and the applicable Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
FCC AND CANADA EMC COMPLIANCE INFORMATION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Approved under the verification provision of FCC Part 15 as a Class B Digital Device.
Caution: Changes or modifications not expressly approved by the manufacturer could void
the user’s authority to operate this device.
Caution: To comply with the limits of the Class B digital device, pursuant to Part 15 of the
FCC Rules, this device is to comply with Class B limits. All peripherals must be shielded and
grounded. Operation with non-certified peripherals or non-shielded cables my result in
interference to radio or reception.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
SPECIFICATIONS
Bluetooth v2.1 +EDR
Profiles: A2DP v1.2, AVRCP v1.0, HSP v1.2, HFP v1.6
A2DP Codecs: SBC, AAC, aptX®
Range: Up to 10m (33 feet)
Input rating: 5V DC, 0.5A
STATUS INDICATOR
Example:
Blinks Blue
RRB B
RB
Blinks Red Time Between Blinks
WHAT’S INSIDE
Image ONE Bluetooth Headset
Travel Case Micro USB Charging Cable
Direct Connect Audio Cable
5
4
6
7
3
11
1 2
1. Charging Jack
2. Battery Status Indicator
3. Track Back
4. Status Indicator
5. Power/Pairing
6. Play/Pause, Answer/End Call
8
7. Volume +
8. Volume -
9. Audio Jack
10. Microphone
11. Track Forward
10
9
CHARGING
Charge for 1 hour before first use.
When fully charged the battery will provide up to 10 hours of talking and/
or music time. You can continue to use the headset while charging.
Low battery (Battery Status Indicator):
R RR
PAIRING
Before using the headset for the first time it must be paired with a Bluetooth device (mobile phone, etc.).
1. Ensure the headset is off.
2. Hold the Power/Pairing button for 5 seconds. The headset will turn on
B B B B B
3. Turn on Bluetooth on the device and set it to search for Bluetooth
devices.
4. Select “Klipsch BT ImageONE” from the device list.
5. If prompted to enter a passcode enter 0000.
Once a device has been paired the headset will remember it. When the
headset is turned on it will automatically scan for remembered devices,
beginning with the most recently paired. Up to 8 devices are memorized.
TURNING ON/OFF
then the status indicator will rapidly flash
Hold 3 seconds
Status Indicator
ON
B B B B B
OFF
R R R R R
R B R B
VOLUME & MUSIC CONTROLS
Previous Track
Volume Up
Volume Down
CALLS
Make calls as normal from the phone, when the headset is connected the
audio will automatically go to the headset.
Power/Pairing
• Mute - Press once
• Transfer audio between
headset and phone
- Hold 2 seconds
DISCONNECT THE HEADSET
To disconnect the headset from a device, power the headset off or
disconnect it in the Bluetooth menu of the device.
Next Track
Play / Pause
Play/Pause, Answer/End Call
• Answer/End call - Press once
• Reject call - Hold 2 seconds
RECONNECT THE HEADSET
To connect to the most recently used device, power the headset on. If
Bluetooth is enabled on the device they will automatically reconnect. To
connect to another remembered device, select “Klipsch BT Image ONE”
from the Bluetooth menu of the device.
CLEARING REMEMBERED DEVICES
To clear the paired device memory from the headset:
1. Power headset off
2. Hold Power/Pairing & Volume –
buttons together for 8 seconds
R RR R BBB B
USING WITH THE DIRECT CONNECT AUDIO CABLE
The headset can be connected to an audio source using the direct connect
audio cable. Note: When the audio cable is connected the Bluetooth
function and controls are disabled.
STATUS INDICATOR
Blinks Blue
General and Standby
RB
Blinks Red Time Between Blinks
Pairing
Low Battery
Standby (Bluetooth Connected)
Standby (Bluetooth Not Connected)
A2DP (Streaming Audio)
A2DP active, SBC codec
A2DP active, AAC codec
A2DP active, aptX codec
HSP (Phone Calls)
Incoming / Outgoing call
Active Call
R RRR RRB BBB BB
R RR
B BBB BB
R RRR RR
B BBB BB
B BBB BBB BB
B BB BB BB B
B BBB BB
B BBB BB
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.
and any use of such marks by Klipsch Group, Inc. is under license. Other
trademarks and trade names are those of their respective owners.
The “aptX® software is copyright CSR plc or its group companies. All
rights reserved. The aptX® mark and the aptX logo are trade marks of
CSR plc or one of its group companies and may be registered in one or
more jurisdictions.”
3502 WOODVIEW TRACE, INDIANAPOLIS, IN, USA
klipsch.com
©2012, Klipsch Group, Inc.
Loading...