FUJIFILM FinePix Z1 TROUBLESHOOTING GUIDE

DIGITAL CAMERA

FinePix Z1

TROUBLESHOOTING GUIDE

US/CA/EU/EG/GE/AS/CH/JP-Model

z THE COMPONENTS IDENTIFIED WITH THE MARK “

DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.
PLEASE REPLACE ONLY WITH THE COMPONENTS SPECIFIED ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST.

WARNING

” ON THE SCHEMATIC

z IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND AN

ELECTRICAL SHOCK.

Ref.No.: ZM00596-400

FUJI PHOTO FILM CO., LTD.

Printed in Japan 2005. 10

FinePix Z1 TROUBLESHOOTING GUIDE

SAFETY CHECK-OUT

After correcting the original problem, perform the following

safety check before return the product to the customer.

1. Check the area of your repair for unsoldered or
poorly soldered connections. Check the entire
board surface for solder splasher and bridges.

2. Check the interboard wiring to ensure that no
wires are “pinched” or contact high-wattage
resistors.

3. Look for unauthorized replacement parts,
particularly transistors, that were installed during
a previous repair. Point them out to the customer
and recommend their replacement.

4. Look for parts which, though functioning, show
obvious signs of deterioration. Point them out to
the customer and recommend their replacement.

5. Check the B + voltage to see it is at the values
specified.

6. Make leakage - current measurements to
determine that exposed parts are acceptably
insulated from the supply circuit before returning
the product to the customer.

7.

2.5A 125V

2.5A 125V

8.

RISK OF FIRE­REPLACE FUSE
AS MARKED

WARNING!

HIGH VOLTAGE

CAUTION: FOR CONTINUED
PROTECTION AGAINST FIRE
HAZARD, REPLACE ONLY
WITH SAME TYPE 2.5
AMPERES 125V FUSE.

ATTENTION: AFIN
D'ASSURER UNE
PROTECTION PERMANENTE
CONTRE LES RISQUES
D'INCENDIE, REMPLACER
UNIQUEMENT PAR UN
FUSIBLE DE MEME, TYPE 2.5
AMPERES, 125 VOLTS.

WARNING:

TO REDUCE THE ELECTRIC
SHOCK, BE CAREFUL TO
TOUCH THE PARTS.

2

FinePix Z1 TROUBLESHOOTING GUIDE

TABLE of CONTENTS

1. Power.........................................................................................................................4

1-1. The camera does not turn on.....................................................................................................4

1-2. The camera does not turn on.....................................................................................................4

1-3. The camera does not turn on.....................................................................................................4

1-4. The camera does not turn on.....................................................................................................5

1-5. The camera does not turn on.....................................................................................................5

1-6. The camera does not turn on.....................................................................................................5

1-7. The camera does not turn on.....................................................................................................6

1-8. The camera does not turn on.....................................................................................................6

2. Lens............................................................................................................................7

2-1. Zoom error .................................................................................................................................7

2-2. Noise appears in recorded images ............................................................................................7

3. LCD.............................................................................................................................7

3-1. No image on the LCD.................................................................................................................7

4. Other ..........................................................................................................................8

4-1. The camera buttons do not work................................................................................................8

4-2. The camera will not record sound..............................................................................................8

4-3. The flash does not fire................................................................................................................9

4-4. There is a gap between the battery cover and the rear panel....................................................9

4-5. There is a gap in the front panel ................................................................................................9

4-6. The lens cover is stiff when opening and closing.....................................................................10

4-7. Faulty lens cover operation......................................................................................................10

3

FinePix Z1 TROUBLESHOOTING GUIDE

g

1. Power

1-1. The camera does not turn on

Fault details: When the camera is turned on, the current of two amperes momentarily but the camera is

not activated.

Analysis results: The covering on the MIC ASSY wire is split and the wire is short-circuiting with the zoom

motor earth lead.

* If the MIC ASSY is installed with the wires

crossed, the coatings press together as shown in
the figure on the left and there is a risk of a short­circuit occurring. The MIC ASSY should be
rotated so that the wires do not cross.

Repair details:

Replace the MIC ASSY

1-2. The camera does not turn on

Fault details: The camera does not turn on in Camera mode, but starts up normally in Playback mode.
Analysis results: Power is not supplied due to deformation in the RSW power switch.

Switch deformation Normal switch

Repair details:

Replace the RSW ASSY

1-3. The camera does not turn on

Fault details: The camera does not turn on in Camera mode, but starts up normally in Playback mode.
Analysis results: Power is not supplied due to a wire breakage in RSW FPC contact s .

Repair details:

Replace the RSW ASSY

4

* When inserting the wire harness into the

connector, insert the wire horizontally.
Inserting the wire harness on an angle
may result in a wire breakage as shown

ure on the left.

the fi

in