Fuji Film 02000003 Users Manual

User Manual

WIRELESS LAN MODULE

MODEL FZ00010935-700

The purpose of this manual is to explain correct way how to integrate module FZ00010935-700 to
the end product. It includes procedures that shall assist you to avoid unforeseen problems.
This manual presents information that shows how module and OEM product, where module
integrated,complies with regulations in certain regions. Any modifications, not expressly approved
by the manufacturer could void the authority to operate in these regions.
The wireless LAN module, model FZ00010935-700 has to be installed and used in accordance with
the technical description/installation instructions provided by the manufacturer.
For detail information concerning type approval of this module (e.g. where this module is already
pre-approved) please contact the authorized local distributor or the manufacturer.
The system may only be implemented in the configuration that was authorized.
Note that any changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.

Regulatory Information

Operational Information

Wireless Interoperability

The end product integrating this module is designed to be interoperable with any wireless LAN
product that is based on direct sequence spread spectrum (DSSS) and orthogonal frequency
division multiplexing (OFDM) radio technology and to comply with the following standards.

･IEEE Std 802.11b Standard on 2.4GHz Wireless LAN

･IEEE Std 802.11g Standard on 2.4GHz Wireless LAN

･IEEE Std 802.11ｎ Standard on 2.4GHz Wireless LAN

Federal Communications Commission (FCC) Statement

15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

-Consult the dealer or an experienced radio/TV technician for help.

15.21: You are cautioned that changes or modifications not expressly approved by the part
responsible for compliance could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement:

1.This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.

2.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.

FCC RF Exposure requirements:

This device and its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter.

15.19
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

1) this device may not cause harmful interference and

2) this device must accept any interference received, including interference that may cause undesired
operation of the device.

Labeling:

Wireless LAN module FZ00010935-700 labeled as below.
FCC ID: W2Z-02000003
The proposed with FCC ID label format is to be placed on the module. If FCC ID is not visible when
the module is installed into the system, “Contains FCC ID:
W2Z-02000003” shall be placed on the outside of final host system

Instructions to OEM Integrators

A User manual provided to the end user must indicate the operating requirements and conditions
that must be observed to ensure compliance with the above-mentioned FCC RF Exposure
guideline.
If this module is intended for use in a portable device, integrators are responsible for separate
evaluation and/or approval to satisfy FCC RF Exposure requirements.
The antenna used this module is as follows;
Antenna Type: PCB printed antenna
Antenna Gain: -4.14dBi
If an antenna with higher gain or new antenna type is used with this module, integrators must
contact to manufacture for additional testing and submission to the FCC.
If other radio devices are to be integrated with this module, an additional evaluation and FCC
submission may be required. Integrators are responsible for such additional evaluation and FCC
submission.

Industry Canada Statement

This device complies with RSS-247 of Industry Canada. Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.

RF Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between
the radiator and your body.

Avis d’industrie Canada:

Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence.
L'exploitation est autorisee aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et, and (2) l'utilisateur de l'appareil doit accepter tout
brouillage
radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.

RF exposure:

To comply with the IC RF ex posur e compl ia nce requirements, this d evice and its antenna must not be
co-located or operating in conjunction with any other antenna or transmitter.
Pour se conformer aux exigences de conformité RF canadienne l'exposition, cet appareil et son
antenne ne doivent pas être co-localisés ou fonctionnant en conjonction avec une autre antenne ou
transmetteur.

Industry Canada Class B Emission Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Avis de conformite a la reglementation d'Industrie Canada:

Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non c ontrôl é. Cet éq uip ement doit être i nstall é et utili sé av ec un mini mu m de 20 cm de
distance entre la source de rayonnement et votre corps.

Labeling:

Wireless LAN module FZ00010935-700 labeled as below.
IC: 7736B-02000003
The proposed with IC ID label format is to be placed on the module. If IC ID is not visible when the
module is installed in to the system, “Contains IC: 7736B-02000003” shall be placed on the outside
of final host system.