Fuji Film 02000001 Users Manual

FZ09396-100

User’s Manual

- 1 -

Notice:

This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.

Warning:

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device is to be used only for mobile and fixed applications. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio/TV technician for help  The host device shall also comply with the certification labeling requirements of each of the

modules it contains.

 A reference to the enclosed module displaying its FCC and IC ID certification number.  Recommended wording:

* Contains FCC ID: W2Z-02000001 * Contains IC ID: 7736B-02000001

SPECIFICATON

（1）

APPROVED BY CHECKED BY DESIGNED BY

技術部

'10.11.28

統括課長

和気

技術部

'10.11.28

主幹

内田

技術部

'11.11.28

町田

MODEL:

This products Standard shall be applied to the Wireless LAN module(DWM-W078) 本規格は、無線LANモジュール(DWM-W078)について規定する。

Contents.

No. No. 1 Product summary

Scope

1-1 1-2 General explanation

Hardware specification

2 2-1 Block diagram

Environmental condition

2-2 2-3 Power supply

3 Electrical characteristics

Channel plan

3-1 3-2 Power Sequence 3-3 Interface specification 3-4 SDIO Protocol Timing 3-5 Current consumption 3-6 Antenna specification 3-7 Reciever characteristics

Transmitter characteristics

3-8

Measurement method

Tx test condition

4-1

Rx test condition

4-2

Item Page Item

DWM-W078 Formed on.

2 2 2

3 3 3 3

4-10

4 4 4 5 6 7 7

8-10

11 11 11

2011.11.28

Page

Mechanical specification

Dimension

5-1

Weight

5-2 5-3 Terminal number and name

6 Reliability Test

Revision

ＭＩＴＳＵＭＩ　ＥＬＥＣＴＲＩＣ　ＣＯ．，ＬＴＤ．

12 12 12 12

SYM.

GROUP NO. DWG.NO.

S19

0980

（2）

1.Product Summary 製品概要

1-1. Scope

2.4 GHz WLAN module with integrated antenna (IEEE802.11 b/g/n supported）

2.4GHz帯アンテナ一体無線LANモジュール (IEEE802.11 b/g/n 準拠）

1-2. General explanation

Standard IEEE802.11ｂ/ｇ/n Frequency Host Interfase Frequency Bandwidth 20MHz

Weight 0.5g typ

・Chipset: MARVELL Semiconductor Inc. 88W8787L（CPS Package）・Modulation Types: DBPSK, DQPSK and CCK with 802.11b mode 　OFDM(BPSK, QPSK, 16-QAM and 64-QAM) with 802.11g/n mode ・Data rate: 1,2,5.5 and 11 with 802.11b mode 　6,9,12,18,24,36,48 and 54 with 802.11g mode 　MCS0-7 with 802.11n mode ・Security: WEP(64 and 128bits), WPA-PSK(TKIP/AES) and WPA2-PSK(TKIP/AES)

2.4-2.4835GHz SDIO ver2.0

DWG.NO.

0980

ＭＩＴＳＵＭＩ　ＥＬＥＣＴＲＩＣ　ＣＯ．，ＬＴＤ．

（3）

2.Hardware Specification

2-1. Block diagram

ブロック図

Anntena

RF Switch Connector

LPF

DPDT

RF Switch

2-2. Environmental condition

環境条件

1) Operating environment 動作環境条件　 Operating temperature range

動作温度範囲 : -20 ～ 70 ℃ Operating humidity range 動作湿度範囲 : 20%～80%(None dew) 結露無き事

2) Storage environment 保存環境条件

Storage temperature range 保存温度範囲 : -30 ～ 85 ℃ Storage humidity range 保存湿度範囲

Power

Amp

RF TX

PMU(1.2V)

88W8787L

MARVELL

RF RX

32kHz

RTC Clock

Serial

EEPROM

88W8787 (CSP)

38.4MHz XTAL

: 20%～85%(None dew) 結露無き事

SDIO I/F

VIO

Pdn

HostWakeup

VDD33

+1.8V

LDO

2-3. Power supply

Symbol

VDD33 3.30

MIN．

2.97

1.62

VIO

2.50

2.97

Value

TYP．

1.80

2.60

3.30

MAX．

UNIT

3.63

1.98

2.70

3.63 V

V V V

DWG.NO.

0980

ＭＩＴＳＵＭＩ　ＥＬＥＣＴＲＩＣ　ＣＯ．，ＬＴＤ．

+ 10 hidden pages