Page 1
!
FEANG1: LP TO NG CONVERSION KIT INSTRUCTION MANUAL
Models FELG21C & FELG21S
!
FEANG1 includes the following components:
1 - 10 foot 3/8" ID gas hose with quick connect
1 - 1.70mm natural gas orifice for Outer Burner
1 - 1.06mm natural gas orifice for Inner Burner
!
Connection: Operating pressure: 7.0" W.C.
!
Check with your local gas utility company or with local codes for instructions on installing gas supply lines. Be sure
to check on type and size of run, and how deep to bury the line. If the gas line is too small, the grill will not
function properly. Any joint sealant used must be an approved type and be resistive to the actions of natural gases.
(This type of connection should be performed by a certified or licensed technician only.)
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
NOTE: Do not use natural gas orifices with an LP gas tank or LP gas orifices with natural gas. Do gas leakage
testing after per conversion. Please note the Gas Hook-Up, Danger, and Warnings pages in the manual for more
information.
www.fuegoliving.com
Assembly Instructions:
!
1) Assemble as shown below (FIG. 01). Remove the front
door. Use a pipe wrench to hold the grill inlet pipe to avoid
shifting any internal gas lines of the grill. Remove the preattached LP gas hose pipe from the inlet fitting of the grill.
Attach the 3/8" ID gas hose on.
!
2) Assemble as shown below (FIG. 02) Use screwdriver to
remove screws holding burner to grill body by unscrewing
counter-clockwise to remove the burner kit.!
!
3) Use a wrench to unscrew the LP gas orifice by turning
counter-clockwise and replace with natural gas orifice.
Use the 1.70mm orifice(Silver) for the Outer Burner ring
and the 1.06mm orifice(Brass) for the Inner Burner ring.
Note: The natural gas orifice has a larger hole in the
center to keep the flow of natural gas consistent.
!
4) After the replacement, properly locate and re-attach the
burner kit with respect to the orifices. Adjust the igniter
tip located near the burner edge. (FIG. 03)!
!
5) Connect the NG hose assembly to fixed NG piping system.
(FIG. 04) Turn on gas supply and do the leak testing as
the procedures shown on page 26 of main manual. Read
all lighting instructions on main manual prior to lighting.
!
6) After the conversion is done, apply the rating plate on the
unit.
!
A) The outdoor cooking gas appliance and its individual
shutoff valve must be disconnected from the gas
supply system during any pressure testing of that
system at test pressures in excess of 0.5psi(3.5kpa)
!
B) The outdoor cooking gas appliance must be isolated
from the gas supply piping system by closing its
individual manual shutoff valve during any pressure
testing of the gas supply piping system at test
pressures equal to or less than 0.5psi(3.5kpa).
Fuego Living LLC
5042 Wilshire Blvd #29997
Los Angeles, CA 90036
888-88-FUEGO
info@fuegoliving.com
FIG. 01
FIG. 02
FIG. 03
FIG. 04
3/8” NG Hose
(Brass) ORIFICE 1.06MM!
FOR INNER BURNER
(Brass) ORIFICE 1.70MM!
FOR OUTER BURNER
(Brass) ORIFICE 1.70MM!
FOR OUTER BURNER
(Brass) ORIFICE 1.06MM!
FOR INNER BURNER
Loading...