Fubag 100111 User Manual [ru]

Пневмогайковерт

Air wrench

100102
100107
100108
100109
100110

100111
100112
100121
100122
100126

Operator's Manual

Инструкция по эксплуатации

www.fubag.ru

Omperator's anual

www.fubag.ru

WARNING!BEFORE USING AIR PLEASE READ THISINSTRUCTION MANUAL
CAREFULLY.
ONLY QUALIFIED AND WELL-TRAINED STAFF ACQUAINTED WITH THE MANUAL
CAN USE AND OPERATE THIS TOOL.

The operation manual contains the description, safety rules and all the information necessary for
proper maintenance of FUBAG pneumatic tool. Please keep the operation manual and refer to it in
case of any questions concerning safety operation, maintenance, storage and transportation of
FUBAG tool. Nonobservance of the indicated recommendations may cause the damage of the tool
and injuries ofthe user.

TOOL

1. Safety rules

- General safety requirements are to conform to EN 792-9.

- Only the persons who have taken the preliminary training and are aware of the tool
structure, safety rules and the requirements of the operation manual can operate the tool.

- Vibration characteristics of the tool correspond to EN ISO 8662-1 requirements. The use of
the tool is not allowed for the operations when vibration levels exceed the values
established by EN ISO 8662-1.

- Noise characteristics of the tool correspond to EN ISO 11202 requirements. The corrected
level of the noise power does not exceed 99 dBA. The use of the tool is not allowed for the
operations when noise levels exceed the values established by EN ISO 11202.When
operating the tool it is strongly recommended to use the protective spectacles, headphones
and protective gloves.

- Always keep the steady foot rest in order not to stumble. Always fasten the workpiece with a
fixer or a grip to release two hands for operating with the tool.

- The tool with the ratchet mechanism may give a return and cause an injury if the nut is run
too tightly. In this case use the manual tool to slacken the nut before the nutrunner use.

- Sudden movement of the tool on account of the reaction force or the break down of the
drive socket may cause an injury.

- In case of the drive socket destruction it may become dangerous for the personnel because
of the smashed parts.

- Avoid whipping with the air compressed hose.

- The tool is not eclectically isolated thus avoid its contact with the electricity sources.

- Make sure all the clothes fit closely to the body.

- Make sure there are not any foreign objects in the place of operation; and there are not any
people in the proximity of the operating tool.

- The workplace is to be aired well.

- Make sure the tool is in OFF position before connecting the air hose.

- Always disconnect the tool from the aerial system when it is not used.

- Do not pull the hose when transporting the tool.

- 1 -

Omperator's anual

www.fubag.ru

Danger:

-

Do not direct the pneumatic tool or flow of the compressed air at the people, animals or
your own body. Wear protective spectacles in order to avoid small particles of the dust to
get into your eyes together with the flow of the compressed air.

-

Do not direct the flow of the compressed air at the compressor.

-

Do not work without any protective footwear. Do not touch the operating compressor with
wet hands and/or feet.

-

Do not exceed the recommended operating pressure.

-

Do not fix, disassemble or carry out any other maintenance operations without
disconnecting the tool from the air channel.

-

Do not use the spare parts of the other manufacturers. Always use only original spare parts.

Caution:

--When connecting the pneumatic tool to the compressor hose always block the air escape
cock.

Always follow the safety rules when using the compressed air.

If revealing any faults immediately discontinue the operation.

2. Description

The is a manual pneumatic tool designed for screwing and unscrewing of the rigid threaded

wrench

connections.

3s. Technical pecifications

Tail size, inch 1/2 1/2 1/2 1/2 1/2
Screwed bolt Max diameter, mm 14 12 12 14 16
No load rotation speed, rpm 7000 150 150 7000 7500
Max torque, Nm 312 61 61 312 680
Inlet diameter, inch 1/4 1/4 1/4 1/4 1/4
Total air consumption, l/min 623 538 538 623 765
Average air consumption at work cycle min , l/min 156 135 135 156 192
Operation pressure, bar 6,3 6,3 6,3 6,3 6,3
Weight, kg 2,18 1,12 1,12 2,18 2,42
Air conductive hose diameter recommended, mm 6х8 6х8 6х8 6х8 6х8

Tail size, inch 3/4 3/4 1/2 3/4 1/2
Screwed bolt Max diameter, mm 19 32 16 19 12
No load rotation speed, rpm 4800 4500 7500 4800 150
Max torque, Nm 680 1600 680 680 61
Inlet diameter, inch 1/4 1/4 1/4 1/4 1/4
Total air consumption, l/min 934 1048 765 934 538
Average air consumption at work cycle min , l/min 234 262 192 234 135
Operation pressure, bar 6,3 6,3 6,3 6,3 6,3
Weight, kg 3,09 5,89 2,42 3,09 1,12
Air conductive hose diameter recommended, mm 6х8 6х8 6х8 6х8 6х8

The manufacturer reserves himself the right to make the manual's content or function
change without anypreliminary notification of theusers.

MODEL 100102 100107 100108 100109 100110

MODEL 100111 100112 100121 100122 100126

tools

--2