Page 1
TS-400 INSTALLATION INSTRUCTIONS
FSR
1.
DETERMINE LOCATION OF TS-400 ASSEMBLY AND REMOVE APPROPRIATE KNOCK-OUT PANELS FOR WIRES/CONDUITS
ROUTED TO THE TS-400 UNIT. USE THE TS-400 CHASSIS AS A TEMPLATE TO TRANSFER THE .328 DIAMETER HOLE
PATTERN TO WALL AND CEILING. HOLES USED TO SECURE CHASSIS WILL BE DETEREMINED ON SITE BY INSTALLER.
INSTALLER TO PROVIDE HARDWARE OR USE SUPPLIED TOGGLE BOLTS.
SHEET ROCK (1/2" MIN) / METAL STUD APPLICATIONS - WALL ANCHOR LOCATIONS - 6 TOP ROW, 2
SHEET ROCK (1/2" MIN) / WOOD STUD APPLICATIONS - LAG BOLTS WITH WASHERS MAY BE USED TO INSTALL
244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - Fax: 973.785.4207
BOTTOM ROW, MINIMUM 16" SPAN
TO WOODEN STUDS. WALL ANCHOR LOCATIONS - 2
TOP ROW, 2 BOTTOM ROW, MINIMUM 16" SPAN
BLOCK CONSTRUCTION - USE APPROPRIATE ANCHORS OR PROVIDED TOGGLE
BOLTS. WALL ANCHOR LOCATIONS - 2 TOP ROW, 2
BOTTOM ROW, MINIMUM 16" SPAN.
TS-400 - MAXIMUM
EQUIPMENT
LOAD - 50 LBS
CEILING
WALL
CEILING
WALL
WALL
TS-400 WITH COVER
B
43218 LIT1422
CEILING
TS-400 WITHOUT COVER
B
WALL
CEILING
A
A
.328 DIA. HOLES
14 POSSIBLE WALL
MOUNTING HOLES
.328 DIA. HOLES
15 POSSIBLE CEILING
MOUNTING HOLES -
IF CEILING MOUNT
IN LIEU OF WALL
MOUNT, MUST
SECURE TO
STRUCTURAL
WALL
MEMBER
SECTION A-A
SECTION B-B
CEILING
WALL
Page 2
TO CEILING
ELECTRICAL DEVICE
(SUPPLIED BY CUSTOMER)
TS-400 CHASSIS
(COVER REMOVED)
REMOVE THIS FEATURE
FOR ELECTRICAL BOX
INSTALLATION ONLY
OPENING FOR
WIRES AND CABLES
(2) 1" CONDUIT
KNOCKOUT
TO WALL
(3) 1/2" & 3/4" CONDUIT
KNOCK-OUT
LOW SIGNAL DETAIL
ADDITIONAL OUTLETS
OR ELECTRICAL
DEVICES (SUPPLIED
BY CUSTOMER)
2-GANG ELECTRICAL
BOX (SUPPLIED BY
CUSTOMER)
USE SCREWDRIVER
TO REMOVE PLATES
AS REQUIRED
REMOVE THIS PLATE FOR
LOW VOLTAGE SIGNAL USE
AND
ELECTRIC BOX
INSTALLATION
TIE-WRAP POINT
TO SECURE WIRES
AND CABLES
REMOVE THIS FEATURE
FOR ELECTRICAL BOX
INSTALLATION ONLY
ELECTRIC BOX INSTALLATION DETAIL
Page 3
CEILING
#6-32 x .375
PAN HEAD
SCREW
CABLE
CLAMP
RACK MOUNT
BRACKETS
ALTERNATE
RACK MOUNT
HOLES
IPS MOUNTING
PLATE
#6-32 KEP NUT
SEE WIRE
SADDLE
DETAIL
.188 DIA HOLE
CABLE CLAMP DETAIL
AFTER INSTALLATION OF ELECTRONIC
DEVICES, SECURE CABLE CLAMPS AS
REQUIRED TO THE VARIOUS .188 DIAMETER
HOLES TO ROUTE CABLES THRU THE TS-400
CHASSIS.
.188 DIA. HOLE
WIRE
SADDLE
WIRE SADDLE DETAIL
AFTER INSTALLATION OF
ELECTRONIC DEVI C E S,
SECURE WIRE SADDLES AS
REQUIRED TO THE VARIOUS
.188 DIAMETER HOLES TO
ROUTE CABLES THRU THE
TS-400 CHASSIS.
SEE CABLE
CLAMP
DETAIL
WALL
Page 4
1/4" TOGGLE BOLT INSTALLATION (8 PROVIDED)
1a. 1b.
STRAP
DRILL 1/2" DIA. HOLE
CAP
DRYWALL
CHANNEL
1c. 1d.
HOLD CHANNEL FLAT ALONG
STRAP AND SLIDE CHANNEL
THRU HOLE
PULL STRAPS UNTIL CHANNEL RESTS
FLUSH BEHIND WALL, THEN SLIDE CAP
UNTIL FLANGE OF CAP IS FLUSH
WITH WALL
1e.
SNAP STRAPS AT WALL BY
PUSHING SIDE TO SIDE,
SNAPPING OFF STRAPS
LEVEL WITH FLANGE OF CAP
1f.
SECURE TS-400 CHASSIS WITH
1/4"-20 HARDWARE (8 PROVIDED)
Page 5
2.
AFTER CHASSIS IS MOUNTED TO WALL, INSTALL COVER'S SAFETY CABLE TO CHASSIS.
TS-400 CHASSIS
CAPTURE TAB
SEE SAFETY
CABLE DETAIL
CAPTURE TAB
a.
b.
SAFETY CABLE
PIN
CAPTURE TAB - OPEN POSITION
c.
(2) SAFETY CABLE
TS-400 COVER
SAFETY CABLE
CAPTURE TAB - CLOSED POSITION
(a.) ROTATE CABLE CAPTURE TAB AWAY FROM PIN.
(b.) INSTALL COVER SAFETY CABLE ONTO PIN.
(c.) ROTATE CABLE CAPTURE TAB BACK TO PIN
SAFETY CABLE DETAIL
Page 6
3.
INSTALL COVER ONTO CHASSIS. MAINTAIN TENSION
ON SAFETY CABLE WHILE POSITIONING COVER TO
CHASSIS. REVERSE STEPS TO REMOVE COVER FROM
CHASSIS.
SEE LOCK DETAIL
UNLOCKED POSITION LOCKED POSITION
LOCK DETAIL
SUPPORT COVER AT
THESE LOCATIONS
MAINTAIN TENSION ON
SAFETY CABLE WHILE
MOVING COVER UP
TO CHASSIS
TOP OF CHASSIS
BOTTOM OF COVER
WHILE KEEPING TENSION
ON SAFETY CABLE, ENSURE
BOTTOM SURFACE OF COVER
IS PARALLEL WITH TOP
OF CHASSIS
a.
b.
ONCE COVER STOPS AGAINST CHASSIS,
WHILE PUSHING UP, (a.) SLIDE COVER
TOWARDS WALL UNTIL IT STOPS AND
(b.) ALLOW COVER TO DROP DOWN
APPROXIMATELY 1/8" TO INTERLOCK
WITH CHASSIS.
Loading...