FSR TM-IPAD-TR User Manual

6a.

PLACE IPAD ONTO FRONT PANEL AND CONNECT CONNECTOR.

FSR

TM-IPAD-TR / TM-IPAD-TRS / TM-IPMINI-TR / TM-IPMINI-TRS INSTALLATION INSTRUCTIONS

244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: [phone] - Fax: [phone]

POSITION IPAD BETWEEN
TABS OF FRONT COVER

FRONT

PANEL

REAR VIEW OF FRONT PANEL

INSTALL #6-32 NUT

DISABLE

IPAD (SUPPLIED

BY CUSTOMER)

IPAD

(SUPPLIED) TO

POWER

SWITCH LEVER

CONNECT TO IPAD BEFORE

REASSEMBLY OF FRONT PANEL

FRONT PANEL

1.

REMOVE BASE COVER.

2a.

STANDARD BASE MOUNTING:

IF REQUIRED DRILL 3/4 DIA.
HOLE FOR CABLE PASS-THRU

9 POSSIBLE MOUNTING

HOLES (RECOMMEND

3 MINIMUM), TRANSFER

BASE COVER

(RETAIN FOR

REASSEMBLY)

(2) COVER SCREW

(RETAIN FOR

REASSEMBLY)

PATTERN FROM BASE

DRILL 5/64 DIA. PILOT HOLES FOR

#8 SCREWS (SUPPLIED)

TO SURFACE.

6b.

REINSTALL FRONT PANEL AS SHOWN BELOW WHILE
HOLDING IPAD IN PLACE. SECURE WITH ORIGINAL SCREWS.

(4) COVER SCREW

USE PENCIL

(ERASER END)

TO ACTIVATE

POWER SWITCH

REMOVE COVER FOR

HORIZONTAL / VERTICAL

LOCKING OPTION S

ENSURE SWITCHES ARE PROPERLY
SET BEFORE REASSEMBLY OF
FRONT PANEL

FOR VERTICAL

LOCK POSITION

COVER
SHOWN
REMOVED

FOR HORIZONTAL
LOCK POSITION

HORIZONTAL / VERTICAL

LOCKING OPTIONS

(ALL MODELS)

ROTATE IPAD HORIZONTALLY

OR VERTICALLY AND INSTALL

#6-32 x 1/2 LG PAN-HEAD

SCREW (SUPPLIED) IN

CORRESPONDING HOLE

2b.

SWIVEL BASE MOUNTING:

BEFORE INSTALLING LOCK ING

SCREWS, CENTER IPAD ON

C

B

INSERT #6-32 x 1/4 LG

PAN-HEAD SCREW

(SUPPLIED) TO DISABLE

SWIVEL FEATURE

SWIVEL RANGE

NO SCREWS -

HOLE A ­HOLE B ­HOLE C -

BASE (AS SHOWN)

A

A

C

B

180°
140°
104°
90°

REMAINING HOLES FROM

DRILL 5/64 DIA. PILOT HOLES
FOR #8 SCREWS (SUPPLIED)

INSERT #6-32 x 1/4 LG PAN-HEAD
SCREWS (SUPPLIED) TO
CORRESPONDING LETTERS TO
CHANGE SWIVEL RANGE

MOUNTING HOLES ACCESSED

DRILL PILOT HOLES

FOR DIMENSIONED

HOLES AND TRANSFER

BASE TO SURFACE.

RECOMMEND DRILLING

3/4 DIA. HOLE FOR

CABLE PASS-THRU

SWIVEL UNIT

CLOCKWISE TO

ACCESS HOLE

HOLE ACCESSIBLE

WHEN UNIT IS

SWIVELED

BY SWIVELING UNIT

(SEE BELOW)

3.46
MIN.

1.50 1.50

COUNTER-

1.50 1.50

43036 LIT1452

3.

SKIP TO STEP 4 IF NOT USING USB CHARGER
SNAP-IN CONNECTOR OPTION.

3a.

REMOVE SNAP-IN BRACKET.

SNAP-IN BRACKET

(INCLUDED)

4.

REASSEMBLE BASE COVER.

(2) COVER SCREW

BASE COVER

5.

(4) COVER SCREW

(RETAIN FOR

REASSEMBLY)

REMOVE FRONT COVER.

FRONT COVER
(RETAIN FOR
REASSEMBLY)

#6 FLAT-HEAD SCREW

(RETAIN FOR REASSEMBLY)

3b.

INSTALL USB CHARGER SNAP-IN CONNECTOR ONTO SNAP-IN
BRACKET. CONNECT USB END TO USB CHARGER.

INCLUDED APPLE

CORD, USB END

USB CHARGER

SNAP-IN CONNECTOR

(USB CHARGER KIT

SOLD SEPARATELY)

3c.

REINSTALL SNAP-IN BRACKET ASSEMBLY.

SNAP-IN BRACKET

WIRING STRAIN RELIEF
TIE WRAP HOLE

ROUTE POWER SUPPLY WIRING THRU
CABLE PASS-THRU (RECOMMENDED) AND
MAKE NECESSARY TERMINAL CONNECTIONS
(SEE KIT INSTALLATION INSTRUCTIONS)

HIGHLY RECOMMENDED WIRES BE
ROUTED THRU CABLE ACCESS HOLE
FOR SWIVEL UNITS

ROUTE USB CONNECTOR (OR POWER
SUPPLY WIRING IF USING USB CHARGER KIT)
THRU COVER OR CABLE ACCESS HOLE
AS REQUIRED

6.

REASSEMBLE FRONT PANEL WITH IPAD. EXPLODED VIEW FOR
REFERENCE. SEE BACK PAGE FOR FINAL ASSEMBLY.

IPAD (SUPPLIED BY CUSTOMER)

(4) COVER SCREW

SNAP-IN BRACKET

ASSEMBLY

#6 FLAT-HEAD SCREW

FRONT COVER

IPAD CONNECTOR (SUPPLIED)