FSR CB-12P User Manual

CB-12P INSTALLATION INSTRUCTIONS

FSR

1.

PRIOR TO CEILING INSTALLATION, DETERMINE MOUNTING LOCATION
OF THE FLANGE FOR THE PROJECTOR MOUNT. IF DEFAULT FACTORY
LOCATION WILL BE USED, PROCEED TO STEP 2. IF CHANGING TO
ALTERNATE LOCATION, FOLLOW STEPS 1a THRU 1b.

NOTE: FLANGE LOCATION CAN BE CHANGED AFTER
CEILING INSTALLATION.

1a. 1b.

REMOVE POLE MOUNT PLATE COVER (COVER
SCREWS LOCATED IN INTERIOR OF CEILING BOX).

PART OF

POLE MOUNT

PLATE COVER

244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: [phone] - Fax: [phone]

COVER SCREWS LOCATED IN
INTERIOR OF CEILING BOX

(2) PLUG

MAKE SURE PROJECTOR

MOUNT SET SCREW IS

ORIENTED TOWARDS THE

ACCESS HOLE IN THE POLE

SET SCREW ACCESS HOLE

POLE MOUNT
PLATE COVER

REMOVE FLANGE AND MOVE TO ALTERNATE
LOCATION. CHANGE PLUG LOCATION ON THE POLE
MOUNT PLATE COVER AS REQUIRED, AND
RE-INSTALL THE PLATE COVER WITH THE (2)
ORIGINAL SCREWS.

(4) #10-32 x 3/4" LONG
HEX SCREW

(4) #10 LOCK WASHERS

MOUNT PLATE

POLE MOUNT FLANGE

POLE MOUNT PLATE

2.

INSTALL CB-12P TO A STRUCTURAL CEILING ABLE TO
SUPPORT FIVE TIMES THE NOTED GROSS WEIGHT. USE
APPROPRIATE MOUNTING METHODS BASED ON LOCAL
BUILDING CODES. INSTALL SAFETY CABLE AS REQUIRED BY
LOCAL BUILDING CODES. ROUTE CONDUITS TO BOX AS
REQUIRED.

NOTE: MAXIMUM GROSS WEIGHT - 110 LBS

NOTE: THREADED ROD IS THE
RECOMMENDED CEILING BOX
MOUNTING SUSPENSION
(SHOWN), TO MINIMIZE
FIXTURE TILTING DUE
TO THE WEIGHT OF ANY
SUSPENDED EQUIPMENT.

14 GA. STEEL TIE WIRE MAY BE USED

(SUPPLIED BY CUSTOMER OR USE FSR KIT)

AT 70,000 PSI TENSILE STRENGT H OR

BETTER AS REQUIRED BY BUILDING CODES.

AVAILABLE KITS (SOLD SEPARATELY):
CB-MNT1 - CABLE INSTALLATION KIT
CB-THRD - THREADED ROD INSTALLATION KIT

NOTE: WIRES SUPPORT CEILING

BOX, AND ARE NOT

THREADED ROD OR CABLE TO

BE PLUMB WITH CEILING AND FLOOR

SAFETY CABLES

ROUTE CONDUIT

(SUPPLIED BY

CUSTOMER) TO

KNOCKOUTS

AS REQUIRED

STRUCTURAL
MEMBER

ALL MOUNTING HARDWARE
SUPPLIED BY CUSTOMER

STRUCTURAL
CHANNEL

BRACKET - FSR'S
THREADED ROD
INSTALLATION KIT
(HARDWARE SUPPLIED
BY CUSTOMER)

43189 LIT1317B

3.

INSTALL 10-3/4" x 15-1/4" DROP CEILING PANEL MATERIAL
INTO DOOR OF CB-12P. BEND CAPTURE TABS OVER
PANEL TO HOLD PANEL IN PLACE.

4.

REMOVE SHELF AND MOUNT ELECTRONICS TO SHELF.
USE HOLE/SLOT PATTERN ON SHELF TO MOUNT
EQUIPMENT. ADDITIONAL HOLES MAY BE REQUIRED.
RE-INSTALL SHELF INTO CB-12P. MAKE ELECTRICAL
CONNECTIONS AS REQUIRED.

NOTE: MAXIMUM LOAD PER SHELF - 20 LBS EACH

LOOSEN SCREWS (4 PER SHELF)
TO REMOVE SHELVES

10-3/4" x 15-1/4"

DROP CEILING

PANEL MATERIAL

(SUPPLIED BY

CUSTOMER)

(4) CAPTURE TAB

TO OPEN CB-12P DOOR

LOOSEN SCREWS

NOTE: MAXIMUM PROJECTOR LOAD INCUDING MOUNTED ACCESSORIES - 50 LBS

b

a

DISCONNECT

SAFETY CABLE

TO COMPLETELY

REMOVE DOOR

5.

INSTALL PROJECTOR MOUNT PIPE INTO CB-12P. SECURE
PIPE WITH SET SCREW. FINISH INSTALLATION PER
MANUFACTURER'S PROJECTOR MOUNT INSTRUCTIONS.

DOOR IS

REMOVABLE.

(a) PUSH DOOR

UP TOWARDS

CEILING AND

(b) PUSH AWAY

FROM

PROJECTOR

PANEL MOUNT -

REVERSE

PROCEDURE

TO INSTALL

LOOSEN SHELF

SCREWS. (a) PUSH

SHELF TOWARDS

PROJECTOR

MOUNT AND (b) SHELF

WILL DROP DOWN OUT

OF CB-12P

(2) SHELF

a

b

NOTE: THE CENTER OF MASS
OF SUSPENDED EQUIP­ MENT MUST BE WITHIN
A 2.5" RADIUS OF THE
CENTER LINE OF THE
FLANGE MOUNT OF THE
CEILING BOX.

PROJECTOR MOUNT PIPE

(SUPPLIED BY CUSTOMER)

PROJECTOR MOUNT SET
SCREW ACCESS HOLE

FSR Inc.

244 Bergen Boulevard, Woodland Park, NJ 07424
Phone: [phone] - Fax: [phone]
Web: www.fsrinc.com - E-mail: [e-mail]