FSM 1700MM Tigercat Operating Manual

1700MM

Tigercat

REALISTIC RIGID

RETRACT & FLAPS INSTALLED STRONG DURABLE EPO

STABLE

SMOOTH FLYING PERFORMANCE

FMSMODEL.COM

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and
others or result in damage to the product or the property of others. This model is controlled by a radio signal subject
to interference from many sources outside your control. This interference can cause momentary loss of control so it
is advisable to always keep a safe distance in all directions around your model, as this margin will help avoid collisions
or injury.
Age Recommendation: Not for children under 14 years. This is not a toy.

·Never operate your model with low transmitter batteries.

·Always operate your model in an open area away from cars, traffic or people.

·Avoid operating your model in the street where injury or damage can occur.

·Never operate the model in populated areas for any reason.

·Carefully follow the directions and warnings for this and any optional support equipment you use (chargers,
rechargeable battery packs, etc.)

·Keep all chemicals, small parts and anything electrical out of the reach of children.

·Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed and
protected for this purpose.

·Never lick or place any part of your model in your mouth as it could cause serious injury or even death.

Lithium Polymer (Li-Po) Battery Warning
CAUTION: Always follow the manufacturer’s instructions for safe use and disposal of batteries. Fire, property
damage, or serious injury can result from the mishandling of Li-Po batteries.

By handling, charging or using a Li-Po Battery you assume all risks associated with lithium batteries.
If at any time the batteries begin to swell or balloon, discontinue use immediately!
Always store the batteries at room temperature in a dry area to extend the life of the battery. Always transport
or temporarily store the battery at a temperature range of 40-120F. Do not store the battery or model in a car or in direct

sunlight. If stored in a hot car, the battery can be damaged or even catch fire.
Never use a Ni-Mh Charger to charge Li-Po Batteries. Failure to charge the battery with a Li-Po compatible charger
may cause fire resulting in personal injury and property damage.
Never discharge Li-Po Cells below 3V.
Never leave charging batteries unattended.
Never charge damaged batteries.
Use a battery charger that is designed to safely charge the Li-Po Battery. Read the charger instructions carefully
before use. When charging the battery, make certain the battery is on a heat resistant surface. It is also highly
recommended to place the Li-Po Battery inside a fire resistant charging bag readily available at hobby shops or
online.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.
Failure to operate the product correctly can result in damage to the product, personal property and cause serious

injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and failure

to do so could result in injury or damage to the product or other property. This product is not intended for use by
children without direct adult supervision.

This manual contains instructions for safety operation and maintenance. It is essential to read and follow all the
instructions and warnings in the manual prior to assembly, setup or use, in order to operate and avoid damage or
serious injury.

Table of Contents

Introduction

3

After almost two years development, numerous tests and improvements, we have reproduced the classical highly
anticipated F7F. FMS 1700mm Tiger Cat is coming!

FMS’ warbirds are always attractive, no matter from the perspective of scaled appearance, or from excellent perfor­mance. This also applies to the Tiger Cat.

The Tiger Cat features the latest locked-rotor mode E-retract system with overcurrent protection, the refined scaled
CNC-processed metal landing gear set for resisting those not-too-perfect landings, the large size wheel set for taking
off and landing on both paved and grass surfaces. The power system utilizes twin 4250-KV440 outrunner motors,
twin 60A ESC (with 10A UBEC), providing surging power for scaled aerial combat maneuvers when coupled with a
6S 5000mAh 45C battery.

The Tiger Cat has the most scaled appearance of all our planes, with scaled plastic parts throughout the body, e.g.
landing gear door, cowl, artificial engine, and machine guns... Combine that with the detailed all-around rivets, panel
lines, pilot figure, high bright LED lamps, a CNC-processed shock-absorbed metal landing gear set, the Tiger Cat is
reproduced flawlessly. Moreover, 4 set decals in the package (blue color scheme only) allow you to make your own
Tiger Cat and stand out in your airfield.

It is more than an RC model. It is one for the collectors. Go get the FMS 1700MM “Tiger Cat” to experience its magnif­icence.

Key Features:

1.Powerful twin KV440 motors with twin Predator 60A ESC (with 10A UBEC)

2.The most accurately scaled landing gear set we have ever created

3.Super high-scale detail throughout.

4. The latest locked-rotor mode E-retract with overcurrent protection

5. Metal digital servos for excellent controlling capacity

6. Multi-connector for one-step installation, screw-together construction

7. A 62mm diameter front wheel and 84mm diameter rear wheels for taking off and landing on both paved and grass
surfaces. Large bearings in wheel hub for better performance

8. Four set decals for DIY (blue color scheme only), to be different.

Introduction
Contents of Kit
Model Assembly
Battery installation
Connectors Diagram
Get your model ready to fly
Important ESC and model information
The transmitter and model setup
Check the control throws
Check the motor rotating direction
Clevis Installation
Control Horn and Servo Arm Settings
Center of Gravity(CG)
Before flying the model
Flying your model
Troubleshooting
Spare parts list content
ESC instruction
Decal Instruction

··························································································································3

························································································································4

······················································································································5

·····································································································10

··············································································································10

······································································································11

·······················································································11

·······························································································11

·········································································································12

·····························································································12

···················································································································13

························································································13

············································································································14

···········································································································15

··················································································································16

····················································································································17

···········································································································18

·····················································································································19

···················································································································26

A.

E.

F.

H.

I.

G.

B.

C.

D.

A: Main wing (Left and Right)
B: Fuselage
C: Horizontal stabilizer (Left and Right)
D: tube
E: Nacelles (Left and Right)

F : Nose Cone
G: Machine Gun/Airspeed Head/antenna and Screws
(8-HKM3.0*16MM,8-HKM3.0*26MM)
H: Propeller and Spinner Set
I : Oil tank

Before assembly, please inspect the contents of the kit. The photo below details the contents of the kit and
labels. If any parts are missing or defective, please indentify the name or part number (refer to the spare
parts list near the end of the manual) then contact your local shop or email us: [e-mail]

Contents of Kit

4

Wingspan: 1700mm (66.9in)

Overall Length: 1484mm (58.4in)

Flying Weight: Around 5450g (192.2oz)

Motor Size: Brushless 4250-KV440*2

Wing Load: 110g/dm² ( 0.25oz/in²)

Wing Area: 49.5dm² ( 767.3sq.in)

ESC: 60A x 2 with 10A UBEC

Servo: 13g metal analog x 7, 17g metal digital x 5

5

1.Unpack the nacelles, connect the servo connectors CH5B, CH5C to the servo extensions in the wings
as shown (fig1). Connect the ESC to the motor.
Notice: Wrong plug would result in damage to motor and servo.

2.Install the nacelles to the wings and secure them in place with the screws included (fig2).

fig1

fig2

Model Assembly

HKM3.0*26

CH5B and CH5C

A B C

6

1.Slide the wing tube into the fuselage. Install the left and right wing (with nacelles on) over the wing
tube and into the wing slot of the fuselage (fig3).
Notice: The connectors on both sides should be attached precisely and firmly.

2.Secure the left and right wings to the fuselage using the screws included (fig4).

3.Connect the power lines and signal lines from the wings to the parallel power connectors (with UBEC)
and Y-harness connected to the receiver in the fuselage (fig5)

fig3

Model Assembly

HKM3.0*16

fig4

fig5

7

IMPORTANT: It is recommended to install the propeller after all system setups are completed to reduce
the chance of accidental propeller strike.

1.Screw the propellers to the adapter as shown. (fig6)

2.Install the propeller adapters (assembled with propellers) to the motor shaft and then screw with spinner
as shown. (fig7)
NOTICE: Ensure the propeller and spinner are firmly-screwed.

Apply the nose cone to the front fuselage as showed. Ensure the nose cone is on the correct side.

Required Adhesives:

Foam Safe Medium CA

fig6

fig7

fig8

Model Assembly

8

1.Slide the horizontal tail tubes into the holes in the rear of the fuselage. Ensure the shorter one is put in
front and the longer one in the back. Ensure the control horn faces down as shown.

2.Connect the elevator servo connectors to the servo extensions in the fuselage.

3.Secure the horizontal tail in place using the included screws.

1.Slide the oil tank into the rail as shown.

fig9

fig10

Model Assembly

HKM3.0*16

1.Glue the airspeed tube in place as shown. (fig11)

2.Screw the machine guns in place as shown. (fig12)

3.Glue the antenna in place as shown. (fig13)

Required Adhesives:

Foam Safe Medium CA

fig13

9

Model Assembly

fig12

fig11