FRÄNKISCHE profi-air 180 flat Installation And Operating Instructions Manual
profi-air® 180 flat connection box
Installation and operating instructions
DRAINAGE SYSTEMS
ELECTRICAL SYSTEMS
BUILDING TECHNOLOGY
INDUSTRIAL PRODUCTS
Table of contents
1 General
1.1 Introduction 3
1.2 Safety 3-4
2 Intended use 4
3 Structure 4
4 Scope of delivery 4
5 Technical data
5.1 Connection options 5
5.2 Dimensional drawing 5
5.3 Schematic wiring diagram 6
6 Wiring diagrams 6
6.1 Modbus (connection to the ventilation unit) 7
6.2 Fire/smoke alarm input 7
6.3 Humidistat input 8
6.4 Standby input 9
6.5 External fan activation input 10
6.6 Error message output 10
7 Warranty 11
8 Liability 11
9 Disposal 11
All infor mation in this p ublicatio n generally reflects the st ate of the art at th e time of printin g. Further more, consid erable care w as taken when pre paring this publication. Neverthe less, typ esetting
and trans lation error s cannot be entirely excluded . We also reser ve the right to make c hanges to our products, sp ecificati ons and other da ta. Changes may also beco me necessar y as a result of legal,
materia l-relate d or other techn ological re quirements, which cannot o r can no longe r be considered in this publi cation. For t his reason, we c annot assume a ny liability which is base d solely on the d ata
provide d in this publication. The d ecisive role w ith regard to the data on produ cts and ser vices is alway s played by the or der placed , the product a ctually purc hased and the d ocumentat ion in connec tion wit h it, or the information provid ed by our spec ialist staf f in each spec ific indivi dual case.
2
MBA profi-air 180 flat connection box
FRÄNKISCHE
1 General
The profi-air 180 flat connection box
extends the range of electric wiring
1.1 Introduction
These installation and operating instructions are intended to help you install a
fully functional profi-air 180 flat connection box and properly operate it. We recommend that you read these
instructions carefully before you com-
1.2 Safety
If used for its intended purpose, the
device is safe and reliable to operate.
The construction and design are state of
the art and comply with all relevant
options of the profi-air 180 flat ventilation unit.
mence installation. These installation
and operating instructions can also
serve as a reference for service and
maintenance work and guarantee
smooth and efficient operation.
DIN / VDE regulations and safety provisions. All safety regulations, warnings
and notices of these installation and
operating instructions have to be com-
plied with; non-compliance may result in
personal injury and/or damage to the
profi-air 180 flat connection box.
1.2.1 Safety regulations
n
Installation, connection and taking
into operation of the profi-air 180 flat
connection box must be performed
by authorised and qualified personnel only.
n
Installation of the profi-air 180 flat
connection box must be carried out
according to applicable local construction, safety and installation regulations.
n
Unauthorised changes or modifica-
tions of the profi-air 180 flat connection box are not permitted.
n
Keep these installation and operating
instructions near the device during
the entire life of the profi-air 180 flat
connection box.
MBA profi-air 180 flat connection box
3FRÄNKISCHE
1 General
1.2.3 Symbols used
Risk of personal injury
Risk of:
n
damage to equipment
n
errors while operating the device if the instructions are not complied with
correctly
n
other material damage
Additional notices
Reference to other sections and/or guidelines of the manufacturer.
Disposal instructions
2 Intended use
The profi-air 180 flat connection box is
an extension of electric connection
options for the profi-air 180 flat ventila-
3 Structure
The profi-air connection box consists of
a control board with various inputs and
outputs. The control board is incorporat-
4 Scope of delivery
n Connection box incl. 4 PG threaded
connectors
n Approx. 2.5 m of connection cable
wired / with RJ25 connector plug
to connect to the mainboard of the
profi-air 180 flat ventilation unit.
tion unit. It is connected directly to the
mainboard of the ventilation unit.
ed into a plastic housing which is
installed near the ventilation unit.
n USB cable (exclusively for the fac-
tory customer service for firmware
updates)
n Installation and operating instruc-
tions
4
MBA profi-air 180 flat connection box
FRÄNKISCHE
Loading...