FRÄNKISCHE profi-air 180 Installation And Operating Instructions Manual

DRAINAGE SYSTEMS

ELECTRICAL SYSTEMS

BUILDING TECHNOLOGY

INDUSTRIAL PRODUCTS

profi-air® 180 flat condensate pump

Installation and operating instructions

2

FRÄNKISCHE

MBA profi-air 180 flat connection box

Table of contents

1 General

2 Intended use 4

3 Structure 4

4 Technical data

4.1 Device specifications 5

4.2 Capacity diagram 5

6 Warranty 11

8 Disposal 11

7 Liability 11

1.1 Introduction 3

1.2 Safety 3 – 4

5 Installation 6

5.1 Parts overview of the entire condensate pump kit 7

5.2 Installation of the condensate pump 8 – 10

All infor mation in this p ublicatio n generally ref lects the st ate of the art at th e time of printin g. Further more, consid erable care w as taken when pre paring this pu blication. Neve rtheless , typeset ting
and trans lation error s cannot be enti rely excluded . We also reser ve the right to make c hanges to our pro ducts, specif ications an d other data. C hanges may als o become nec essary as a re sult of legal,
materia l-relate d or other technolog ical requirement s, which cann ot or can no longer be c onsidered in this pu blication. For t his reason, we c annot assume a ny liability w hich is based sole ly on the data
provide d in this public ation. The deci sive role with re gard to the data o n products and ser vices is always pl ayed by the order pla ced, the prod uct actuall y purchased and the d ocumentat ion in connec ­tion with i t, or the informatio n provided by our spe cialist staff in e ach specific ind ividual ca se.

3

FRÄNKISCHE
MBA profi-air 180 flat connection box

1 General

These installation and operating instruc­tions are intended to help you install ful­ly functional profi-air condensate pumps
and properly operate them. We recom­mend that you read these instructions
carefully before you install and use the

pump. These installation and operating
instructions can also serve as a refer­ence for service and maintenance work
and thus guarantee smooth and effi­cient operation.

If used for the intended purpose, the
device is safe and reliable to operate.
The construction and design are state of
the art and comply with all relevant

DIN / VDE regulations and safety provi­sions. All safety regulations, warnings
and notices of these installation and
operating instructions have to be com-

plied with; non-compliance might result
in personal injury and/or damage to the
profi-air condensate pump.

n

Connection and putting into opera-

tion of the profi-air condensate pump
must be performed by authorised
and qualified personnel only.

n

Installation of the profi-air condensate

pump must be carried out accord­ing to applicable local construction,
safety and installation regulations.

n

Changes or modifications of the

profi-air condensate pump are not
permitted.

n

Keep these installation and operating

instructions near the device during
the entire life of the profi-air conden­sate pump.

The profi-air condensate pump reliably
discharges condensate from the profi­air 180 flat ventilation unit. It is required

if a free condensate drain at a gradient
of at least 2 % cannot be guaranteed.
The delivery includes all necessary

parts to connect the condensate pump
to the ventilation unit.

1.1 Introduction

1.2 Safety

1.2.1 Safety regulations

4

FRÄNKISCHE

MBA profi-air 180 flat connection box

1 General

Risk of personal injury

Risk of:

n



damage to equipment

n



errors while operating the device if the instructions are not complied with
correctly

n



other material damage

Additional notices

Reference to other sections and/or guidelines of the manufacturer.

Disposal instructions

1.2.2 Symbols used

2 Intended use

3 Structure

The profi-air condensate pump has
been designed for use with the profi-air
180 flat ventilation unit only and ensures
the reliable discharge of condensate.

The profi-air condensate pump is direct­ly connected to the control of the profi­air 180 flat ventilation unit.
Depending on the operating mode of

the ventilation unit (A or B), it must
always be installed on the exhaust air /
fresh air side.

The profi-air condensate pump consists
of a pump to discharge small amounts
of condensate. The condensate pump is

controlled via a float switch. This
ensures that the pump only operates if
there is condensate. The delivery

includes all parts to connect the conden­sate pump power and condensate lines
to the ventilation unit.