Frymaster SDU 90, SDU 50 User Manual
Installation, Operation, Service and Parts Manual
(SDU 50, 90, 100 and BKSDU)
Shortening Disposal Unit
www.frymaster.com
Frymaster, a member of the Commercial Food Equipment Service Association,
recommends using CFESA Certified Technicians.
24-Hour Service Hotline 1-800-551-8633
E-mail: service@frymaster.com
MARCH 11
*8195703*
NOTICE
IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS
ENODIS EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART
PURCHASED DIRECTLY FROM FRYMASTER DEAN, OR ANY OF ITS AUTHORIZED
SERVICE CENTERS, AND/OR THE PART BEING USED IS MODIFIED FROM ITS
ORIGINAL CONFIGURATION, THIS WARRANTY WILL BE VOID. FURTHER,
FRYMASTER DEAN AND ITS AFFILIATES WILL NOT BE LIABLE FOR ANY CLAIMS,
DAMAGES OR EXPENSES INCURRED BY THE CUSTOMER WHICH ARISE DIRECTLY
OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INSTALLATION OF ANY
MODIFIED PART AND/OR PART RECEIVED FROM AN UNAUTHORIZED SERVICE
CENTER.
NOTICE
Drawings and photos used in this manual are intended to illustrate operational, cleaning
and technical procedures and may not conform to on-site management operational
procedures.
WARNING
Improper installation, adjustment, alteration, service or maintenance can cause property
damage, injury or death. Read the installation, operating and maintenance instructions
thoroughly before installing, operating or servicing this equipment.
DANGER
Hot vegetable oil will cause severe burns. Allow vegetable oil to cool to 100°F (38°C)
before transporting to the disposal site. Use extreme caution when transporting and
disposing of spent vegetable oil.
DANGER
Before each use inspect the cover to ensure the cover gasket is present and properly
placed. DO NOT use the disposal unit if this gasket is damaged or missing.
ii
Shortening Disposal Unit (SDU)
Installation, Operation, Service, and Parts Manual
TABLE OF CONTENTS
Page
1. INTRODUCTION 1
1.1 Service Information and Parts Ordering ..............................................1
1.2 Installation, Operating and Service Personnel .....................................1
1.3 Definitions ................................................................................................1
1.4 Shipping Damage Claim Procedure ......................................................2
1.5 What To Do If Your Equipment Arrives Damaged .............................2
2. ASSEMBLY AND OPERATION ..........................................................2
2.1 Equipment Description ...........................................................................2
2.2 Equipment Assembly ..............................................................................3
2.3 Equipment Operation .............................................................................3
2.4 Cleaning ....................................................................................................5
3. SERVICE PROCEDURES .....................................................................5
3.1 General .....................................................................................................5
3.2 Replacing Worn or Damaged O-Rings ..................................................5
3.3 Replacing Worn Pump Vanes and/or Pump Shaft Seal ......................5
4. PARTS LIST ............................................................................................7
iii
SHORTENING DISPOSAL UNIT
(SDU 100, 90 50, AND BKSDU)
INSTALLATION, OPERATION, SERVICE AND PARTS
1. INTRODUCTION
1.1 Service Information and Parts Ordering
Included with the unit when shipped from the factory is a list of Factory Authorized Servicers
(FAS). Refer to this list to find the FAS nearest you. If you do not have access to this list, contact
the Frymaster Technical Service Department at 1-800-551-8633 or 1-318-865-1711.
Service information may be obtained by contacting your local FAS. Information may also be
obtained by calling the Frymaster Technical Service Department at 1-800-551-8633 or 1-318-8651711 or by e-mail: service@frymaster.com. In order to assist you as quickly as possible, the FAS or
Service Department representative requires certain information about your equipment. The
information is printed on a data plate located on the tank cover. When requesting service, please
have the following information ready:
Model Number:
Serial Number:
In addition to the model number, and serial number, please be prepared to describe the nature of the
problem and have ready any other information that you think may be helpful in solving your
problem. Parts orders may be placed directly with your local FAS or distributor. When ordering
parts, the following information is required:
Model Number:
Serial Number:
Item Part Number:
Quantity Needed:
RETAIN AND STORE THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE.
1.2 Installation, Operating and Service Personnel
Installation, Operating, and Service information for this equipment has been prepared for use by
qualified and/or authorized personnel only, as defined in Section 1.3.
1.3 Definitions
QUALIFIED AND/OR AUTHORIZED OPERATING PERSONNEL
Qualified/authorized operating personnel are those who have carefully read the information in this
manual and have familiarized themselves with the equipment functions, or who have had previous
experience with the operation of the equipment covered in this manual.
QUALIFIED SERVICE PERSONNEL
Qualified service personnel are those who are familiar with this equipment and who have been
authorized by Frymaster L.L.C. to perform service on equipment manufactured by Frymaster. All
authorized service personnel are required to be equipped with a complete set of service and parts
1
manuals, and to stock a minimum amount of parts for Frymaster equipment. A list of Factory
Authorized Service Centers (FASs) was included with this equipment when shipped from the
factory. Unless specifically indicated otherwise in this manual, failure to use qualified service
personnel will void the Frymaster Warranty on this equipment.
1.4 Shipping Damage Claim Procedure
This equipment was carefully inspected and packed before leaving the factory. The transportation
company assumes full responsibility for safe delivery upon acceptance of the equipment for
transport.
1.5 What to Do If Your Equipment Arrives Damaged
1. File a claim for damages immediately, regardless of the extent of damages.
2. Inspect for and record all visible loss or damage and ensure that this information is noted on
the freight bill or express receipt and is signed by the person making the delivery.
3. Concealed loss or damage that was unnoticed until the equipment was unpacked should be
recorded and reported to the freight company or carrier immediately upon discovery. A
concealed damage claim must be submitted within 15 days of the date of delivery. Ensure that
the shipping container is retained for inspection.
FRYMASTER DOES NOT ASSUME RESPONSIBILITY
FOR DAMAGE OR LOSS INCURRED IN TRANSIT.
2. ASSEMBLY AND OPERATION
2.1 Equipment Description
The Shortening Disposal Unit (SDU) is designed for the safe transportation of used shortening or
cooking oil from the kitchen to a disposal container. There are three sizes –SDU 50 (50 lbs./23 kg),
SDU 90 (90 lbs./41 kg) and SDU 100 (100 lbs./45kg). All sizes are similar in construction and
operation. The units consist of a tank and a heavy-duty manual pump. All models are equipped with
6 " (150 mm) wheels.
The BKSDU is equipped with a 120VAC or 240VAC tank heater to prevent solid shortening from
solidifying prior to disposal. The BKSDU is equipped with a receptacle that accepts a three-prong,
grounded plug for protection against shock hazard. The power cord should be plugged directly into
a properly grounded, three-hole wall or floor receptacle. Do not cut off, remove, or otherwise
bypass the grounding prong on the power cord plug. CAUTION: Risk of fire and electric shock.
Replace only with manufacturer’s cord set, part number 8071224 for 120V or part number
106-4697 for 240V.
With the cover open, the top of the tank is 9¾ inches (248 mm) above the floor, permitting it to be
positioned directly beneath the drains of most fryers.
2
Loading...