Fronius prints on elemental chlorine free paper (ECF) sourced from certified sustainable forests (FSC).
/ Perfect Charging / Perfect Welding / Solar Energy
RC Panel Pro
Operating instructions
EN-US
42,0426,0282,EA 003-22112021
General
(1)
(2)
(3)
EN-US
Safety
Incorrect operation and incorrectly performed work can cause serious injury and
damage to property.
All work listed in this document may only be performed by trained specialist personnel.
All functions described in this document may only be used by trained specialist personnel. All work and functions described may only be performed and used once the following documents have been read and understood in full:
▶
▶
Device Concept The remote control has the same functionality as the power source’s control panel. A
precise description of the possible settings can be found in the power source's Operating
Instructions.
To be able to use the remote control, the welding system must have a TPS/i power
source.
WARNING!
This Document
All Operating Instructions for system components, especially the safety rules
NOTE!
Scope of Supply
NOTE!
Because of firmware updates, certain functions may be available that are not described in these Operating Instructions or vice versa.
(1) Remote control
(2) TPS/i Key Card
(3) This document
Technical data
Supply voltage + 24 V DC
Protection class IP 44
Marks of conformity CE, FCC
3
Dimensions (l x w x h) 260 x 220 x 60 mm
10.24 x 8.66 x 2.36 in.
Notes on Radio
Certification
The device is equipped with a wireless module.
Wireless modules in the USA require FCC certification:
FCC
This device complies with Section 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
FCC ID: QKWSPB209A
Industry Canada RSS
This device complies with Industry Canada license-exempt RSS standards. Operation
is subject to the following conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
IC: 12270A-SPB209A
Unless otherwise expressly permitted by the manufacturer, changes or modifications to
the wireless module are not allowed and lead to a loss of the right of use of the device by
the user.
NOTE!
This device has been tested and meets the limit values for a Class A digital device
as per Section 15 of the FCC Rules.
These limit values are designed to provide adequate protection against harmful interference when the device is operated in a commercial environment. This device generates,
uses and can emit high-frequency energy, and if it is not installed and used as per the
Operating Instructions, it may cause harmful interference to wireless communication. Operating this device in a residential area may lead to harmful interference, which the user
must rectify at their own cost
4
Controls, connections and indicators
(1)
(2)
(3)
(4)
(1)
(5)
(6)
(7)
Keys and Symbols
(1) Control dial with rotary/push button function
For selecting elements, setting values and scrolling through lists
EN-US
(2) Special function button
For selecting special functions depending on configuration
(3) Gas-test button
For setting the required amount of gas on the gas pressure regulator.
After pressing the gas-test button, gas is emitted for 30 seconds. Pressing the
button again ends the process early
(4) Touch display
(5) Wire-threading button
For threading the wire electrode into the torch hosepack without gas or current
(6) Wire-return button
For retracting the wire electrode without gas or current
NOTE!
Only retract the wire electrode a small amount at a time, to avoid the wire electrode becoming entangled during retraction.
(7) Reading zone for TPS/i Key Card and TPS/i Key Fob
For locking/unlocking the remote control using the TPS/i Key Card and TPS/i
Key Fob
5
(8)
(9)
(8) Pivoting mounting and positioning bracket
(9) USB port
For connecting USB flash drives (service dongle, license key, etc.)
6
Installation and Startup
EN-US
Mount Remote
Control on a
Handle Tube
CAUTION!
Danger of injury and damage to property due to falling remote control.
Always secure the remote control against falling.
1
Connect Remote
Control to System Components
1
7
Fronius International GmbH
Froniusstraße 1
4643 Pettenbach
Austria
contact@fronius.com
www.fronius.com
Under www.fronius.com/contact you will find the adresses
of all Fronius Sales & Service Partners and locations.
spareparts.fronius.com
SPAREPARTS
ONLINE
Loading...