Acerios
Settings before plasma process starts | Access/exit the Setup Menu
1. Select the operating mode
2-step mode:
Start: I
Stop: t
start
down
- tup - I
- I
end
main
4-step mode:
Start: I
Stop: tup - I
Start: t
start
down
main
- I
end
Stop: End
Job Mode
2. Set the process parameters
2
1 1
1
Press button to select the desired
parameter
Turn selection dial to set the
2
parameter
Process parameters
Starting current
I
start
t
Up-Slope
up
I
Main current
main
Down-Slope
t
down
I
Final current
end
Job number
Electrode diameter
Access / exit the Setup Menu
2
1
Select 2-step or 4-step mode
Press and hold
2
Press
3
Access the Gas Menu
1
Press and hold
2
Exit the Setup Menu / Gas Menu
1
Press
Press
1
3
Bedienungsanleitung:
manuals.fronius.com/
42,0426,0339,EA 001-16072019
html/4204260339
Acerios
Settings before plasma process starts | Access/exit the Setup Menu
1. Select the operating mode
2-step mode:
Start: I
Stop: t
start
down
- tup - I
- I
end
main
4-step mode:
Start: I
Stop: tup - I
Start: t
start
down
main
- I
end
Stop: End
Job Mode
2. Set the process parameters
2
1 1
1
Press button to select the desired
parameter
Turn selection dial to set the
2
parameter
Process parameters
Starting current
I
start
t
Up-Slope
up
I
Main current
main
Down-Slope
t
down
I
Final current
end
Job number
Electrode diameter
Access / exit the Setup Menu
2
Select 2-step or 4-step mode
1
Press and hold
2
Press
3
Access the Gas Menu
1
Press and hold
2
Exit the Setup Menu / Gas Menu
1
Press
Press
1
3
42,0426,0339,EA 001-16072019
Bedienungsanleitung:
manuals.fronius.com/
html/4204260339
Acerios
Access / exit the Job Correction Menu | Description of Setup parameters
Access / exit the Job Correction Menu
2
1
Select Job Mode
Press and hold
2
3
Press
Exit the Job Correction Menu
1
Press
Setup Menu
Pulse frequency
Dutycycle
Base current
Starting current time
Final current time
1)
1) 2)
1) 2)
1)
1)
Reset plasma system
2nd Level Setup Menu
3
1
2nd Level Setup Menu
Cooling unit controls
Cooling time
High Frequency time
Delayed ignition for immediate high
frequency start
Gas correction
1) 3)
Plasma system resistance
Plasma system inductance
Ignition time out
Gas Menu
Gas pre-flow time
1)
Gas post-flow time at minimum
process current
1)
Gas post-flow time at maximum
process current
1)
Set value for gas flow
Gas purging
Job Correction Menu
Diameter of electrode
Starting current
Up-Slope
Main current
Down-Slope
Final current
Job-Slope
Operating mode selection
I
correction range
main
1) 3)
Arc break monitoring
1)
The parameter is also available in the Job Correction Menu
Country-specific setting
External parameter
Main current changeover
2)
Only available if parameter "F-P" (pulse frequency) is
not "oFF"
3)
Only available if an external gas regulator is connected
SAFETY
Before working with the device, ensure that you have read and understood all the documents provided in hard copy and online.
This document does not describe all the functions of the device. For a complete description of the device, refer to the Operating Instructions.
Acerios
Access / exit the Job Correction Menu | Description of Setup parameters
Access / exit the Job Correction Menu
2
1
Select Job Mode
Press and hold
2
Press
3
Exit the Job Correction Menu
1
Press
1
Setup Menu
Pulse frequency
Dutycycle
Base current
Starting current time
Final current time
Reset plasma system
2nd Level Setup Menu
3
2nd Level Setup Menu
Cooling unit controls
Cooling time
High Frequency time
Delayed ignition for immediate high
frequency start
Gas correction
Plasma system resistance
Plasma system inductance
Ignition time out
Arc break monitoring
Country-specific setting
External parameter
Main current changeover
1)
1) 2)
1) 2)
1)
1)
1) 3)
Gas Menu
Gas pre-flow time
1)
Gas post-flow time at minimum
process current
1)
Gas post-flow time at maximum
process current
Set value for gas flow
1)
1) 3)
Gas purging
Job Correction Menu
Diameter of electrode
Starting current
Up-Slope
Main current
Down-Slope
Final current
Job-Slope
Operating mode selection
I
correction range
main
1)
The parameter is also available in the Job Correction Menu
2)
Only available if parameter "F-P" (pulse frequency) is
not "oFF"
3)
Only available if an external gas regulator is connected
SAFETY
Before working with the device, ensure that you have read and understood all the documents provided in hard copy and online.
This document does not describe all the functions of the device. For a complete description of the device, refer to the Operating Instructions.
Loading...