Fronius prints on elemental chlorine free paper (ECF) sourced from certified sustainable forests (FSC).
/ Perfect Charging / Perfect Welding / Solar Energy
OPT/i WF Tower Zusatzmodule
OPT/i WF Tower additional modules
Installationsanleitung
DE
Roboter-Option
Installation instructions
Robot option
EN-US
42,0410,2538002-23062021
Sicherheit
DE
Sicherheit
WARNUNG!
Gefahr durch Fehlbedienung und fehlerhaft durchgeführte Arbeiten.
Schwerwiegende Personen- und Sachschäden können die Folge sein.
Alle in diesem Dokument beschriebenen Arbeiten und Funktionen dürfen nur von
▶
geschultem Fachpersonal ausgeführt werden.
Dieses Dokument lesen und verstehen.
▶
Sämtliche Bedienungsanleitungen der Systemkomponenten, insbesondere Sicher-
▶
heitsvorschriften lesen und verstehen.
WARNUNG!
Gefahr durch elektrischen Strom.
Schwere Verletzungen oder Tod können die Folge sein.
Vor Beginn der Arbeiten alle beteiligten Geräte und Komponenten ausschalten und
▶
von Stromnetz trennen.
Alle beteiligten Geräte und Komponenten gegen Wiedereinschalten sichern.
▶
3
Zusatzmodul für WF 30i R /TWIN
Lieferumfang
Zusatzmodul für WF 30i R /TWIN
Zusatzmodul für
WF 30i R /TWIN
auf OPT/i WF
Tower festschrauben
WF 30i Twin festschrauben
1
1
Die zwei Montagevorrichtungen so festschrauben, dass die darauf vorhandenen
Pfeile in die Richtung zeigen, in welche die
Drahtelektrode durch den Drahtvorschub
gefördert wird.
4
2
Den Drahtvorschub so auf dem Zusatzmodul festschrauben, dass die Drahtelektrode in die Richtung gefördert wird, die
der Pfeil auf dem Zusatzmodul anzeigt.
DE
Sicherheitsmaßnahmen
nach erfolgter
Montage
1
Gefahr durch abrutschende Komponenten.
Werden alle 16 Schrauben gelöst, rutscht
der obere Teil von OPT/i WF Tower ungebremst nach unten. Dadurch können
schwerwiegende Personen- und
Sachschäden entstehen.
▶
▶
WARNUNG!
Vor dem Lösen aller Schrauben, den
Drahtvorschub demontieren.
Sicherstellen, dass während des
Lösens der Schrauben der obere Teil
von OPT/i WF Tower von einer zweiten Person gehalten wird.
5
Zusatzmodul Drahtspulen-Aufnahme
Lieferumfang
Zusatzmodul Drahtspulen-Aufnahme
Drahtspulen-Aufnahme festschrauben
12
3
Sicherstellen, dass die 8 Schrauben
M8x16mm in die Muttern von OPT/i WF
Tower geschraubt werden.
6
4
DE
7
Zusatzmodul Mounting WF R Tower
Lieferumfang
Zusatzmodul Mounting WF R Tower
Zusatzmodul
Mounting WF R
Tower und WF
15i/25i/30i oder
SB 500i festschrauben
1
2
8
34
* Die Schrauben noch nicht festziehen
5
DE
6
9
Sicherheitsmaßnahmen
nach erfolgter
Montage
1
Gefahr durch abrutschende Komponenten.
Werden alle 16 Schrauben gelöst, rutscht
der obere Teil von OPT/i WF Tower ungebremst nach unten. Dadurch können
schwerwiegende Personen- und
Sachschäden entstehen.
▶
▶
WARNUNG!
Vor dem Lösen aller Schrauben, den
Drahtvorschub / die Splitbox demontieren.
Sicherstellen, dass während des
Lösens der Schrauben der obere Teil
von OPT/i WF Tower von einer zweiten Person gehalten wird.
10
Safety
Safety
WARNING!
Danger from incorrect operation and work that is not carried out properly.
This can result in severe personal injury and damage to property.
All the work and functions described in this document must only be carried out by
▶
trained and qualified personnel.
Read and understand this document.
▶
Read and understand all the Operating Instructions for the system components,
▶
especially the safety rules.
WARNING!
Danger from electrical current.
This may result in serious injuries or death.
Before starting work, switch off all devices and components involved, and discon-
▶
nect them from the grid.
Secure all devices and components involved so they cannot be switched back on.
▶
EN-US
11
Additional module for WF 30i R /TWIN
Scope of supply
Additional module for WF 30i R /TWIN
Screwing the
additional
module for the
WF 30i R /TWIN
to the OPT/i WF
Tower
Screwing on the
WF 30i Twin
1
1
Screw on the two mounting fixtures so that
the arrows on them point in the direction in
which the wire electrode is conveyed by
the wirefeeder.
12
2
Screw the wirefeeder onto the additional
module in such a way that the wire electrode is fed in the direction indicated by
the arrow on the additional module.
EN-US
Safety measures
after installation
1
Danger from sliding components.
When all 16 screws are loosened, the
upper part of the OPT/i WF Tower slides
down unbraked. This can cause serious
injury and damage to property.
▶
▶
WARNING!
Before loosening all screws, remove
the wirefeeder.
Make sure that the upper part of the
OPT/i WF Tower is being held by a
second person while loosening the
screws.
13
Additional module for wirespool holder
Scope of supply
Additional module for wirespool holder
Screwing on the
wirespool holder
12
3
Ensure that the 8 M8x16mm screws are
screwed into the nuts of the OPT/i WF
Tower.
14
4
EN-US
15
Additional module for Mounting WF R Tower
Scope of supply
Additional module for Mounting WF R Tower
Screwing on the
additional
module for Mounting WF R Tower
and WF
15i/25i/30i or SB
500i
1
2
16
34
* Do not tighten the screws yet
5
EN-US
6
17
Safety measures
after installation
1
Danger from sliding components.
When all 16 screws are loosened, the
upper part of the OPT/i WF Tower slides
down unbraked. This can cause serious
injury and damage to property.
▶
▶
WARNING!
Before loosening all screws, remove
the wirefeeder / the Splitbox.
Make sure that the upper part of the
OPT/i WF Tower is being held by a
second person while loosening the
screws.
18
EN-US
19
FRONIUS INTERNATIONAL GMBH
Froniusstraße 1
A-4643 Pettenbach
AUSTRIA
contact@fronius.com
www.fronius.com
Under www.fronius.com/contact you will find the addresses
of all Fronius Sales & Service Partners and locations
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.