Fronius TransTig 2200, TransTig 2500, TransTig 3000, TransTig 4000, TransTig 5000 Operating Instructions Manual
...
Fronius prints on elemental chlorine free paper (ECF) sourced from certified sustainable forests (FSC).
/ Perfect Charging / Perfect Welding / Solar Energy
42,0426,0027,EN 018-23022017
TransTig 2200
TransTig 2500 / 3000
TransTig 4000 / 5000
MagicWave 1700 / 2200
MagicWave 2500 / 3000
MagicWave 4000 / 5000
Operating Instructions
Spare parts list
TIG Power source
EN
2
3
EN
Dear reader,
Introduction Thank you for the trust you have placed in our company and congratulations on buying this
high-quality Fronius product. These instructions will help you familiarise yourself with the
product. Reading the instructions carefully will enable you to learn about the many different
features it has to offer. This will allow you to make full use of its advantages.
Please also note the safety rules to ensure greater safety when using the product. Careful
handling of the product will repay you with years of safe and reliable operation. These are
essential prerequisites for excellent results.
4
5
EN
Contents
Safety rules ................................................................................................................................................ 9
Explanation of safety symbols .............................................................................................................. 9
General ................................................................................................................................................. 9
Proper use ............................................................................................................................................ 10
Environmental conditions...................................................................................................................... 10
Obligations of the operator.................................................................................................................... 10
Obligations of personnel ....................................................................................................................... 11
Mains connection .................................................................................................................................. 11
Protecting yourself and others .............................................................................................................. 11
Noise emission values .......................................................................................................................... 12
Danger from toxic gases and vapours .................................................................................................. 12
Danger from flying sparks ..................................................................................................................... 13
Risks from mains current and welding current...................................................................................... 13
Meandering welding currents................................................................................................................ 14
EMC Device Classifications .................................................................................................................. 14
EMC measures ..................................................................................................................................... 15
EMF measures...................................................................................................................................... 15
Specific hazards.................................................................................................................................... 15
Factors affecting welding results........................................................................................................... 17
Danger from shielding gas cylinders..................................................................................................... 17
Safety measures at the installation location and during transport ........................................................ 17
Safety measures in normal operation ................................................................................................... 18
Commissioning, maintenance and repair.............................................................................................. 19
Safety inspection................................................................................................................................... 19
Disposal ................................................................................................................................................ 19
Safety symbols...................................................................................................................................... 20
Data protection...................................................................................................................................... 20
Copyright............................................................................................................................................... 20
General information 21
General ...................................................................................................................................................... 23
Device concept ..................................................................................................................................... 23
Functional principle ............................................................................................................................... 24
Field of application ................................................................................................................................ 24
Warning notices on the device.............................................................................................................. 25
System components .................................................................................................................................. 26
General ................................................................................................................................................. 26
Overview ............................................................................................................................................... 26
Control elements and connections 27
Description of the control panels................................................................................................................ 29
General ................................................................................................................................................. 29
Safety.................................................................................................................................................... 29
Overview ............................................................................................................................................... 29
MagicWave control panel........................................................................................................................... 30
MagicWave control panel...................................................................................................................... 30
TransTig control panel ............................................................................................................................... 34
TransTig control panel .......................................................................................................................... 34
Key combinations - special functions......................................................................................................... 38
General ................................................................................................................................................. 38
Displaying the software version, operating time and coolant flow ........................................................ 38
Connections, switches and mechanical components ................................................................................ 39
MagicWave1700 / 2200 ........................................................................................................................ 39
MagicWave2500 / 3000 ........................................................................................................................ 40
MagicWave4000 / 5000 ........................................................................................................................ 41
TransTig 2200....................................................................................................................................... 42
TransTig2500 / 3000............................................................................................................................. 43
TransTig4000 / 5000............................................................................................................................. 44
6
Installation and commissioning 45
Minimum equipment needed for welding task............................................................................................ 47
General ................................................................................................................................................. 47
TIG AC welding..................................................................................................................................... 47
TIG DC welding..................................................................................................................................... 47
MMA welding ........................................................................................................................................ 47
Before installation and commissioning....................................................................................................... 48
Safety.................................................................................................................................................... 48
Utilisation for intended purpose ............................................................................................................ 48
Setup regulations .................................................................................................................................. 48
Mains connection .................................................................................................................................. 48
Generator-powered operation (MW 1700 / 2200, TT2200)................................................................... 49
Connecting up the mains cable on US power sources .............................................................................. 50
General ................................................................................................................................................. 50
Stipulated mains cables and strain-relief devices ................................................................................. 50
Safety.................................................................................................................................................... 50
Connecting the mains cable.................................................................................................................. 50
Replacing the strain-relief device.......................................................................................................... 51
Start-up ...................................................................................................................................................... 53
Safety.................................................................................................................................................... 53
Remarks on the cooling unit ................................................................................................................. 53
General ................................................................................................................................................. 53
Connecting the gas cylinder.................................................................................................................. 53
Establishing a ground (earth) connection to the workpiece .................................................................. 54
Connecting the welding torch................................................................................................................ 54
Welding 55
TIG modes ................................................................................................................................................. 57
Safety.................................................................................................................................................... 57
Symbols and their explanations ............................................................................................................ 57
2-step mode .......................................................................................................................................... 58
4-step mode .......................................................................................................................................... 58
Special 4-step mode: variant 4 ............................................................................................................. 59
Cap shaping and cap overloading ............................................................................................................. 60
Cap shaping.......................................................................................................................................... 60
TIG welding................................................................................................................................................ 61
Safety.................................................................................................................................................... 61
Welding parameters.............................................................................................................................. 61
Preparation ........................................................................................................................................... 62
TIG welding........................................................................................................................................... 62
Igniting the arc ........................................................................................................................................... 64
General ................................................................................................................................................. 64
Igniting the arc using high frequency(HF ignition)................................................................................. 64
Touchdown ignition ............................................................................................................................... 65
End of welding ...................................................................................................................................... 66
Special functions and options .................................................................................................................... 67
Arc break watchdog function................................................................................................................. 67
Ignition time-out function....................................................................................................................... 67
Tacking function.................................................................................................................................... 67
MMA welding ............................................................................................................................................. 69
Safety.................................................................................................................................................... 69
Preparation ........................................................................................................................................... 69
Manual metal arc welding ..................................................................................................................... 69
Hotstart function.................................................................................................................................... 70
Anti-stick function.................................................................................................................................. 71
Setup settings 73
The Setup menu ........................................................................................................................................ 75
General ................................................................................................................................................. 75
Overview ............................................................................................................................................... 75
7
EN
Shielding gas setup menu.......................................................................................................................... 76
General ................................................................................................................................................. 76
Opening the Protective gas shield set-up menu ...................................................................................76
Changing welding parameters .............................................................................................................. 76
Exiting the set-up menu ........................................................................................................................ 76
Welding parameters in the Protective gas shield set-up menu............................................................. 76
TIG setup menu ......................................................................................................................................... 78
Opening the TIG set-up menu .............................................................................................................. 78
Changing welding parameters .............................................................................................................. 78
Exiting the set-up menu ........................................................................................................................ 78
Welding parameters in the TIG set-up menu ........................................................................................ 78
Rod electrode setup menu......................................................................................................................... 81
Open the rod electrode set-up menu .................................................................................................... 81
Changing welding parameters .............................................................................................................. 81
Exiting the set-up menu ........................................................................................................................ 81
Welding parameters in the rod electrode set-up menu ......................................................................... 81
Rod electrode setup menu: level 2 ............................................................................................................ 83
Opening the rod electrode set-up menu level 2 .................................................................................... 83
Changing welding parameters .............................................................................................................. 83
Exiting the rod electrode set-up menu - level 2..................................................................................... 83
Welding parameters in the rod electrode set-up menu level 2.............................................................. 83
Troubleshooting and maintenance 87
Troubleshooting ......................................................................................................................................... 89
General ................................................................................................................................................. 89
Safety.................................................................................................................................................... 89
Displayed service codes ....................................................................................................................... 89
Power source - troubleshooting ............................................................................................................ 92
Care, maintenance and disposal ............................................................................................................... 94
General ................................................................................................................................................. 94
Safety.................................................................................................................................................... 94
At every start-up.................................................................................................................................... 94
Every 2 months ..................................................................................................................................... 94
Every 6 months ..................................................................................................................................... 94
Disposal ................................................................................................................................................ 95
Appendix 97
Technical data............................................................................................................................................ 99
Special voltages.................................................................................................................................... 99
MagicWave1700 / 2200 ........................................................................................................................ 99
MagicWave2500 / 3000 ........................................................................................................................ 100
MagicWave 2500 / 3000 MV................................................................................................................. 100
MagicWave4000 / 5000 ........................................................................................................................ 101
MagicWave 4000 / 5000 MV................................................................................................................. 102
TransTig 2200....................................................................................................................................... 103
TransTig2500 / 3000............................................................................................................................. 104
TransTig 2500 / 3000 MV ..................................................................................................................... 105
TransTig4000 / 5000............................................................................................................................. 106
TransTig 4000 / 5000 MV ..................................................................................................................... 107
Explanation of footnotes ....................................................................................................................... 107
Terms and abbreviations used................................................................................................................... 108
General ................................................................................................................................................. 108
Terms and abbreviations A - F.............................................................................................................. 108
Terms and abbreviations G - H............................................................................................................. 108
Terms and abbreviations I - U............................................................................................................... 109
Spare parts and circuit diagrams 111
Spare parts list: TT 800 / 2200 Job, MW 1700 / 2200 Job, TT 2200, MW 1700 / 2200
............................. 112
Spare parts list: TransTig / MagicWave 2500 / 3000 ................................................................................. 114
Spare parts list: TransTig 4000 / 5000....................................................................................................... 116
Spare parts list: MagicWave 4000 / 5000 .................................................................................................. 118
8
Circuit diagrams: MagicWave 1700 ........................................................................................................... 121
Circuit diagrams: MagicWave 2200 ........................................................................................................... 122
Circuit diagrams: MagicWave 2500 / MagicWave 2500 MV ...................................................................... 123
Circuit diagrams: MagicWave 3000 / MagicWave 3000 MV ...................................................................... 124
Circuit diagrams: MagicWave 4000 / MagicWave 5000 ............................................................................ 125
Circuit diagrams: MagicWave 4000 MV / MagicWave 5000 MV................................................................ 127
Circuit diagrams: TransTig 2200................................................................................................................ 130
Circuit diagrams: TransTig 2500 / TransTig 2500 MV ............................................................................... 131
Circuit diagrams: TransTig 3000 / TransTig 3000 MV ............................................................................... 132
Circuit diagrams: TransTig 4000 / TransTig 5000...................................................................................... 133
Circuit diagrams: TransTig 4000 MV / TransTig 5000 MV......................................................................... 134
9
EN
Safety rules
Explanation of
safety symbols
If you see any of the symbols depicted in the "Safety rules" chapter, special care is required.
General
DANGER! Indicates immediate and real danger. If it is not avoided, death or se-
rious injury will result.
WARNING! Indicates a potentially dangerous situation. Death or serious injury
may result if appropriate precautions are not taken.
CAUTION! Indicates a situation where damage or injury could occur. If it is not
avoided, minor injury and/or damage to property may result.
NOTE! Indicates a risk of flawed results and possible damage to the equipment.
IMPORTANT! Indicates tips for correct operation and other particularly useful information.
It does not indicate a potentially damaging or dangerous situation.
The device is manufactured using state-of-the-art technology and according
to recognised safety standards. If used incorrectly or misused, however, it can
cause:
- injury or death to the operator or a third party,
- damage to the device and other material assets belonging to the operating company,
- inefficient operation of the device.
All persons involved in commissioning, operating, maintaining and servicing
the device must:
- be suitably qualified,
- have sufficient knowledge of welding and
- read and follow these operating instructions carefully.
The operating instructions must always be at hand wherever the device is being used. In addition to the operating instructions, attention must also be paid
to any generally applicable and local regulations regarding accident prevention and environmental protection.
All safety and danger notices on the device
- must be in a legible state,
- must not be damaged,
- must not be removed,
- must not be covered, pasted or painted over.
For the location of the safety and danger notices on the device, refer to the
section headed "General" in the operating instructions for the device.
Before switching on the device, rectify any faults that could compromise safety.
This is for your personal safety!
10
Proper use
Environmental
conditions
Obligations of the
operator
The device is to be used exclusively for its intended purpose.
The device is intended solely for the welding processes specified on the rating
plate.
Any use above and beyond this purpose is deemed improper. The manufacturer shall not be held liable for any damage arising from such usage.
Proper use includes:
- carefully reading and following all the instructions given in the operating
instructions
- studying and obeying all safety and danger notices carefully
- performing all stipulated inspection and maintenance work.
Never use the device for the following purposes:
- Thawing out pipes
- Charging batteries
- Starting engines
The device is designed for use in industry and the workshop. The manufacturer accepts no responsibility for any damage caused through use in a domestic
setting.
The manufacturer likewise accepts no liability for inadequate or incorrect results.
Operation or storage of the device outside the stipulated area will be deemed
as not in accordance with the intended purpose. The manufacturer shall not
be held liable for any damage arising from such usage.
Ambient temperature range:
- during operation: -10 °C to + 40 °C (14 °F to 104 °F)
- during transport and storage: -20 °C to +55 °C (-4 °F to 131 °F)
Relative humidity:
- up to 50% at 40 °C (104 °F)
- up to 90% at 20 °C (68 °F)
The surrounding air must be free from dust, acids, corrosive gases or substances, etc.
Can be used at altitudes of up to 2000 m (6561 ft. 8.16 in.)
The operator must only allow persons to work with the device who:
- are familiar with the fundamental instructions regarding safety at work and
accident prevention and have been instructed in how to use the device
- have read and understood these operating instructions, especially the
section "safety rules", and have confirmed as much with their signatures
- are trained to produce the required results.
Checks must be carried out at regular intervals to ensure that operators are
working in a safety-conscious manner.
11
EN
Obligations of
personnel
Mains connection
Protecting yourself and others
Before using the device, all persons instructed to do so undertake:
- to observe the basic instructions regarding safety at work and accident
prevention
- to read these operating instructions, especially the "Safety rules" section
and sign to confirm that they have understood them and will follow them.
Before leaving the workplace, ensure that people or property cannot come to
any harm in your absence.
Devices with a higher rating may affect the energy quality of the mains due to
their current consumption.
This may affect a number of types of device in terms of:
- connection restrictions
- criteria with regard to the maximum permissible mains impedance
*)
- criteria with regard to the minimum short-circuit power requirement
*)
*)
at the interface with the public grid
see Technical Data
In this case, the plant operator or the person using the device should check
whether the device may be connected, where appropriate by discussing the
matter with the power supply company.
NOTE! Ensure that the mains connection is earthed properly
Persons involved with welding expose themselves to numerous risks, e.g.:
- flying sparks and hot pieces of metal
- arc radiation, which can damage eyes and skin
- hazardous electromagnetic fields, which can endanger the lives of those
using cardiac pacemakers
- risk of electrocution from mains current and welding current
- greater noise pollution
- harmful welding fumes and gases
Anyone working on the workpiece while welding is in progress must wear suitable protective clothing with the following properties:
- flame-resistant
- insulating and dry
- covers the whole body, is undamaged and in good condition
- safety helmet
- trousers with no turn-ups
12
Noise emission
values
Danger from toxic
gases and vapours
Protective clothing refers to a variety of different items. Operators should:
- protect eyes and face from UV rays, heat and sparks using a protective
visor and regulation filter.
- wear regulation protective goggles with side protection behind the protective visor.
- wear stout footwear that provides insulation even in wet conditions.
- protect the hands with suitable gloves (electrically insulated and providing
protection against heat).
- wear ear protection to reduce the harmful effects of noise and to prevent
injury.
Keep all persons, especially children, out of the working area while any devices are in operation or welding is in progress. If, however, there are people in
the vicinity,
- make them aware of all the dangers (risk of dazzling by the arc, injury
from flying sparks, harmful welding fumes, noise, possible risks from
mains current and welding current, etc.),
- provide suitable protective equipment or
- erect suitable safety screens/curtains.
The device generates a maximum sound power level of <80 dB(A) (ref. 1pW)
when idling and in the cooling phase following operation at the maximum permissible operating point under maximum rated load conditions according to
EN 60974-1.
It is not possible to provide a workplace-related emission value during welding
(or cutting) as this is influenced by both the process and the environment. All
manner of different welding parameters come into play, including the welding
process (MIG/MAG, TIG welding), the type of power selected (DC or AC), the
power range, the type of weld metal, the resonance characteristics of the
workpiece, the workplace environment, etc.
The fumes produced during welding contain harmful gases and vapours.
Welding fumes contain substances that may, under certain circumstances,
cause birth defects or cancer.
Keep your face away from welding fumes and gases.
Fumes and hazardous gases
- must not be breathed in
- must be extracted from the working area using appropriate methods.
Ensure an adequate supply of fresh air with a ventilation rate of at least 20 m³/
hour.
Otherwise, a protective mask with an air supply must be worn.
Close the shielding gas cylinder valve or main gas supply if no welding is taking place.
If there is any doubt about whether the extraction capacity is sufficient, the
measured toxic emission values should be compared with the permissible limit
values.
Amongst others, the following components are responsible for the degree of
toxicity of welding fumes:
- Metals used for the workpiece
- Electrodes
- Coatings
- Cleaners, degreasers, etc.
13
EN
Danger from flying sparks
Risks from mains
current and welding current
The relevant material safety data sheets and manufacturer's specifications for
the listed components should therefore be studied carefully.
Flammable vapours (e.g. solvent fumes) should be kept away from the arc's
radiation area.
Flying sparks may cause fires or explosions.
Never weld close to flammable materials.
Flammable materials must be at least 11 metres (36 ft. 1.07 in.) away from the
arc, or alternatively covered with an approved cover.
A suitable, tested fire extinguisher must be available and ready for use.
Sparks and pieces of hot metal may also get into adjacent areas through small
gaps or openings. Take appropriate precautions to prevent any danger of injury or fire.
Welding must not be performed in areas that are subject to fire or explosion or
near sealed tanks, vessels or pipes unless these have been prepared in accordance with the relevant national and international standards.
Do not carry out welding on containers that are being or have been used to
store gases, propellants, mineral oils or similar products. Residues pose an
explosive hazard.
An electric shock is potentially life threatening and can be fatal.
Do not touch live parts either inside or outside the device.
During MIG/MAG welding and TIG welding, the welding wire, the wirespool,
the feed rollers and all pieces of metal that are in contact with the welding wire
are live.
Always set the wirefeeder up on a sufficiently insulated surface or use a suitable, insulated wirefeeder holder.
Make sure that you and others are protected with an adequately insulated, dry
temporary backing or cover for the earth or ground potential. This temporary
backing or cover must extend over the entire area between the body and the
earth or ground potential.
All cables and leads must be secured, undamaged, insulated and adequately
dimensioned. Replace loose connections and scorched, damaged or inadequately dimensioned cables and leads immediately.
Use the handle to ensure the power connections are tight before every use.
In the case of power cables with a bayonet connector, rotate the power cable
around the longitudinal axis by at least 180° and pre-load.
Do not wrap cables or leads around the body or parts of the body.
The electrode (rod electrode, tungsten electrode, welding wire, etc.) must
- never be immersed in liquid for cooling
- Never touch the electrode when the power source is switched on.
Double the open circuit voltage of a power source can occur between the
welding electrodes of two power sources. Touching the potentials of both electrodes at the same time may be fatal under certain circumstances.
Arrange for the mains cable to be checked regularly by a qualified electrician
to ensure the ground conductor is functioning properly.
The device must only be operated on a mains supply with a ground conductor
and a socket with a ground conductor contact.
14
Meandering welding currents
EMC Device Classifications
Operating the device on a grid without a ground conductor and in a socket
without a ground conductor contact will be deemed gross negligence. The
manufacturer shall not be held liable for any damage arising from such usage.
If necessary, provide an adequate earth connection for the workpiece.
Switch off unused devices.
Wear a safety harness if working at height.
Before working on the device, switch it off and pull out the mains plug.
Attach a clearly legible and easy-to-understand warning sign to the device to
prevent anyone from plugging the mains plug back in and switching it on
again.
After opening the device:
- Discharge all live components
- Ensure that all components in the device are de-energised
If work on live parts is required, appoint a second person to switch off the main
switch at the right moment.
If the following instructions are ignored, meandering welding currents can develop with the following consequences:
- Fire hazard
- Overheating of parts connected to the workpiece
- Irreparable damage to ground conductors
- Damage to device and other electrical equipment
Ensure that the workpiece is held securely by the workpiece clamp.
Attach the workpiece clamp as close as possible to the area that is to be welded.
If the floor is electrically conductive, the device must be set up with sufficient
insulating material to insulate it from the floor.
If distribution boards, twin-head mounts, etc., are being used, note the following: The electrode of the welding torch / electrode holder that is not used is
also live. Make sure that the welding torch / electrode holder that is not used
is kept sufficiently insulated.
In the case of automated MIG/MAG applications, ensure that only an insulated
wire electrode is routed from the welding wire drum, large wirefeeder spool or
wirespool to the wire-feed unit.
Devices in emission class A:
- Are only designed for use in industrial settings
- Can cause line-bound and radiated interference in other areas
Devices in emission class B:
- Satisfy the emissions criteria for residential and industrial areas.
This is also true for residential areas in which the energy is supplied from the public low-voltage mains.
EMC device classification as per the rating plate or technical data.
15
EN
EMC measures
EMF measures
Specific hazards
In certain cases, even though a device complies with the standard limit values
for emissions, it may affect the application area for which it was designed (e.g.
when there is sensitive equipment at the same location, or if the site where the
device is installed is close to either radio or television receivers).
If this is the case, then the operator is obliged to take appropriate action to rectify the situation.
Check and evaluate the immunity to interference of nearby devices according
to national and international regulations. Examples of equipment that may be
susceptible to interference from the device include:
- Safety devices
- Power, signal and data transfer lines
- IT and telecommunications devices
- Measuring and calibrating devices
Supporting measures for avoidance of EMC problems:
1. Mains supply
- If electromagnetic interference arises despite correct mains connection, additional measures are necessary (e.g. use a suitable line filter).
2. Welding power leads
- must be kept as short as possible
- must run close together (to avoid EMF problems)
- must be kept well apart from other leads
3. Equipotential bonding
4. Earthing of the workpiece
- If necessary, establish an earth connection using suitable capacitors.
5. Shielding, if necessary
- Shield off other nearby devices
- Shield off entire welding installation
Electromagnetic fields may pose as yet unknown risks to health:
- effects on the health of others in the vicinity, e.g. wearers of pacemakers
and hearing aids
- wearers of pacemakers must seek advice from their doctor before approaching the device or any welding that is in progress
- for safety reasons, keep distances between the welding cables and the
welder's head/torso as large as possible
- do not carry welding cables and hosepacks over the shoulders or wind
them around any part of the body
Keep hands, hair, clothing and tools away from moving parts. For example:
- Fans
- Cogs
- Rollers
- Shafts
- Wirespools and welding wires
Do not reach into the rotating cogs of the wire drive or into rotating drive components.
Covers and side panels may only be opened/removed while maintenance or
repair work is being carried out.
16
During operation
- Ensure that all covers are closed and all side panels are fitted properly.
- Keep all covers and side panels closed.
The welding wire emerging from the welding torch poses a high risk of injury
(piercing of the hand, injuries to the face and eyes, etc.).
Therefore always keep the welding torch away from the body (devices with
wire-feed unit) and wear suitable protective goggles.
Never touch the workpiece during or after welding - risk of burns.
Slag can jump off cooling workpieces. The specified protective equipment
must therefore also be worn when reworking workpieces, and steps must be
taken to ensure that other people are also adequately protected.
Welding torches and other parts with a high operating temperature must be allowed to cool down before handling.
Special provisions apply in areas at risk of fire or explosion - observe relevant
national and international regulations.
Power sources for work in areas with increased electric risk (e.g. near boilers)
must carry the "Safety" sign. However, the power source must not be located
in such areas.
Risk of scalding from escaping coolant. Switch off cooling unit before disconnecting coolant flow or return lines.
Observe the information on the coolant safety data sheet when handling coolant. The coolant safety data sheet may be obtained from your service centre
or downloaded from the manufacturer's website.
Use only suitable load-carrying equipment supplied by the manufacturer when
transporting devices by crane.
- Hook chains and/or ropes onto all suspension points provided on the
load-carrying equipment.
- Chains and ropes must be at the smallest angle possible to the vertical.
- Remove gas cylinder and wire-feed unit (MIG/MAG and TIG devices).
If the wire-feed unit is attached to a crane holder during welding, always use
a suitable, insulated wirefeeder hoisting attachment (MIG/MAG and TIG devices).
If the device has a carrying strap or handle, this is intended solely for carrying
by hand. The carrying strap is not to be used if transporting with a crane, counterbalanced lift truck or other mechanical hoist.
All lifting accessories (straps, handles, chains, etc.) used in connection with
the device or its components must be tested regularly (e.g. for mechanical
damage, corrosion or changes caused by other environmental factors).
The testing interval and scope of testing must comply with applicable national
standards and directives as a minimum.
Odourless and colourless shielding gas may escape unnoticed if an adapter
is used for the shielding gas connection. Prior to assembly, seal the deviceside thread of the adapter for the shielding gas connection using suitable Teflon tape.
17
EN
Factors affecting
welding results
Danger from
shielding gas cylinders
Safety measures
at the installation
location and during transport
The following requirements with regard to shielding gas quality must be met if
the welding system is to operate in a correct and safe manner:
- Size of solid matter particles < 40 μm
- Pressure dew point < -20 °C
- Max. oil content < 25 mg/m³
Filters must be used if necessary.
NOTE! There is an increased risk of soiling if ring mains are being
used
Shielding gas cylinders contain gas under pressure and can explode if damaged. As the shielding gas cylinders are part of the welding equipment, they
must be handled with the greatest of care.
Protect shielding gas cylinders containing compressed gas from excessive
heat, mechanical impact, slag, naked flames, sparks and arcs.
Mount the shielding gas cylinders vertically and secure according to instructions to prevent them falling over.
Keep the shielding gas cylinders well away from any welding or other electrical
circuits.
Never hang a welding torch on a shielding gas cylinder.
Never touch a shielding gas cylinder with an electrode.
Risk of explosion - never attempt to weld a pressurised shielding gas cylinder.
Only use shielding gas cylinders suitable for the application in hand, along with
the correct and appropriate accessories (regulator, hoses and fittings). Only
use shielding gas cylinders and accessories that are in good condition.
Turn your face to one side when opening the valve of a shielding gas cylinder.
Close the shielding gas cylinder valve if no welding is taking place.
If the shielding gas cylinder is not connected, leave the valve cap in place on
the cylinder.
The manufacturer's instructions must be observed as well as applicable national and international regulations for shielding gas cylinders and accessories.
A device toppling over could easily kill someone. Place the device on a solid,
level surface such that it remains stable
- The maximum permissible tilt angle is 10°.
Special regulations apply in rooms at risk of fire or explosion
- Observe relevant national and international regulations.
Use internal directives and checks to ensure that the workplace environment
is always clean and clearly laid out.
Only set up and operate the device in accordance with the degree of protection shown on the rating plate.
When setting up the device, ensure there is an all-round clearance of 0.5 m (1
ft. 7.69 in.) to ensure that cooling air can flow in and escape unhindered.
When transporting the device, observe the relevant national and local guidelines and accident prevention regulations. This applies especially to guidelines
regarding the risks arising during transport.
18
Safety measures
in normal operation
Before transporting the device, allow coolant to drain completely and detach
the following components:
- Wire-feed unit
- Wirespool
- Shielding gas cylinder
After transporting the device, the device must be visually inspected for damage before commissioning. Any damage must be repaired by trained service
technicians before commissioning the device.
Only operate the device if all safety devices are fully functional. If the safety
devices are not fully functional, there is a risk of
- injury or death to the operator or a third party,
- damage to the device and other material assets belonging to the operator,
- inefficient operation of the device.
Any safety devices that are not functioning properly must be repaired before
switching on the device.
Never bypass or disable safety devices.
Before switching on the device, ensure that no one is likely to be endangered.
Check the device at least once a week for obvious damage and proper functioning of safety devices.
Always fasten the shielding gas cylinder securely and remove it beforehand if
the device is to be transported by crane.
Only the manufacturer's original coolant is suitable for use with our devices
due to its properties (electrical conductibility, anti-freeze agent, material compatibility, flammability, etc.).
Only use suitable original coolant from the manufacturer.
Do not mix the manufacturer's original coolant with other coolants.
The manufacturer accepts no liability for damage resulting from use of a different coolant. In addition, all warranty claims will be forfeited.
The coolant can ignite under certain conditions. Transport the coolant only in
its original, sealed containers and keep well away from any sources of ignition.
Used coolant must be disposed of properly in accordance with the relevant national and international regulations. The coolant safety data sheet may be obtained from your service centre or downloaded from the manufacturer's
website.
Check the coolant level before starting to weld and while the system is still
cool.
19
EN
Commissioning,
maintenance and
repair
Safety inspection
Disposal
It is impossible to guarantee that bought-in parts are designed and manufactured to meet the demands made of them, or that they satisfy safety requirements.
- Use only original spare and wearing parts (also applies to standard parts).
- Do not carry out any modifications, alterations, etc. to the device without
the manufacturer's consent.
- Components that are not in perfect condition must be replaced immediately.
- When ordering, please give the exact designation and part number as
shown in the spare parts list, as well as the serial number of your device.
The housing screws provide the ground conductor connection for earthing the
housing parts.
Only use original housing screws in the correct number and tightened to the
specified torque.
The manufacturer recommends that a safety inspection of the device is performed at least once every 12 months.
The manufacturer recommends that the power source be calibrated during the
same 12-month period.
A safety inspection should be carried out by a qualified electrician
- after any changes are made
- after any additional parts are installed, or after any conversions
- after repair, care and maintenance has been carried out
- at least every twelve months.
For safety inspections, follow the appropriate national and international standards and directives.
Further details on safety inspection and calibration can be obtained from your
service centre. They will provide you on request with any documents you may
require.
Do not dispose of this device with normal domestic waste! To comply with the
European Directive on Waste Electrical and Electronic Equipment and its implementation as national law, electrical equipment that has reached the end of
its life must be collected separately and returned to an approved recycling facility. Any device that you no longer require must either be returned to your
dealer or given to one of the approved collection and recycling facilities in your
area. Ignoring this European Directive may have potentially adverse affects on
the environment and your health!
20
Safety symbols
Data protection
Copyright
Devices with the CE mark satisfy the essential requirements of the low-voltage
and electromagnetic compatibility directive (e.g. relevant product standards
from the EN 60 974 series).
Fronius International GmbH declares that the device complies with directive
2014/53/EU. The full text of the EU Declaration of Conformity is available from
the following website: http://www.fronius.com
Devices with the CSA test mark satisfy the requirements of the relevant standards in Canada and the USA.
The user is responsible for the safekeeping of any changes made to the factory settings. The manufacturer accepts no liability for any deleted personal
settings.
Copyright of these operating instructions remains with the manufacturer.
The text and illustrations are all technically correct at the time of printing. We
reserve the right to make changes. The contents of the operating instructions
shall not provide the basis for any claims whatsoever on the part of the purchaser. If you have any suggestions for improvement, or can point out any
mistakes that you have found in the instructions, we will be most grateful for
your comments.
General information
23
EN
General
Device concept
TransTig 2200 Job, MagicWave 1700 Job and
MagicWave 2200 Job with cooling unit
The MagicWave (MW) 1700 / 2200 / 2500 /
3000 / 4000 / 5000 and TransTig (TT) 800 /
2200 / 2500 / 3000 / 4000 / 5000 TIG power
sources are completely digitised, microprocessor controlled inverter power sources.
The modular design and potential for system add-ons ensure a high degree of flexibility. The devices can be adapted to any
situation.
The straightforward operating concept
means that essential functions can be seen
at a glance and adjusted as required.
A standardised LocalNet interface makes it
easy to connect digital system add-ons (e.g.
JobMaster TIG welding torches, robot welding torches, remote control units, etc.).
Automatic cap shaping for AC welding with
MagicWave power sources takes the diameter of the tungsten electrode into account
to help produce optimum results.
The power sources are generator-compatible. They are exceptionally sturdy in day-today operation thanks to the protected control elements and their powder-coated
housings.
To optimise the ignition sequence in TIG AC
welding, the MagicWave takes account not
only of the diameter of the electrode, but
also of its temperature, calculated with reference to the preceding welding and welding off-times.
MagicWave 3000 Job with cooling unit and
MagicWave 2500 Job
TransTig 5000 Job and MagicWave 5000 Job,
both with cooling unit and trolley
24
Functional principle
The central control and regulation unit of the power sources is coupled with a digital signal
processor. The central control and regulation unit and signal processor control the entire
welding process.
During the welding process, the actual data is measured continuously and the device responds immediately to any changes. Control algorithms ensure that the desired target
state is maintained.
This results in:
- a precise welding process,
- exact reproducibility of all results
- excellent weld properties.
Field of application
The devices are used in workshops and industry for manual and automated TIG applications with unalloyed and low-alloy steel and high-alloy chrome-nickel steels.
The MagicWave power sources perform exceptionally well when it comes to welding aluminium, aluminium alloys and magnesium due to the variable AC frequency.
25
EN
Warning notices
on the device
US power sources come with extra warning notices affixed to the device. The warning notices must NOT be removed or painted over.
US version of power source with additional warning notices, e.g. MagicWave 2200
26
System components
General The TransTig and MagicWave power sources can be used with a wide variety of system
add-ons and options.
Overview
System add-ons and options
Item Description
(1) Power sources
(2) Cooling units
(3) Trolley with gas cylinder holder
(4) Pedal remote control unit
(5) TIG welding torch Standard / Up/Down
(6) JobMaster TIG welding torch
JobMaster TIG welding torch functions in conjunction with power sources:
- welding current indicator on the welding torch
- UP/Down control
(7) Remote control units and robot accessories
(8) Grounding (earthing) cable
(9) Electrode cable
FRONIUS
A
V
(1)
(6)
(7)
(2)
(3)
(9)
(8)
(5)
(4)
Control elements and connections
29
EN
Description of the control panels
General The key feature of the control panel is the logical way in which the control elements are
arranged. All the main welding parameters needed for day-to-day working can easily be:
- selected using the buttons
- altered with the adjusting dial
- shown during welding on the digital display.
Safety
Overview
NOTE! Due to software updates, you may find that your device has certain func-
tions that are not described in these operating instructions or vice versa. Individual illustrations may also differ slightly from the actual controls on your device, but
these controls function in exactly the same way.
WARNING! Operating the equipment incorrectly can cause serious injury and
damage. Do not use the functions described until you have thoroughly read and
understood the following documents:
- these operating instructions
- all the operating instructions for the system components, especially the safety rules
"Description of the control panels" is composed of the following sections:
- MagicWave control panel
- TransTig control panel
- Key combinations - special functions
MagicWave control panels: TransTig control panels:
(1) MW 1700 / 2200 (4) TT 2200
(2) MW 2500 / 3000 (5) TT 2500 / 3000
(3) MW 4000 / 5000 (6) TT 4000 / 5000
(1)
(3)
(2)
(4)
(6)
(5)
30
MagicWave control panel
MagicWave control panel
No. Function
(1) Left digital display
(2) HOLD indicator
at the end of each welding operation, the actual values for the welding current and
voltage are stored and the Hold indicator lights up.
The Hold indicator refers to the last value reached by the main current I1. As soon
as any other welding parameter is selected, the Hold indicator goes off. The "Hold"
values will continue to be available, however, if welding parameter I1 is selected
again.
The Hold indicator is cleared when:
- a new welding operation is started
- the welding current I1 is set
- the mode is changed
- the welding process is changed
NOTE Hold values are not output if:
- the main current phase is never reached,
or
- a pedal remote control is used.
(3) Right digital display
(2)
(11)
(5)
(8)
(10) (9)
(3)
(12)
(1) (4)
(7)
(6)
(13)
(15)
(14)
Loading...