Certific ate of Compliance
Certificate: 80027758 Master Contract: 203213
Project: 80143907 Date Issued: 2023-01-09
Issued to: Fronius International GmbH
Guenter Fronius Strasse 1
Wels-Thalheim, 4600
AUSTRIA
Attention: Josef Feichtinger
The products listed below are eligible to bear the CSA Mark shown with
adjacent indi cators 'C' and 'US' for Canada and US or with adjacent
indicator 'US' for US only or without either indicator for Canada only.
Issued by: Alessandro Raspatel li
PRODUCTS
CLASS 5611 03 - WELDING M ACHINES
CLASS 5611 83 - WELDING M ACHINES - CERTIFIED TO U.S. STANDARDS
PART A:
Model TransTig 170 (Alternate name TT 170) followed by suffixes, inverter type welding power sources for TIG
and Rod Electrode welding processes, rat ed as follows:
Input: 230V, 15A(max.), 12A(eff.); 1 phase, 50 or 60Hz Output: 15.6V, 140A, 100% Duty Cycle; 16.2V, 155A,
60% Duty Cycle; 16.8V, 170A, 40% Duty Cycle
Input: 120V, 23A(max.), 15A(eff.); 1 phase, 50 or 60Hz Output: 14.0V, 100A, 100% Duty Cycle; 14.8V, 120A,
60% Duty Cycle; 15.6V, 140A, 40% Duty Cycle
Max. OCV: 97Vpeak
IP-23
PART B:
Model TransTig 210 (Alternate name TT 210) followed by suffixes, inverter type welding power sources for TIG
and Rod Electrode welding processes, rat ed as follows:
DQD 507 Rev. 2019-04-30 © 2018 CSA Group. All rights reserved. Page 1
Certificate: 80027758
Project: 80143907
Master Contract: 203213
Date Issued: 2023-01-09
Input: 230V, 20A(max.), 14A(eff.); 1 phase, 50 or 60Hz Output: 16.4V, 160A, 100% Duty Cycle; 17.4V, 185A,
60% Duty Cycle; 18.4V, 210A, 40% Duty Cycle
Input: 120V, 29A(max.), 18A(eff.); 1 phase, 50 or 60Hz Output: 14.8V, 120A, 100% Duty Cycle; 16.0V, 150A,
60% Duty Cycle; 16.8V, 170A, 40% Duty Cycle
Max. OCV: 97Vpeak
IP-23
NOTE:
The equipment is generally provided with power plug and cord. If the equipment is not provided with power plug,
suitable power plug need to be selected per approval of the Local Inspection Authority.
APPLICABLE REQUIREMENTS
CSA C22.2 No. 60974-1:19 Arc Welding Equipment Part 1: Welding Power Sources
ANSI/NEMA/IEC 60974-1:2019 Arc Welding Equipment Part 1: Welding Power Sources
MARKINGS
The manufacturer is required to apply the following markings:
• Products shall be marked with the markings specified by the particular product standard.
• Products certified for Canada shall have all Caution and Warning markings in both English and French.
Additional bilingual markings not covered by the product standard(s) may be required by the Authorities Having
Jurisdiction. It is the responsibility of the manufacturer to provide and apply these additional markings, where
applicabl e, in accordance with the requir ements of those authoriti es.
The products listed are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and
US (indicating that products have been manufactured to the requirements of both Canadian and U.S. Standards) or
with adjacent indicator 'US' for US only or without either indicator for Canada only.
See Ill. 13 for Control Panel.
Additional Markings:
The date of the manufacture i s traceable through a date-coded serial number.
The polarity of the output terminals is marked.
The “ON” and “OFF” positions of the power switch shall be marked (I-O, ON-OFF, etc.)
DQD 507 Rev. 2016-02-188-11-12 © 2018 CSA Group. All rights reserved. Page 2
Loading...