Fri-Jado TG110-M, TG330-M, TG550-M Installation, Operation And Maintenance Instructions
INSTRUCTIONS
Installation, operation and care of
www.frijado.com
Part-number form 912.3474 / 0808
TG - ROTISSERIE OVEN MODELS
MODELS
Manual controls TG50- M
TG110-M
TG330-M
TG550-M
Model TG330-M
● IMPORTANT ●
READ BEFORE USING ROTISSERIE/WARMER
2
MODELS
Model Oven TG50-M Model Oven TG110-M
Model Oven TG330-M Model Oven TG550-M
3
TABLE OF CONTENTS
MODELS .................................................................................................................... 2
GENERAL .................................................................................................................. 5
FEATURES AND OPTIONS............................................................................................ 5
INSTALLATION.......................................................................................................... 6
LOCATION................................................................................................................. 6
LEVELING.................................................................................................................. 6
LEGS/CASTERS.......................................................................................................... 6
A
SSEMBLY ................................................................................................................ 7
S
UPPLEMENTAL INSTALLATION INSTRUCTIONS.............................................................. 7
INSTALLATION CODES AND STANDARDS........................................................................ 8
ELECTRICAL CONNECTIONS ........................................................................................ 8
ELECTRICAL DATA...................................................................................................... 9
BEFORE FIRST USE............................................................................................... 10
OPERATION ............................................................................................................ 10
OVEN CONTROLS TG50-M....................................................................................... 11
OVEN CONTROLS TG110-M, TG330-M AND TG550-M ............................................. 12
PREPARING THE PRODUCT.................................................................................. 14
L
OADING PRODUCTS ONTO ACCESSORIES.................................................................. 14
L
OADING PRODUCTS ONTO SPITS .............................................................................. 15
LOADING ACCESSORIES INTO THE OVEN (TG330-M AND TG550-M)............................ 17
LOADING ACCESSORIES INTO THE OVEN (TG50-M) .................................................... 19
LOADING ACCESSORIES INTO THE OVEN (TG110-M) .................................................. 20
UNLOADING ACCESSORIES FROM THE OVEN ............................................................... 20
SUGGESTED ROASTING GUIDELINES .......................................................................... 22
EMPTYING GREASE DRAWER..................................................................................... 22
CLEANING............................................................................................................... 24
CLEANING STAINLESS STEEL SURFACES..................................................................... 25
CLEANING NON-STICK COATED SURFACES .................................................................. 25
CLEANING GREASE DRAWER..................................................................................... 26
CLEANING QUARTZ LAMPS ........................................................................................ 26
M
ONTLY CLEANING (OR MORE OFTEN IF NECESSARY).................................................. 27
MAINTENANCE ....................................................................................................... 27
4
Installation, Operation and Care of
TG ROTISSERIE OVEN MODELS
BEFORE USING THE OVEN FOR THE FIRST TIME,
CAREFULLY READ THIS ENTIRE MANUAL.
IMPORTANT NOTICE: The user is responsible for reading and
following these instructions to ensure the safe and proper
installation, operation, and maintenance of the ovens and warmers.
The manufacturer expressly disclaims any and all liability for any
and all damage or injury resulting from failure to follow and comply
with these instructions, or from failure to exercise reasonable care
in the handling, operation, cleaning, and repair of the ovens and
warmers, and failure to explicitly include any warnings or
instructions in this manual shall not give rise to any claim for
damages. If you have any questions concerning the installation,
operation, care, or maintenance of the ovens or warmers that are
not covered by these instructions, please contact the manufacturer
at:
Fri-Jado Inc.
877 – 374 – 5236 (toll free)
SAFETY SYMBOLS
The following symbols are used throughout this manual to alert the user to specific
hazards:
= WARNING
Failure to observe this warning may result in personal injury, death, or
equipment damage.
= WARNING
Risk of electrical shock. Failure to observe this warning may result in
personal injury, death, or equipment damage.
= WARNING
Hot! Risk of burns. Wear heat-protective gloves.
Please read the safety instructions in this manual carefully and use the ovens
and warmers only as described in these instructions to avoid injury or damage.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE!
© 2005 Fri-Jado BV, Etten-Leur, The Netherlands
Customers are permitted to copy these instructions for private use.
5
GENERAL
The TG Series Rotisserie Ovens feature stainless steel interior and exterior for ease
of cleaning. The rotor system, spits, chicken racks or baskets and combination
convection and radiant heat provide thorough cooking and even browning yet
eliminate hot spots. Oven controls provide “Manual” operation where the END TIME
or PROCESS TIME can be preset.
Model TG50-M:
The grease drawer can be completely removed for cleaning. A tempered glass door
on the operator/customer side, and quartz lighting promote visual appeal and
stimulate customer interest.
Model TG110-M, TG330-M and TG550-M:
The grease drawer has a drain plug for elimination of excess fat and can be
completely removed for cleaning. Tempered glass doors, both front and back, and
quartz lighting promote visual appeal and stimulate customer interest.
Doors can be re-hinged; contact your local service agency.
Ovens are available in following seizes:
TG50 - Oven with 3 spits (6-9 chickens)
TG110 - Oven with 4 spits (12-20 chickens)
TG330 - Oven with 7 spits (28-35 chickens)
TG550 - Oven with 14 spits (56-70 chickens)
FEATURES AND OPTIONS
Quantity per oven. All parts are optional.
Chicken rack
Spit Basket Turkey
Spit
4 rack 5 rack Meat
forks
TG50-M NA 3 NA NA NA 3
TG110-M NA 4 1 NA NA 4
TG330-M 7 7 1 7 7 7
TG550-M 14 14 2 14 14 14
Do not mix accessories on the rotor.
THIS PRODUCT HAS A ONE-YEAR WARRANTY FOR PARTS AND LABOR. PARTS THAT ARE
NOT COVERED BY THIS WARRANTY ARE LAMPS AND GLASS. THE SOLE AND EXCLUSIVE
REMEDY OF THE PURCHASER IS LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT,
AT THE SOLE DISCRETION OF FRI-JADO, INC. THIS LIMITED REPAIR AND REPLACEMENT
WARRANTY IS THE SOLE WARRANTY PROVIDED FOR THIS PRODUCT AND FRI-JADO, INC.
EXPRESSLY EXCLUDES AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY IS VOID
WHERE DAMAGE RESULTS FROM IMPROPER USE OF THE PRODUCT OR THE PURCHASER
USES THE PRODUCT IMPROPERLY.
6
INSTALLATION
Immediately after unpacking the oven, check for possible shipping damage. If oven is
found to be damaged after unpacking, save the packaging material and contact the
carrier within 15 days of delivery.
TG550-M and TG330-M are secured to the skid with four screws which must be
removed.
WARNING
Prior to installation, test the electrical service to assure that it agrees with the
specifications on the machine data plate located on the right side panel near
the controls. (for the TG50-M on the upper right if you face the back of the
oven)
LOCATION
The oven may be placed where cooking may be observed to enhance customer
awareness, but must be installed on a level surface if the oven or warmer is not on
casters.
The installation location must allow adequate clearances for servicing and for proper
operation of the front and rear doors.
WARNING
A minimum wall clearance of 10” (254 mm) from any glass, and 4" (102 mm)
from each side panel must be maintained.
Keep the space around the bottom and the ventilation openings in the top of the units
free of obstacles to guarantee a good air flow in the electrical compartment.
LEVELING
1. Place oven in the installation position and place a carpenter's level on top of
the oven.
2. Turn the adjustable legs to level the oven front-to-back and side-to-side.
WARNING
The oven should not be accessible to the customer. Hot glass and parts can
cause burns.
LEGS/CASTERS
Counter models, TG110-M, TG220-M and TG330-M , are furnished with 11/2" legs.
TG550-M is furnished with 2 swivel and 2 locking swivel casters.
7
ASSEMBLY
Place the two bottom plates in the oven. The two plates slant to the middle to allow
fat to drip into the grease drawer.(See the above figure).
The TG5500-M bottom plates are the same size and equal to the TG330-M.
NOTE: Bottom plate on the customer side is smaller in the top unit of the TG550-M.
The model TG50-M does not feature removable bottom plates.
SUPPLEMENTAL INSTALLATION INSTRUCTIONS
(For model TG550-M)
WARNING
Safety standards require that, when this appliance is properly connected to the
electrical power supply using flexible conduit, adequate means be provided to limit
movement of the appliance without depending on or transmitting stress to the
electrical conduit. This means that, as part of the installation, the unit must be
secured to the building structure (typically either wall or floor) to limit the
movement of the appliance and, thus, helping to prevent damage to the conduit
during cleaning, maintenance and service operations.
A tether bracket, as shown in the figure below, is installed along with the caster to
one corner of the unit. The remaining open hole in the center of the tether bracket is
to be used to secure one end of the tether (locally supplied chain, cable, etc.). The
other end of the tether is to be secured to an anchoring point in the building structure.
Note: Length of tether must be shorter than the flexible conduit to make sure that
during appliance movement, no stress is transmitted to the conduit.
Following installation, check to confirm that, when the appliance is
moved to the limits of the tether in each direction, no stress is
transmitted to the electrical conduit.
8
INSTALLATION CODES AND STANDARDS
In the United States, all STG series ovens and STW series Warmers or combinations
must be installed according to the following codes:
State and local codes.
National Electric Code, ANSI/NFPA (latest edition). Copies may be obtained from the
National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.
In Canada, all STG series ovens and STW series Warmers or combinations must be
installed according to the following codes:
Local codes.
Canadian Electric Code, CSA C22.1 (latest edition) available from the Canadian
Standard Association, 5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada
L4W 5N6.
ELECTRICAL CONNECTIONS
WARNING
Electrical and grounding connections must comply with the applicable
portions of the national electrical code and / or other local electrical codes.
WARNING
Disconnect electrical power supply and place a tag at the disconnect switch
indicating that you are working on the circuit.
WARNING
Appliances equipped with a flexible electric supply cord are provided with a
three- or four-prong grounding plug. This plug must be connected into a
properly grounded three- or four-prong receptacle. If the receptacle is not the
proper grounding type, contact an electrician. Do not remove the grounding
prong from this plug.
Access the electrical connection point by removing the side panel(s) where the
controls are located.
WARNING
Ensure that the electrical power supply agrees with the specifications on the
oven's data plate and complies with the wiring diagram, located behind the
oven side panel and under the drive motor
Refer to the ELECTRICAL DATA chart on the next page.
9
ELECTRICAL DATA
MODEL VOLTS HERTZ PHASE CIRCUIT SIZE*
(AMPS)
TG50-M 208
240
60
60
1
1
20
20
TG110-M 208
208
240
240
60
60
60
60
1
3
1
3
35
20
35
20
TG330-M 208
208
240
240
60
60
60
60
1
3
1
3
60
35
60
35
TG550-M 208
240
60
60
3
3
70
70
Maximum Circuit Breaker size / minimum circuit amperage compiled in accordance
with the National Electric Code (latest edition).
Loading...